2011 21 inch iMac won't start after the SSD upgrade

Similar Questions

• Qosmio G30-102 not start after the SSD upgrade

  I have 2 x 840 Pro 256 GB SSD to install in my machine which usually runs two drives independently.

  I used the software to Clone of Samsun to clone my C drive which has XP on it.

  The cloning was successful.

  On the installation of the new SSD, it will be now does not start and keeps cycling to the F12 boot screen.

  I tried all the options without result.
  Any ideas?

  Hello

  I had a similar experience with an upgrade of the SSD.
  I used exactly the same software and has been able to clone partitions of HARD drive to SSD drive and my cell phone did not start the system from the SSD system partition.

  I figured out that the C: partition on the SSD was not marked as active.
  How I solved this?

  Well, I put the SSD in the 2.5 external USB enclosure. Then I booted the laptop using the old HDD. I connected the external SSD drive to the USB port.
  Then I went to Windows disk management and could activate the C partition on the SSD drive.
  Then I replaced the HARD drive with SSD and could boot. :)

• HP mini 110-3500 laptop: computer laptop HP mini 110-3500 fails to start after the SSD upgrade

  Hello
  I recently bought a ' crucial 250 gb 2.5 "SSD and 2 GB of RAM (also by crucial), to upgrade my laptop HP mini 110-3500, who has been extremely slow. But unfortunately, the laptop refused to start when turned on. What can I do? I am very worried.
  Enkay1

  You answered. That's what I thought. You have DDR3L-1600 low voltage 1.35 volts. Low voltage will operate at a higher voltage (1.5 volts), but it is not the ideal memory for older hardware. Need memory DDR3-1333 name specified for the HP laptop. You can confirm or refute my diagnosis by putting in the memory of the old and see if it boots.

  It's the part number you need:

  621567 001

  http://www.eBay.com/ITM/2GB-compat-to-621567-001-A3803335-A4100445-A4427375-/230655741975?PT=LH_DefaultDomain_0&hash=item35b4275017

  

  Is your memory has 8 black on the side blocks or just 4? You want 8. Also if you have Windows 7 Starter, you can not use 2 GB of RAM.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Two iMacs does not start after the 10.11.4 update.

  Two iMacs does not start after the 10.11.4 update.  Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd.  He then gets stuck in a loop trying to start.  Tried to reset the SMC and LANDAU.  Without success.  Started in recovery mode and ran disk utility.  Discs said OK.  Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).)  Installation is finished but still once does not start.  Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater.  Installation seems to work, but once again, the macs will not start.  Same 'unexpected launchd sigkill' error.  A mac is now back working properly with 10.11.3 the other will be shortly.  Is there a problem with the accession?  Our COMPUTER support use Munki to get updates from one day to the next.  Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.

  More information: two bricks iMacs were late 2013 models.  A 21 "and a 27.  We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.

• iMac does not start after the last security update

  Hello

  After the last update my iMac (late 2009, El Capitan) does not start.

  The iMac starts he accepts my user and password entry, the loading bar stops at 80% and then nothing happens... after I turn off the iMac. Repeating this procedure change nothing.

  Does anyone have any advice for me?

  THX

  INTELLECTUAL PROPERTY

  a solution that helped me:

  Re: security update causes damaged Apps

• iMac does not start after the update of the Sierra...

  Don't know what to do. Sierra, just updated and now my system hangs during startup and turns off.

  Anyone else seen this? No idea what I can do?

  Try a safe boot. Otherwise, you might to reinstall macOS.

  ----------

  Stop your Mac. Use the power button if you wish. Now start with the SHIFT key is pressed. This will start in Safe Mode, with all extensions turned off. Safe mode is slow to start, so give it time, it checks a lot of tasks. If it works fine in Safe Mode, restart normally. If it works now, you are finished.

  If the problem comes back after a reboot, you may have an extension conflict. Disable all extensions via system preferences. To isolate which extension is at fault, turn on an extension at the same time, restart in the meantime, until you find bad.

• HP Envy curves 34-AO51 signature Edition: won't start after the mode 'sleep'.

  HP Envy curve signature 34-AO51 edition:

  After that my brand new computer starts in mode 'sleep' it will not restart without unpluging it and restart. Coming from a mac, it's ben very frustraiting... any recommendations? all the drivers have been manually updated.

  Hello again @Judochop,

  I replied to your other post yesterday, but this one has additional information that was not in the other...

  What you describe looks great the effects of quick start. You can try turning it off.  Please see: the Pros and Cons Windows 10 "quick commissioning" Mode - howtogeek.com, How to Turn On or Off quick startup in Windows 10 - tenforums.com.

  Please let me know if it works for you and if it does not solve your problem, please mark this message as a solution. Bravo would be appreciated as well.

• Vista won't start after the last update of Silverlight - restarts constantly

  I installed the latest version of Silverlight from Microsoft Update, July 21.  There are 2 updates, but the other would not move.  My computer worked nomally and later when I stopped it, I got the "Configuring updates... do not turn off your computer" message.  It seemed to take a while, so I went to bed and the next morning, I saw that the computer had finally stopped.  I started it and I got the message "configuration updates stage 3 of 3." 0% complete.  Do not turn off your computer. "After anywhere from 10 seconds to a few minutes, it restarts.  She's constantly - he keeps just reboot and it displays the updates configuration message.  In the System Recovery Options, Startup Repair indicates that everything is OK.  "System Restore" to go to the restore point previous does not work.  What can I do?  The only other option and restore utility is all erase and install the drive from the factory.

  I have Windows Vista, the latest service pack and updates.  I have F-Secure anti virus/firewall.

  He has also failed to the previous Microsoft Update a week or 2 but it gave an error code of that time.  I looked at the error to Microsoft code and it says that the update log was full and there was a command to enter to remedy.  I did that and installed the update and everything was fine.  Unfortuately I have more error code or order more.

  Perhaps related to this problem?  My computer is pretty much dead now after Silverlight updated because it constantly restarts.

  Don't boot from the XP CD.

  Do an ERD of VistaBootable of the info below:

  As is the case with most computers/laptops these days, they do not come with good Vista disc to repair only the recovery disks.

  As your grave in the category above, download the ISO on the link provided and make a bootdisk of it.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  You can make a tool to restart system, System Restore, etc. with it.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista repair disc.

  You can do a system restart tool, system, etc it restore.

  There is not a disk of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  Mick Murphy - Microsoft partner

• 2450 PE does not start after the memory upgrade attempt

  Hello

  I have a Dell PE 2450, which is an older system, but has been working well and has 4x256MB DIMM in there and the last BIOS A09.  I tried to replace the DIMM A slot with a stick of 512 MB, and at switching on, a message appears indicating the amount of system memory has changed, followed by messages of typical POST on versions of firmware, and "Two-processor 866 MHz...", but then the system just sits there.

  The subsequent reboot by pressing F2 is not get into Setup or F10 penetrates me in utility Mode despite repeated attempts to press F2 all few seconds, I put the original memory back deleted, hard drives, tried to start on a diskette, etc.. I've tried unplugging, etc as well.  NVRAM would somehow corrupted?  Is it possible to reset?

  Thank you

  Don

  
  

• Pictures on a new iMac won't start - he's trying to fix the photo library after the migration of my old iMac.  The two are running El Capitan

  Photos on my new iMac won't start - get an error message after trying to fix the photo library.  I just migrated all of my old iMac a new aid of Time machine backup.  Both are running OS 10.11 (El Capitan).

  Get an error message after trying to fix the photo library.

  What does this error message say?  Photos crash or exit gracefully?

  Where your iPhoto library that Library stored? In your pictures folder, or on an external drive?

  Try to copy the library of Photos directly without Time Machine. Connect the two Macs using your network and copy the old Mac to the new library, well as signed in on your new Mac.

  Then try to open this copy in Photos.

• Windows 7 won't start after secuity 12/10/2010 dates

  original title: updates security for 10/12/2010

  Windows 7 won't start after secuity 12/10/2010 dates

  Hello
   
  Follow these steps and check if that helps.
   
  Step 1:
   
  Remove all external devices and then try to start again.
   
  Step 2:
   
  Start your computer in safe mode and check if it starts.
   
  Step 3:
   
  If it starts in safe mode, and then try the system restore , safe mode.
   
  Let us know.
   
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Satellite L300 - will not start after the installation of Skype

  My Toshiba Satellite L300 won't start after installing Skype.
  This happened to someone else, and can I do?

  Thank you.

  I think Skype is probably the most used messenger and ideal application for communication.
  It is professionally designed and programmed. As you know in recent years, it has been offered in many different versions and it is always better and better.

  So I think that Skype itself is probably not the problem. I know that a lot of people also use Skype and I've never heard problem described.

  Anyway, what you can try is to remove Skype and try to install it again. Try also push the BONES at that earlier time. Maybe some Microsoft updates are responsible for the stability of the software.
  It's really not easy to say what the problem is here.

• Why my iMac turns so slowly after the upgrade of the Lion in El Capitan?

  Why my iMac turns so slowly after the upgrade of the Lion in El Capitan?

  Just what do slow down? Rotation beach balls?

  Run and view the results here so that we know more about your configuration.

  http://etrecheck.com/

  EtreCheck

  https://discussions.Apple.com/docs/doc-6172

• Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process.

  Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process, but do not remember.
  Tried running firefox.exe Pei but error message:

  XML parsing error: the undefined entity
  Location: chrome://mozapps/content/profile/profileSelection.xul
  Line 18, column 1:
  "< dialog < =" "^ =" "p =" "> < / dialogue >

  Running on Windows XP SP3. No problem whatsoever before moving to 27. Sending of Chrome that I can't open Firefox at all.

  Thank you, jschaer2000. In the meantime, he works. How long, we'll see ;-)

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2