model orientation of 2821 router please?

Similar Questions

• New user pages :) I seletced arrow shape, he does exactly that for my needs, can I now register as a form of model for easy future use please? Thank you!

  New user pages I seletced arrow shape, he made exactly that for my needs, can I now save it as a form of model for easy future use please? Thank you!

  Hi PAYGPI,

  A Pages document with some arrows. With a selected arrow Panel Format (right) organize tab > stay on the Page. You can then move around the page.

  

  Menu > file > save as template.

  In the model picker, rename it. I used the name clip art arrows. It appears in the template selector > my templates.

  

  To rename or delete a custom template (in my models) right click or control click on this model:

  

  Please call with questions.

  Kind regards

  Ian.

• I deleted the program that control access on my hpkeyboard key model # sk - 32960. Help, please

  I deleted the program that control access on my hpkeyboard key model # sk - 32960. Help, please

  Hello

  What operating system do you work?

  You can try to download the drivers from the link below and check the status.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=PV-42543-1&LC=en&cc=us&DLC=en&product=3298300&OS=228&lang=en

• Need help to connect the old Windows XP to new wireless router, please

  Hello
  I have an old desktop running Windows XP Edition family 2002 version, which has been connected to a Netgear WG311 802.11 wireless router g. I was unable to connect to other computers, so I replaced the Netgear with an E1200 Linksys wireless router. Now, all other computers find the Linksys router, but the older Windows XP desktop will not (because I don't use it to configure the router?).  How to connect your old computer to Windows XP to the new router, please? Thank you very much for your help.
  Walt

  Hello
  I have an old desktop running Windows XP Edition family 2002 version, which has been connected to a Netgear WG311 802.11 wireless router g. I was unable to connect to other computers, so I replaced the Netgear with an E1200 Linksys wireless router. Now, all other computers find the Linksys router, but the older Windows XP desktop will not (because I don't use it to configure the router?).  How to connect your old computer to Windows XP to the new router, please? Thank you very much for your help.
  Walt

  The problem is probably that the Linksys E1200 is a wireless-N Router and your former Office no doubt has a wireless adapter that is only capable of wireless-G (or perhaps Wireless G and B).

  Are adapters wireless in your other computers wireless - n?  If so, it perhaps is the reason why they could not connect to your old G of Netgear wireless router.

  You can get a new wireless-N for the office adapter or configure the E1200 wireless g available.

• Problem starting the Cisco 2821 router

  Hello world

  I have cisco 2821 router. I am facing problem starting.

  someone suggest me what is the problem.

  Thanks in advance...

  VERSION of the SOFTWARE system Bootstrap, Version 12.4 (13r) T, (fc1)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 2006 by cisco Systems, Inc.

  The ECC memory initialization
  .
  C2821 platform of 262144 KB of main memory
  Main memory is configured for 64-bit with ECC active

  ReadOnly initialized ROMMON
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80

  load complete, point of entry to the program: 0x8000f000, size: 0x26bc2cc
  Decompression of self-image: #.
  ################################################################################
  ################################################################################
  ################################################################################
  ################################################################################
  ################################################################# [OK]

  Smart init is enabled
  Smart init is sizing iomem
  MEMORY_REQ TYPE ID
  0003E8 0X003DA000 C2821 Mainboard
  1A 0X0025178C E3 0001AB
  0X00263F50 VPN on board
  0X000021B8 embedded USB
  Swimming pools public buffer 0X002C29F0
  Swimming pools public particle 0 X 00211000
  TOTAL: 0X00D65284

  If all memory conditions above are
  "UNKNOWN", you could use a non supported
  configuration or there is a software problem and
  the system may be compromised.
  Rounded IOMEM to: 14 MB.
  Using iomem of 5 percent. [14 mb / 256Mb]

  Legend restricted rights

  Use, duplication, or disclosure by the Government is
  subject to such restrictions as set out in paragraph
  (c) Commercial - limited computer software
  The rights to FAR clause 52.227 - 19 and subparagraph s
  (c) (1) (ii) rights to technical and computer data
  Clause of DFARS 252.227 - 7013 section software.

  Cisco Systems, Inc.
  170 West Tasman Drive
  San Jose, California 95134-1706

  Cisco IOS software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4 T7 (9)
  Version of the SOFTWARE (fc3)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2008 by Cisco Systems, Inc.
  Last updated Friday, January 10 08 16:35 by prod_rel_team
  Image text-base: 0x400B1E74 database: 0x434A9AC0

  ERROR detected on Bus PCI1
  Try REINSTALLING all the modules in the system
  pci1_int_cause 0 x 00000240,
  pci1_err_addr 0 x 00091009, pci0_err_cmd 0x0000000A
  PCI Master Read parity error
  Abort target PCI

  R0 = r1 = r2 FFFFFFFF FFFFFFFF = 0 r3 = 45 80000 r4 = 0
  R5 = 303 r6 = 0 A7 = 1 = 0 = 100000 r9 r8
  R10 = 0 r11 = 465E4369 r12 = 0 r13 = 465E436A r14 = 0
  R15 = r16 r17 8 = 0 = C100 r18 = 0 r19 3400 101 =
  R20 = r21 0 = 40096828 r22 = FFFFFFFF r23 = r24 FFFF00FF = 0
  R25 = 469AAC64 r26 = 0 = 469AAC60 r28 = 0 = 469AAC5C r29, r27
  R30 = 0 r31 = 469AAC58 r32 = r33 FFFFFFFF = r34 = FFFFFFFF FFFFFFFF
  R35 = r36 = r37 = r38 = r39 FFFFFFFF FFFFFFFF FFFFFFFF FFFFFFFF = FFFFFFFF
  R40 = FFFFFFFF = FFFFFFFF = FFFFFFFF = FFFFFFFF r44 r43 r42 r41 = FFFFFFFF
  R45 = r46 = r47 = r48 FFFFFFFF FFFFFFFF FFFFFFFF = r49 0 = 469AACD0
  R50 = 0 0 = 0 r53 r51 = r52 = 3040A 801 r54 = FFFFFFFF
  R55, r56 = FFFFFFFF = FFFFFFFF r58 r57 A000F000 = = 0 = 465E4358 r59
  R60 = r61 = r62 FFFFFFFF FFFFFFFF = r63 = 0 402E4B10
  GENS = 3400 103 mdlo_hi = my 0 = 251 00
  mdhi_hi = 0 = 0 badvaddr_hi = FFFFFFFF mdhi
  BadVAddr = cause = epc_hi 0 = FFFFFFFF FFFFFFFF
  EPC = 402E4B08 err_epc_hi = err_epc FFFFFFFF = FFFFFFFF

  ERR-1-FATAL %: interruption of the fatal error, reload
  err_stat = 0 x 0

  = Posts from Flushing (02: 37:51 UTC Wednesday, may 18, 2016) =.

  Messages in queue:

  02:37:51 UTC Wednesday, may 18, 2016: interrupt exception, signal CPU 22, PC = 0 x 0

  --------------------------------------------------------------------
  Software fault possible. On reccurence, you perceive
  crashinfo, 'show tech' and contact Cisco Technical Support.
  --------------------------------------------------------------------

  -Trace =
  $0: 00000000, AT: 00000000, v0: 00000000, v1: 00000000
  A0: 00000000, a1: 00000000, a2: 00000000, a3: 00000000
  T0: 00000000, t1: 00000000, t2: 00000000, t3: 00000000
  T4: 00000000, t5: 00000000, t6: 00000000, t7: 00000000
  s0: 00000000, s1: 00000000, s2: 00000000, s3: 00000000
  S4: 00000000, s5: 00000000, s6: 00000000, s7: 00000000
  T8: 00000000, t9: 00000000, k0: 00000000, k1: 00000000
  GP: 00000000, sp: 00000000, s8: 00000000, ra: 00000000
  EPC: 00000000, ErrorEPC: 00000000, GENS: 00000000
  MY: 00000000, MDHI: 00000000, BadVaddr: 00000000
  CacheErr: 00000000, DErrAddr0: 00000000, DErrAddr1: 00000000
  DATA_START: 0X434A9AC0
  Cause 00000000 (Code 0 x 0): Exception of interruption

  Writing crashinfo in flash: crashinfo_20160518-023752
  No reboot to warm storage
  System received a system error *.
  signal = 0 x 16, code = 0x0, context = 0 x 46905718
  PC = 0x40096d7c, Cause = 0 x 20, State Reg = 0 x 34008002

  Software Cisco IOS, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4 (9)T7
  Version of the SOFTWARE (fc3)

  OK, the router is running on a train of "T".

  ERROR detected on Bus PCI1
  Try REINSTALLING all the modules in the system
  pci1_int_cause 0 x 00000240,
  pci1_err_addr 0 x 00091009, pci0_err_cmd 0x0000000A
  PCI Master Read parity error
  Abort target PCI

  Remove any all NM/NME or WIC/HWIC cards and restart again.  If the router is able to start properly, upgrade the router to a higher version.  DO NOT use another "T" train if it is needed.  Use instead a train of "M".

• change password cisco router please?

  I have been using my desktop computer and it crashed after 15 years.

  I started using my laptop and discovered that people use my wifi and

  password. So I want to change it so that nobody is using my wifi unless I have let

  them also.

  Can someone please tell me how. When I phoned cisco they said my warranty

  has expired, and they refused to tell me how to change my password unless

  I paid $39.95.

  I am disabled and I live on a small income if I pay them that I won't be able to pay

  my rent.

  Thanks for your time and your help.

  Google the brand and model of your router + factory reset or manual and who should be able to help out you.

• 2821 router to access T1 on LAN

  I'll put up a Cisco router for a T1 line for the first time and I hit a barrier. The router, a 2821 with WIC-1DSU-T1-V2 is online (all statuses are rising and I can ping outside sites). However, a laptop computer connected to the router can not access the Internet outside.

  My router (sterilized) static IP from the ISP is 10.0.0.222. It is on the 10.0.0.220/30 network, with a broadcast address of 10.0.0.223/30. The ISP gateway is 10.0.0.221

  I have the Gigabit Ethernet port game with an IP address of 192.168.1.1/24

  Here is the configuration:

  !
  version 12.4
  service configuration
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  No dhcp service
  !
  router host name
  !
  boot-start-marker
  boot-end-marker
  !
  enable secret 5 XXXXXXXX
  activate the password XXXXXX
  !
  No aaa new-model
  no ip Routing
  !
  !
  no ip cef
  !
  !
  name-server IP 10.0.0.3
  name-server IP 10.0.0.4
  !
  !
  !
  !
  !
  interface GigabitEthernet0/0
  no ip address
  no ip route cache
  Shutdown
  automatic duplex
  automatic speed
  No cdp enable
  !
  interface GigabitEthernet0/1
  IP 192.168.1.1 255.255.255.0
  no ip route cache
  automatic duplex
  automatic speed
  No cdp enable
  No mop enabled
  !
  interface Serial0/0/0
  IP 10.0.0.222 255.255.255.252
  encapsulation ppp
  no ip route cache
  no fair queue
  !
  default IP gateway - 10.0.0.221
  IP forward-Protocol ND
  !
  IP http server
  !
  !
  control plan
  !
  !
  Line con 0
  exec-timeout 0 0
  line to 0
  line vty 0 4
  password XXXXXX
  opening of session
  !
  Scheduler allocate 20000 1000
  No extensive process CPU
  No pork process autoprofile cpu
  !
  end

  Since the router command line I can ping 10.0.0.221 (Gateway ISP) as well as external IP addresses. Domain names resolve correctly and can be crazy. I ping the router of my regular Internet connection.

  However, when I join a laptop the GigabitEthernet0/1 (static IP address of the laptop is 192.168.1.2) I can't seem to the outside network. I can ping the map T1 and Ethernet card address, but not the ISP (10.0.0.221) gateway or all other external addresses.

  I tried to adjust laptop, gateway 192.168.1.1 and 10.0.0.222. Set to 10.0.0.221 gives an error "network unreachable".

  I am new to Cisco routers, so I guess it's something simple, maybe an IP need rule of routing or something?

  In summary: the router is online on T1, can ping and ping, but laptop connected to the ethernet router cannot be accessed outside the network.

  Thanks for any help.

  Hello

  I guess the problem is that your ISP does not know how to route the packets back to your 192.168.1.0 subnet. If you ping the router with the address of the source of your inside interface it will confirm if this is the case or not.

  You can run a dynamic routing with your ISP Protocol which I guess is not the solution preferred the complexity. You can ask the ISP adds a route to your network, but again once I guess that's not an option.

  The most appropriate solution would be to run NAT Network Address Translation on your serial interface and use overhead NAT to translate entire your network to your unique WAN address.

  Hope that helps.

  http://www.Cisco.com/c/en/us/support/docs/IP/network-address-translation...

• 2821 router support

  Dear Sir.

  Praposed connectivity for voice between neighborhoods General remote IP phones to analog phones is regarding the attached flowchart. Cisco 2821 routiters with IOS 12.2 are interconnected (v.35) line using rented between HQ FOR REMOTE SITES. To remote sites analog phones are connected to the FXS ports. To end HQ PABX with the required number of user liseces for IPPHONES is connected to the router via an ethernet switch. It is the installation of the network shown in the diagram is correct for connectivity you want between phones ip HQ for analog phone of BRANCH. What should be the requirement of configuration in the router for connectivity abive.

  Please give me some examples

  Thank you & best regards

  Srinivas

  Hello Srini,

  your lab configuration is similar to what I guessed.

  the IP PBX has an IP address on the same subnet IP to the lan from 2800 HQ interface.

  You can run a routing protocol on the V.35 point - to - point link in order to advertise the subnet LAN of HQ.

  In addition to what was already mentioned in my first post the use of QoS for a priority queue VoIP calls is recommended.

  The part of QoS can be added later to the installation of laboratory.

  Hope to help

  Giuseppe

• cannot play an online game because my video card does not support shader model. generally work started recently please help

  usually, I play a game called League of legends online and last night I tried to get into a game and got an error message that reads. DirectX error check and make sure that your video card supports shader 2.0 model and uses drivers from the manufacturer. I've played a few games yesterday but it was all of a sudden when it stopped to let me play. Help, please. Thank you

  Hi Casey,.

   
   
  1. do you use Internet Explorer to play games online?
  2. If so, what is the version of Internet Explorer installed on your computer?
  3. have you made changes to your computer recently?
  4 are you facing this problem only with shader model 2.0?
   
  If you use Internet Explorer to play games online, I suggest you to follow the steps and check if it helps.
   
   
  Method 1: Follow the link and check if that helps.
  The problems of games online using Internet Explorer
   
   
  Method 2: You can also check out the link and check if it helps.
  Run the DirectX Diagnostic tool
   
   
  Method 3: Update cheque and card video if this can help.
  Updated a hardware driver that is not working properly

• [Noob questions] Model oriented programming OBJECT and event Flex

  Hello, I have two very easy questions for an expert - I think.

  (1) issue-oriented object

  If I have a

  UserElement extends the Image

  UserImage extends UserElement

  UserText extends UserElement

  ...

  UserSomething extends UserElement

  Each UserSomething derived from UserElement has an editElement method that can be placed in the superclass UserElement needs to look exactly because in this journal.

  Now, from the root of the Application, I have to call the editElement, but I'd rather not be forced to have a giant switch inelegant structure... There is a way to dynamically cast to the right class?

  (2) issue of event model

  I read the documentation and googled around, but if I have this structure

  Application

  Canvas1

  Control1

  Canvas2

  CONTROL2

  and I send Control1 event, the full path is Application > Canvas1 > Control1 > Canvas1 > Application. But if I need control2 to know that this event is FAILED, the only way I see is to call a method in the Application control2. Is this correct or there is a way to redirect the event in a way to broadcast?

  Thanks in advance for anyone who wants to answer

  maestro91,

  Answer, no, protected Alexander is very good and I used it in this way - protected is visible to inherited classes OK.

  You should be able to:

  var r: derivedClass;

  a = new derivedClass();

  function do_something (b: baseClass)

  {

  test to find out which class that I was adopted, then derived

  ((derivedClass) b) .editelement ();

  above must call the correct method

  }

  You must explicitly cast to ensure the right call gets shot, but you used baseClass as an argument, so you can send your derived through classes.

  Richard

• HP C4580 not scan to PC. I need help to configure my Netgear router please :)

  Hello

  I've read here, the threads that talk about this printer prints only not to or from a PC - my problem is that the C4580 go scan from my PC, but will not scan to PC.

  I found an answer from someone who has had the same problem earlier this year, but I do not understand what to do.

  Here's the answer:

  "I have ordered mine entering the settings from my router (Netgear) page and setting the built-in firewall rules. "The internal firewall was blocking the printer, I could print, scan using the computer, just could not scan from the printer to the computer.

  Also, I have a Netgear router, but could do with help on how to do the same thing as the person above.

  Thanks in advance for any help!

  Sorry, I don't need help after all

  It was not the router requires a configuration, it is the firewall that was a block that should be changed to "allow".

  My "all-in-one" now does everything it is supposed to do

• Drop ' n Go subnet to breast pre-existing network - Help with routing please

  Hi all

  I consider myself the best entry level when it comes to the Cisco ASA 5505, and I appreciate help or direction that someone would be able to provide regarding this question, I'll have. I'm sure there is something out there for this, but I was still not able to understand this with what I found.

  We currently have our installation of infrastructure like this: modem(69.14.72.6/255.255.255.248)-> ASA (192.168.1.1)-> Switch-> hosts and Servers(192.168.0.X\24).

  What I'm trying to do is to drop in a small router somewhere within this network with its own subnet and be able to communicate back him 192.168.0.X network, so it will look something like this: modem-> ASA-> Switch-> hosts and Servers(192.168.0.X\24) & hosts and Servers(192.168.1.X\24).

  I will allow this traffic if all goes well, then that only have 2 interfaces configured on the SAA (0/0 and 0/1-0/5 inside) outside and without changing the configuration of the switch. A few key phrases that come to mind from my research so far are "Hair pin" and "permit same-security-traffic intra-interface". Also, I am aware of the port-forwarding and as I understand it would not as convenient to configure a rule for each device connected to the 192.168.1.X\24 network.

  I hope someone can help me with this question, I've been at this for 3 weeks now.

  Thanks again to all!

  EDIT: Here is a diagram to help explain what I'm trying to do. The area in red is what I'm trying to add to the others that I already have.

  

  Hi James,

  For the route between the 2 networks, that you will need to either use a layer 3 switch or a "router on a stick".

  Installation of a layer 3 switch would interrupt less to your existing network.

  You are then ASA "inside" interface--> Layer 3 Distribution Switch--> 2 or more switches to access

• Error message 'Please select the access point or wireless router to set up' when you set up a network

  Original title: set up a network.

  I want to create a wireless network for the games, and when I click on the network. A screen comes written on this "Choose the access point or wireless router to set up" and that "it might take 90 s for devices reconfigured to appear on your computer.

  But no device never appears below it, even after 90 minutes.
  Please help me with this.
  It was so easy in windows 7.

  Hi Manas,

  What is the brand and model of the Wireless Router/Access Point?

  Given that the issue has not persisted in Windows 7, there is a chance that the wireless router/Access Point is not compatible with Windows 8.

  Please check the links below on the implementation of a network.

  http://Windows.Microsoft.com/en-in/Windows-8/Setup-home-network

  http://Windows.Microsoft.com/en-in/Windows-8/what-you-need-Setup-home-network

  http://Windows.Microsoft.com/en-in/Windows/set-up-wireless-router#set-up-wireless-router=Windows-8

  http://Windows.Microsoft.com/en-in/Windows-8/Add-device-or-PC-to-network

  Answer please if you have any questions.

• Master point, BOM, models of routing to import legacy objects in Oracle

  We need new models of import to import us master records point, bills manufactured and prefabricated ranges in R12.

  Can anyone guide hoe to develop and create new import models to include the new fields in R12.

  For routing, please develop a model that allows the import of the operation Standard code, if it exists, but also display on the model columns / fields required if code no. Operation Standard is available.   Let me know if any questions.

  Hello

  You can download your data in Excel to a staging table using sql * loader or any other tool.

  After downloading the data, you must complete the interface tables in my previous post.

  After the filling of the interfaces, you must run the program BOM & Routing simultaneous Import to import legacy data.

  For more details, please visit the following links.

  http://oracleappss.blogspot.in/2008/07/BOM.html

  http://sairamgoudmalla.blogspot.in/2010/08/to-import-routing-with-operations-and.html

  http://www.Club-Oracle.com/resources/BOM-interface-document.703/

• router to router 2821 encryption

  How to secure this scenerio?

  (1) site A has a 2821 router and an IP connection to the site C. 2821 on another organizations IP network.

  (2) site B has a router 2821 with an MPLS connection at the site of the C-2821.

  It's pretty easy to connect and get plain text connections and tunnels WILL work, but I'm leaving my network open to other agencies or MPLS service provider.

  I think little flavor of encryption between routers with tunnels GRE routes real traffic.

  Thank you in advance for recommendations and examples of config.

  Hi Tod,

  You can deploy a separate acl on the physical interface, which allows only the tunnel itself (udp/500 and esp). The ACL in the VTI would control the traffic through the tunnel.

  Rgds,

  MiKa