258 system error

Similar Questions

• TE2300 - fatal system error

  Hi all

  I am a newbie here, I get the blue screen on my computer (TE2300) error:

  Stop: c000021a {fatal system error}
  The process of Windows Subystems ended unexpectedly with status c0000005 (0x7c9106c3 0x0069f36c)

  Beginning physical memory dump
  Total physical memory dump
  contact you system administrator or technical support for further assistance group

  No idea what's going on, please help

  Hi Riann,

  Do you get this error message when you try to start your computer (Windows)?
  If so, you can start in safe mode?

  It is always difficult to say if bluescreens are software or hardware associated but first, you need to reinstall Windows if t, you can boot into safe mode.

• Satellite M30-106: System error at startup: resource conflict run the program installation or start-up?

  Hello, can someone help me please?
  When I start or restart my Toshiba Satellite SM30-106 laptop I get a system error RESOURCE CONFLICT Do You want to run the installation?

  I have 2 options [Run Setup] or [Boot]
  If I run [installation] I go to the blue Bios setup but can not see anything that can cause this error.
  If I select [boot boots} the system as usual.]
  How can I get my laptop start normally?
  I have no shared or added to any material. I ran the CD recovery Toshiba, no luck.
  concerning

  Richard, London SE6

  Y at - it an option to load the default settings of the BIOS on your laptop? If so, try it.

  Can't think right now that can generate this error unless you have recently
  had a new device that is STILL attached to a USB port (USB drive, printer, etc.)

  Concerning

  chain

  Update:
  I had a mistake of swearing to this post. I have found what Word does: "P E N" USB key so I replaced it with USB

• Equium P300-16 t - system error writing Configuration data

  Salvation message for the first time

  I have a Toshiba Equium P300-16 t and it has developed an error starting on the screen, it says

  System error writing Configuration data
  F1 - F2 CV - Bios settings

  When it appears that I can't get the option of recovery for work the bios settings seem to be completely in-accessible.

  This error appears just under the version number of the bios and the specifications of the RAM, just after the toshiba screen. The laptop is also a beep which I think is its length bios error code just two beeps very loud and even with a very short break inbetween

  On the page that appears after F1 (curriculum vitae) is pressed it shows just an another two options that are
  F2 - Setup F12 Multiboot Menu selection

  None of these options no matter what and the system is just idle on this screen.

  Obviously, without the bios menu there is not much I can do

  Really research help solve this problem as im not very clued up on the configurations of the system

  Oh and incase it allows... BIOS version - PhoenixBIOS 4.0 release 6.1

  Thanks in advance
  Kris

  Hi mate

  It would be interesting to know if the HARD drive is listed in the BIOS.
  Could you if you please check this?
  In the BIOS, you should see the HARD drive and HARD drive details
  If it is not visible, then that would mean that the HARD drive is faulty and therefore the operating system cannot be started.

  In this case, the HARD disk needs to be changed.

• Windows 7-Multiple system errors

  1. The chain of following events occurred
  2. Delete-PDF Viewer to use Revo uninstaller pro
  3. Download Nitro Reader - http://www.nitroreader.com/
  4. "Install drive Nitro-cannot install error"the could not access the Windows Installer service "
  5. File system error checker? Sfc/scannow = "Windows Resource Protection could not start the repair service".
  6. Error "Turn on Windows Defender", this program Service stopped (error Code: 0x800106ba)
  7. Restoration of the system of the error, "system restore doesn't seem to work properly on this system, etc..

  Apparently, a lot of programs W7 made.  I'm afraid that Windows Defender does not work and I'm not protected.  Windows Explorer 8 works, but Firefox does not work.

  Help

  Dave

  I solved my problem caused by point 1.  The registry changes during uninstallation of the program Revo Uninstall corrupted registy causing the problem.  The Revo program records the registy and allows you to reinstall it as it was before the uninstall.  After the reinstall all the programs work perfectly.

  Thank you

  Dave

• Compaq Presario CQ57: Need to get into the BIOS boot options received the disabled system error 59025057

  Need to enter boot BIOS options have system error disabled 59025057 also want to disable the password of the bios for the future

  @thatmomgamer

  Please enter:

  46983099

  Kind regards.

• HP ENVY 17-j005tx Notebook PC, AccelerometerSt.exe - open pop - start up of the system error

  Hello

  I use a HP ENVY 17-j005tx Notebook PC with the latest installed Windows 8.1.

  Whenever I start my computer, I get the following pop-up message:

  "AccelerometerSt.exe - system error - cannot start the program becaue mfc110u.dll is missing on your computer. Try reinstalling the program to fix this problem. »

  I don't know how to fix this? There are a lot of questionable research sites that offer downloads for these "missing files" but I'm sure that's not the solution.

  Could someone possibly offer me some advice of bette?

  Thank you in advance.

  Hello

  The missing dll is part of HP 3D DriveGuard - you can download and reinstall this software from the following link.

  http://ftp.HP.com/pub/SoftPaq/sp63501-64000/sp63786.exe

  Kind regards

  DP - K

• 1050 'system error' only - no code number

  About a 1050c more (an outsider? 1055 CM Plus - no hard drive and has A.02.05 RTL firmware DIMM.)  It has 128 MB of RAM.).  the printer is installed locally on a tcp/ip port.  and installed in the same way on other computers in the office.  They wanted not installed on the network at the time.
  
  customer sent a drawing page and the 'system error' 'contact HP representative' 2? rises. No number code error, only "system error" and that is all. I had him power cycle and must reload the paper and the print job proceeded.  I watched for about an hour in this forum, but nothing so far.  I'm just trying to be proactive, I saw the error once before, I think that, on the same plotter.
  
  I think I have seen that before on the same machine, but forget the circumstances.  I think the 1st time I seen it for some reason, I thought he came because I always had the bridge of HDD installed, so deleted but I don't know who is related, either.  Or with respect to the client, I cycled just power and it did not reappear.
  
  Thank you.
  
  Paul

  You can run the printer information page of the menu utilities and it should list errors. Also have you changed the process configuration in the printer to process in the computer to the default driver. Process in the computer change eliminates any possibility of running out of memory problems.

• Tecra 8100 system error when using Bank B

  Hello

  I get Bluscreens and system errors when you use Bank B. When you use Module1 in the Bank, everything is ok. When the same module as Bank A Bank (Bank A + B) b, I get errors.

  So, what would it be? What I have to 'turn on' the use of BANK B anywhere or not it looks like its defekt?

  Thanks for any help

  Hello

  Well, you must replace the motherboard if the memory bank has a defect. In this case, the only good way to connect with the service partner. They might give you detailed information.

  Good bye

• Satellite A660 - TosBtMng.exe - system error - Bluetooth does not

  Hello

  Not long bought my computer and just recently tried to connect my phone via blutooth.
  However when I try to use the bluetooyh I can't start. I just get the error message

  ' TosBtMng.exe - system error. The program cannot start because TosHdpAPI.dll is missing on your computer. Try reinstalling the program to fix the problem"

  I tried uninstalling BT stack and downloaded the latest version on the Toshiba site, but nothing has changed.
  Can anyone help?

  Thank you very much.

  The installation has successfully completed?
  Looks like something was not installed.

• Satellite A100 - unrecoverable system error and restart

  Without warning my Satellite A100 don't close but reboot, I removed the auto reboot, and the error that is displayed in the BSOD is:

  STOP: c000021a {fatal system error}
  The Windows Logon Process system process ended unexpectedly with status 0xc0000000 (0x00000000 0 x 0000000)

  in the event where Viewer does not appear anything on the error, I tried a system restore but it cannot exercise, in the event viewer this time it is written that he cannot run because the PC is not turned off regularly,
  How can I do?
  The BSOD appear in the last stop after the color screen when turned on the black screen just before the
  Turn off the power.

  your
  Fabio

  Hi flottero,

  It of always a little difficult to discuss these blue screens because many things could be the reason, but in most cases it s a hardware or driver problem.

  If system restore doesn't work, can you try to restore Windows recovery disk settings, please? After that, you get back factory settings and so you can identify a hardware problem or software.

  Check this box!

• Satellite A30: system32\config\system error message

  Hello

  I have a Satellite A30 and when I start it it displays the system32\config\system error message

  He also says I can try to repair it by starting the original windows using the installation CD installation program.

  Problem is that I don't have any CD or recovery discs that I bought the laptop on ebay 2 years ago

  While the options of do I have that I don't really want to spend the money, put it in repair... the credit crunch and all that!

  Thank you

  Hello

  Hmm I doubt that you can solve this problem without going through any system windows disk or recovery disk.
  It seems that the installed OS is messed up and you last chance would be a new installation of the OS on the MS Windows CD or Toshiba recovery disc.

  Good bye

• HP MINI 110 FATAL SYSTEM ERROR STOPPED. [redacted]. !!!

  HP MINI 110 LAPTOP FATAL SYSTEM ERROR STOPPED.

  [number of Series edited by Moderator]

  Please someone SOLVE THIS PROBLEM. I HAV NOT OPEN MY LAP FOR 3 months...

  Hello

  Try to enter: e9loq3f5ne (3rd character is a lowercase L)

  Kind regards

  DP - K

• C000021a error: {fatal system error} when starting laptop PC M30 series

  I get the following error when starting my laptop.

  "Stop: c00021a {fatal system error} the windows logon system process ended unexpectedly with status 0 x 00000080 (0x00000000 0x00000000).
  The system was stopped.

  I have the CD of restoration at the time of purchase. I have some data I need to recover. If someone knows the resolution of this problem, please let me know the procedure.

  Thanking you in advance.
  -YG

  Hello

  I found an interesting page. Please check all the solutions mentioned on this page. http://www.eggheadcafe.com/NG/Microsoft.public.WindowsXP.accessibility/post652591.asp

  Good luck!

• Satellite A350-12J said to insert the DVD + "this is a system error.

  I recently bought a toshiba Satellite A350-12J...
  The computer tells you to insert the DVD + this is a system error...

  Please insert the DVD - disks to perform backup of the recovery disks.
  I hope it is of some help, I am now almost bald of pulling my hair!

  Hello

  You are not able to boot the system? Or what?
  What happens if you press F8 immediately after the laptop was turned on?
  You then see the start menu?

  If you can access the advanced boot menu, then you could try using the option called last good known Configuration (Advanced).

  If this will not help and you will not be able to restart the laptop then choose fix my computer-> Toshiba HDD recovery and reinstall the OS using the Toshiba HDD recovery option.

  See you soon