Support of router RV325

Similar Questions

• The SG300 - ACL support intervlan routing

  I have Setup SG300 - 52p mode switch layer 3.

  I have 3 VLAN (10,20,30) and the affected ports to each vlan.

  Each host can ping its own gateway (according to the VLAN).

  I want to enable some of the traffic of a vlan to a specific host (server) on a different VLAN. I try with ACL, but no can do.

  Can someone help me how to do this?

  Thank you very much.

  Hey Ruy,

  My isa very restrictive ACL.

  Restrict_FTP extended IP access list

  permit ip 192.168.10.0 0.0.0.255 192.168.20.10 0.0.0.0

  output

  It allows only the 192.168.10.0 network to get host 192.168.20.10 IP host.

  There is also perhaps (in red);

  Restrict_FTP extended IP access list

  permit ip 192.168.10.0 0.0.0.255 192.168.20.10 0.0.0.0

  deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255

  allow a full

  output

  I must confess that I prefer to use the GUI to produce my ACEs.  The table he creates shows how the ACL will work. and especially in what order.

  • The switch through ACEs in order from top to bottom as seen in the GUI.
  • The ACL that is attached to an interface, boss of matching incoming packages (coming into the switch).
  • ACE entries use reverse masking can be confusing.  Perhaps the following tehnote may be useful for understanding the inverse of masking;

  http://www.Cisco.com/en/us/products/sw/secursw/ps1018/products_tech_note09186a00800a5b9a.shtml

  What about Dave

• Supported on the Cisco RV042 router settings

  Hello

  Anyone know if these settings are supported on router CiscoRV042

  shared secret - authentication-

  -AES-256 / SHA1 encryption

  -IKE: Diffie-Hellman (Group 2)

  -Phase 1 IKE every 1440 minutes.

  -The phase 2 (IPsec) all 3600 sec (every hour) of IKE

  Thank you.

  These are all very standard parts of IPSEC.

  See page 45 of the

  http://www.Cisco.com/en/us/docs/routers/CSBR/RV042/Admin/Guide/RV042_V10_UG_C-Web.PDF

  Copied here

  IPSec configuration

  So that any encryption occur, both ends of a

  VPN tunnel must agree on the encryption methods,

  decryption and authentication. This is done by sharing

  a key for the encryption code. Key management, the

  default mode is IKE with pre-shared key.

  Overlay Mode Select IKE with pre-shared key or manual.

  Both ends of a VPN tunnel must use the same mode of

  key management. After selecting the mode, the

  settings available on this screen may change depending

  on the selection you have made. Follow the instructions

  for the mode you want to use. (Manual mode is available

  for VPN tunnels only, no VPN group.)

  IKE with preshared key

  IKE is used to negotiate Internet Key Exchange Protocol

  for Security Association (SA) key material. IKE use it

  Pre-shared key for authentication to the remote peer of IKE.

  The phase 1 DH group Phase 1 is used to create the SA. DH

  (Diffie-Hellman) is a key exchange protocol used for

  Phase 1 of the authentication before establishing process

  pre-shared keys. There are three groups of different premium

  length of the key. Group 1 is 768 bits, and group 2 is 1024 bits.

  Group 5 is 1 536 bits. If the network speed is preferred, select

  Group 1. If it is better to network security, select group 5.

  The phase 1 encryption select an encryption method: SOME

  (56-bit), 3DES (168-bit), AES-128 (128-bit), AES-192 (192-

  ILO) or AES-256 (256-bit). The method determines the

  length of the key used to encrypt or decrypt ESP packets

  AES - 256 is recommended because it is the safest.

  Make sure that both ends of the VPN tunnel using the same

  encryption method.

  The phase 1 authentication select a method of

  authentication, MD5 or SHA. The authentication method

  determines how the ESP packets are validated. MD5 is

  a one-way hash algorithm that produces a 128-bit

  Digest. SHA is a one-way hashing algorithm which produces

  a 160-bit digest. SHA is recommended because it is more

  Fix. Make sure that both ends of the VPN tunnels using the

  same authentication method.

  Phase 1 life time sets the duration of a VPN

  tunnel is active in Phase 1. The default is 28800

  seconds.

  Perfect Forward Secrecy if the perfect forward secrecy

  (PFS) is enabled, the IKE Phase 2 negotiation will be

  generate new key material for encryption of IP traffic and

  authentication, then pirates using brute force to break

  encryption keys will not be able to obtain future IPSec

  keys.

  Phase 2 DH group if the functionality of perfect forward secrecy

  is disabled, then no new key will be generated, so you don't have

  no need to adjust the Phase 2 DH group (the key for Phase 2

  will be the key in Phase 1).

  There are three groups of different main key lengths.

  Group 1 is 768 bits, and group 2 is 1024 bits. Group 5 is

  1 536 bits. If the network speed is preferred, select group 1.

  If it is better to network security, select group 5. You do

  no need to use the same group of DH that you used for

  Phase 1.

  Encryption of the phase 2 Phase 2 is used to create an or

  several IPSec security associations, which are then used to key IPSec sessions.

  Select an encryption method: NULL, (56-bit), 3DES

  (168 bit), AES-128 (128-bit), AES-192 (192-bit) or AES-

  256 (256-bit). It determines the length of the key used to

  encrypt or decrypt packets ESP. AES-256 is recommended

  because it is the safest. Both ends of the VPN tunnel

  must use the same encryption of Phase 2 setting.

  The phase 2 authentication select a method of

  authentication, NULL, MD5 or SHA. Authentication

  method determines how the ESP packets are validated.

  MD5 is a one-way hash algorithm that produces a

  Digest of 128 bits. SHA is a one-way hashing algorithm that

  produces a 160-bit "Digest". SHA is recommended because

  It's safer. Both ends of the VPN tunnel must use

  the same Phase 2 authentication setting.

  Phase 2 HIS life time sets the duration of a VPN

  tunnel is active in Phase 2. The default value is 3600 seconds.

  Pre-shared key that specifies the pre-shared key used

  to authenticate the remote peer of IKE. Enter a key of

  keyboard and hexadecimal characters, for example, [email protected]/ * /.

  or 4d795f40313233. This field allows a maximum of 30

  characters and hexadecimal values. The two ends of the

  the VPN tunnel must use the same pre-shared key. It's

  We recommend that you change the pre-shared

  Key periodically in order to maximize the VPN security.

• IPSEC tunnel and Routing Support protocols

  Hello world

  I read that IPSEC does not support routing with VPN's Site to the other protocols because both are Layer4.

  This means that if Site A must reach the B Site over a WAN link, we use static IP on the Site A and Site B router?

  In my lab at home I config Site to Site VPN systems and they work correctly using OSPF does that mean that IPSEC supports the routing protocol?

  IF someone can explain this please?

  OSPF config one side

  router ospf 1

  3.4.4.4 router ID

  Log-adjacency-changes

  area 10-link virtual 10.4.4.1

  passive-interface Vlan10

  passive-interface Vlan20

  3.4.4.4 to network 0.0.0.0 area 0

  network 192.168.4.0 0.0.0.255 area 10

  network 192.168.5.0 0.0.0.255 area 0

  network 192.168.10.0 0.0.0.255 area 0

  network 192.168.20.0 0.0.0.255 area 0

  network 192.168.30.0 0.0.0.255 area 0

  network 192.168.98.0 0.0.0.255 area 0

  network 192.168.99.0 0.0.0.255 area 0

  3550SMIA #sh ip route

  Code: C - connected, S - static, mobile R - RIP, M-, B - BGP

  D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone

  N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2

  E1 - OSPF external type 1, E2 - external OSPF of type 2

  i - IS - Su - summary IS, L1 - IS - IS level 1, L2 - IS level - 2

  -IS inter area, * - candidate failure, U - static route by user

  o - ODR, P - periodic downloaded route static

  Gateway of last resort is 192.168.5.3 to network 0.0.0.0

  192.168.12.0/24 [13/110] through 192.168.5.3, 3d17h, FastEthernet0/11

  100.0.0.0/32 is divided into subnets, subnets 1

  O 100.100.100.100 [110/3] through 192.168.5.3, 3d17h, FastEthernet0/11

  3.0.0.0/8 is variably divided into subnets, 2 subnets, 2 masks

  O 3.3.3.3/32 [110/2] via 192.168.5.3, 3d17h, FastEthernet0/11

  C 3.4.4.0/24 is directly connected, Loopback0

  C 192.168.30.0/24 is directly connected, Vlan30

  64.0.0.0/32 is divided into subnets, subnets 1

  O E2 64.59.135.150 [110/300] through 192.168.5.3, 1d09h, FastEthernet0/11

  4.0.0.0/32 is divided into subnets, subnets 1

  O 4.4.4.4 [110/2] via 192.168.5.3, 3d17h, FastEthernet0/11

  C 192.168.10.0/24 is directly connected, Vlan10

  172.31.0.0/24 is divided into subnets, 4 subnets

  O E2 172.31.3.0 [110/300] through 192.168.5.3, 3d17h, FastEthernet0/11

  O E2 172.31.2.0 [110/300] through 192.168.5.3, 3d17h, FastEthernet0/11

  O E2 172.31.1.0 [110/300] through 192.168.5.3, 3d17h, FastEthernet0/11

  O E2 172.31.0.0 [110/300] through 192.168.5.3, 3d17h, FastEthernet0/11

  O 192.168.11.0/24 [110/3] through 192.168.5.3, 3d17h, FastEthernet0/11

  O 192.168.98.0/24 [110/2] via 192.168.99.1, 3d17h, FastEthernet0/8

  C 192.168.99.0/24 is directly connected, FastEthernet0/8

  192.168.20.0/24 C is directly connected, Vlan20

  192.168.5.0/31 is divided into subnets, subnets 1

  C 192.168.5.2 is directly connected, FastEthernet0/11

  C 10.0.0.0/8 is directly connected, Tunnel0

  192.168.6.0/31 is divided into subnets, subnets 1

  O 192.168.6.2 [110/2] via 192.168.5.3, 3d17h, FastEthernet0/11

  192.168.1.0/24 [13/110] through 192.168.5.3, 3d17h, FastEthernet0/11

  O * E2 0.0.0.0/0 [110/1] via 192.168.5.3, 1d09h, FastEthernet0/11

  B side Config

  Side A

  router ospf 1

  Log-adjacency-changes

  network 192.168.97.0 0.0.0.255 area 0

  network 192.168.98.0 0.0.0.255 area 0

  network 192.168.99.0 0.0.0.255 area 0

  1811w # sh ip route

  Code: C - connected, S - static, mobile R - RIP, M-, B - BGP

  D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone

  N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2

  E1 - OSPF external type 1, E2 - external OSPF of type 2

  i - IS - Su - summary IS, L1 - IS - IS level 1, L2 - IS level - 2

  -IS inter area, * - candidate failure, U - static route by user

  o - ODR, P - periodic downloaded route static

  Gateway of last resort is 192.168.99.2 to network 0.0.0.0

  192.168.12.0/24 [110/14] through 192.168.99.2, 3d17h, FastEthernet0

  100.0.0.0/32 is divided into subnets, subnets 1

  O 100.100.100.100 [110/4] through 192.168.99.2, 3d17h, FastEthernet0

  3.0.0.0/32 is divided into subnets, 2 subnets

  O 3.3.3.3 [110/3] through 192.168.99.2, 3d17h, FastEthernet0

  O 3.4.4.4 [110/2] via 192.168.99.2, 3d17h, FastEthernet0

  O 192.168.30.0/24 [110/2] via 192.168.99.2, 3d17h, FastEthernet0

  64.0.0.0/32 is divided into subnets, subnets 1

  O E2 64.59.135.150 [110/300] through 192.168.99.2, 1d09h, FastEthernet0

  4.0.0.0/32 is divided into subnets, subnets 1

  O 4.4.4.4 [110/3] through 192.168.99.2, 3d17h, FastEthernet0

  O 192.168.10.0/24 [110/2] via 192.168.99.2, 3d17h, FastEthernet0

  172.31.0.0/24 is divided into subnets, 4 subnets

  O E2 172.31.3.0 [110/300] through 192.168.99.2, 3d17h, FastEthernet0

  O E2 172.31.2.0 [110/300] through 192.168.99.2, 3d17h, FastEthernet0

  O E2 172.31.1.0 [110/300] through 192.168.99.2, 3d17h, FastEthernet0

  O E2 172.31.0.0 [110/300] through 192.168.99.2, 3d17h, FastEthernet0

  O 192.168.11.0/24 [110/4] through 192.168.99.2, 3d17h, FastEthernet0

  C 192.168.98.0/24 is directly connected, BVI98

  C 192.168.99.0/24 is directly connected, FastEthernet0

  O 192.168.20.0/24 [110/2] via 192.168.99.2, 3d17h, FastEthernet0

  192.168.5.0/31 is divided into subnets, subnets 1

  O 192.168.5.2 [110/2] via 192.168.99.2, 3d17h, FastEthernet0

  192.168.6.0/31 is divided into subnets, subnets 1

  O 192.168.6.2 [110/3] through 192.168.99.2, 3d17h, FastEthernet0

  192.168.1.0/24 [110/14] through 192.168.99.2, 3d17h, FastEthernet0

  O * E2 0.0.0.0/0 [110/1] via 192.168.99.2, 1d09h, FastEthernet0

  Thank you

  Mahesh

  Mahesh.

  Indeed, solution based purely crypto-card are not compatible with a routing protocol.  Crypto card however is the legacy config we support on IOS. The best practice is to use the protection of tunnel. Any routing protocol would work then.

  for example

  https://learningnetwork.Cisco.com/docs/doc-2457

  It's the best solution we currenty have

• How can you find your wep or wpa key to go on the internet I have a linksky route

  on the internet, computer wife XP runng had no problem, then when it turned on today that it asks for the wep or wpa key and I don't know what it is.

  Hi WILLIAMBERGEN,

  In a wireless network, the WPA key is a password that protects the network against outside intrusion. If a wireless router is configured with WPA encryption, you need the WPA key for access to the network and to make changes to your network settings

  We will check if the following is useful.

  a. open your web browser. In the address bar, type http://192.168.1.1 and press to enter. It is the default IP of many wireless routers. If this does not load a web page, see the manual of your router to the IP address of the configuration.

  b. on the screen that appears, you will be asked to enter your username and password. If you do not know your user name and password, try the default name of the user and the password of your router.

  c. If you are unable to log in or search for the user name and password of your router, reset the router.

  d. in your router settings, look for a "safety" or "wireless security" tab open this tab and the WPA key should be displayed.

  You can contact the support of router for more information.

• I can't connect to my router and my system XP Pro/SP3 has NOT installed the automatic Wireless Configuration service. How can I get that re-installed?

  I have the latest driver for my Linksys WPC54GS PCMCIA card. The Linksys software does not support WPA security, which supports my rout (and I do not want to use WEP).  The zero wireless Configurator, this is what I need, but the service is not installed on my Windows XP Pro w / SP3 System.

  Hello

  You need not be. I posted a link to google cache, so keep scrolling down, the answers are displayed below. It contains details on the manual creation of the registry key for the zero configuration service.

  You can also export to a working system.

  See you soon.

• Dell 8132F does ACB support?

  Hello

  I suggest that 8132F supports the routing of basic political function?

  Thank you!

  It does not support ACB on the latest firmware. Here is a link to the firmware download.

  http://Dell.to/1Ngk5Hd

  And here is a white paper by ACB configuration.

  http://Dell.to/1ZwglZ9

  Let us know if you have any questions.

• InterVLAN routing for S4810 VLT

  Hello

  I just want to clarify things because I get confused all intervlan routing if it is possible to implement if I used VIDEO Lottery devices

  First of all when I configured the VLT field in sweetheart two switches (S4810), I need to have an itinerary for my VLAN

  -what I used intervlan routing is my favorite, but when the peer routing, active in VLT intervlan routing is applicable or supported in routing peers. ?

  -also all configurations of the two peer switches must be identical or same

  • example: when I configured intervlan routing in Peer-1, also, I need to configured intervlan routing in Peer - 2

  I want to have an answer if I need intervlan or OSPF configuration with this problem

  Thank you very much

  BRENT

  This technical guide I think answer all your questions. Yes, you can have VLAN routing enabled on the switches. The guide goes through many examples, including examples of switches that is configured to perform the VIRTUAL LAN routing. It also includes examples of configuration that you can use as a reference.

  http://Dell.to/1wfDl3n

  Let us know if this helps out.

• Unable to connect to Homegroup Windows 7 between the Modem to the PC and the Modem to the router for PC users.

  I want to talk about WIRED computers, do not speak of wireless.

  I have 3 PC:

  -2 are connected via Modem directly to the PC.

  -1 is connected through router, and the router is connected to the modem.

  The problem, this is it, it cannot detect the homegroup that I created on the computer that is directly connected by modem.

  The 2 PC via modem are perfectly detected and connected to the homegroup, so I want to know what I would do to another PC (which is connected to the router via modem) detects the homegroup, I had already created?

  Help, please.

  A Modem can have only two ports, connect to the internet (Wide Area Network) and the second to a SINGLE local device. In most cases the internet Service Pwill provide with only an IP address so itself cannot connect to more than one at a time. In current solutions, it is very rare for a Modem to use. If as you say, you have several devices connected to this unit then he himself is a router but possibly with the Modem built in if you have ADSL ISP.

  If your second unit is also a router then that explains why you cannot connect all devices in the same residential group.

  Router 1 has created a Local Area Network including both PC and the WAN port on the Router 2. Router 2 has created another independent local network with the 3rd PC. It is very likely that the two local networks will be IPv4 and traffic can be routed between them correctly in both directions according to the two local networks subnet ranges.

  Even if they are properly configured to allow traffic that HomeGroup requires IPv6 that some home routers support fully and every Member of the residential group must be on the same LAN anyway, he will not support a routed connection.

  Remove the 3rd PC of the 2nd router and plug it into the direct 1 router, remove the router 2nd the 1st in order to free the port. 3 all PCs are now on the same local network and communicate both IPv4 and IPv6, and homegroup should work.

  If you need additional ports provided by the 2nd router for other devices is not part of this problem then consider replacing it with a switch. If you use Router 2 for other devices Wi - Fi irrelevant then you need a wireless access Point.

• [Urgent] E3276 USB Dongle is unable to connect to RV325

  Dear experts - I need your help. According to the list of dongle, Cisco RV325 is supported USB dongle E3276. However, I can not connect with it properly (you can see the USB1 is connected and seeing USB Dongle appears connected). I'm trying to use this dongle with Windows to access the 4G network properly. Help, please! Please give me some advice!

  Kind regards

  Tommy

  Hi ImkTommy79:

  If you need help for this dongle, please contact the Small Business Support Center (HWC) and ask them to escalate the case to L2 and so the beta code can be assured. The Document should be updated...

  https://supportforums.Cisco.com/document/12316401/dongle-support-rv320-and-rv325

• Unable to connect via the wireless router "problem with wireless adapter or access point" _

  Hello

  I recently replaced my old Toshiba laptop with a new model of Toshiba Satellite L500/033HNX, it installed Windows 7.

  The problem is that I can't connect to my wireless network. I am currently connected via Ethernet cable to my Linksys router.

  I had help from my internet service provider, the installation correctly the problem not because of the connection.

  I had a Linksys online support, the router is a wireless, model - WAG54G ADSL gateway, is not the problem of all the correct settings and other devices can connect via my wireless network. I ran Dr. connectivity several times and it is always impossible to connect, "problem with the wireless adapter or access point.

  OK, you're my next hope to solve the problem can you HELP Please!

  Hi, JoelbX
  I want to thank very you much for your support and effort do to help me solve this problem, but we receive have been, and I don't want to waste any more of your valuable time, so I am the son of closing and deleting of Tring in Microsoft Answers.
  All the best
  Tring

• redirection of IP in FWSM in routed mode.

  How can I enable IP forwarding in FWSM? When I hear the traffic from a single interface needs to be redirected to another device in the same interface his past does not in the normal scenario. Redirection is supported in routed mode?

  It depends,

  If you are running<2.2, then="" you="" can't,="" ref.="" the="" q&a="" question="" "can="" i="" operate="" the="" pix="" in="" a="" "one="" armed"="" configuration?"="" (the="" 1.1.x="" runs="" on="" a="" derivative="" of="" pix="" 6.0="" and="" 6.2)="">

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_qanda_item09186a0080094874.shtml#add

  If you run > = 2.3, then you can by activating the function "permit same-security-traffic intra-interface":

  http://www.Cisco.com/en/us/products/hw/switches/ps708/products_module_configuration_guide_chapter09186a00802c6417.html#wp1052504

• IPSEC and routing protocols

  Hello world

  I read that IPSEC does not support routing with VPN's Site to the other protocols because both are Layer4.

  This means that if Site A must reach the B Site over a WAN link, we use static IP on the Site A and Site B router?

  In my lab at home I config Site to Site VPN systems and they work correctly using OSPF does that mean that IPSEC supports the routing protocol?

  IF someone can explain this please?

  Thank you

  Mahesh

  There is no problem with the routing on IPsec protocol, there are limits to some implmentations.

  Our old (strives, but still popular) crypto maps where such implemtation.

  What you need to remember, is that to make routing protocols (more) on IPsec, you must ensure that multicast is allowed through, i.e. your traffic selectors should be postponed. Another thing is that some of these protocols do a check if Hellos were recived leave a subnet connected etc etc. Of course, this isn't a problem with BGP (or most of the problems can be overcome easily).

  New implementations - side Cisco using protections of tunnel - we can run protcols routing on IPsec with very few restrictions.

  M.

• ASA 5505 in router Mode can implement the MAC ACL

  Hi all:

  My client request can the Cisco ASA 5505 implement MAC ACL in Cisco ASA 5505, who is now running in router Mode.

  Can anyone help answer this?

  I tried to search the document and also tried the ASDM in the Cisco ASA 5505 but couldn't see a way to do the ACL by MAC address.

  At the same time can also help me find the command line using the ASA 5505 able to run MAC ACL in router mode?

  Thank you very much!

  Warm greetings,

  TangSuan Tan

  MAC ACL is not supported in Routed mode, only in Transparent mode.

  Here is the command for your reference:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/command/reference/A1.html#wp1598101

  And here is the ethertype supported:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/access_rules.html#wp1083699

• I have 2 imacs and a laptop computer and you want to back up all three wireless via time capsule on my existing wifi network. If we can also use the time capsule as my wifi and replace my uverse wifi, that would be great. possible?

  I have 2 imacs and a laptop computer and you want to back up all three wireless via time capsule on my existing wifi network. If we can also use the time capsule as my wifi and replace my uverse wifi, that would be great. possible?

  If you want to make sure that you will be able to get the Apple support in case of problems or questions with your backups, you must use the wireless Time Capsule to back up your Mac.

  As long as the time Capsule provides a wireless signal, you can decide who to your 'main' network, then use it wireless Uverse for "guest", or children. If you do not need the Uverse router/modem wireless at all, it is possible to turn off wireless on the device and make it work only as a support modem/router...with Uverse wired.

  At this point, you can start thinking about how you want to configure things and get back in touch if you need some advice on how to do it.  We need to know what operating system that uses the Mac that you normally use to administer the time Capsule, provide good instructions, if you need it.