6120 link down on mgmt0 triggers not UCS Manager failover cluster - is?

Similar Questions

• My drop down bookmark does not offer 'manage bookmarks '. Support find Ican, is how to change the bookmarks. How can I find the link manage if this isn't in the menu drop-down?

  Question
  My drop down bookmark does not offer 'manage bookmarks '. All the support I can find that this is how to change the bookmarks. How can I find the link manage if this isn't in the drop-down list?

  In Firefox 4, "Organize bookmarks" was changed to "Show all bookmarks" to open the library window.

• Cisco 6248 FI to Brocade 6510 SAN switch shows Link Down

  Hi all

  His new installation of Cisco UCS with Brocade SAN switch 6510.

  I followed the Cisco UCS to Brocade connectivity Guide.

  Even if the switch side so FI link is not coming. No lights are glowing.

  When I checked the switchshow @Brocade 6510, ports are No_Light status display. Where in other ports, it indicates the number of my storage device WWN.

  At the END, when I click on ports CF, its projection on all State - link down.

  Any who are facing this problem. ?

  Am I missing some configuration steps?

  Kind regards

  Praveen

  This should be a trivial or a very complex problem. I'd rather commonplace.

  Brocade is a CF 16 G switch; up to 8 G negotiation seems to work (storage subsystem).

  Maybe you could try to set the speed on the Brocade 8G port fix!

  Or something with the cables is wrong? Send / receive Crusaders?

  Are shortwave of the MMF SFP? cables connection as well?

  Connect cable from port for example. 31-33, 32 to 34 and see if it works?

• for some reason when I log in it will say blocking down, but it dose not after an hour, it is now more than 30 days

  for some reason any when I connect it says blocking down but it dose not after an hour I would push the bar on or pull off the Gack DC it's been driving me crazy

  Hello

  ·         What operating system do you use?

   

  Method 1:

  I suggest you perform the clean boot and check if it helps.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135/en-us

  Note: Don't forget to start your machine in normal mode by following step 7 of the link.

   

   

  Method 2:

   

  If you are facing this problem in Windows XP, see this link:

  Advanced Troubleshooting for shutdown problems in Windows XP

  http://support.Microsoft.com/kb/308029

  Method 3:

  Refer to the Kb article and check.

  You can't do a computer that runs Windows 7 stops or sleep

  http://support.Microsoft.com/kb/977307

  Try to run the troubleshooter of performance and check if it helps.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-performance-Troubleshooter

  Method 4:

  Also check the event viewer

  Event Viewer is a tool that displays detailed information about important events on your computer.

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

• Fault clearing UCS Manager on linking rising unused C-series adapter

  I have a number of C240M3 servers in an infrastructure of the UCS.  They have all two adapters VIC 1225 and when they were connected to the start, technicians accidentally connected the second card on some of them to the aircraft.  For now at least, we want to only first used adapters (two ports - one for each FEX).  However, as map 2 was connected at a given time, UCS Manager will not stop giving these flaws:

  F0206 - adapter 5/2 is inaccessible

  F0209 - link interface rising adapter 5/2/1 the link status: unavailable

  There is not a way to erase the mistakes without this second reconnecting.  Re-recognition of the server has not helped and I'm not sure I want to try their decommissioning and then get them to appear in the UCS.

  Does anyone know how to clear these faults manually?

  Open a TAC case and get TAC watch mistakes, then we can try to delete them, if they are real error messages.

  -Kenny

• Re: Portege M700 - download link for the BIOS does not

  Tried to download the file to update the BIOS for Portege M700 on the Toshiba site with no luck. The file is 1: 60 - WIN. No luck. Is the link down or something? Could someone please try?

  Hello!

  I agree with zuja.
  I tried to download the BIOS for Portege M700 and now it works.

  Now you can update the BIOS. :)

  Good bye

• Cannot open links in Safari, Messages, messages, Notes and other applications.

  Problem on the iPhone 6 and iPad pro since version 9.3 I can't open links in Safari, Messages, messages, Notes and other applications. Rather than visit the target website, the application crashes, freezes or crashes.

  How to fix bug of broken links ios 9.3 safari/mail:

  (1) find and uninstall the application of booking.com, if you

  (2) wait at least 1 hour, the bug disappeared. Perhaps you need to reboot once

  to reproduce the bug again: install the app booking.com

• No solution workaround for links to KB which do not work?

  Hello

  Is there no workaround for links to the knowledge base not work not?

  It has been a while since I tried to use the support site. It is changed so that I'm completely lost. I can't find the Knowledge Base articles, and when I find a link that should take me to a KB article I get a 404 error.

  Link to example

  https://support.Apple.com/en-us/HT203202

  Thank you.

  How you try to use the support site? What is your workflow?

• Search bar on the Macbook Air doesn't work, will allow me to load the pages of Favorites and links to these pages, but not let me google from the bar or manually enter Web sites, however, it works perfectly on the guest user

  Search bar on the Macbook Air doesn't work, will allow me to load the pages of Favorites and links to these pages, but not let me google from the bar or manually enter Web sites, however, it works perfectly fine on the guest user. Have you tried restarting and it still does not work.

  The problem should be solved now.

  Otherwise:

  OS X

  iOS

  Workaround for problems with the Safari address bar

  http://osxdaily.com/2016/01/05/fix-Safari-freezing-address-bar-use/

• I'm looking for a link to XP SP1 does not require a network connection to install

  I'm looking for a link to XP SP1 does not require a network connection to install

  Were you recently doing a Clean Install? I ask because you are implying in your installation of Windows XP is in 'gold' or SP0 (i.e., pre - SP1) level. Well sure, automatic updates will not work!
  You can use this path to level – says in passing:
  Gold XP to XP SP2 to XP SP3.
  Note that installing SP1a is TOTALLY USELESS!
  Here are the detailed instructions:

  1. download the installation of SP2, SP3 and IE8 files. I prefer to keep these on a USB key, but this is optional. Here are the links to all the installation of three files:

  http://www.Microsoft.com/download/en/details.aspx?ID=28 (for SP2)

  http://www.Microsoft.com/download/en/details.aspx?ID=24 (for SP3)

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=43 (for IE8)

  And if you wish, download the Setup file of a good anti-virus program. I recommend Avira free Antivirus:

  http://www.Avira.com/en/Avira-free-antivirus

  2. disconnect Internet.

  3. temporarily disable the automatic updates.

  4. install SP2. Restart twice.

  5 install the SP3. Restart twice.

  6 switch to IE8. Restart twice.

  7 install an Antivirus software.

  (What happens very often is that someone has their software antivirus running as they try to install SP3, which often translates into chaos! "This is why it must be done after installing SP3 and IE).

  8 make sure that firewall Windows is activated (it should be).

  (Now you can physically reconnect to the Internet.)

  9 visit Windows Update to download and install only the critical security updates.

  10 re - enable automatic updates.

  After the back if you need guidance.

• I am trying to install a D-Link router, but it will not designate the correct IP address.

  Im trying to install a d-link router and it will not get the correct ip address. I then tested on my roommates with a newer version of windows laptop and the router has worked. d-link technology says I may new new setting lan drivers installed for this problem. help someone?

  original title: router problems

  Make sure that this adapter you set obtain IP and DNS addresses automatically.  Go to your network connections and right click on your internet connection and select 'Properties', then click on (highlighted) Protocol Internet (TCP/IP) and then click on the properties button and make sure that the IP address and DNS are both set to obtain automatically addresses.

  Go to the Services management console (type services.msc in the box run from the start menu) and make sure that the DHCP Client service is set to automatic startup.  Restart the computer and see if things improve.

  John

• Link down stackable modules

  Hello, I'm trying to understand why I am unable to get my status as a link on my switches for ports 1/xg1 & 2/xg2. I have swapped the cables but still the same LINK down. TX1-CORE-SW-STK01 #show stack-port configured running battery battery link link Unit Interface Mode status Mode speed (Gbps)---1 xg1 battery battery Link Down 12 1 xg2 battery battery Link Up 12 1 xg3 Ethernet Ethernet Link Down unknown 1 xg4 Ethernet Ethernet Link Down unknown 2 xg1 battery battery Link Up 12 2 xg2 battery battery Link Down 12 2 xg3 Ethernet Ethernet Link Down unknown 2 xg4 Ethernet Ethernet Link Down unknown - I also tried to re add the battery but still no go... TX1-CORE-SW-STK01 #configurer TX1-CORE-SW-STK01 (config) #stack TX1-CORE-SW-STK01(config-stack) #stack - port 1/xg1 battery TX1-CORE-SW-STK01(config-stack) #stack - port 2/xg2 battery TX1-CORE-SW-STK01(config-stack) # TX1-CORE-SW-STK01 #copy running-config startup-config, this operation may take several minutes. Management interfaces will be unavailable during this period. Are you sure you want to save? (y/n) y stored Configuration! TX1-CORE-SW-STK01 #show stack-port 1 xg1 battery battery Link Down 12 1 xg2 battery battery Link Up 12 1 xg3 Ethernet Ethernet Link Down unknown 1 xg4 Ethernet Ethernet Link Down unknown 2 xg1 battery battery Link Up 12 2 xg2 battery battery Link Down 12 2 xg3 Ethernet Ethernet Link Down unknown 2 xg4 Ethernet Ethernet Link Down unknown

  Hello Josh,.

  It turned out that the stacking in the switch module was bad.  We ordered another one traded and I got the top / upward

  TX1-CORE-SW-STK01-stack-port #show

  Set up running

  Battery battery link link

  Speed unit Interface Mode Mode status (Gb/s)

  ---- ---------------- ---------- ---------- ------------ ------------

  1 xg1 battery battery Link Up 12

  1 xg2 battery battery Link Up 12

  1 Ethernet Ethernet Link Down unknown xg3

  1 Ethernet Ethernet Link Down unknown xg4

  xg1 2 battery battery Link Up 12

  2 xg2 battery battery Link Up 12

  xg3 2 Ethernet Ethernet Link Down unknown

  2 Ethernet Ethernet Link Down unknown xg4

  TX1-CORE-SW-STK01 #.

  Thanks for your help.

• Cisco UCS Manager does not discover C240 Server

  Hello, Cisco community!

  Currenlty UCS manager shows two interconnections of fabric and two extensions of fabric, but for some reason, my server isn't appear

  Birds seen are:

  I have my C240 connected with two 10GbE twinax cables, each going to a fabric Extender. (Total FEX 2)

  I have two 10GbE twinax cables connected each interconnections FEX fiber modulus in each tissue. (Total of 2 FI)

  The fabric interconnect ports L1 and L2 are connected to their corresponding ports. If their connected to each other.

  I run 'show cluster extended State' on the primary FI and this is what I get:

  FI - A # show cluster extended State

  The ID of the cluster: 0xebaad0e28ded11e3-0x86d4002a6a153d84

  Start time: Thu Feb 5 16:07:44 2014

  Last election period: Thu Feb 5 16:23:26 2014

  A: UPWARD ELEMENTARY SCHOOL

  B: UP, SUBORDINATE

  A: Member State UP, lead, State State PRIMARY, mgmt services: UP

  B: Member State UP, lead SUBORDINATES, mgmt services state: to the TOP

  State of PRIMARY_OK heartbeat

  INTERNAL NETWORK INTERFACES:

  eth1, up to

  eth2, up to

  HA IS NOT READY

  Any device attached to this fabric of interconnection

  After you set up server-side on each FI ports, the server still does not appear

  Any ideas are highly appreciated!

  -Alex

  Hi Miguel

  It seems to me, you're running a rather old version of UCS.

  In my screenshot you see the pool ext - mgt KVM on the LAN tab

  In an older version (I think< 2.1),="" this="" was="" under="" the="" admin="" tab.="" please="" have="" a="">

• Windows 7 search returns results from Outlook 2013, but links to the message will not open the e-mail message.

  Windows 7 search returns results from Outlook 2013, but links to the message will not open the e-mail message.  Other results such as Excel or Word work.  When you click on the result of the e-mail, the small window at the bottom of the page displays only the title of the email but no information such as the type of file or the date that you would see with other types of file returned.

  Hi Houston,

  Please refer to the article:

  Open the troubleshooter for search and indexing

  http://Windows.Microsoft.com/en-in/Windows7/open-the-search-and-indexing-Troubleshooter

   
  For outlook, try built-in archiving option to facilitate the research for you. Please see the description and functionality of AutoArchive in Outlook from the link below.
  http://support.Microsoft.com/kb/830119
   
  Let us know the result. If the problem is still not resolved, we will be happy to help you further.

• Drop-down menu SENDTO does not contain the same list as in the SENDTO folder in the User\Appdata\microsoft\windows\sendto folder.

  Prior to Win7 and Vista (seems to have the same problem), make a right click on a file would produce a drop down menu containing SENDTO containing various options like send this Word file, or write or Adobe or desktop (make a shortcut).  Other options of destination could be added by finding and opening the SENDTO folder and dragging shortcuts in there.  These added destinations would appear then in the menu drop down click the right button.  The feature doesn't seem to work in Win7.  The SENDTO drop contains the locations that are not in the SENDTO folder.  I've renamed the SENDTO folder to see what would happen.  Always in the same places appear in the menu dropdown.  It seems that Win7 has a situation he's going to other than the SENDTO folder.  Interestingly, I can add some program shortcuts in the SENDTO folder and they will appear in the drop-down list, others do not like the trash.  There are items in the drop-down menu are not in the SENDTO folder.  Help Help

  Click on the round of Windows (start), type shell: sendto and hit enter, add or remove shortcuts. Is it now behave properly?

  I forgot to post the location of SendTo folder, it's C:\Users\UserName\AppData\Roaming\Microsoft\Windows\SendTo