2821 router support
Dear Sir.
Praposed connectivity for voice between neighborhoods General remote IP phones to analog phones is regarding the attached flowchart. Cisco 2821 routiters with IOS 12.2 are interconnected (v.35) line using rented between HQ FOR REMOTE SITES. To remote sites analog phones are connected to the FXS ports. To end HQ PABX with the required number of user liseces for IPPHONES is connected to the router via an ethernet switch. It is the installation of the network shown in the diagram is correct for connectivity you want between phones ip HQ for analog phone of BRANCH. What should be the requirement of configuration in the router for connectivity abive.
Please give me some examples
Thank you & best regards
Srinivas
Hello Srini,
your lab configuration is similar to what I guessed.
the IP PBX has an IP address on the same subnet IP to the lan from 2800 HQ interface.
You can run a routing protocol on the V.35 point - to - point link in order to advertise the subnet LAN of HQ.
In addition to what was already mentioned in my first post the use of QoS for a priority queue VoIP calls is recommended.
The part of QoS can be added later to the installation of laboratory.
Hope to help
Giuseppe
Tags: Cisco Network
Similar Questions
-
Problem starting the Cisco 2821 router
Hello world
I have cisco 2821 router. I am facing problem starting.
someone suggest me what is the problem.
Thanks in advance...
VERSION of the SOFTWARE system Bootstrap, Version 12.4 (13r) T, (fc1)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.The ECC memory initialization
.
C2821 platform of 262144 KB of main memory
Main memory is configured for 64-bit with ECC activeReadOnly initialized ROMMON
load complete, point of entry to the program: 0x8000f000, size: 0xcb80
load complete, point of entry to the program: 0x8000f000, size: 0xcb80load complete, point of entry to the program: 0x8000f000, size: 0x26bc2cc
Decompression of self-image: #.
################################################################################
################################################################################
################################################################################
################################################################################
################################################################# [OK]Smart init is enabled
Smart init is sizing iomem
MEMORY_REQ TYPE ID
0003E8 0X003DA000 C2821 Mainboard
1A 0X0025178C E3 0001AB
0X00263F50 VPN on board
0X000021B8 embedded USB
Swimming pools public buffer 0X002C29F0
Swimming pools public particle 0 X 00211000
TOTAL: 0X00D65284If all memory conditions above are
"UNKNOWN", you could use a non supported
configuration or there is a software problem and
the system may be compromised.
Rounded IOMEM to: 14 MB.
Using iomem of 5 percent. [14 mb / 256Mb]Legend restricted rights
Use, duplication, or disclosure by the Government is
subject to such restrictions as set out in paragraph
(c) Commercial - limited computer software
The rights to FAR clause 52.227 - 19 and subparagraph s
(c) (1) (ii) rights to technical and computer data
Clause of DFARS 252.227 - 7013 section software.Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706Cisco IOS software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4 T7 (9)
Version of the SOFTWARE (fc3)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Last updated Friday, January 10 08 16:35 by prod_rel_team
Image text-base: 0x400B1E74 database: 0x434A9AC0ERROR detected on Bus PCI1
Try REINSTALLING all the modules in the system
pci1_int_cause 0 x 00000240,
pci1_err_addr 0 x 00091009, pci0_err_cmd 0x0000000A
PCI Master Read parity error
Abort target PCIR0 = r1 = r2 FFFFFFFF FFFFFFFF = 0 r3 = 45 80000 r4 = 0
R5 = 303 r6 = 0 A7 = 1 = 0 = 100000 r9 r8
R10 = 0 r11 = 465E4369 r12 = 0 r13 = 465E436A r14 = 0
R15 = r16 r17 8 = 0 = C100 r18 = 0 r19 3400 101 =
R20 = r21 0 = 40096828 r22 = FFFFFFFF r23 = r24 FFFF00FF = 0
R25 = 469AAC64 r26 = 0 = 469AAC60 r28 = 0 = 469AAC5C r29, r27
R30 = 0 r31 = 469AAC58 r32 = r33 FFFFFFFF = r34 = FFFFFFFF FFFFFFFF
R35 = r36 = r37 = r38 = r39 FFFFFFFF FFFFFFFF FFFFFFFF FFFFFFFF = FFFFFFFF
R40 = FFFFFFFF = FFFFFFFF = FFFFFFFF = FFFFFFFF r44 r43 r42 r41 = FFFFFFFF
R45 = r46 = r47 = r48 FFFFFFFF FFFFFFFF FFFFFFFF = r49 0 = 469AACD0
R50 = 0 0 = 0 r53 r51 = r52 = 3040A 801 r54 = FFFFFFFF
R55, r56 = FFFFFFFF = FFFFFFFF r58 r57 A000F000 = = 0 = 465E4358 r59
R60 = r61 = r62 FFFFFFFF FFFFFFFF = r63 = 0 402E4B10
GENS = 3400 103 mdlo_hi = my 0 = 251 00
mdhi_hi = 0 = 0 badvaddr_hi = FFFFFFFF mdhi
BadVAddr = cause = epc_hi 0 = FFFFFFFF FFFFFFFF
EPC = 402E4B08 err_epc_hi = err_epc FFFFFFFF = FFFFFFFFERR-1-FATAL %: interruption of the fatal error, reload
err_stat = 0 x 0= Posts from Flushing (02: 37:51 UTC Wednesday, may 18, 2016) =.
Messages in queue:
02:37:51 UTC Wednesday, may 18, 2016: interrupt exception, signal CPU 22, PC = 0 x 0
--------------------------------------------------------------------
Software fault possible. On reccurence, you perceive
crashinfo, 'show tech' and contact Cisco Technical Support.
---------------------------------------------------------------------Trace =
$0: 00000000, AT: 00000000, v0: 00000000, v1: 00000000
A0: 00000000, a1: 00000000, a2: 00000000, a3: 00000000
T0: 00000000, t1: 00000000, t2: 00000000, t3: 00000000
T4: 00000000, t5: 00000000, t6: 00000000, t7: 00000000
s0: 00000000, s1: 00000000, s2: 00000000, s3: 00000000
S4: 00000000, s5: 00000000, s6: 00000000, s7: 00000000
T8: 00000000, t9: 00000000, k0: 00000000, k1: 00000000
GP: 00000000, sp: 00000000, s8: 00000000, ra: 00000000
EPC: 00000000, ErrorEPC: 00000000, GENS: 00000000
MY: 00000000, MDHI: 00000000, BadVaddr: 00000000
CacheErr: 00000000, DErrAddr0: 00000000, DErrAddr1: 00000000
DATA_START: 0X434A9AC0
Cause 00000000 (Code 0 x 0): Exception of interruptionWriting crashinfo in flash: crashinfo_20160518-023752
No reboot to warm storage
System received a system error *.
signal = 0 x 16, code = 0x0, context = 0 x 46905718
PC = 0x40096d7c, Cause = 0 x 20, State Reg = 0 x 34008002Software Cisco IOS, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4 (9)T7
Version of the SOFTWARE (fc3)OK, the router is running on a train of "T".
ERROR detected on Bus PCI1
Try REINSTALLING all the modules in the system
pci1_int_cause 0 x 00000240,
pci1_err_addr 0 x 00091009, pci0_err_cmd 0x0000000A
PCI Master Read parity error
Abort target PCIRemove any all NM/NME or WIC/HWIC cards and restart again. If the router is able to start properly, upgrade the router to a higher version. DO NOT use another "T" train if it is needed. Use instead a train of "M".
-
What linksys Modem router supports WOL or DHCP reservation?
Hi all
What linksys Modem router supports WOL or DHCP reservation?
Thank you Alex
Hello. I checked the site made up of Cisco and up to 3000 X & X 2000 has the DHCP reservation and like many Eseries routers they have. Just try to check homesupport.cisco.com.
-
2821 router to access T1 on LAN
I'll put up a Cisco router for a T1 line for the first time and I hit a barrier. The router, a 2821 with WIC-1DSU-T1-V2 is online (all statuses are rising and I can ping outside sites). However, a laptop computer connected to the router can not access the Internet outside.
My router (sterilized) static IP from the ISP is 10.0.0.222. It is on the 10.0.0.220/30 network, with a broadcast address of 10.0.0.223/30. The ISP gateway is 10.0.0.221
I have the Gigabit Ethernet port game with an IP address of 192.168.1.1/24
Here is the configuration:
!
version 12.4
service configuration
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
No dhcp service
!
router host name
!
boot-start-marker
boot-end-marker
!
enable secret 5 XXXXXXXX
activate the password XXXXXX
!
No aaa new-model
no ip Routing
!
!
no ip cef
!
!
name-server IP 10.0.0.3
name-server IP 10.0.0.4
!
!
!
!
!
interface GigabitEthernet0/0
no ip address
no ip route cache
Shutdown
automatic duplex
automatic speed
No cdp enable
!
interface GigabitEthernet0/1
IP 192.168.1.1 255.255.255.0
no ip route cache
automatic duplex
automatic speed
No cdp enable
No mop enabled
!
interface Serial0/0/0
IP 10.0.0.222 255.255.255.252
encapsulation ppp
no ip route cache
no fair queue
!
default IP gateway - 10.0.0.221
IP forward-Protocol ND
!
IP http server
!
!
control plan
!
!
Line con 0
exec-timeout 0 0
line to 0
line vty 0 4
password XXXXXX
opening of session
!
Scheduler allocate 20000 1000
No extensive process CPU
No pork process autoprofile cpu
!
endSince the router command line I can ping 10.0.0.221 (Gateway ISP) as well as external IP addresses. Domain names resolve correctly and can be crazy. I ping the router of my regular Internet connection.
However, when I join a laptop the GigabitEthernet0/1 (static IP address of the laptop is 192.168.1.2) I can't seem to the outside network. I can ping the map T1 and Ethernet card address, but not the ISP (10.0.0.221) gateway or all other external addresses.
I tried to adjust laptop, gateway 192.168.1.1 and 10.0.0.222. Set to 10.0.0.221 gives an error "network unreachable".
I am new to Cisco routers, so I guess it's something simple, maybe an IP need rule of routing or something?
In summary: the router is online on T1, can ping and ping, but laptop connected to the ethernet router cannot be accessed outside the network.
Thanks for any help.
Hello
I guess the problem is that your ISP does not know how to route the packets back to your 192.168.1.0 subnet. If you ping the router with the address of the source of your inside interface it will confirm if this is the case or not.
You can run a dynamic routing with your ISP Protocol which I guess is not the solution preferred the complexity. You can ask the ISP adds a route to your network, but again once I guess that's not an option.
The most appropriate solution would be to run NAT Network Address Translation on your serial interface and use overhead NAT to translate entire your network to your unique WAN address.
Hope that helps.
http://www.Cisco.com/c/en/us/support/docs/IP/network-address-translation...
-
model orientation of 2821 router please?
I need to upgrade the ROMMON to correct a problem of vulnerability (PSIRT: 62573_FN_62573_RouterAS535) and I try to load the file recommended ' C2800NM_RM2.srec.124 - 13r.T5 ' in our 2821 routers... can someone tell me what directory to put in it please? I tried everything I can think of without success. Just, he's missing, use my TFTP try again and then abandons the session. Thank you! Best regards, Michael
Hi Michael,
1. instead of upgrade the ROMmon to 12.4 (13r) T5, please consider upgrading to version 12.4 T11 (13r) that this version is the ability to allow the router to boot via USB.
2. can you have physical access to the router? The router has two USB ports, you can put the IOS in a USB key (as it has supported and correctly formatted).
To apply the upgrade ROMmon, the command is:
TFTP: upgrade the rom t fileftp: / //filename
USB: upgrade the rom usbflash0 file / 1:filename
In all cases, you will be asked a yes/no question, and if you press on 'y', the router will upgrade the ROMmon and recharge.
-
More time capsules (or any Apple router) support VDSL2?
I change ISPS to fiber high speed (PlusNet, to the United Kingdom) and want to use my time rather than their router Capsule. They say that any router I use must take over VDSL2.
The older is (1 to 2012) Time Capsule - or do any of the current versions of the Apple routers - support it?
The older is (1 to 2012) Time Capsule - or do any of the current versions of the Apple routers - support it?
Sorry, but no. Apple routers have a modem on board, so you will always need to use a modem with a router from Apple with any type of DSL service.
-
Hi all
I have 5 wireless devices must connect to the router.
I want to divide it into 2 groups:
That is to say, 1, device A, B, C, group 2, device D, E.
I would like two groups cannot communicate with each other.
I've heard, it can be done by VLAN, is e2500 can adapt to what I need?
What about EA3500 and EA4500?
I use G wireless, is what it means that ea4500 is out of choice even if it supports VLAN?
Thank you all!
Evil
Thanks for the clarification for the OP
FWIW
is this an alternative to routers that do not support of VLAN, to do what you want
-
What SMB router support services to wide band to 60 Mbps download?
Hello, we are trying to determine on what router in the SMB line would support speeds above over the WAN?
The fact sheets provide info flow NAT, but I don't know if it's enough to make a decision.
RV180 series seems to offer another NAT flow in 800Mbps. Services that NAT is not necessary.
The RV042 also seems to be able to support this speed, but overall, it is not really clear if the RV will work or not.
Help, please?
Thank you!!
Hello
"NAT flow" you see in the technical data is the data of the unit - NAT of 800mbps throughput will certainly support a 60 Mbps connection. I would go with the RV180 on the 042 because of gigiabit ports, on 180. Is the RV042 router double wan, that the RV180 does not support dual wan. The flow of the RV042 nat is only 100 Mbit/s. If you need dual wan, I would go with the RV042G which has a flow 800mbps and gigabit ports.
Just for reference, I've always found the comments on to very useful smallnetbuilder.com.
Hope that helps.
Best,
David
-
My router supports CBAC?
It seems that some router IOS versions 12.2 or better to support CBAC and others do not. Is there something that I can look in the NVA SH or SH RUN where I can tell if the operating system supports the IOS Firewall Feature Set?
OK, let's try again. I know it can be confusing. In 12.1 images and earlier versions (I think), you can identify an IOS image that has the CBAC (or IOS Firewall because it sometimes referred to as) features enabled by finding an 'o' in the name of the image file. Beginning in paragraph 12.2 and later versions, you can identify it with a 'o3' in the name of the image file. They both mean the same thing. The image I posted wasn't c1600-osy56i-l. 121 - 11.bin. Note the "o" in the name of the image after the flag of the platform.
Now, to the FW part. In the center of software for different IOS images, you will see various lengthy game descriptions. The active CBAC feature sets will have FW in the description. For example, http://www.cisco.com/cgi-bin/Software/Iosplanner/Planner-tool/iosplanner.cgi?get_crypto=&data_from=&hardware_name=1601-1604&software_name=&release_name=12.2.19a&majorRel=12.2&state=:HW:RL & type = limited % 20Deployment you can see the following: IP/FW MORE IPSEC 56
Note the above FW. This indicates that this link will take you to an image which has features of firewall enabled and has also a 'o' or 'o3' in the name of the image file.
Do not confuse the version "bootstrap" in the code with the version of the code that is running on the router. You can go back and review the output. This should be the code of 12.1 (11) for a 1600.
CBAC has been added to IOS in 12.0 (5) T and later in 12.1 mainline as well. All versions should subsequently have active CBAC IF a 'o' or 'o3' exists in the name of the image file.
I really hope this helps.
Scott
-
IPSEC tunnel and Routing Support protocols
Hello world
I read that IPSEC does not support routing with VPN's Site to the other protocols because both are Layer4.
This means that if Site A must reach the B Site over a WAN link, we use static IP on the Site A and Site B router?
In my lab at home I config Site to Site VPN systems and they work correctly using OSPF does that mean that IPSEC supports the routing protocol?
IF someone can explain this please?
OSPF config one side
router ospf 1
3.4.4.4 router ID
Log-adjacency-changes
area 10-link virtual 10.4.4.1
passive-interface Vlan10
passive-interface Vlan20
3.4.4.4 to network 0.0.0.0 area 0
network 192.168.4.0 0.0.0.255 area 10
network 192.168.5.0 0.0.0.255 area 0
network 192.168.10.0 0.0.0.255 area 0
network 192.168.20.0 0.0.0.255 area 0
network 192.168.30.0 0.0.0.255 area 0
network 192.168.98.0 0.0.0.255 area 0
network 192.168.99.0 0.0.0.255 area 0
3550SMIA #sh ip route
Code: C - connected, S - static, mobile R - RIP, M-, B - BGP
D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone
N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2
E1 - OSPF external type 1, E2 - external OSPF of type 2
i - IS - Su - summary IS, L1 - IS - IS level 1, L2 - IS level - 2
-IS inter area, * - candidate failure, U - static route by user
o - ODR, P - periodic downloaded route static
Gateway of last resort is 192.168.5.3 to network 0.0.0.0
192.168.12.0/24 [13/110] through 192.168.5.3, 3d17h, FastEthernet0/11
100.0.0.0/32 is divided into subnets, subnets 1
O 100.100.100.100 [110/3] through 192.168.5.3, 3d17h, FastEthernet0/11
3.0.0.0/8 is variably divided into subnets, 2 subnets, 2 masks
O 3.3.3.3/32 [110/2] via 192.168.5.3, 3d17h, FastEthernet0/11
C 3.4.4.0/24 is directly connected, Loopback0
C 192.168.30.0/24 is directly connected, Vlan30
64.0.0.0/32 is divided into subnets, subnets 1
O E2 64.59.135.150 [110/300] through 192.168.5.3, 1d09h, FastEthernet0/11
4.0.0.0/32 is divided into subnets, subnets 1
O 4.4.4.4 [110/2] via 192.168.5.3, 3d17h, FastEthernet0/11
C 192.168.10.0/24 is directly connected, Vlan10
172.31.0.0/24 is divided into subnets, 4 subnets
O E2 172.31.3.0 [110/300] through 192.168.5.3, 3d17h, FastEthernet0/11
O E2 172.31.2.0 [110/300] through 192.168.5.3, 3d17h, FastEthernet0/11
O E2 172.31.1.0 [110/300] through 192.168.5.3, 3d17h, FastEthernet0/11
O E2 172.31.0.0 [110/300] through 192.168.5.3, 3d17h, FastEthernet0/11
O 192.168.11.0/24 [110/3] through 192.168.5.3, 3d17h, FastEthernet0/11
O 192.168.98.0/24 [110/2] via 192.168.99.1, 3d17h, FastEthernet0/8
C 192.168.99.0/24 is directly connected, FastEthernet0/8
192.168.20.0/24 C is directly connected, Vlan20
192.168.5.0/31 is divided into subnets, subnets 1
C 192.168.5.2 is directly connected, FastEthernet0/11
C 10.0.0.0/8 is directly connected, Tunnel0
192.168.6.0/31 is divided into subnets, subnets 1
O 192.168.6.2 [110/2] via 192.168.5.3, 3d17h, FastEthernet0/11
192.168.1.0/24 [13/110] through 192.168.5.3, 3d17h, FastEthernet0/11
O * E2 0.0.0.0/0 [110/1] via 192.168.5.3, 1d09h, FastEthernet0/11
B side Config
Side A
router ospf 1
Log-adjacency-changes
network 192.168.97.0 0.0.0.255 area 0
network 192.168.98.0 0.0.0.255 area 0
network 192.168.99.0 0.0.0.255 area 0
1811w # sh ip route
Code: C - connected, S - static, mobile R - RIP, M-, B - BGP
D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone
N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2
E1 - OSPF external type 1, E2 - external OSPF of type 2
i - IS - Su - summary IS, L1 - IS - IS level 1, L2 - IS level - 2
-IS inter area, * - candidate failure, U - static route by user
o - ODR, P - periodic downloaded route static
Gateway of last resort is 192.168.99.2 to network 0.0.0.0
192.168.12.0/24 [110/14] through 192.168.99.2, 3d17h, FastEthernet0
100.0.0.0/32 is divided into subnets, subnets 1
O 100.100.100.100 [110/4] through 192.168.99.2, 3d17h, FastEthernet0
3.0.0.0/32 is divided into subnets, 2 subnets
O 3.3.3.3 [110/3] through 192.168.99.2, 3d17h, FastEthernet0
O 3.4.4.4 [110/2] via 192.168.99.2, 3d17h, FastEthernet0
O 192.168.30.0/24 [110/2] via 192.168.99.2, 3d17h, FastEthernet0
64.0.0.0/32 is divided into subnets, subnets 1
O E2 64.59.135.150 [110/300] through 192.168.99.2, 1d09h, FastEthernet0
4.0.0.0/32 is divided into subnets, subnets 1
O 4.4.4.4 [110/3] through 192.168.99.2, 3d17h, FastEthernet0
O 192.168.10.0/24 [110/2] via 192.168.99.2, 3d17h, FastEthernet0
172.31.0.0/24 is divided into subnets, 4 subnets
O E2 172.31.3.0 [110/300] through 192.168.99.2, 3d17h, FastEthernet0
O E2 172.31.2.0 [110/300] through 192.168.99.2, 3d17h, FastEthernet0
O E2 172.31.1.0 [110/300] through 192.168.99.2, 3d17h, FastEthernet0
O E2 172.31.0.0 [110/300] through 192.168.99.2, 3d17h, FastEthernet0
O 192.168.11.0/24 [110/4] through 192.168.99.2, 3d17h, FastEthernet0
C 192.168.98.0/24 is directly connected, BVI98
C 192.168.99.0/24 is directly connected, FastEthernet0
O 192.168.20.0/24 [110/2] via 192.168.99.2, 3d17h, FastEthernet0
192.168.5.0/31 is divided into subnets, subnets 1
O 192.168.5.2 [110/2] via 192.168.99.2, 3d17h, FastEthernet0
192.168.6.0/31 is divided into subnets, subnets 1
O 192.168.6.2 [110/3] through 192.168.99.2, 3d17h, FastEthernet0
192.168.1.0/24 [110/14] through 192.168.99.2, 3d17h, FastEthernet0
O * E2 0.0.0.0/0 [110/1] via 192.168.99.2, 1d09h, FastEthernet0
Thank you
Mahesh
Mahesh.
Indeed, solution based purely crypto-card are not compatible with a routing protocol. Crypto card however is the legacy config we support on IOS. The best practice is to use the protection of tunnel. Any routing protocol would work then.
for example
https://learningnetwork.Cisco.com/docs/doc-2457
It's the best solution we currenty have
-
Cisco 892 NAT or routing support for VoIP
I have some experience with Cisco switches, but not with routers. I'm trying to connect to a network of small intrenal at the port of FastEthernet8 and the WAN connected to Gigabit 0. I was able to configure DHCP for the internal network, but have been several days trying to find a way so that it can route all traffic through the WAN interface. I enclose below my current setup. Any help would be greatly appeciated.
Current configuration: 1542 bytes
!
! Last modification of the configuration to 00:15:51 UTC Sunday, August 24, 2014
!
version 15.0
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname sgivoip
!
boot-start-marker
boot-end-marker
!!
No aaa new-model
!
!
!
!
!
IP source-route
!
!
DHCP excluded-address IP 192.168.11.1 192.168.11.30
!
IP dhcp pool insideDHCP
network 192.168.11.0 255.255.255.0
router by default - 192.168.54.202
DNS-server 167.206.112.138 167.206.7.4
!
!
IP cef
No ipv6 cef
!
!
Authenticated MultiLink bundle-name Panel
license udi pid CISCO892-K9 sn FGL1710231R
!
!
!
!
!
!
!
!
!
!
!
interface BRI0
no ip address
encapsulation hdlc
Shutdown
Multidrop ISDN endpoint
ISDN point - to point-setup
!
!
interface FastEthernet0
!
!
interface FastEthernet1
!
!
interface FastEthernet2
Shutdown
!
!
interface FastEthernet3
Shutdown
!
!
interface FastEthernet4
Shutdown
!
!
interface FastEthernet5
Shutdown
!
!
FastEthernet6 interface
Shutdown
!
!
interface FastEthernet7
Shutdown
!
!
interface FastEthernet8
192.168.11.1 IP address 255.255.255.0
full duplex
automatic speed
!
!
interface GigabitEthernet0
DHCP IP address
automatic duplex
automatic speed
!
!
interface Vlan1
no ip address
Shutdown
!
!
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
!
!
Dialer-list 1 ip protocol allow
!
!
!
!
!
!
control plan
!
!
!
Line con 0
line to 0
line vty 0 4
password *.
opening of session
!
max-task-time 5000 Planner
endI'm trying to figure out what makes the default entry of the 192.168.54.202 router in your DHCP pool? It usually comes to 192.168.11.1 or whatever you want your router to be. You need to add the following commands:
interface F8
IP nat inside
interface G0
NAT outside IP
IP access-list standard NAT
permit 192.168.11.0 0.0.0.255IP nat inside source list NAT interface G0 overload
That should do it. If you have any other questions, I would recommend turning off your modem cable for a few minutes and then turn power on and then turn your router. To see if you have received an IP address, you can run a show ip interface brief and next to G0, you should see an external IP address.
-
Hello
Can RV325 switch router supports to create 2 VIRTUAL LAN segments? The default route is a WAN using PPPoE port. The segment still used MODEM 3 G / 4G? Thank you!
Hello
My name is Patrick and I'm a developer eSupport with the Cisco Small Business support community. The RV325 can support up to 14 VLAN configurable separately. To find out how to add and modify VLANs on your device, I highly recommend that consult you this document in the Base of knowledge about belonging to a VLAN on the RV320 and RV325 VPN routers.
http://sbkb.Cisco.com/CiscoSB/UKP.aspx?login=1&PID=2&app=search&VW=1&articleid=4142
I hope this information is useful for you. Please reply back if you have other questions or concerns.
Best,
Patrick Ayers
-
router to router 2821 encryption
How to secure this scenerio?
(1) site A has a 2821 router and an IP connection to the site C. 2821 on another organizations IP network.
(2) site B has a router 2821 with an MPLS connection at the site of the C-2821.
It's pretty easy to connect and get plain text connections and tunnels WILL work, but I'm leaving my network open to other agencies or MPLS service provider.
I think little flavor of encryption between routers with tunnels GRE routes real traffic.
Thank you in advance for recommendations and examples of config.
Hi Tod,
You can deploy a separate acl on the physical interface, which allows only the tunnel itself (udp/500 and esp). The ACL in the VTI would control the traffic through the tunnel.
Rgds,
MiKa
-
What router chassis support SM-VAM2 +.
Hello!
I work for a non-profit organization and a donor gave us a generous donation of Cisco equipment. One of the elements is a SM-VAM2 +. We tried it in a chassis of 7206VXR with an NPE - G2 running 12.4 (24) T6 and router guard barking that the VAM2 SM + don't is not supported in the chassis. We have done research on the web site of Cisco and Google and there is no information about the SM-VAM2 + at all (all references are on the SA - VAM2 +).
The question is whether the SM-VAM2 + is supported on the 7206VXR with another version of IOS or what router supports the SM-VAM2 +?
Thank you very much!
I found this reference. Table 1 it says IOS 12.3(6a) or (6f) on the 7204, 7206 (NOT the model VXR) or 7301 should be compatible.
It looks like a pretty niche product which cannot have any practical use in your infrastructure.
-
We support the following formats URLS
< Store name > /store/ / s - < the base id > -
Ex: / store/chicago-store/s-1234.
It seems that the standard router supports following
/ store/s - < the base id > -
Ex: / store/s-1234.
Please advice.
When you use the JET router, there is no limit on how many 'segment' of the URL can be supported.
Each segment is managed by a router in the child, so for a URL as /store/
s - , "store name" is a child of the root (store) router, and "store" is a child of "store name" router Regarding SEO, JET does not provide any special support because it's something that you'd install server-side. Since there is no 'real' to the URL /store/
s - resources, you need to add some server-side code to return the base URL of initial false URLS generated by the router. This can be done using a simple rule for a rewrite, as mode_rewrite module for Apache HTTP server engine or a rewrite as UrlRewriteFilter for servlets filter. For an example of a filter of rewriting, look at http://jet.us.oracle.com/1.2.0/uiComponents-router-child.htmland click on the "Demo button to launch with adapter for URL path.
Maybe you are looking for
-
I know this question has been posted before, but I have still questions gain some applications on the android marketplace, because apps claim to not be compatible, even if I know they are. I tried to contact the app publishers to tell them to update
-
Lenovo L420 restarts while gaming
Hello! I want to say that my lenovo TP l420 restart game while... Basically whenever my system its normal temperature boot is around 60-70 degrees. & When I start a game it affects 90-100 I tried lenovo care system in which it started testing parts l
-
remove the domain to a domain computer users group
I have installed a computer in the field and that you wanted everyone to sign on the computer. Our policy has changed and now we only want one user to be able to log on to the machine side comes from the admin I've added to the domain to this machine
-
my system does not allow me to type in my password
my system does not allow me to type in my password
-
registration for Vista, the user is locked
When I log on to windows vista, it shows locked user. How can I unlock it? Zeaus