2050a do not all photography print to size the still enormous borders selected

Similar Questions

• Speech recognition is not all sounds during installation of the wizard.

  Sound recorder works fine and I can record, save and play wav files.  CLS recognition requires all upward before use and the recording meter bar moves I read the sentence of the sample.  After that, I get the error that SR couldn't hear anything.  Help please.

  Hi BTKpickle,

  Welcome to Microsoft Answers Forum.

  There are several possible causes of the problem:

  ·         The microphone isn't close to capture your voice. Make sure that the microphone is positioned close enough and you speak directly into it.

  ·         The microphone is cut in. Some microphones have an external control for muting. Make sure that the mute control is disabled.

  ·         The microphone input level is too low. Make sure that the microphone input level is set correctly.

  Entry level to adjust the microphone

  1. Open Audio devices and sound themes by clicking Start , clicking onto Control Panel, hardware and sound, and then clicking its.

  2. click on the recording tab.

  3. double-click on the microphone you are using speech recognition.

  4. click on the tab levels and then use the slider to adjust the entry level for your microphone.

  ·         The microphone connections are not properly attached. Make sure that microphone cables are intact and unbroken. The connections to the computer can be loose, so unplug the wires and reconnect them by ensuring that they fit.

  ·         A different microphone is selected to be used with speech recognition. If you have more than one microphone installed on your computer, that bad could be selected to be used with speech recognition. Make sure that you use the microphone selected for speech recognition.

  Change which microphone is used with speech recognition

  1. Open Audio devices and sound themes by clicking Start , clicking onto Control Panel, hardware and sound, and then clicking its.

  2. click on the recording tab.

  3. Select the microphone that you want to use with speech recognition, and then click set as default.

  Check the documentation that came with the microphone for additional troubleshooting information.

  See if you are able to complete the installation wizard.

  For solutions to common problems with Windows speech recognition, see

  Troubleshoot speech recognition

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-speech-recognition-problems

  I hope this helps.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think

• Not all patterns are presented in the Application in MISP schemas

  Hello

  I try to use MISP (Database Migration Unicode Assistant) to assess potential problems for a conversion NLS_CHARACTER_SET and note that not all schemas are indicated in Application schemas folder in the Navigator Panel. Especially I want to scan.

  In my case, it's showing only 4 patterns when there is almost more than 10 + in the database.

  Everyone got to experience that too? Could not find anything on MISP known issues?

  Thank you

  Eduardo.

  Have you checked if the missing patterns have all columns of type VARCHAR2, CHAR, CLOB, or LONG?

  Thank you

  Sergiusz

• Printer 65000A problem: not all colors print.

  Installed new color cartridges in my printer 65000. Why not red print?

  H

  On the camera screen, press setup, access the report and press ok and go on the balance sheet of the printer and press ok again. Magenta (red) is printed on this one there? If this isn't the case, it could be a defective print head which may be replaced. The print head is in the magenta/cyan printhead.

• Brand new hp 5520 will not all colors print

  Got a new hp5520 and he was installing tonight.

  The only color it prints is black, even at testpages printers.

  Status report is only to show a line to black.

  State of ink on the screen is everything to the maximum.

  openings checked and cleaned the heads but still nothing.

  How can I get this thing to work?

  Changed to a new and get it running in minutes

• What is a good quality for photography printer without breaking the Bank?

  I mainly used HPs, but it seems lately that these break quickly. Their quality does not seem to be as good as it used to be. I also bought the big pack of best quality at Costco Kodak photo paper that they quit carrying and I can't seem to conclude that more.  When I think that I found the quality is NOT the same as it was when I bought it at Costco. I print my own prints up to 11 x 14.

  What is a favorite for all book? I used glossy, which is a good paper for Matt printing?

  In addition, for someone else, who uses much ink I did, Costco sells large inks, they have more and last so much longer than replacements you buy at Wal-Mart, Staples, etc.

  I'll buy a Dell XPS 8900 with the 6th generation of processor Intel Core i7-6700. Specifically, I buy this PC for my photography business and accounting transactions.

  Documents of Canon are very good. If you like try iced Pkatinum Pro. In addition, Red River papers are good. You can order a pack sampler of them.

• WE'RE NOT ALL OF YOUR UPDATE. THE NETWORK CONNECTION HAS BEEN LOST.

  You have the idea what to do. This happens, when I want to update something iStore and iTunes. THX

  Please launch the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  The title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  Click on the clear view icon in the toolbar. Then take an action that does not work the way you expect. Select all of the lines that appear in the Console window. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name or e-mail address, can appear in the log. Anonymize before posting.

  When you post the journal excerpt, an error message may appear on the web page: "you include content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• Not all programs are displayed on the taskbar at the bottom, they use to?

  For some reason any I no longer get open programs along the bottom of the desktop on the taskbar.  I use to get them all so I could pick each individually.  When I need to get to one that is open I have to close all those that have been opened after that I want to use.  I use to be able to open 4 or 5 programs so I could monitor the need, but is that actually a lot more work having close and then go back.

  Hi skier Craig,.

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You have security software installed on the computer?

  Method 1

  Check if the problem persists in safe mode and post back with the results.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Method 2

  If the problem does not persist in safe mode, then it is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.

  When you are prompted, click restart to restart the computer.

  Method 3

  If the steps above fail, then I suggest that you scan and remove any malware or computer virus infections and check if it helps.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx 

  You can also use Microsoft Security databases to scan your computer

  http://www.Microsoft.com/security/PC-security/MSE.aspx

  We would also like to view your desktop in order to better understand the issue.

  Please provide us with the screenshot of the office.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-security/how-do-i-post-a-screen-shot-on-this-forum/c86de820-C620-401c-A804-9f6337cd3053

• IPhone shows not all photos when connected to the computer

  I have an Iphone 5, with more than 800 photos in my camera. When I connect my phone to the computer and open DCIM, happens with 100APPLE, with only 46 photos in the folder, and that's it. I tried to use google reader to get photos from my phone by downloading the app on my phone, but when I tried to add the files it only came with the same 46 photos. I also had a problem where I can't delete photos on my computer when I'm in the Apple folder, and my photos come upwards with one! in a circle in my albums and I'm unable to send them anywhere, and when I click on them, they start to load (as they look blurry when there is the!) but never finished loading. I'm not sure if this is related to the problem, but it could limit. Thank you for your help.

  Here you will find a few troubleshooting steps If you can not import photos from your iPad, iPhone or iPod touch to your computer - Apple Support

• Photos only are not all transferred to Revel, though the message says that the move is completed

  I received a message saying that the move to Photoshop to Revel is completed.  There are 173 of my latest photos jpg, dated July 2012 - March, 2013, that have not been moved. It seems that these photos were not automatically saved and synct the way in which they should have by Photoshop. How can I get these pictures moved to Revel?

  Karen-

  Photoshop.com is always open, your migrated files are still there as well as in Revel. Take a look and see if the files you want to revel are there or not. As I've described above, it seems as if you have files in the elements that have never uploaded to Photoshop.com and therefore never have been migrated. It is likely that the process has worked as intended and you need to download the files remaining from your computer to Revel.

  Please let me know what you find.

  Thank you-

  Guinot

• Not all lines are displayed in the OBIEE answers

  Hello
  
  When I include a dimension column (PRODUCT) with my column of fact (AMT SALES), I have only one line of PRODUCT displayed.
  
  If I select only the PRODUCT column without any column of FACT, I get the list of all PRODUCT(25 rows).
  
  I used the query generated by OBIEE and he ran into my database and I get all the lists of products and the amount of sales. (25 lines).
  
  I guess my problem is in my RPD. But where in my RPD should I look for to debug this problem?
  
  Thank you.
  
  Published by: ssk1974 on January 11, 2011 13:09

  It is probably correct behavior - you probably only have an existing product in your fact table? If you want to see all the lists of products as well as $0 for the facts, you will need to do an outer join between the dimension and the fact.

  Of course, if your fact table has other products, there are another problem - perhaps joined Sun on the wrong column name or something.

  Hope this helps,
  Scott

• I have a hp officejet 4215v all-in-one I can print from my computer, but not for my printer

  I'm unable to copy the documents from my printer.  I am able to copy from the computer.  I also can not uninstall and reinstall printer because it does not appear in Add/Remove programs.

  I'm sorry you have a problem with the printer.

  Do you receive an error message when you try to copy a document from the printer itself?

  If you are not able to print/copy of the printer itself, uninstalling and reinstalling will not help. It would be a problem with the hardware with the printer.

  Try to print a self-test page or printer the printer status report.

  Perform a hard reset. Unplug the power cord at the back. Leave for 30 seconds and plug it back.

• When I connect to sometimes see not all discussions

  Sometimes when I am connected to a listening mode a question I see not all threads.

  

  In the screen grab above is a question I commented, I'm not connected in the browser on the left and you can see two comments, (there where another two below this one) and memory here where about 10 comments total.

  In the right browser I am connected but do not see the last 3 comments that this browser is only show 7 comments.

  I know that when you are not connected to see you in the order and no nested comments, but this does not count the number of comment being different.

  This seems to be a recurring problem that arises from time to time. It is probably partly related to the fact that this site works on several mirror servers. Sometimes a single server or another probably gets. If you start to see lots of people post anything, but just a point, you will know that it is affecting more people. It is a common strategy to reveal hidden messages when a point of view of the site tells you it is updated the content on a thread, but you can not see.

  TT2

• El Capitan is not found Epson printer cable

  El Capitan using, I had my Epson unplugged for a week, finally plugged back in and restarted, has added a new driver from Apple, which seems to be the only choice and now he refuses to appear in preferences, printers and scanners. I tried to 'search' did not work. The printer is on, connected via USB on both ends, with a new driver, and it remains invisible to the computer. Ideas, or simple solutions that do not involve going to the Terminal and potchkeing around the code?

  If your Mac do not see your printer or have the software for it

  These steps can help if you tried to print from your Mac, but your printer does not appear in the pop-up menu printer, or your Mac displays a message that the software for your printer is not available.

  1. Make sure your printer is ready to print. Check for paper and other supplies and resolve any error lights or error messages. Check the printer documentation or contact the manufacturer if you need help with an error.
  2. If your printer is connected to the USB port of your Mac, unplug the printer.
  3. Your Mac software downloads for most printers automatically, is usually not necessary to install the software from the manufacturer of the printer. Always check the updates for you ensure that your Mac has the latest information on the printer.
  4. If your printer is not connected to your wired network, wireless networkor the USB port of your Mac, plug it back now.
  5. Open an item that you want to print, then choose print in the file menu.

  Get help to solve the problems of printer on your Mac - Apple Support

  and if it does not work

  Reset the printing on your Mac - Apple Support System

• "Setup cannot find not all hard disks" on Dell PERC 6/1 RAID controller-supported?

  Hi team - I have a Dell R710 (physical host) PE server that uses the Dell PERC RAID controller 6/1.  Windows Server 2008 x 64 is the host operating system.  VMW Server 2.02 installs and works very well, and I need to install W2K8 x 32 (guest) server configuration, but windows can't see the virtual disk with the same error "Setup cannot find not all hard disks", you get the installation on Windows XP Home edition- but the documentation does not say it's controller RAID is not taken in charge should be... any ideas?

  This is not a problem of the underlying RAID/hardware controller.

  Virtual MACHINE on VMware Server just to see the virtual hardware that you have configured when creating the virtual machine, or through the settings.

  Be sure to select the correct target OS when you create a virtual machine. This configures the disk controller HARD virtual appropriate, which should be supported on the OS installation media.

  If you have selected the right OS and still have problems, please post the vmx file.

  André