3ware 9550SXU - 16ML compatibility with WHS 2011 RAID controller. Need info pilot.

Similar Questions

• OptiPlex 3010 with third-party RAID controller

  Hello

  I installed an Adaptec RAID 1220SA controller in an Optiplex 3010 and contains two HARD drives in the annex. It is not all disks connected directly to the motherboard. The RAID card, or readers connected to it are visible in the BIOS, so they cannot be selected as boot devices.

  The machine starts OK, past through the initialization of the controller RAID OK, but then it stops with a 'no hard drives detected' attention, giving 3 choices: continue, go to the bios, go to the automatic test utility.

  However, if (continued) F1 is pressed, it starts perfectly among the RAID drives and everything works as expected.

  Any ideas how to get rid of this error/warning message?

  Hi nehamanoka,

  I got the same problem as you, only with an Optiplex 7010 and also an Adaptec 1220SA and a Promise Fasttrak TX 2300 raid controller.
  (press F1 to continue...)

  I also tried a lot of things and my 7010, she collaborates with the following parameters of the BIOS (Dell):

  General - startup sequence: drive HARD internal
  System - integrated NIC configuration: enabled w/PXE

  I have no idea why it works now and I had no problem with a 790 Optiplex.

  HTH

• PowerEdge 2800 with 4/Di Raid Controller

  I lost inadvertently communication on my hard drive for the OS and Raid 5 data readers.  Currently I can not start the server and need assistance in getting to the top.  I installed 3 new drives to set up a backup and during the process, I've dethroned poor readers.  How can I determine which is the main OS drive and who are the 3 logical drives that are the data reader.  I guess I have to tell the server which drive is the boot drive, but a little shy gun now after this experience.

  Thank you

  Steve

  "I do my best to ensure that the information provided is accurate and I am very confident that it is."

  I believe you, but information is no not any sense, as planned.

  "I work from my phone and do not have Internet access to perform the procedure requested right now."

  It is perhaps the only way to get it online.

  "As long as the battery is concerned, I was told that when the battery is only one branch that it will release the current configuration and start cut line."

  It will not.  The RAID configuration is stored in a NON VOLATILE memory.  Disconnect the battery will clear the memory VOLATILE of the controller, which is used only for write cache.

  "Regarding the location of the reader, what the raid controller tells me.

  Just to clarify: the system EACH time it starts, when the charge controller, that none of the logical drives are found?  And there is no message indicating how you choose/use/save a configuration do not match?

  If you know disk 9 is your RAID 0, you can try power off, removal of all readers (hold that which), insert the diskette 9 on the slot 0, then start CTRL-m, configure, view/Add... If you are prompted to choose between the drives and the NVRAM, choose drive, then save to the output and try to start the operating system.

  If it does not, I would start thinking about data recovery or restore from a backup.

• Get the error failing wmpnetwk.exe with WHS 2011 application

  I had problems with the windows media player network service on my windows home server machine. Continually, I get the following error:

  Name of the failing application: wmpnetwk.exe, version: 12.0.7601.17514

  The failed module name: ntdll.dll, version: 6.1.7601.18247

  Exception code: 0xc0000374

  Offset of vulnerabilities: 0x000000000000c4102

  ID of the process failed: 0x149c

  The failing application path: C:\Program Files\Windows Media Player\wmpnetwk.exe

  Path of the failing module: C:\Windows|system32\ntdll.dll

  (I think) as a result, I can't successfully access my home server to my Xbox 360, or new certified DLNA Samsung Blu - ray player.

  I tried running sfc/scannow and it finds no problems. I checked the service has started and is configured to start automatically on startup. I restarted the server.

  Help!

  Hello

  We have a dedicated support team that will help you solve the problems on the Windows Home Server platform. Check out the link to post the same query:

  https://social.Microsoft.com/forums/en-us/home?category=WindowsHomeServer

  Please let us know if you need any other assistance on Windows.

• Compatibility with Windows 7 64-bit, need monitor driver Acer G185H LCD 18.5 "monitor

  I installed the softwared drive and that doesn't change.  The camera has always I have a generic Viewer and does not list the brand name

  According to Acer site pilot is win7 64 bit compatible

  http://support.Acer.com/us/en/product/default.aspx?modelId=2046

  The name of the monitor is not allways listed when you view the properties of the device, but is the default resolution, the value of this device?

• Areca 1882IX PCIE 3.0 Raid Controller - need help

  I'm extremely frustrated!   I installed my new Areca Raid card and can't make it work!

  First of all, has been the question of creating a driver diskette.   After hassling with tools for two hours, I finally found an old floppy drive and installed on my system.  It worked finally.

  Then when I tried to install the driver, firstly it doesn't seem to install it.  I clicked on the tab + F6 during startup and, apparently, that didn't do anything.  However, it seemed he installed something.   Windows 7/64 blue armored constantly until I restored it to an earlier version.   I went through this installation bluescreen process twice!

  Anyone knows tricks to make this card raid work?   Do not forget that this version PCIE 3.0, not 2.0.   Is this card ready for prime time?

  If this thing does not work, is there other quality controllers will work?

  Thank you

  Dan.

  Dan,

  Since I live in a country late, I always wait the availability of version 3.0 PCIe. The consequence is that I have no experience with this specific map, but the message:

  F/W detected: * SDRAM don't speed not enough *!

  is irregular enough to suspect that the RAM cache is not properly installed or is defective. You can check that the module is well rigged? Otherwise I would support Areca contact. In general, they respond quickly and are very useful.

• Upgrade 2 T110 S300-based hardware RAID controller

  I have a Power Edge T110 2 provided with a PERC S300 SAS controller attached to 6 internal drives and execution of Win2008R2. I'm about to rebuild the tower as well as a Ubuntu Linux server and need to change the S300 with something that is hardware RAID. I'm looking to the PERC H200 as substitute, however I have a few problems.

  Mainly, the H200 seems to have internal mini SAS 26 pins, while the S300 has 32 large internal regular PIN. Would normally not be a problem, but the T110 also shipped with a certain type of cable combo, which integrates the internal Rod 32 with for each of the four HDDs that it can reach the food.
  In addition, it seems that this combo cable is integrated on the power supply.
  I need to understand what the card can I use to replace my software RAID controller with a hardware RAID controller and always use the combo cable OR how can I replace the cable with the new card.
  Thank you!

  Part number 342-3389 includes the necessary cables.

• T130 PowerEdge RAID controller onboard or get a card?

  Finally, we got a budget to replace our entire PoS system and got a PowerEdge T130 to replace our T110. What I'm not clear on the RAID controller embedded - is it only the software, hardware or some hybrids; and what are the levels of RAID support? The existing facility is with SATA AHCI and RAID1 controllers in Windows Server 2008 R2 value.

  Our range of SSD in our existing server still in excellent condition, so I want to migrate it on when I'm done configures OS and PoS software. Should I go into BIOS, set up the RAID controller and see what levels he'll give me or I'd better use the physical map of the T110 in the T130? The T110 is currently using a PERC S300 card with 4 SSD in RAID10. Alternatively, can anyone point me to a better RAID card for this server which would do well to RAID10? I shortly before the system goes into the production environment, so I want to change my hardware now while I still can.

  It is only the second build of the full server that I have used in the past 6 years. Would like to hear the thoughts of anyone T130, RAID, etc. Finally, moving into the world of 64-bit, thank God.

  htc2010

  Finally, moving into the world of 64-bit, thank God.

  Welcome to 2009! (Sorry, I understand the difficulties from old tech in some organizations, I do).

  htc2010

  Finally, we got a budget to replace our entire PoS system and got a PowerEdge T130 to replace our T110. What I'm not clear on the RAID controller embedded - is it only the software, hardware or some hybrids; and what are the levels of RAID support?

  Software only - it is based on the Intel RAID chipset and supports RAID levels 0, 1, 5, 10 volumes and non-RAID. It should be avoided.

  htc2010

  The existing facility is with SATA AHCI and RAID1 controllers in Windows Server 2008 R2 value.

  This is what should be done with the integrated RAID controller (S130 - off and mirrored in the operating system instead - IF hardware RAID, which is preferable, is not checked).

  htc2010

  Should I go into the BIOS, change the RAID controller and see what levels he will give me

  Still once, I you would recommend against the use of the S130, AND you can't replace non-RAID RAID on the fly. It would require reinstallation or backup/restore.

  htc2010

  or I'd better use the physical map of the T110 in the T130? The T110 is currently using a PERC S300 card with 4 SSD in RAID10. Alternatively, can anyone point me to a better RAID card for this server which would do well to RAID10?

  The S300, while only slightly better than the S130, is not supported in the T130. I would recommend the H730 or the H330 if you absolutely cannot spend the money for the H730 (they are cheaper suppliers that Dell directly). The two become RAID 10. The H330 will give you about the performance of your S300. If none of them are selected, I'd go with what you vascular (the S130 is your only other option 'supported', and it's garbage). If this system is heavily used, I highly recommend, but if the H730 moderately or less software RAID is fine (you have SSD in the new configuration, I take it...).

• WHS 2011 dashboard closes unexpectedly with "Safe Mode Settings (found Suspects) - list of suspect supplements: Home - manage the start-up...» »

  1. I've been running WHS 2011 successfully for a few weeks, 6 on an i5 with 8 GB of memory (only currently installed by computer Client is an Acer 5750 i7 with computer laptop 4 GB memory). but have had some unexplained cases of the dashboard suddenly closing.  The above title is explicit enough to completely describe the issue. (Snip available)
  2. View later "Mode settings safe - all the add-ins ' server help/Safe Mode confirms that the integrated add-in is v6.1.8800.16399. (Snip available)
  3. Inspection of all categories of relevant event viewer shows no error/warning etc. near or at the time, or even the date of the failure.
  4. As the Windows updates are underway for both Server & Client, I can only deduce that it is a mistake in WHS 2011 or add-on integrated hospitality who received an automatic diagnosis, or an error in the detection mechanism.
  5. This behavior seems to occur when I switch to the WHS 2011 Home tab from another server or activity customer.
  6. Please Microsoft will investigate the matter and correct if necessary.

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• WHS 2011 Media - Web remote access - a problem with the media of files appearing not

  I'm running WHS 2011.  When I connect via a remote web access and media sharing is turned on, I can see the three categories in the window 'Library' - 'Browse images', 'Browse music' and "browse videos".  I have several songs in the "ServerFolders\Music" folder on the server and I used to see the album art in the home screen remote Web access under 'Browse music. "  Now, the icon 'Browse music' on the screen of remote access Web says "0 songs" even if I have not moved or removed all the songs in the folder ServerFolders\Music on the WHS machine.  If I go to the "Shared folders" window and open the 'Music' it on access web remote, all the music files are listed as expected.

  I don't know how to reset or refresh the window "Multimedia library" in order to recognize the music files I have on the server.

  Please advise...

  Thank you for your help.

  Hello

  You can publish your application in the Windows Home server to improve the assistance:
  http://social.Microsoft.com/forums/is/whs2011/threads

• WHS 2011 OEM with HP Proliant Microserver license will not activate

  I'm building a new Server OEM WHS 2011, using HP Proliant Microserver.   I first installed one a box, entered the serial number, I get an invalid serial number message, even though I know that I entered the number is correct.

  Any suggestions are greatly appreciated.

  Hello Miked53,

  You can find Windows Home Server forums at the following location. I suggest you re-post your question here:
  http://social.Microsoft.com/forums/en-us/category/WindowsHomeServer/

• WHS 2011 SAS hard drives showing up as removable media

  I have a WHS 2011, I built and with it, I installed 5 SAS 1 TB hard drives each and they are connected to a dell sas raid controller SAS6/ir, after research in disk management to try to make a new split volume a disc appears only four make their appearance as a removable media , and I can't use an any of them.

  Hi Stevensample,

  Given that the problem is related to Windows Home Server 2011, you must validate your application in the Windows Home Server Forum to get help.

  Windows Home Server Forum

• Why whs 2011 installation gets stuck to copy Windows files on the HARD drive?

  I try to install WHS 2011 OEM on a HP EX470 software.  I have tried about 30 times without supervision and welfare facilities in the past 4 months and am very frustrated that I can't succeed and purchase the software was a waste of time and money.  I tried 4 hard drives, properly formatted capacity of 250 GB to 2 TB.  EX470 has the original 1620 AMD processor and 2 GB RAM upgraded and qualifies for the upgrade to a 64-bit system.

  Problem with installation assistance tries: Installation says "Copying Windows files", but after a variable time in hours of waiting, growth remains at 0% and finally says "error in installation.  Try to restart the installation.  Same thing happens with the help of the DVD, or by using a Sandisk Cruser formatted and made bootable 16 GB flash drive with a file cfg.ini the instructions online and also tried without the cfg.ini file.
  Problem with unattended installation attempts:  Process completely blind.  Does not install even if left for 24 hours.  Cannot decipher the flashing lights on the Flash drive and thereafter, no installation nor evidence of partial installation is visible on check the hard drive on another computer.  I suppose that the same thing as the installation attempts assisted.
  Looked for solutions online for 4 months, but nobody does the problem of Windows not to copy the files to the HARD disk during installation and what goes wrong.
  Help!

  Hello

  I suggest you post your question to the link and check.

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

• I can restore the backup made by WHS v1. PP3 the WHS 2011? Or do I need to copy the files over the network of old serevr again?

  WHS backup

  You just bought a new WHS 2011. Question, can I restore the backup made by WHS v1. PP3 the WHS 2011?  Or do I need to copy the files over the network of old serevr again?

  Hello

  Because the problem is with Windows Home Server, I recommend you post this question in the Forums Windows Home Server.

• SSD compatibility w/PERC S300 RAID?

  We have an old PE T110 first generation with a PERC S300 RAID controller and 4x250GB drives. However, because the controller is older, there isn't much documentation about SSD compatibility. Does anyone at - he had success the upgrade of any server/workstation using a PERC S300 with an SSD of any kind in a RAID 10 configuration?

  Finally, I don't remember what type of connector is on the existing disks and am a little confused about the difference between SATA and SAS. What normally comes stock with this system and which would need if I moved to SSD? New cables? Anything else I need to know?

  htc2010

  is it not reasonable to assume I could just as easily swap on each drive in the Bay, one at a time, with a SSD?

  You cannot mix SAS and SATA drives in the same array. Also, you cannot mix HDD and SSD. If SSD does not support the S300, then he cannot know the difference between a SATA SSD and a SATA HDD, so it can work, but 1) I wouldn't rely on it and 2) just know that real RAID controllers, it can be done.

  In the end, I don't know if she will achieve your goals. The reason why I asked is because you could just add the SSD as a new VD, then move the files of database, etc. on to improve the speed, but it sounds like a lot of work for little return. I just invest in a backup recovery solution, good. If it can work in a virtual environment?