2 short beeps at startup on a Dell Studio 540

Similar Questions

• At boot Dell Studio 540 running Vista, I get a warning that "Windows host process (Rundll32) has stopped working.

  After each start up my Dell Studio 540 with Vista, I get a warning that "Windows host process (Rundll32) has stopped working.  Although this 'fault' seems to have no obvious effect on the following operations, it is very annoying to have to clear the window. I applied the suggested solutions elsewhere, but without success either.  Can someone please help me - in simplistic terms that I am a silver surfer?  Thank you very much.

  * original title - yet another problem Rundll32 *.

  Thanks a lot for the guide. Finally, I've identified the problem via the boot as in the NVIDIA driver.  I've now updated that and everything seems to work fine - touch wood!

• I have a dell studio 540 with graphics card geforce 9800gt, realtek audio, no sound on HD TV

  I have a dell studio 540 with geforce 9800gt graphics card. When I connect the hdmi sometimes I hear, but after awhile, the sound does not work. Now I have no sound at all. When I hooked the HDMI first, I found a realtek window asking me to activate the sound via hdmi. I find it anymore this window. I can't get the sound to work at all now.  I even tried to use 3.5 mm with hdmi and got nothing. 3.5 worked when I plugged in the vga to tv cable, but the picture quality was awful. How will I know if my card grphx carries sound?

  Hello

  I suggest you try to update the latest drivers for the card sound and graphics card and see if it helps:
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  It will be useful.

• Dell Studio 540 no speakers or headphones Sound - win 10

  My Dell Studio 540 lost out to attached speakers.  I can't tell if the problem is caused by the upgrade to win 10 or if I experienced a motherboard failure a coincidence.  I tried a number of bugs that include uininstalling pilots, roll back drivers and even install Vista drivers original I have original system disks.  Nothing works.

  I see, looking at the acoustic, Panel output HDMI seems to work because I can see where it says sound when playing music.  However, I can't the speakers or headphones of entry to work.  Even if I try the speaker plugs into one of the entrances, the acoustic Panel still shows the headphones or speakers are not connected.

  So, how can I get the systΦme can recognize that speakers have been connected?  Is there another driver I can use.  So far, I've tried several driver Realtek and configurations, does not

  Apologies for the lack of your post. The Studio 540 has never been validated for Windows 10.

  

  My advice is to disable the Realtek HD audio integrated into Bios - Advanced - Integrated Peripherals. Then install a current PCIe x 1 sound card in a PCIe x 1 on the motherboard slots. His current card will provide 10 Windows drivers.

• Upgrade CPU Dell Studio 540 (current SLB9U)

  Hello!

  I have a desktop Dell Studio 540 I want to upgrade the CPU on (current CPU is SLB9U). I did it on my older Dell that I had before and it went well ("Shesmygordie" helped me on the back then).

  I think searhing the Swedish e - bay (named "Tradera.com").

  My setup is now as follows:

  Computer model Studio 540

  BIOS Editor Dell Inc.

  BIOS version 1.1.3

  Date of the BIOS 25/08/2009

  OS version Microsoft Windows 8.1 Pro

  Processor

  Manufacturer Pentium Dual-Core CPU E5300 @ 2.60 GHz

  Clock speed 2.6 Ghz

  L2 Cache size 2048

  Concerning

  Matti

  mattixx

  Yorkfield Quad Core Q9650 3.00 GHz, 12 MB, 1333 MHz FSB, E0, is the largest CPU supported by the Studio 540.

  A list of the other Inspiron 540 processors supported can be found here:

  http://en.community.Dell.com/support-forums/desktop/f/3514/p/19432795/20036722#20036722

  Bev.

• Dell Studio 540 Windows 7 X 64 install

  G ' Day,.

  I recently bought a Dell Studio 540 second hand, in private.  I am trying to install Windows 7 64 bit, for which I have a license, but have lost the installation media.  There was no media installation with the Dell printer.  I downloaded an ISO of digital river, the DVD burned, shot to the top of the installation on the PC.  But he asks a driver CD and not proceed with the windows installation.

  Where can I find this driver?  I searched on the section of downloads for serial number and nothing that seems to do the trick there.

  99/100 times there is no such driver.  This message indicates that your media is bad... try downloading, check the hash or use a download manager to ensure the integrity of the download. try to use different software, blank DVD, engravers to create the DVD... you can also try the installation via USB after re-downloaded ISO.  Once successful with this DVD, you will need to activate by phone from Microsoft (not Dell).

  Or you can ask a real installation of Dell DVD by (United States only):

  support.Dell.com/.../backupcd_form

• Satellite C650 - 15 d has three short beeps when starting

  pls help with sound error my PC startup.
  Satellite C650 - 15 d has three short beeps at startup.
  Does anyone know?

  Hello

  All devices are connected to the laptop?
  Disconnect all devices that are plugged into the Satellite and try to start again.
  The unit beeps three times yet?

• Dell Studio 540MT does not start, green power light on, but the Start button / clear stop completely

  Looking for assistance

  Have a Dell Studio 540MT (purchased in 2009), worked great until 2 weeks ago.   After a temporary system failure would not start.    The power light itself is green fixed.   The power button on the front panel is completely released.

  I read a lot of messages and other information about a similar problem.   Therefore, I did following:

  1. unplug everything, press the power button / stop for 1 minute and retries.   without success

  2. replace the CMOS battery.  without success

  3A jumps the Green and black 20 supply connection wire pins to motherboard.  It started immediately food, fans and hard drive.   so I assumed that the PSU has been authorized.

  4 replace the motherboard with a new mobo.  Curiously, in a first time, there was no change, but after about 2 minutes, the power button was working and power system.   Everything worked so very well.   I had also completely cleaned all the dust in the chassis and radiator, fan and had applied the thermal paster as directed by Artic Silver.   I even turned off after hours of race and restarted system.  Restarted, he noted that it took a couple times by pressing the power button to make it work.   Then the 2nd day I shut down the system by a normal shutdown through Win 7 and let rest for about 10 hours.   When tried to start/turning the power on again, same problem as the original problem... at first, before light power button would show amber flashing when first pressed the power button / stop, then once I unplugged the power cord and let it sit for 1 hour, the light power button showed no light, completely and again no restarts.

  5. I ordered a new power button cord (new)... This could be the problem and replacement will fix?   Is this a known problem that power button can cause this kind of problem?

  6 or is a problem of power supply?   But you wonder why the green light of the PSU and works very well when jumping the Green and black wire on the connector 20 pin?     Before I go buy a new power supply to other suggestions?

  Is there a known issue with button / stop itself and/or PSU on Dell Studio 540 MTs?

  Yes, the front panel can cause failure to start in some models, although I don't specifically remember if the 540 has been affected by this problem. Please let me know if the replacement resolves the problem.

  ATX power supplies should work. Here are the standard components of the Dell desktop computers.

• Dell dimension 9200 2 and lights 1-2-3 short beeps

  Hello

  I have a Dimension 9200 bought around 2008. About 3 weeks, I started having issues getting started, until the computer wouldn't start. Lights said a bad video card, so I took out the card nvidia 260 and put the original video card in and the computer worked OK with the original video card. After another week or two, would not start the computer. I bought a used motherboard and succeeded him. When I turned on the computer, I had 2 short beeps and 1-2-3 on on the Panel. The seller knew what was up, then I sent the motherboard back and got a replacement of the replacement card is in it, but it still gives me 2 short beeps and 1-2-3 is turned on. The power led is constantly Green

  While these beeps and lights mean together?

  Thank you.

  Frank

  Beep codes should be in groups of three, separated by a short break, for example, 1-pause-1-pause-1. So if you hear 2 beeps, who is not useful.

  Version of Windows?

  According to the Manual, G-G-G-(off) means "another failure", and:

  1. Ensure that all disk and CD/DVD cables are properly connected to the system board
  2. If there is an error message on your screen to identify a problem with a device (for example, floppy drive or hard drive), check the device to ensure that it works correctly
  3. If the operating system is trying to boot from a device (for example, floppy drive or hard drive), check the system configuration (see to make sure that the boot sequence is correct for the devices installed on your computer.

  While everything is done, and you are sure that everything is installed properly and cables connected properly, remove the battery from the motherboard and the power button press / hold for about 30 seconds before reinstalling the battery. Then see if it boots with only mouse, screen and keyboard connected.

  If still no go, you will have to strip to a minimum by removing all PCI cards, except known working video card all modules in memory except the one in slot 1, disconnect all drives except boot the disk hard, etc.. Do the "battery thing"and see if it boots now...»

• MacBook Air mid 2009 3 beeps at startup

  Hello world!

  I had a problem: after a few hours of videos online watch my book mac freezed with sound fixed.

  After that I pressed the power button and shut down the computer. After evil market see black screen and hear 3 beeps.

  Also: I have used all the key-combination to repair the situation, problem still there.

  P. S.

  ALT-CMD-P-R - give me long 3beeps - 3beeps short - long 3beeps

  And now I want to try a version:

  "Same for me here.

  My MacBook Air mid-2011 with 4 GB of RAM would be only 3 beeps on startup.

  "Put the logic card 8 minutes in the oven at 190 degrees celsius - was again very well then begin."

  of https://ru.ifixit.com/Answers/View/27783/3+beeps+on+start+up

  Dear Mac users, if you have and idea to fix my mac - please enter into this discussion.

  Good day!

  Problem with RAM.

  https://support.Apple.com/en-us/HT202768

  Please contact Apple.

• Satellite P300 - 13 M - beeps at startup

  Hello

  My laptop now and then beeps at startup and then I get a black screen (and can't do anything)
  The beepingsounds goes as follows: BEEEEEEEEEEEP BEEP BEEP (1 x long - 2 short)

  Anyone know what this could be?

  It is very annoying when I want to show my client project and all of a sudden the laptop no longer works...

  Thnx in advance

  Raey

  Hello!

  Beep codes mean that there is a faulty hardware component.
  It's not easy to tell what is the reason for this, but in your case I would try to exchange the RAM.

  If it doesn't work you should contact an ASP and ask for help. Technicians can check your laptop and exchanging all the necessary parts.
  On the Toshiba site, you can search the nearest ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Good bye

• Satellite A200 PSAFCA - Display went - hear 3 beeps at startup

  Hello

  I have Toshiba A200 PSAFCA-01K00J.
  Last night, I restarted the laptop and screen did not appear.
  Sometimes (not everytime) at the start, I can hear 3 beeps (1 very very short and 2 short beeps).
  And then the Windows operating system loads correctly. Can hear sound/music that plays Windows at startup.

  Have you tried 1 of 2 from memory, but always the same result. Tried to hook up the external monitor, but the monitor says "No Signal".

  Need to know what the problem is with the laptop. Please help/tips.

  Thank you.

  > Have tried 1 2 memory, but always the same result. Tried to hook up the external monitor, but the monitor says "No Signal".

  Maybe you should try FN + F5
  This key combination switches the screen external monitor output.

  But to be honest, this looks like a display problem.
  I recommend you contact the ASP in your country who would check the display

• Satellite A100 beep at startup

  My Satellite A100 still beeps at startup (or when he wakes up after hibernation) as if a key is pressed down, and it will not stop until I press one ' ~ ' key (just below "Esc"). In addition, it begins this character by typing in the field log-in on the start screen.

  Any ideas why this might happen?

  HI Maria,

  It seems to me that if the key is either stuck or is defective. It is possible that the keys are shorted or the rubber under the top key shared so that contacts of does not return to the open"" position.

  I suggest that you only contact authorized Service partner who can check the keyboard.

  Kind regards

• Z400: four short beeps

  Recently, I moved from xw4400 (second hand) Z400. The transfer was relatively easy: I moved from SSD from the old to the new computer and made a few adjustions. Everything is fine, except:

  1. after closing down (and usually before logon) a four short beeps is the herd. Computer passed all the test of the utility of diagnosis (downloaded from HP). I made two changes to the system: Add a card WiFi PCI fan fore (directly connected to the transformer unit, not MB) (not working as before - usually need to press Connect)

  2. at the time of startup, before the login screen, there is a wait of 5 to 10 seconds (black screen with a cursor in the upper left; a very short message 'Attempt to start hard drive', and then connect you). Interestingly, I tried a completely clean installation of Win 7 Pro, but a black screen remains.

  Any input will be greatly appreciated.

  Gojko,
  
  1. the Z400 sometimes will give a 4 beeps if the system is shut down, and if the power cord is pulled (or AC power supply is cut off by a switch on a power strip), then the power button is pressed a few seconds after turning off the power (with power still disconnected).  What is happening, the system will try to power upward after pressing the power button, use the small residual charge in the system.  There is not enough power for the system to start to give of false beeps "power."
  
  However, these beeps to the power down don't cause the system failure and do not prevent the system startup when the power supply is reconnected.  It looks like a failure, but it is not.
  Just to be sure, you do run on 120 or 240 VAC?
  The system has never failed to turn on when the system is plugged into a power outlet?
  
  2. a few start-up systems after a wait of 5 second or 10 with the cursor in the corner.  I don't know why this happens, but it is normal that on many systems.
  
  You said you took records previous and other elements of the xw4400.  You reinstall the operating system?  You update the drivers?  I recommend that you install the latest driver for chipset Z400 and other drivers, if you have not already done so.

• Inspiron 3650 does emit any beeps at startup upward. Does?

  Seems to work well, less than a week old. I was expecting a beep at startup upward, but I hear nothing (unless it is very quiet) I should wait for a beep code. Unable to find anything in this regard in the manual. I have a S2316H monitor with built-in speakers attached via the HDMI.

  Any thoughts appreciated please. Thank you.

  With more recent versions of the UEFI BIOS, there is no beep at the STATION, unless there is a problem. Now, the POST beep means generally: card system: the BIOS ROM failure.

  A while back, Dell has a brand-new model giving the 'normal' beep at the STATION, but confused users with the motherboard beep fault code beep.

  This led to many mothers unnecessarily replaced under warranty. Dell has subsequently removed the 'normal' beep to the STATION in a revision of the BIOS and saved the lives of many mothers!