6500 IOS router Cisco VPN Client using DHCP no Pool of IP

Similar Questions

• Router Cisco VPN Client 877

  I have install a plate rotating and spoke VPN with communication between the rays, the hub is also able to receive connections from VPN clients using the client VPN Cisco.

  Is there a a way to allow communication to the rays using just the VPN Client connection to the hub?

  Static IP Hub / DMVPN IP 10.0.0.1 / 192.168.1.0 LAN

  Spoke 1 Dynamic Ip / 10.0.0.2 DMVPN IP / LAN 192.168.5.0

  Spoke an IP Dynamics 2 / DMVPN IP 10.0.0.3 / 192.168.4.0 LAN

  Spoke an IP Dynamics 3 / 10.0.0.4 DMVPN IP / LAN 192.168.2.0

  The tunnels are running with the communication between the spokes.

  No matter what pointer is welcomed more of

  Thank you

  Hello

  To get this working, you need to add pool VPN client to your ACL cryto on each of the rays.

  For example, if your pool is 192.168.6.0 on RADIUS 1, you must add 192.168.5.0 to 192.168.6.0 permits.

  Also make sure you add denys corresponding in the NAT ACL of rays if you NAT. also if you use split tunneling for VPN clients you need to all your subnets of rays in this ACL too. If you do not use the split tunneling, then you should not need to add anything on the client configuration.

  I hope this helps.

  Luis Raga

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• IOS VPN will not respond to connections Cisco VPN Client.

  Hi all

  I'll put my routers fire here.

  I have two 2921 SRI both with licenses of security concerning leased lines separated. I configured one to accept our workers to remote Client VPN Cisco VPN connections.

  I have followed the set up process I used on another site with a router 1841/s and the same customers and I have also checked against the config given in the last guide of IOS15 EasyVPN.

  With debugs all assets, all I see is

  038062: 14:03:04.519 Dec 8: ISAKMP (0): received x.y.z.z dport-60225 Global (N) SA NEW 500 sport package
  038063: 14:03:04.519 Dec 8: ISAKMP: created a struct peer x.y.z.z, peer port 60225
  038064: 14:03:04.519 Dec 8: ISAKMP: new position created post = 0x3972090C peer_handle = 0x8001D881
  038065: 14:03:04.523 Dec 8: ISAKMP: lock struct 0x3972090C, refcount 1 to peer crypto_isakmp_process_block
  038066: 14:03:04.523 Dec 8: ISAKMP: (0): client setting Configuration parameters 3E156D70
  038067: 14:03:10.027 Dec 8: ISAKMP (0): packet received x.y.z.z dport 500 sport 60225 Global (R) MM_NO_STATE

  Here is the abbreviated config.

  System image file is "flash0:c2900 - universalk9-mz.» Spa. 154 - 1.T1.bin.

  AAA new-model
  !
  !
  AAA authentication login default local
  local VPNAUTH AAA authentication login
  AAA authorization exec default local
  local authorization AAA VPN network
  !
  !
  !
  !
  !
  AAA - the id of the joint session

  crypto ISAKMP policy 10
  BA aes
  preshared authentication
  Group 14

  ISAKMP crypto group configuration of VPN client
  key ****-****-****-****
  DNS 192.168.177.207 192.168.177.3
  xxx.local field
  pool VPNADDRESSES
  ACL REVERSEROUTE

  Crypto ipsec transform-set aes - esp esp-sha-hmac HASH
  tunnel mode

  Profile of crypto ipsec IPSECPROFILE
  the HASH transform-set value

  dynamic-map crypto VPN 1
  the HASH transform-set value
  market arriere-route
  !
  !
  list of authentication of card crypto client VPN VPNAUTH
  card crypto VPN VPN isakmp authorization list
  crypto map VPN client configuration address respond
  card crypto 65535-isakmp dynamic VPN ipsec VPN
  !
  !
  local IP VPNADDRESSES 172.16.198.16 pool 172.16.198.31

  REVERSEROUTE extended IP access list
  IP 192.168.0.0 allow 0.0.255.255 everything
  Licensing ip 10.0.0.0 0.0.0.255 any

  scope of IP-FIREWALL access list
  2 allow any host a.b.c.d eq non500-isakmp udp
  3 allow any host a.b.c.d eq isakmp udp
  4 ahp permits any host a.b.c.d
  5 esp of the permit any host a.b.c.d

  If anyone can see anything wrong, I would be very happy and it would save the destruction of a seemingly innocent router.

  Thank you

  Paul

  > I would be so happy and it would save the destruction of a seemingly innocent router.

  No, which won't work! But instead of destroying the router, I can do it for you. Just send it to me... ;-)

  OK, now more serious...

  1. The default Cisco IPSec client uses only DH group 2, while you set up the 14. Try to use Group 2 in your isakmp policy.
  2. You have your virtual model in place? She is not in the config.

• Using Cisco VPN Client VPN

  Is it possible to use a private network virtual created with the WRVS4400N router with VPN Client from Cisco Systems (ver 5) software? (Although QuickVPN works very well.)

  Is it possible to use with Account customer VPN mode? Or is it possible to use with IPSec VPN (Tunnel) mode? If so, please provide together how to client-side and the router. Thank you!

  Unfortunately Small Business routers are not compatible with the Cisco VPN Clients. The Cisco VPN Clients have more parameters that are not available in the materials of the series of small businesses, so all we can use is the application of QVPN.

• IPSec site to site VPN cisco VPN client routing problem and

  Hello

  I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

  The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

  There are on the shelves, there is no material used cisco - routers DLINK.

  Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

  Can someone help me please?

  Thank you

  Peter

  RAYS - not cisco devices / another provider

  Cisco 1841 HSEC HUB:

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key x xx address no.-xauth

  !

  the group x crypto isakmp client configuration

  x key

  pool vpnclientpool

  ACL 190

  include-local-lan

  !

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

  !

  Crypto-map dynamic dynmap 10

  Set transform-set 1cisco

  !

  card crypto ETH0 client authentication list userauthen

  card crypto isakmp authorization list groupauthor ETH0

  client configuration address card crypto ETH0 answer

  ETH0 1 ipsec-isakmp crypto map

  set peer x

  Set transform-set 1cisco

  PFS group2 Set

  match address 180

  card ETH0 10-isakmp ipsec crypto dynamic dynmap

  !

  !

  interface FastEthernet0/1

  Description $ES_WAN$

  card crypto ETH0

  !

  IP local pool vpnclientpool 192.168.200.100 192.168.200.150

  !

  !

  overload of IP nat inside source list LOCAL interface FastEthernet0/1

  !

  IP access-list extended LOCAL

  deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  IP 192.168.7.0 allow 0.0.0.255 any

  !

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  !

  How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

  Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

  DE:

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

  TO:

  access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

  Also change the ACL 190 split tunnel:

  DE:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

  TO:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

  Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

  Hope that helps.

• Cisco VPN Client 2801 router

  Hello

  I installed a router cisco 2801 to accept vpn connections, I use the cisco vpn client and the tunnel is created and is being created of the its.

  However, I cannot ping my vlan (only those who have a nat inside the ACL, those who have not said I can ping), so I have a NAT problem, just don't know where.

  Heres part of my setup on the ACL,

  IP local pool ippool 192.168.100.10 192.168.100.100

  by default-gateway IP X.X.X.X (ISP GATEWAY)

  IP forward-Protocol ND

  IP http server

  no ip http secure server

  IP http flash path:

  !

  !

  IP nat inside source list 1 interface FastEthernet0/1 overload

  IP nat inside source list 2 interface FastEthernet0/1 overload

  IP nat inside source list 3 interface FastEthernet0/1 overload

  IP nat inside source list 6 interface FastEthernet0/1 overload

  overload of IP nat inside source list 20 interface FastEthernet0/1

  IP nat inside source map route SHEEP interface FastEthernet0/1 overload

  IP route 0.0.0.0 0.0.0.0 X.X.X.X (external IP)

  Route IP 192.168.10.0 255.255.255.0 192.168.90.2

  IP route 192.168.20.0 255.255.255.0 192.168.90.2

  IP route 192.168.30.0 255.255.255.0 192.168.90.2

  IP route 192.168.40.0 255.255.255.0 192.168.90.2

  IP route 192.168.50.0 255.255.255.0 192.168.90.2

  IP route 192.168.60.0 255.255.255.0 192.168.90.2

  IP route 192.168.200.0 255.255.255.0 192.168.90.2

  !

  NAT extended IP access list

  deny ip 192.168.10.0 0.0.0.255 192.168.100.0 0.0.0.255

  deny ip 192.168.20.0 0.0.0.255 192.168.100.0 0.0.0.255

  deny ip 192.168.30.0 0.0.0.255 192.168.100.0 0.0.0.255

  deny ip 192.168.60.0 0.0.0.255 192.168.100.0 0.0.0.255

  deny ip 192.168.90.0 0.0.0.255 192.168.100.0 0.0.0.255

  permit ip 192.168.10.0 0.0.0.255 any

  ip licensing 192.168.20.0 0.0.0.255 any

  IP 192.168.30.0 allow 0.0.0.255 any

  IP 192.168.60.0 allow 0.0.0.255 any

  IP 192.168.90.0 allow 0.0.0.255 any

  !

  access-list 1 permit 192.168.90.0 0.0.0.255

  access-list 2 allow to 192.168.10.0 0.0.0.255

  access-list 3 allow 192.168.30.0 0.0.0.255

  access-list 6 permit 192.168.60.0 0.0.0.255

  access-list 20 allow 192.168.200.0 0.0.0.255

  !

  SHEEP allowed 10 route map

  corresponds to the IP NAT

  !

  The 192.168.90.2 address is my switch L3 (Cisco 3750)

  Any pointer is more than welcome,

  Concerning

  Miranda,

  Have you tried to remove the following lines:

  IP nat inside source list 1 interface FastEthernet0/1 overload

  IP nat inside source list 2 interface FastEthernet0/1 overload

  IP nat inside source list 3 interface FastEthernet0/1 overload

  IP nat inside source list 6 interface FastEthernet0/1 overload

  overload of IP nat inside source list 20 interface FastEthernet0/1

  And simply let this one:

  IP nat inside source map route SHEEP interface FastEthernet0/1 overload

  ?

  I have all the neceary allowed in the ACL of NAT, so you do not have individual lines for each network.

  Also, I noticed that your ACL 20 reads

  access-list 20 allow 192.168.200.0 0.0.0.255

  But your NAT ACL bed

  ip licensing 192.168.20.0 0.0.0.255 any

  I think you have a typo in there, you have a 200 on 20 and on the other.

  Check it out and let me know how it goes. Don't forget to clear the NAT table after deleting these lines:

  clear the ip nat trans *.

  I hope this helps!

  Raga

• Using Cisco VPN Client in Windows 7 Professional 64 bit

  Hi all!
  I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem

  Open the XP VM itself, do not use the shortcut that was published in
  the W7 boot menu. You need to install Outlook / your email client
  Inside the virtual machine, as well as on the side of W7. You can point to the same
  PST files if you have local PST files, but you just can't open them in
  at the same time of W7 and XP VM.

  There is no way to bridge using the shortcut of publishing app

  Some people have reported success with the third party IPSec
  replacements as customer universal shrew or the NCP. Your IT Department.
  would like to know if these are supported

  :

  > Hello all! I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem
  Barb Bowman www.digitalmediaphile.com

• Different classes using Cisco VPN Client VPN

  Hello

  on a cisco ASA 5510, I defined a vpn group used for remote teleworkers who have access to the entire LAN using Cisco VPN Client 4.8.

  I would give to others of this client, but I need to limit their access to LAN resources, which means that I have to have two types of users:

  Remote LAN access

  access to only certain IP addresses

  Both must use the Cisco VPN client.

  How can I do?

  Thank you

  This link should help.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a0080641a52.shtml

• PIX: Cisco VPN Client connects but no routing

  Hello

  We have a Cisco PIX 515 with software 7.1 (2). He accepts Cisco VPN Client connections with no problems, but no routing does to internal networks directly connected to the PIX. For example, my PC is affected by the IP 172.16.2.57 and then ping does not respond to internal Windows server 172.16.0.12 or trying to RDP. The most irritating thing is that these attempts are recorded in the system log, but always ended with "SYN timeout", as follows:

  2009-01-06 23:23:01 Local4.Info 217.15.42.214% 302013-6-PIX: built 3315917 for incoming TCP connections (172.16.2.57/1283) outside:172.16.2.57/1283 inside: ALAI2 / 3389 (ALAI2/3389)

  2009-01-06 23:23:31 Local4.Info 217.15.42.214% 302014-6-PIX: TCP connection disassembly 3315917 for outside:172.16.2.57/1283 inside: ALAI2 / 3389 duration 0:00:30 bytes 0 SYN Timeout

  2009-01-06 23:23:31 Local4.Debug 217.15.42.214% 7-PIX-609002: duration of disassembly-outside local host: 172.16.2.57 0:00:30

  We tried to activate and deactivate "nat-control", "permit same-security-traffic inter-interface" and "permit same-security-traffic intra-interface", but the results are the same: the VPN connection is successfully established, but remote clients cannot reach the internal servers.

  I enclose the training concerned in order to understand the problem:

  interface Ethernet0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP address xx.yy.zz.tt 255.255.255.240

  !

  interface Ethernet1

  nameif inside

  security-level 100

  172.16.0.1 IP address 255.255.255.0

  !

  access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.2.56 255.255.255.248

  !

  access extensive list ip 172.16.0.0 outside_cryptomap_dyn_20 allow 255.255.255.0 172.16.2.56 255.255.255.248

  !

  VPN_client_group_splitTunnelAcl list standard access allowed 172.16.0.0 255.255.255.0

  !

  IP local pool pool_vpn_clientes 172.16.2.57 - 172.16.2.62 mask 255.255.255.248

  !

  NAT-control

  Global xx.yy.zz.tt 12 (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 12 172.16.0.12 255.255.255.255

  !

  internal VPN_clientes group strategy

  attributes of Group Policy VPN_clientes

  xxyyzz.NET value by default-field

  internal VPN_client_group group strategy

  attributes of Group Policy VPN_client_group

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list VPN_client_group_splitTunnelAcl

  xxyyzz.local value by default-field

  !

  I join all the details of the cryptographic algorithms because the VPN is successfully completed, as I said at the beginning. In addition, routing tables are irrelevant in my opinion, because the inaccessible hosts are directly connected to the internal LAN of the PIX 515.

  Thank you very much.

  can you confirm asa have NAT traversal allow otherwise, activate it in asa and vpn clients try again.

  PIX / ASA 7.1 and earlier versions

  PIX (config) #isakmp nat-traversal 20

  PIX / ASA 7.2 (1) and later versions

  PIX (config) #crypto isakmp nat-traversal 20

• Unable to connect using the Cisco VPN client

  Hi all. I recently configured a 5510 ASA to allow remote access using the Cisco VPN client. The problem is that everything works fine when I connect using a modem classic or on a computer with a public address that I use for testing purposes, but whenever I try to connect with on an ADSL line, I can't access to the resources. I have connection and after that nothing, I can not achieve anything.

  I enclose the relevant configuration information in the attachment. Any help is welcome.

  Depending on the version, add...

  ISAKMP nat-traversal

  or

  ISAKMP nat-traversal crypto

  Should be all you need.

• How to use Windows 7 64-bit cisco vpn client?

  Hello

  I want to use the cisco vpn client to connect to my Institute.

  I use Windows 7 64-bit edition Home premium.

  I tried several options, but nothing has worked.

  Please suggest me the correct procedure to run on my Windows 7 64 bit Home Premium Cisco vpn client.

  Thanks in advance,

  Federico

  VPNclient is not yet supported on 64-bit windows.

  However, there is a beta version of the next 5.0.7 version that does.

  Have you tried this version? If so, what are the exact symptoms?

  Edit: you can download the 5.0.7 beta here

• What are the ports used by the Cisco VPN Client?

  Hello

  I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

  I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

  What are the ports used by the Cisco VPN Client?

  Thank you

  You need to open:

  UDP 500

  ESP protocol

  You must also open the UDP 4500 port (if using NAT - T).

  In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

  1. If using IPSec over TCP 10000, then open TCP 10000.

  2. If using IPSec over UDP 10000, open UDP 1000.

• Slow initial connection using Cisco VPN Client

  I am currently using Cisco VPN Client v5.0.07.0290.  Whenever I start my connection, it takes me about 90 seconds for the prompt to display authentication and another ~ 90 seconds to finish the auth. and connect successfully.  I have another computer laptop w / the same WIN7 OS and version of Cisco VPN Client and he ends the connection to<30 sec. ="" why="" is="" this? ="" any="" suggestions="">

  Hi Sergio,

  You import the .pcf for the VPN Client file? If so, please try to recreate a new file .pcf locally on the machine itself and try to connect. Let me know how it goes.

  Thank you

  Delvallée

• Cannot use Cisco vpn client

  Dear all,

  I have cisco vpn client v5.0.05.

  1 / when I lunch the customer, it connect to the asa, so I can't reach the network behind my ASA

  2 / when connected to the vpn client, I can not use my access to the internet, I configured splitunnel, but does not.

  3 / sometimes, cisco vpn client disable my network ip of the gateway card.

  Please, can someone help me?

  Concerning

  Can you please share the configuration of the SAA. There is no specific configuration that must be done on the vpn client.