5548, 7048 - PowerConnect backup SNMP configuration

Similar Questions

• Question about KB 2033173 - SNMP configuration

  Hi guys, I have a question about KB 2033173. It is said

  below is an example of the host SNMP Configuration profile:

  Port 161

  Community

  Community 10.0.0.1@0 receiver

  [...]

  Please note that the recipient's address contains a space, not a "/" as input to the command line.

  
  

  I wonder why the "10.0.0.1@0"? I think it should be "10.0.0.1@161" because the port number is 161. Thank you.

  
  

  
  

  Yes, you are correct and also keep in mind that there is a lot of difference with the SNMP agent without traps (use the port UDP/161) and SNMP agent with traps (use port UDP/162).

  

• SNMP Configurations require vCenter?

  I am running vCenter on top a pair of cluster 2 ESXi hosts 4.1.0u3.  I have configured the Protocol SNMP configurations is vCenter to point to our appropriate receiver.

  A few questions come to mind with this, can someone enlighten me please!

  
  

  Although the SNMP configuration is applied in the vCenter settings, they need to be configured on each host ESXi?  If so, how it works?

  On a separate scenario (has nothing to do with the above), I have 2 ESXi hosts running ESXi 4.1.0u3 - but they are not in a cluster and do NOT contain a vCenter Server.

  How can I go about configuring SNMP for each of these individual ESXi hosts?

  Thanks for the help guys prerequisites!

  I remember using vcli for the same. Discover this useful KB

• PowerConnect 2824 - SNMP monitoring

  Hello

  I want to monitor the State of a switch Dell PowerConnect 2824 using SNMP. I have trouble finding the proper MIBS.

  Edit: I managed to access the switch through the web interface and am SNMP receives traps as expected.

  2) whose identifiers are available for monitoring: power, temperature, load, connections, faults, etc.? Where can I find the MIB files? Or documentation explaining the use of more detailed?

  Advice or documentation links are appreciated.

  Thank you.

  The MIB file is included in the download for the firmware.

  www.Dell.com/.../drivers

• Backup of configuration Cisco Codec C40

  Dear all,

  Can I know how to take backup of the configuration of the Cisco Codec C40, please?

  And also help me with the document of the administrator?

  Thanks in advance

  Kind regards

  Syed

  You can simply copy the output of the xConfiguration and paste it into the SSH client.  You may need to change the output a bit to get the correct formatting, however.  For example, the output registered since my SHH client contains a preceding * c which must be removed before that I can stick again in the SSH client:

  *c xConfiguration Video Wallpaper: Waves

  When you perform a software update, codec configuration, including the keys installed option is not affected and will remain in the process. Keys options include Premium (PR), double (DD) display resolution and Multisite (MS). C40 has been end of sales since June 2015, so it is not possible to order anything for this, see eos-eol-notice-c51-733467. Procedure to upgrade the software codec is on pg 28, the same page mentioned in my previous answer. To upgrade codec software, you will need a release key when switching from one major version to another, as TC5 to TC7. You can request a release of the Cisco Licensing Portal key > obtain other Licenses > telepresence free software key, as long as the device has an active support contract. If you do not have an active support contract, you can contact TAC and get the free unlock key by referencing the Security Advisory cisco-sa-20160504-tpxml, which you can get a key to unlocking TC7.

• Backup folder Configuration Cisco first infrastructure 2.0?

  Hi all

  where is the backup devices folder in PI 2.0 configuration, I tried searching with winscp for *.cfg but have not found anything.

  the most funny thing is when I am connected via the WEB (GUI), I can see the configurations of devices (under configuration of archive).

  so anyone know where is the file?

  Thank you

  Dawit

  Hi Dawit,

  https://supportforums.Cisco.com/message/3975460#3975460

  check the thread above, hope this will answer your query...

  Thank you-
  Alya
  [Note the useful post]
  Ratings encourage contributors *.

• How backup VPN configuration between two universities?

  Hello, I am a student of the Greece and I have a graduation project to configure Backup VPN between two universities. Principal of communication made with leased lines. I study a lot, but now that it's time for implementation I have some thoughts:

  -What hardware and software IOS do I need? Cisco 1841 it is ok for A & D routers?

  -Use GRE IPSec transport mode or IPsec Tunnel mode?

  -What will be the failover mechanism for switching traffic lines leased to IP VPN Backup and opposite? A teacher told me something about the Interface Prioritys. I read somewhere that this is done with the such as EIGRP routing protocol. who was right the Professor or the book?  :-D

  -In the same place, they have Firewall and NAT, I need to do any action for this?

  The attached file contains topology I want to implement

  'My' talk site 1

  2 a Central Site

  E communicates with A, but no traffic is to A of E with normal circumstances. Subnet on E access Internet through F, then press D.    VPN will be implemented on the LAN but the specific source E traffic will pass through the Backdoor VPN (I think that the solution to this is ACL on the router). They have no routing protocol in 'my' site A directly connected routers and the default routes.

  How imlement this?

  I think the first thing to do is A to D connectivity

  I will try to do this to tracers package first, but how can ' I imitate the SP network?

  I need help I can get!

  Hi John,.

  In our scenario, given that our main connection is a direct leased line between E and F, so I guess there is no other network between the two routers. In this case we do not need to configure SLA monitoring or any interface a priority. We can simply enter two default routes:

  IP route

  IP route 254

  In this scenario, if the leased line interface goes down, the second default route is used and the traffic should be routed by A router.

  SLA monitoring monitors connection (using the ping tests) by one of the interfaces of the router, and when we are not able to ping from one server (specified in the configuration of the SLA) through the interface, then we change the default track to track traffic through some other interface.

  So, in your scenario, we can monitor the connection between E and F, and when the link goes down, we can change the default route to point a.

  This is useful in the scenario where we have another ISP connection as our primary connection.

  Here is a link on how to configure SLA monitoring on the router:

  http://www.Cisco.com/en/us/docs/iOS/12_4/ip_sla/configuration/guide/hsicmp.html

  After you have configured the SLA followed by using the link above, you can bind it to the default route by using the following command line:

  track road IP / / default main route

  IP route 255 / / default route with a metric of higer that comes into play when the main default route goes down

  In addition, the sample configuration that you give in the doc is almost correct, defined transformation is missing just a hashing algorithm. Here is a link with an example for a tunnel from lan-to-lan between two routers:

  http://www.Cisco.com/en/us/partner/products/HW/routers/ps221/products_configuration_example09186a008073e078.shtml

• SNMP configuration on ASA 5520

  I was wondering if someone could provide me with basic configuration or a link to the basic configuration for the monitoring of SNMP on an ASA 5520.

  Thank you

  Chris

  SNMP-server host within the 192.168.1.185 community XXXXX

  ^ - Configures only host 192.168.1.185 can get snmp data

  Server SNMP community xxxxx

  ^ - open to everyone, if you want to

  location of Server SNMP-individuals

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Server enable SNMP traps syslog

  Server SNMP traps enable ipsec works stop

  Server enable SNMP traps entity config - change insert-fru fru - remove

  Server SNMP enable doors remote access has exceeded the threshold of session

  This should be the biggest part of what you need

• How to take backup of configurations of routers/switches by a script automated

  Hi friends,

  Can someone suggest me a script to do the backup of the devices(routers/switches) network. As the running configuration with only once for all devices.

  Thank you

  Mohammad.

  Two ways you can do this but it must be enabled on each device, if you do not have something like LMS/premium to seize all the configs devices centrally

  Command and tftp configuration of a device on your network of archives

  http://www.Cisco.com/c/en/us/TD/docs/iOS/fundamentals/command/reference/cf_book/cf_a1.html#wp1018716

  or use a job of kroon, the calendar and send it to a storage device

  http://www.Cisco.com/c/en/us/support/docs/iOS-NX-OS-software/IOS-software-releases-122-mainline/46741-backup-config.html#AB

  just a few options it is probably more ways as well

  Edit

  You can use the EEM aswell

• The SNMP Configuration failure

  Hello

  I'm trying to configure SNMP v3 on a host running 5.5u1. When I try and set the authentication and privacy I'm greeted with the following error: / tmp/hash_snmp_34068 child process failed, returned exit code = 1:

  hash of esxcli system snmp - raw-secret-auth-hash password - priv-hash password

  Any ideas what could cause the failure?

  THX.

  Sorted. I never put the privacy of snmp. I put privacy at AES128 that sorted an error (/ tmp/hash_snmp_34068 child process failed, returned exit code = 1) which came later in the configuration.

• SNMP configuration

  Hi all

  We have Esxi 5.1 environment in our Organization, we must activate SNMP on all hosts. I have all the information of the SNMP protocol as, rope, add IP and port.

  But I don't know how to activate the SNMP on the host.

  Need help on setting up SNMP on the host, as I do for the first time

  Thank you all.

  You can check the status of snmp using 'esxcli system snmp get. "

  To activate snmp use the following command:

  "esxcli system snmp set e true.

  Other parameters can be configured with the following options:

  / var/log # esxcli system snmp set - help

  Use: esxcli system snmp set [command options]

  Description:

  together, that this command allows the user to configure the SNMP ESX agent.

  Cmd options:

  -a |-authentication =

  Default authentication protocol. Values: none, MD5, SHA1

  -c. | -communities =.

  Define up to ten communities every step more than 64 characters. The format is: Community1 [, communaute2,...] (This replaces previous)

  settings)

  e |-allow to start or stop the SNMP service. Values: [Yes | No, true | false, 0 | 1]

  E |-engineid = id of motor Set. SNMPv3 must be at least 5 to 32 characters hexadecimal. x 0 is stripped if found and the colon (:))

  y |-hwsrc = where of events material source of IPMI or Indications CIM sensors. An a: directions | sensors

  l |-loglevel = the Agent System syslog logging level: debug | info | WARNING | error

  n |-notraps = use separate comma: esxcli system snmp set [command options]

  Please let me know if it helps.

• Script to join the domain, the role of configuration, add permissions and activate/SNMP configuration

  So I'm writing a script to install our vSphere hosts to work with our monitoring software.  Right now, it's all done by hand and I would like if possible to automate it.  So far, I came up with this.  I get to step 5 and that's where it fails.  I can get it manually run the Get-VIAccount command, but in the script, it fails.

  These are my steps

  1. connect to an existing host and retrieve role properties.

  2. connect to the new host

  3 join the domain.

  4. disconnect the new host and reconnect with the credentials of domain

  5. get the domain account, role of research/create and add permissions to host

  6. enable and configure SNMP

  7 restart MGMT officers.

  #Variables

  $vmhost = "Host03".

  $domaintojoin = "Domaine.org".

  $domainAlias = "domain".

  # $usernametograntpermissions = "service.account".

  $rolename = 'team - account control service '.

  #Connect to host17 to retrieve the role privileges

  to connect-viserver host17

  #Extract of privileges for the role of vcenter Monitoring Service

  $privsforrole = get-viprivilege-role (get-ferrule-name $rolename)

  Server VI #disconnect

  disconnect-viserver *-confirm: $false

  VSphere hosts #Connect above (enter the credentials of the root when prompted)

  SE connect-viserver-Server host03

  #Join field

  Get-vmhostauthentication - VMhost ctcvsphere3 | Game-VMHostAuthentication-domain $domaintojoin - user %-% - JoinDomain-confirm password password: $false

  credentials of the #disconnect root

  disconnect-viserver *-confirm: $false

  #reconnect with the credentials of domain

  SE connect-viserver-Server ctcvsphere3-user username-password password % domain\username

  #Get domain account and add to the host

  $viAccount = get-VIAccount-DOMAIN-User - ID service.account

  # Get the role

  $viRole = get-ferrule-name $roleName

  If (-not $viRole) {}

  throw the "Role of the creation.

  New-ferrule-name $rolename - Server $vmhost

  Together-ferrule-role (Get-ferrule-name $rolename - Server $vmhost) - AddPrivilege (get-VIPrivilege-id $privsforrole - Server $vmhost)

  }

  # Add permissions on VMHost

  New-VIPermission-Director $viAccount-role $viRole - entity $vmHost

  all VIServers #disconnect

  Disconnect-VIServer *-confirm: $false

  }

  #Configure SNMP

  Get-vmhostsnmp | set-vmhostsnmp-enabled: $true

  Get-vmhostsnmp | game-vmhostsnmp - ReadOnlyCommunity 'SNMP.

  #Restart Mgmt officers

  Get-VMHostService - VMHost $vmhost | where {$_.} Key - eq "vpxa"} | Restart-VMHostService - Confirm: $falese - ErrorAction SilentlyContinue

  Here is my error:

  Get-VIAccount: 27/02/2014-16:03:11 VIAccount Get A general system

  rror occurred: access to the directory error

  C:\ps1\vmware\snmp1.ps1:42 char: 28

  + $viAccount = get-VIAccount < < < < - domain - User - ID SERVICE. ACCOUNT

  + CategoryInfo: NotSpecified: (:)) [Get-VIAccount], SystemError)

  + FullyQualifiedErrorId: Client20_VmHostServiceImpl_RetrieveUserGroups_Vi

  Error, VMware.VimAutomation.ViCore.cmdlets.Commands.PermissionManagement.GE

  tVIAccount

  Get-VIAccount: 27/02/2014-16:03:11 Get - VIAccount VIAccount with the id

  "service.account" was not found using the specified filters.

  C:\ps1\vmware\snmp1.ps1:42 char: 28

  + $viAccount = get-VIAccount < < < < - domain - User - ID SERVICE. ACCOUNT

  + CategoryInfo: ObjectNotFound: (:)) [Get-VIAccount], VimExceptio)

  n

  + FullyQualifiedErrorId: Core_OutputHelper_WriteNotFoundError, VMware.VimA

  utomation.ViCore.Cmdlets.Commands.PermissionManagement.GetVIAccount

  New-VIPermission: Impossible to validate the argument on the parameter "principal." The argument

  ent is null or empty. Provide an argument that is not null or empty, and then try

  the command again.

  C:\ps1\vmware\snmp1.ps1:56 tank: 40

  + New-VIPermission-main < < < < $viAccount - $viRole - entity role

  y $vmHost

  + CategoryInfo: InvalidData: (:)) [new VIPermission], ParameterBi)

  ndingValidationException

  + FullyQualifiedErrorId: ParameterArgumentValidationError, VMware.VimAutom

  ation.ViCore.Cmdlets.Commands.PermissionManagement.NewVIPermission

  The term 'catch' is not recognized as a cmdlet, function, script fi

  the, or an executable program. Check the spelling of the name, or if a path has been included

  DED, make sure the path is correct, and then try again.

  C:\ps1\vmware\snmp1.ps1:57 tank: 12

  + captures < < < < {}

  + CategoryInfo: ObjectNotFound: (catch: String) [], CommandNotFou

  ndException

  + FullyQualifiedErrorId: CommandNotFoundException

  Thanks in advance!

  Dimitar did a nice write-up of this phenomenon and a possible solution.

  See ESXi hosts to join a domain and licensing with PowerCLI

• ESXI 5.1 SNMP configuration

  M i tried to configure snmp on a host ESXI5.1 on a DELL PowerEdge R710

  I'm using the command

  Perl vicfg - snmp.pl - Server 65.x.x.x - username XXX - Password XXX 'option '.

  I started with a chcp command error that has been corrected. But now each attempt any option returns the same error that it's trying to define the community string

  Evolution Community list to: rfapoll...
  Use of an uninitialized value chain eq to C:/Program Files (x 86) / VMware/VMware
  vSphere CLI/Perl/lib/VMware/VIMRuntime.pm line 81.
  Use of an uninitialized value in concatenation (.) or string at C:/Program Files (x
  (86) / VMware/VMware vSphere CLI/Perl/lib/VMware/VIMRuntime.pm line 50.
  Undefined subroutine & cannot call the method "ReconfigureSnmpAgent" on an undefined v
  Alou esxcfg - snmp.pl line 297.
  : fault_string called for esxcfg - snmp.pl line 299

  SNMP is imprtant to our monitoring.  Thanks for any help you can offer

  It seems that the orders have changed. See: https://www.vmware.com/support/developer/vcli/vcli51/vsp5_51_vcli_relnotes.html

  New esxcli system snmp namespace replaces vicfg-snmp orders. The following commands have been added.

  • esxcli system snmp get | hash | set | test

• ESX host SNMP configuration

  I'm about to go crazy trying to understand how to configure snmp on an esx host using Orchestrator.  I see the object for it (VcHostSystem.configManager.snmpSystem), but the value is null when I try to use it.  I used the managed object browser and of course, it appears under the "unplugged" position  The api documentation confirms that this is where I'd go for update this configuration but I can't seem to make this work.  All the research that I show people using one of the line of remote control tools to define.  Can someone help a way that they do with orchestrator?  I guess I could create a workflow that calls for the command-line utils, but that seems barbaric.  I also thought that maybe I could manipulate the XML directly on the host computer, but then again, it seems more like the caveman.  If all goes well, Miss me just something obvious in my attempts to do so.

  Here's my test code:

  var myVcHostSnmpConfigSpec = new VcHostSnmpConfigSpec();
  ro var = new Array;
  trap of var = new Array;
  var destination = new VcHostSnmpDestination();
  destination.Community = "SNMP community";
  destination.hostName = '127.0.0.1 ';
  destination.port = 162;
  RO.push ("read-only");
  Trap.push (destination);
  myVcHostSnmpConfigSpec.enabled = true;
  myVcHostSnmpConfigSpec.readOnlyCommunities = ro;
  myVcHostSnmpConfigSpec.trapTargets = trap;
  System.Debug ("snmpSystem:" + esxHost.configManager.snmpSystem);
  System.Debug ("active snmp?" + esxHost.configManager.snmpSystem.configuration.enabled);
  System.Debug ("read only communities:" + esxHost.configManager.snmpSystem.configuration.readOnlyCommunities);
  System.Debug ("trapTargets:" + esxHost.configManager.snmpSystem.configuration.trapTargets);
  System.Debug ("CS:" + myVcHostSnmpConfigSpec);
  System.Debug ("CS.enabled:" + myVcHostSnmpConfigSpec.enabled);
  System.Debug ("CS.readOnlyCommunities:" + myVcHostSnmpConfigSpec.readOnlyCommunities);
  System.Debug ("CS.trapTargets:" + myVcHostSnmpConfigSpec.trapTargets);
  System.Debug ("CS.trapTargets:" + myVcHostSnmpConfigSpec.trapTargets [0] .community);
  System.Debug ("CS.trapTargets:" + myVcHostSnmpConfigSpec.trapTargets [0] .hostName);
  System.Debug ("CS.trapTargets:" + myVcHostSnmpConfigSpec.trapTargets [0] .port);
  esxHost.configManager.snmpSystem.reconfigureSnmpAgent (myVcHostSnmpConfigSpec);

  This seems to be one or the other of these unfortunate ESXi features that can be managed through a vCenter. So, for each host that you want to manage, you must import the SSL certificate and add the host to the vCO so that such changes. Based on my test script manually to add the SSL certificate and the facilitator to my server of vCO I could set the SNMP parameters as you coded above.

• ESXi 4.1.2 SNMP configuration

  Hello guys I need to configure more than 3 targets in my configuration of SNMP. How do I do that?

  I have the command:

  vicfg - snmp.pl - host.example.com - username root - password password you target.example.com@162/public

  I need to run this command 3 times or I use commas to insert all the targets?

  Anyone know?

  Thank you.

  Just tested the string.

  vicfg - snmp.pl - Server - username root t 1.1.1.1@162/public,2.2.2.2@162/public

  / etc # cat /etc/vmware/snmp.xml
  
   
     
      fake
      1.1.1.1@162 public public;2.2.2.2@162
   
  / etc #.

  -KjB