3.5.1 to 506th Pix VPN Client using IPsec over TCP

Similar Questions

• Client VPN with tunneling IPSEC over TCP transport does not

  Hello world

  Client VPN works well with tunneling IPSEC over UDP transport.

  I test to see if it works when I chose the VPN client with ipsec over tcp.

  Under the group policy, I disabled the IPSEC over UDP and home port 10000

  But the VPN connection has failed.

  What should I do to work VPN using IPSEC over TCP

  Concerning

  MAhesh

  Mahesh,

  You must use "ikev1 crypto ipsec-over-tcp port 10000.

  As crypto isakmp ipsec-over-tcp work on image below 8.3

  HTH

• IPSec over TCP on PIX 501F to the catalog

  Hello

  Is there a way I can configure IPSec over TCP as default configuration in the PIX firewall. I'm under 6.3

  The PIX does not support IPsec over TCP. It doesn't support NAT - T, which is IPSec over UDP/4500, which houses also of the Cisco VPN client. Just add the following command on the PIX:

  ISAKMP nat-traversal

  The PIX and VPN client auto-négociera if necessary IPSec encapsulation. See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/gl.htm#wp1027312 for more details.

• IPSec over TCP on Pix

  Nice day

  I would like to know if there is the possibility of configuring IPSEC over TCP on the pix Firewall.

  This features are supported by the latest Pix OS (6.3.3)?

  Thank you

  Diego

  The pix does not support ipsec over tcp. It supports NAT Traversal that is ipsec over udp. IPSEC over tcp is compatible with the VPN concentrator. The next link talks about NAT traversal.

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/config/ipsecint.htm#1057446

  Take a look at this link to configure IPSec over TCP on a VPN 3000 Concentrator

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800946bc.shtml

• With PAT on Cisco PIX VPN client

  Dear all,

  I have a PIX 515 to the main site with the IPSec security is enabled. Homepage user using 3.x VPN client connects to the PIX for VPN access. When user Home use real IP, I can ping to the local network of the main site. However, when the Home user using a router with PAT, the VPN can be established.

  Is there a setting I should put on PIX, VPN client or router?

  Thank you.

  Doug

  And if you still have problems, upgrade your pix, 6.3 and usage:

  ISAKMP nat-traversal

  But the first thing would be to check the IPSEC passthrough as Ade suggested. If the device is a linksys check the version of the firmware as well.

  Kind regards

• VPN IPsec over TCP on PIX 6.3

  Hi all:

  Does anyone know how config IPsec over TCP on PIX6.3?

  Thank you all...

  Ted Wen.

  Hello

  You can enable IPSec over TCP to PIX Security Appliance Software Version 7.0 with the command "isakmp ipsec-over-tcp port. But I can't make it work and have posted my problem on the Forums of Discussion.

  Thank you.

  B.Rgds,

  Lim TS

• IPSec over TCP works on VPN 3030 interface (3) external?

  I configured the third external interface and can connect with the ESP and UDP tunnel, but not with IPsec over TCP.

  The customer says:

  Unexpected TCP control packet received a.b.c.d, src port 10000, port dst 4408, flags 14: 00

  the hub said nothing, although I tried several event classes

  the document said "IPSec over TCP works with the VPN client software and hardware VPN 3002 client. It only works on the public interface. It is a client to the function of hub only. It does not work for LAN-to-LAN connections. "

  This means - it works on the public interface real, physical?

  or it should work on the external interface if I click on the checkbox to its public interface?

  Thanks for any advice,

  Martin

  IPSec over TCP is designed to operate only on the real public interface #2.

  There were a few technical reasons behind it, among them:

  (1) some clients cancel their tunnels on the private interface (one-arm-config) and that would cause a headache when trying to HTTP through the VPN 3000 if IPSec/TCP has been installed for Port 80/443. We decided to pull out of the private Interface.

  (2) that the external interface #3, we have chosen not to enable IPSec/over TCP Dynamics fielterso n it mainly because of the load balancing.

  Since the LB only works on real public interface #2, even once, we chose to leave

  IPSec/TCP out of it.

  Nelson

• Intercommunication 506th PIX VPN to VPN windows server

  Most of he says title.

  I got a 831, and I only needed to port before the pptp tcp port 1723 to my Windows 2003 VPN server.

  Got 506th pix until 2 days ago and I cannot find a way to pass traffic. Obviously tcp 1723 is mapped statically. And I checked this command for accuracy.

  Configuration mode, enter the following command:

  fixup protocol pptp 1723

• Through a PIX VPN client

  Hello

  It seems to me having confused TAC with this question:

  I have a client who has two firewalls PIX 501. One in DC (pix - a) and one in San Diego (pix - b). They are both connected via a static IPSec VPN. Works fine, no problem. I also set up two of them to accept connections from Cisco VPN Clients for these people who are on the road a bit. It also seems to work in most situations.

  However, when you try to connect to one of these two firewalls with the Cisco VPN Client when I'm behind other PIX (resembling a third party site that is not attached to a pix - a or pix - b by all means of transport), establishes the tunnel, but I can't move the traffic to the Remote LAN. At first I thought it was due to the NAT on my home PIX (pix - c). Then, I tried to work, behind a PIX who don't use NAT (pix - d) and got the same results. I should mention that trundle making IPSec is enabled on pix - c and pix - d.

  Establishes the VPN connection very well from outside pix - c or pix - d. I can connect and ping perfectly.

  I thought this would be a simple "oh yes, this turns ' or"this is is not supported", but the TAC engineer who picked up my case does not seem to grasp the concept, nor understand how to read my .gif image of visio four firewalls PIX drawn in the exact scenario described above.

  Thank you

  evt

  What version of IOS is there on pix - a, pix - b?

  What game of transformation for vpn clients do you use?

  In all cases, you must enable NAT traversal on pix - a, pix - b.

• How to match tunnel-group with auth ASA 8.2 and IPSec VPN Client using digital certificates with Microsoft CA

  Hello

  I set up a lab for RA VPN with a version of the ASA5510 8.2 and VPN Client 5 software using digital certificates with Microsoft CA on a Windows 2003 server. I did the configuration based on this document from Cisco's Web site:

  http://www.Cisco.com/en/us/partner/products/ps6120/products_configuration_example09186a0080930f21.shtml

  Now, the vpn works fine, but now I need to configure a tunnel-different groups so I can provide different services to different users. The problem I have now is that I don't know how to set it up for the certificate is the name of tunnel-group. If I do an ASA debug crypto isakmp I get this error message:

  % ASA-713906 7: IP = 165.98.139.12, trying to find the group through OR...
  % 3 ASA-713020: IP = 165.98.139.12, no group found by matching well payload ID: unknown
  % ASA-713906 7: IP = 165.98.139.12, trying to find the group via IKE ID...
  % 3 ASA-713020: IP = 165.98.139.12, no group found by matching well payload ID: unknown
  % ASA-713906 7: IP = 165.98.139.12, trying to find the group via IP ADDR...
  % ASA-713906 7: IP = 165.98.139.12, trying to find the group using default group...
  % ASA-713906 7: IP = 165.98.139.12, connection landed on tunnel_group DefaultRAGroup

  So, basically, when using certificates I connect always VPN RA only with the group default DefaultRAGroup. Do I have to use a model of different web registration for application for a certificate instead of the user model? How can I determine the OU on the user certificate so that match tunnel-group?

  Please help me!

  Kind regards

  Fernando Aguirre

  You can use the group certificate mapping feature to map to a specific group.

  This is the configuration for your reference guide:

  http://www.Cisco.com/en/us/partner/docs/security/ASA/asa82/configuration/guide/IKE.html#wp1053978

  And here is the command for "map of crypto ca certificate": reference

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/C5.html#wp2186685

  Hope that helps.

• 6500 IOS router Cisco VPN Client using DHCP no Pool of IP

  Hey guys,.

  I have a little trouble trying to get my vpn client to use a dhcp server rather than the pool of intellectual property.  When I use the command IP pool everything works fine, but when I use the dhcp command I get an error on the client-side saying that no address private IP was affected by the peer.

  Here is my config.

  connection of AAA VPNCLIENT_AUTHEN group local RADIUS authentication

  local VPNCLIENT_AUTHOR AAA authorization network

  Configuration group customer isakmp crypto VPNCLIENT_GROUP

  xxxxxxxxxxxxxxxxxxxxxxxxxx key

  DNS 172.25.128.43 172.25.65.43

  win 172.25.1.54

  sktnhr.ca field

  172.25.0.27 DHCP server

  GIADDR DHCP 172.25.205.1

  DHCP timeout 10

  pool # VPNCLIENT_IPPOOL

  Crypto isakmp ISAKMP_PROFILE profile

  VRF HUB_VRF

  match of group identity VPNCLIENT_GROUP

  list of authentication of client VPNCLIENT_AUTHEN

  VPNCLIENT_AUTHOR of ISAKMP authorization list.

  client configuration address respond

  crypto dynamic-map DYN_MAP 1020

  game of transformation-ESP-AES-256-SHA

  ISAKMP_PROFILE Set isakmp-profile

  market arriere-route

  card crypto HUB_CRYPTO_MAP 6005-isakmp dynamic ipsec DYN_MAP

  local IP VPNCLIENT_IPPOOL 172.25.205.25 pool 172.25.205.250

  I can see the dhcp request and offer on my dhcp server but nothing is for the customer.  When I use a pool I ping the dhcp server, which makes me think the roads are okay.  Anyone has any ideas.

  You need the giaddr in an EasyVPN server configuration.  Try adding looping to your switch and test it again.  If you use an iVRF, make sure that the closure is in the VRF and the interface to the server.

• VPN client using the certificate self-signed on SAA

  Hello

  I need set up a vpn client that use a certificate automatically generated by the ASA.

  The VPN configuration is easy, especially with the use of the wizard.

  The problem is that I need the procedure to configure the ASA as a CA server and how to send the certificate to the client

  Thank you

  Just to let you know, the ASA can act as a CA server for authentication of cert based for ipsec vpn. It is only possible for sslvpn. So in your case, the client should be the AnyConnect client.

• 506th PIX VPN CAAN connect, but no LAN

  Heelo, we have a 506E with 6.3 (3). We want to use Cisco VPN clinet to connect and can do, but cannot ping on the local network or connect to servers... Need help wih configurations because we are novice maybe... Can someone look through the attached config. and see if we have forgotten something... Thank you

  Change your pool outside 192.168.2.0/24.

  IP local pool vpnpool 192.168.x.60 - 192.168.x.63

  Then add an acl of exemption nat for this network.

  access-list sheep permit ip 192.168.2.0 255.255.255.0 255.255.255.0 192.168.x.0

  NAT (inside) 0 access-list sheep

  Then, also change your acl of tunnel from split to reflect the new pool

  permit ip 192.168.2.0 access list SplitTunnel 255.255.255.0 255.255.255.0 192.168.x.0

• Authentication IPsec VPN Client using the digital certificate

  Hello

  Please I need some clarification and help to set up my ASA 5540 with IOS 8.3 x for client certificate authentication remote.

  I have my certificate root from the Microsoft CA, but not quite sure if the steps described in the following cisco Web sites are exactly what I need since the firewall seems to generate the certificate to use.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080930f21.shtml

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a008073b12b.shtml

  My setup is such that the CA will issue certificates to remote clients and the ASA firewall, and remote clients will authenticate and connect with their certificates which the firewall is constantly updating using the Revocation list updated by the certification authority.

  The dhcp pool must be issued by the DC inside network and not on the firewall.

  Are there any examples or best practices to achieve steps will be really appreciated.

  Thank you

  Hi Josh,.

  Let me explain briefly how Auth PKI:

  In a public key infrastructure configuration, devices trust not each other directly, but they have a certification authority, which is the one who issues the certificate. We call this root CA (there may be a more complex configuration WHERE intermediate are involved, but that's another story). So when the root CA issues a certificate, he signs it with its private key. To be able to verify this signature, we should have the CA public key, which is included with the certification authority.

  So for certificate authentication, you must create a trustpoint, that defines the parameters of the root certification authority.

  Then you will authenticate this trustpoint, which basically means that you will get the certificate of the root CA and store locally.

  After that, you sign up to this CA, which means that you will ask for (and get) your own certificate.

  Other users will do the same and have the same root CA Cert, but different personal (identity) certificates.

  So what happens on authentication is that both ends send their certificate to the other, and they will use the public key contained in the root CA to validate the signature of the certificate received from the remote peer. If the signature is correct, this means that the certificate authority root actually issued the certificate, and this remote peer can be trusted (or not)

  Hope this is clear.

• What are the ports used by the Cisco VPN Client?

  Hello

  I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

  I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

  What are the ports used by the Cisco VPN Client?

  Thank you

  You need to open:

  UDP 500

  ESP protocol

  You must also open the UDP 4500 port (if using NAT - T).

  In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

  1. If using IPSec over TCP 10000, then open TCP 10000.

  2. If using IPSec over UDP 10000, open UDP 1000.