4700 c: cannot connect my 4700 PSC Internet

Similar Questions

• Color LaserJet MFP M277dw Pro: Cannot connect LaserJet MFP M277dw Internet

  My printer is installed and I can print from three computers (Windows 7 and 64-bit Windows of 8.1).  I can also AirPrint from my iPhone.

  When I install all software configuration and the driver, when it gets to a point where she wants to register the printer, I get an error message that the printer cannot connect to internet.

  I can get to the control page of printer through the IP address of computers.

  However, when I go to the web services tab, click Activate, it tries to connect, but then I get "connection error. Check the Internet connection. "All the other devices on my network can access the internet without problem.  Because I can not connect, I can also not the code to activate the connected HP web services.

  I tried with the printer connected via radio (via my wireless router very new and directly through the router broadband wireless access), as well as with a wired connection.

  Everything seems to work, except that the printer cannot make an Internet connection.

  That did not work.  Here's what I did, what worked:

  Reset the default printer.

  Turn off the router, printer, and then click computer.

  Restart rounter, then printer and computer.

  Set the lan cable for printer (rather than wireless configuration)

  The printer has obtained an ip address.

  Ran the application "you reconfigure HP printer" in the folder of the software hp (Windows 7 drivers).

  After that, I don't seem to have problems.

• I can't connect to internet unless I'm using an ethernet cable. I am on a computer laptop lenovo and cannot connect to my home internet group. When I troubleshoot, my device is not found. What should I do?

  My computer now has internet but my laptop cannot get any internet without ethernet cable. When I troubleshoot, my device is also unrecognisable.

  Hello

  1. who troubleshoot steps did you try?

  2 did you change on your computer?

  Method 1:

  I suggest you to see link and check.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  I also suggest you to see link and check.

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Troubleshoot low wireless signal quality

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-low-wireless-signal-quality-problems

• Cannot connect printer to the internet for instant ink service

  Installed Flash cartridges for the first time to my printer Officejet Pro 8610. The printer prints very well, but it is not connected to the internet by message on the printer screen. I checked the connection to the wireless router and it is connected correctly. I can also print from my remote legacy, iPhone, iPad, etc. "When I try to connect to the internet the printer, I get the following message appears on the printer screen.

  "Update conflict

  Web services and the HP printing software are updated on the computer or the built-in webserver (EWS). Wait for the update to finish and then try again. »

  When I go on the 'connected' site, it shows the registered pronter but it shows that the printer is "offline". When I try to update, nothing happens.

  Thank you very much. Worked the first time.

  Steve Raimondi

  happytohelp01 wrote:

  Hi @sraimondi,

  Welcome to the Forums of HP's Support.  I see that you get an error message of connection on your printer Officejet 8610.

  Please define Manual of the printer an IP address manually and DNS servers.  I've included a link to another post which has the steps with screenshots on how to do it.

  Please let me know the results.

• my laptop cannot connect wirelessly to the internet with the built-in wireless adapter

  G50-118NR my client specification identifies my network home qwest DSL WPA2 as public wireless whenever I connect wireless using the Atheros AR5007 802 wireless network adapter. 11 b / g WiFi and does not connect to the internet.  I can change the Private type, but it does not help.  I have restored the laptop using Vista Home Prem 32-bit recovery CD and that did not help.   The wired connection works perfectly and other 'g' and 'n' USB wireless adapters also work very well.

  Hello:

  Please read my post on the link below for the Atheros cards and newer routers, and see if you install the latest Atheros driver I posted on it works for you.

  http://h30434.www3.HP.com/T5/wireless-Internet-home/Atheros-WLAN-driver-fixes-connection-issues-with-many-new/TD-p/701407

  Paul

• Cannot connect on CC, no internet connection

  I installed CC on a new machine and install CC with my connection to Adobe that has members for CC. The login window says "please connect to the internet and try again", although it works and should be fine.

  Use any type of firewall software that could have an impact on the creative cloud desktop application to connect?  I recommend you review the steps in the sign, activation, or connection errors. CC, CS6, CS5.5

  Log, activation, or connection errors. CS5.5 and later versions

• Cannot connect Tecra M10 to the Internet

  My wife has a TecraM10 with an Intel 82567LM gigabit wired network adapter. It cannot connect to the Internet via either wired LAN by plugging directly into the container of Cat 5 to the rear of the machine or the thorugh a docking station.

  A diagnosis indicates that the LAN switch is turned off and check the manual as to his location to turn it on.

  I can't find a reference to a LAN switch in the manual. I checked TCP/IP protocols and they progress ste correctly and the device manager says it's working properly.

  Any ideas? Thank you. John

  Hello John

  Card LAN installed and listed correctly in the Device Manager?
  >... LAN switch is off
  Laptops doesn t have LAN switch. WLAN spend only so I t understand how you can get this message.

  Please check device manager first and let me know if the network card is OK here?
  When you connect the LAN cable to your Tecra is green LED ON?

  By the way: did you test connecting to the local network using another PC/computer laptop?

• A Wi - Fi connection does not have an IP address and cannot connect to Internet

  Here's my question:

  "Wi - Fi doesn't have an IP address and cannot connect to Internet"

  But he connects.  I use the model of airport Time Capsule ME182LL/A and the last OS.

  The reason why I suspect the problem is that my Samsung smart TV will not connect to internet, but connects to the WiFi.

  Do I have a problem when the network preferences indicates my network with a point orange and says 'No IP Address'?  It doesn't have a green dot next to the Wi - Fi connection and it says connected.  I'm puzzled.

  Thanks for any idea that you can provide.

  Something wrong with the Setup program.

  After the airport utility screenshots of the configuration of TC.

  In particular this modem do you have? Actual spending brand and model please.

  Who is your ISP?

• Cannot connect Bluray Internet

  Shows the signal from the router but cannot connect

  Hello Ellen,.

  Welcome to the community of Sony.

  Check in the manual of the player, if the LAN USB UWA-BR100 card is needed to connect the player to the wireless network.

  You can download the manual here.

  Test the speed of the Internet being used from the link below.

  http://www.KB.Sony.com/selfservice/documentLink.do?externalId=C1013044

  Internet connection speed minimum of 2.5 Mbps or greater is required for streaming of videos from standard definition (SD) and 10 Mbps or higher is required for high definition (HD) videos.

  Follow the steps mentioned below to resolve this issue.

  http://www.KB.Sony.com/selfservice/documentLink.do?externalId=C1018338

  If the problem persists, perform the steps on the below knowledge base article to configure the network manually.

  http://www.KB.Sony.com/selfservice/documentLink.do?externalId=C1025439

  If my post answered your question, please mark it as an "accepted Solution".

• Printer cannot connect to Internet

  I need a claim code. To achieve this, I need to access ePrint of my Control Panel on my printer HP model 3512. Unfortunately, I like "Printer cannot connect to the Internet." Can someone help me understand this and correct the problem? Thanks in advance... M

  You don't need a code of request to connect to the internet. Your printer has wifi support? Connect the printer to your router wireless first, then you can access ePrint.

• HP Envy 4500: Printer says it has solid network connection, but cannot connect to the internet

  So I have not been able to use my printer wireless lately, so I decided to check if it was connected to my wireless network. It is; I checked, re-connected and checked several times. So I decided to reactivate my web services. I have them turned off, and now whenever I press the button on the printer ePrint, it says connection for a really long time and then displays the message in the sense of "the printer cannot connect to the server. Check the internet connection and proxy settings.

  I have re-connected the printer to my wireless network, I checked that if I use a proxy server (I'm not), I used the HP print and Scan Doctor - just, it won't just matter what I do.

  All I can think about is the fact that I have recently purchsed a new router, but says that its connected which is what really stem me.

  This printer makes me crazy - please help

  Hi @mastersword64,

  Welcome to the HP community!

  I hope you have a pleasant experience with us.

  I want to help you with the connection error, you get on your e-all-in-one of HP ENVY 4500 printer when you try to enable web services.

  Here are some steps, I suggest trying to get your web services up and running it again:

  Network Power Reset:

  We'll leave the router and unplug the power cable (NOTE: do not reset the router.), and then do the same with the printer and shut down the computer. After a minute, plug in the router, wait to fully turn on, then plug the printer back in and wait for the wireless light become solid. Once the router and the printer are on, go ahead and re - turn on the computer. This will refresh the network connection.

  Restore the default settings of the network and reconnect:

  1. on the front panel of the printer, press your up wireless icon

  2. Select settings.

  3. Select restore default network settings.

  4 turn on your printer.

  5. once it is initialized to save, press the wireless icon again.

  6. Select settings.

  7. Select Wireless Assistant , and then follow the prompts to enter the details of your wireless network.

  8. try to activate the web services again.

  Configure a manual DNS for your printer:

  1 obtain the IP address of your printer

  a. This can be done by pressing the icon on the printer wireless.

  2. Enter the printer's IP address in a browser on your computer.

  3. Select the tab network at the top of the page.

  4. on the left, select network.

  5. Select network address (IP)

  6. Select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  7. Select apply. You can get a warning simply select OK.

  Please reply to let me know if these steps resolve your issue.

  Good luck!

  

• I have a SBS 2011 and cannot connect to internet through VERIZON FIOS.

  I have a SBS 2011 and cannot connect to internet through VERIZON FIOS. The SBS is unable to detect the IP address and gave an error message. I never get to a screen that allows me to type in the "IP address of the router" or "IP address". Verizon told me that their router address is "192.168.1.1". After a new trial, I added my NETGEAR FS105 switch between the FIOS router and my PC 2 and SBS. Result - conflict of addresses of servers.
  Any suggestions or solutions to this problem?

  Thank you
  Chuck

  Hi Chuck

  Your question is addressed in the Microsoft Answers forums.

  Please ask your question in the following forum.

  Small Business Server Forum:

  http://social.technet.Microsoft.com/forums/en-us/smallbusinessserver/threads

  Concerning

• Cannot connect to internet after Windows updates

  When I double click on broadband connection, it won't open after installing windows update

  * original title - whenever I have install windows update install but after pc restart I cannot connect to internet__b'coz when I double band click on the connection, it will not open__due for this I have to restore all the updates__please help *.

  Hello

  1. what operating system do you use?

  2 you get an error message while trying to access the internet?

  3 what updates did you install?

  1. you try to install an update in both clean start state (restart the computer after installing each update) and check the update is causing this issue and send the same return.

  Put your boot system helps determine if third-party applications or startup items are causing the problem.

  Try the steps instep 1 in the article to put your computer in clean boot mode.
  http://support.Microsoft.com/kb/929135

  For Windows XP:http://support.microsoft.com/kb/310353

  Note: To restore your computer to a Normal startup mode, follow these steps:

  a. click on start in the box start the search.

  b. type msconfig and press ENTER.

  If you are prompted for an administrator password or a confirmation, type the password, or provide confirmation.

  c. under the general tab, click Normal Startup - load all device drivers and services and then click OK.

  d. When you are prompted, click on restart.

  Install Windows updates in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/install-Windows-updates

  2 please check the items below to solve the problems of internet connectivity.

  Why can't I connect to the Internet?
  Using the troubleshooter from network in Windows 7
  Use Network Troubleshooter event logs to solve network problems

  In Windows network connection issues

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• Windows cannot connect to the Internet using HTTP, HTTPS or FTP. This is probably caused by the settings of firewall on this computer.

  I have a laptop Toshiba Satellite M105-S3041 with Windows XP Home Edition.  I received the error message listed above indicating that Windows cannot connect Internet using HTTP, HTTPS, or FTP.  When I open the wireless network connection status, I see packets sent and I also see that I get both packets.

  The opening to the top of Internet Explorer, I received the error message listed above.  When I go to the properties of my wireless adapter and examine the properties of the TCP/IP parameters, I see that I have "obtain an IP address automatically" and "Obtain DNS server address automatically" checked.  On the general tab of TCP/IP properties, I clicked on the tab advanced and click on the tab options to display the TCP/IP filtering settings and clicked the properties button.  Here, I see that the ports TCP, UDP and IP PROTOCOL.  I have a check the box 'enable TCP/IP filtering '.

  Please help me because I am still unable to connect to the internet.

  [snip]... On the general tab of TCP/IP properties, I clicked on the tab advanced and click on the tab options to display the TCP/IP filtering settings and clicked the properties button.  Here, I see that the ports TCP, UDP and IP PROTOCOL.  I have a check the box 'enable TCP/IP filtering '.

  In general, you don't want to have a check in the box "enable TCP/IP filtering.  Try to uncheck this box and see if it helps.

  If this does not help, two programs freeware difficulty sometimes of the problems of this kind...  Try to run LSPFix and/or WinSockXPFix.  Alternatively, you can try to reset your IP stack...

  "How to reset the Protocol Internet (TCP/IP)"
    <>http://support.Microsoft.com/kb/299357 >

  HTH,
  JW

• Error: "Windows cannot start the windows firewall/internet connection sharing (ICS) service.

  On my Eee PC under XP Home edition tablet, I get the error "Windows cannot start the windows firewall/internet connection sharing (ICS) service" when I try to access my firewall. I also can't connect to my router Wireless Lan to go on the internet. This may be due to some viruses that have been deleted using Microsoft Security Essentials.But the problem persists. Could recharge SP2 solve this problem or am I condemned to reload the operating system?

  Hi jdmanel,

  NOTE: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://support.Microsoft.com/kb/322756

  Follow the steps in the article.

  You cannot start the Windows Firewall service in Windows XP SP2

  Troubleshooting settings of Windows Firewall in Windows XP Service Pack 2 for advanced users

  For reference:

  How to manually open ports in Internet Connection Firewall in Windows XP