6224 PC kills my network. Help? :)

Similar Questions

• OK, Adobe, why am I constantly being logged onto my CC account? I can't use the software when it maintains the bombing. The problemhas who spends all day and he killed my workfow - HELP

  OK, Adobe, why am I constantly being logged onto my CC account? I can't use the software when it maintains the bombing. The problemhas who spends all day and he killed my workfow - HELP

  Wish I had read this post before posting. Or ran the spellchecker...

  Anyway, people treated at Adobe callcentre solved the problem. Make sure you connect to the CC of the desktop application. So, good job Adobe...

• Weird computer on my network Help!

  There was a weird computer on my network. I tried to change the password and unplug the TimeCapsule airport but, it didn't work. Also, my other computer network services NetBIOS name says under WINS and the mysterious appeared. Computer is a PC but also to the first part of the name with numbers after it. I found the computer in the Finder under shared. No download. Help would be gladly appreciated.

  When I stopped the other computer, it disappears.

• MacBook can not access 1300 HP connected to my local network, help?

  I have a HP LaserJet 1300 connected via a USB hub to a Macintosh G5 tower which is connected by Ethernet to my Telus Optik V1000H Actiontec modem/router. I read (I think on this forum) that some people have kept the modem Gateway 2 son they used before the upgrade of their service internet of Telus Optik and plugged into the router/modem Actiontec V1000H because he has better wireless capabilities. I did too, but now I don't know what modem/router my MacBook can access my network through now (if this is important).

  My new MacBook Pro running OS 10.8.2 accessing my wireless network but cannot access the HP LaserJet 1300. I downloaded and installed the v.2.11 driver of HP on the new MacBook, but when I try to set up the HP LaserJet 1300, I get the error message "Unable to download the software from the server at this time." The MacBook doesn't seem to know that I have already installed the printer driver v.2.11 on it.

  I tried to provide much information as possible here, but the line the bottom is I realized that my new MacBook Pro would be able to print to my HP LaserJet 1300 while the printer is connected to my network... but it can't. Can someone help me? I can't really afford a new printer.

  BTW - after reading some of the messages, I realize I can't have fax capability via my network, but is not serious. I've never used fax anyway.

  I'd appreciate it if someone could help me with some advice or point me to another conversation that could help me. Thank you!

  Hi, I am answering my own question so I can mark it as resolved. I continued to read and try different things, and finally (kind of by chance) I solved my problem. I'm not entirely sure how I did it, but I'll try to explain in case someone else is having similar problems.

  I downloaded the driver for printer HP 1300 (v.2.11) manually at least twice. I got it on the MacBook Pro, but the computer doesn't seem to be able to access it when I had not the 1300 HP directly connected via USB. It was confusing to me, especially when all the literature said to do a software update, if I was in trouble by doing the work of the printer.

  When I went to my printer preferences and tried to set up the HP 1300 with the printer not connected not directly to the MacBook Pro, it came as a printer, but I got a message saying that I couldn't download the software needed at this time there. I left this printer icon on my list of printers. (I knew that I already had the software but couldn't get the printer preferences to realize it is there).

  Then, I connected the HP 1300 directly on the MacBook via USB and the process repeated. This time a HP LaserJet 1300 @ my network was created in my list of printer and print driver was on the MacBook Pro. I chose the HP LaserJet 1300 @ my network version as my default printer. I have connected the printer to my network and was able to print wireless from the MacBook.

  I'll just let the other HP LaserJet 1300 icon on my list of printers in the case removing a problem. I don't know if I need it or not.

  Sorry if my explanation is poor. It would be a miracle if it helped anyone. I'm not very good in this stuff. I got lucky!

• Trojan:DOS / Alureon.E is killing me! Help please!

  Hello, here is my info:

  HP Pavilion dv6985se

  Windows Vista 64

  TrojanOS\Alureon.E is located in MSE and it can not be cleaned

  No changes have been made until the virus/Trojan horse appeared.

  I've dealt with this for almost two weeks and can't seem to get it gone - because the computer is not used for internet access and contains no data, I decided to make a recovery of the system to a State factory Original using the included utility.  After doing this and install the necessary updates, MSE still find the Trojan horse and cannot clean it.  Any suggestions?  I also tried to figure out how to reformat the whole thing, but the computer came with a disk of OS.  Any help would be greatly appreciated!

  Hello

  I would say certainly two other applications, in particular the MMFA with the C Partition and the Partition selected for scanning running recovery.

  EDIT:  You can also try This Application

  If you decide to clean the disk, first order a replacement set of recovery discs using the link below.

  http://support.HP.com/us-en/document/c00810334

  If you have a problem with this link, order them directly from HP.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  You can then wipe the disc HARD integer as follows.

  Using another PC, download and install Killdisk on the link below - (this application will write zeros to the entire disk).

  http://Software.LSoft.net/KillDiskSuiteFree-Setup.exe

  Download and install ImgBurn on the link below.

  http://download.CNET.com/ImgBurn/3000-2646_4-10847481.html

  Access the application of disc kill you have installed in all programs, open the main folder, then select Bootable Disk creators, then the BACK Bootable CD Creator that will burn the ISO on a blank CD bootable.

  During the following process do not worry about all warnings as your recovery DVDs will reformat the HARD drive.

  Insert this CD into your PC which is unable to load the operating system properly. Close Notepad, and then start again to boot from the CD of Killdisk and follow the instructions on the screen to kill disk.

  A brief description of the process here is Killdisk.

  Use it to wipe the entire hard drive, Select (80 h) and press f10 (you will also need to type a confirmation and press enter) - ( This will make sure to include all of the partitions , and then start the process - this may take a few hours!).

  When the process is complete, remove the CD of Killdisk, insert your first HP recovery disc and start the installation.

  Kind regards

  DP - K

• Cannot access the NSLU2 on network - HELP!

  Hello, recently hooked the NSLU2 again after a few years of storage. It fine to the connected router (WRT54GS running tomato 1.25), but for the life of me I can't get to be recognized by the network.  192.168.1.77 ping fails, I have reset the default router without success.

  The Ethernet on the NSLU2 light is on and sometimes flashes.  The light of the port on the router is on. It just will not be displayed in the list of devices in the tomato.

  Running Windows 7 Pro 64 bit.

  Any help would be GREATLY appreciated.  Thank you!

  -Paul

  Hi, use a port scanner to find out that the HTTP port on the slug has been yet defined a former high port number, could access and reset once I got it. I thought that the hardware reset would put this back to 80!

  Thanks for your help

• Network help

  I have a HP printer all in one deSKJET 3050. I recently changed my network name and a password to Sky my wi - fi. now, I can't get my computer to print. Help, please!

  10 iOS?  Does not exist.  On your Mac, go to the Apple menu > about this Mac.

  Then, download and install the latest software for your printer from the "Support & drivers" link at the top of this page.

• Drop ' n Go subnet to breast pre-existing network - Help with routing please

  Hi all

  I consider myself the best entry level when it comes to the Cisco ASA 5505, and I appreciate help or direction that someone would be able to provide regarding this question, I'll have. I'm sure there is something out there for this, but I was still not able to understand this with what I found.

  We currently have our installation of infrastructure like this: modem(69.14.72.6/255.255.255.248)-> ASA (192.168.1.1)-> Switch-> hosts and Servers(192.168.0.X\24).

  What I'm trying to do is to drop in a small router somewhere within this network with its own subnet and be able to communicate back him 192.168.0.X network, so it will look something like this: modem-> ASA-> Switch-> hosts and Servers(192.168.0.X\24) & hosts and Servers(192.168.1.X\24).

  I will allow this traffic if all goes well, then that only have 2 interfaces configured on the SAA (0/0 and 0/1-0/5 inside) outside and without changing the configuration of the switch. A few key phrases that come to mind from my research so far are "Hair pin" and "permit same-security-traffic intra-interface". Also, I am aware of the port-forwarding and as I understand it would not as convenient to configure a rule for each device connected to the 192.168.1.X\24 network.

  I hope someone can help me with this question, I've been at this for 3 weeks now.

  Thanks again to all!

  EDIT: Here is a diagram to help explain what I'm trying to do. The area in red is what I'm trying to add to the others that I already have.

  

  Hi James,

  For the route between the 2 networks, that you will need to either use a layer 3 switch or a "router on a stick".

  Installation of a layer 3 switch would interrupt less to your existing network.

  You are then ASA "inside" interface--> Layer 3 Distribution Switch--> 2 or more switches to access

• Upgrade of the 3 HP VMware ESXi 5.1 update kills Emulex network and cannot be cancelled?

  People,

  I have a serious issue here after the upgrade of the HP Blade 465 BL c G7 with adapter Emulex NC551i double Port FlexFabric 10 Gb..

  The problem: after the successful online update of ESXi 5.1 Update 2 Patch 5 (2000251) in ESXi 5.1 update 3 (2323236) the ESXi server cannot be crazy, or it can ping to the outside network, so she doesn't have to reconnect to the VCenter server.

  Software/Firmware version:

  The version before the upgrade of the server are:

  ~ # ethtool-i vmnic0

  pilot: be2net

  version: 10.2.293.0

  firmware version: 4.9.416.2

  bus-info: 0000:04:00.0

  ~ #

  Since the version above does not work, I managed to download VMW-ESX-5.1.0-be2net-10.2.477.20-offline_bundle-2541837.zip for upgrade the driver VMNic in: 10.2.477.20 but still after the update and restart the network is not able-ping.

  ROLLBACK:

  I also tried to restore to previous work ESXi Server version 2000251 to the help of SHIFT-R but the ESXi server still restart as 2323236 with a network that still worked.

  
  

  Any other suggestions would be greatly appreciated without having to reconfigure the settings of ESXi and the configuration of the switch distributed from scratch.
  

  According to the recipe of HP/VMware here: http://vibsdepot.hp.com/hpq/recipes/HP-VMware-Recipe.pdf

  There is a note about the NC551i:

  

  / Rubeck

• Virtual network on top of problem physical network, help/ideas welcome!

  Hi all

  After abit of expert advice...

  I am currently considering my last year at University project and vmware will be my main platform, I'll create an ethical hacking virtual network for educational purposes. I'm abit undecided about how to go about networking, ideally, I would like to run virtual machines on multiple physical machines and have a virtual DHCP only giving the addresses of virtual machines, so I could keep it on a different subnet, but I guess it's impossible? I couldn't really have static addresses as each machine turned on would be in conflict with each other. The main problem with my task is to head a virtual network on multiple computers that I would have a class of students to each use of a computer of their own. I don't want to go down the road of them have therefore a virtual network on a host that he uses a lot of computer resources and I wish I could change the server they are "experimenting".

  Any help would be greatly appreciated on this, she keeps just racking my brain!

  Thank you

  Hi macetrix,

  Maybe DHCP reservations can make a difference for you?

  As you filter addresses MAC here, you can easily add them when you created a new machine. The MAC address must be displayed in the VirtualCenter Client.

  And another idea is to know if you can use signs with asterisk in the field of the MAC address of your DHCP reservations. As VMware uses the same MAC address format, you can enter this address MAC 'Beach' and only give VMware machines a DHCP lease.

  Hope this helps the brain less crack

  René

  ---

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!

  ---

• Networking help

  Guy.

  I need little help of networking, we have a physical switch and VM heap are attached to it and physical switch isn't a failvoer configuration, so whenever we lose our physical switch all the vm offline, what I can do to level comments to avoid this problem? I think to add additional NIC on a guest and then perform balancing I guess? any ideas would be appreciated...

  Goodness, I thought I was going crazy, glad to see we're all on the same page now... Here is a shot of a network configuration, you can see that 2 bears are assigned to the DMZ portgroup.  vmnic4 and vmnic5 are both connected on different physical switches, so any virtual machine that is part of this portgroup has access to these cards.  ESX decides what Teddy the virtual machine uses so no need to configure anything at the OS level, it is completely transparent.  If a bear down ESX automatically sends the data on it.

  Its much easier that your idea was

  • Kyle

  

• wireless network help

  OK, not really good with this stuff netowork. So someone tell me if this is even possible with the material that I have or what I might need to get to make it work. Would be greatly appreciated. My internet is Comcast. The bridge, he goes to 4 computers with all the ports on the back of it. These 4 computers have access to the internet from it and the local network that is put in place in the office. They can all see each other and works very well. One of the computers that is at the back of the Office I want to set up a wireless access point. I have an old BEFW11S4 wireless router which I thought I could use for this somehow. What I tried was running the cable that runs into the computer and run it in the Linksys router. Then from that connect a cable of that back into the computer. What then, is the computer can access the internet, but no longer sees any of the computers on the LAN. And wireless (phones) can access internet from the router wireless very well as well. What I want is for phones being able to have wifi access, no need for them to see the LAN. But I want the PC to be able to see the office LAN and internet. Don't know what I can do to get there.

  It's quite possible. Set your network using the LAN - LAN configuration. This way all your computers will still each other, internet access and phone will still be able to use wifi. Here's how you configure. Follow this LINK.

• I have a new laptop with Windows 7 and a desktop Dell with Windows Vista and cannot get them to network, help?

  There are residential groups, the other a network - apples and oranges?  I just want the laptop to the beanextension of the desktop - work on word documents, a Note etc. Sync Center does not see the other. John

  Hi JED101,

  Check and make sure that all settings are correct on both computers.

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

  The problems of finding computers on a home network

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-computers-on-a-home-network

• I saw a print of Beijing and sweep on my network help!

  Hi Experts,

  I keep getting this result on my sys on the SAA paper, as much as I hate to say this, this is the Chinese IPs, they have been flooding my network today!

  % 4 ASA-106023: Deny udp src outside:42.96.255.142/53 dst inside:192.168.200.196/60778 by access-group "outside_access_in" [0x0, 0x0]

  % 4 ASA-106023: Deny udp src outside:223.5.2.141/53 dst inside:192.168.200.196/60778 by access-group "outside_access_in" [0x0, 0x0]

  % 4 ASA-106023: Deny udp src outside:42.96.255.92/53 dst inside:192.168.200.196/60778 by access-group "outside_access_in" [0x0, 0x0]

  Fleeing would take care of these attacks on my network or what other technology on my asa can I use to mitigate this?

  I have a sincere opinion.

  Teddy

  No problem.  Thanks for the note.

• Smartphones blackBerry 4.5 update killed my phone - HELP

  Hi all.

  I'm new to Blackberry and have the Curve 8310 on VODAFONE UK. Everything worked fine until I upgraded and now all I get is error 507.

  Can't do anything with it.

  Everything seemed to go well on the upgrade - he asked me a password for my PIN.  Well I had no idea so just a compound.  He continued for a while, then came up with a critical error.  Try again.  So I tried again and still the same ERROR 507.

  Can someone please help as I don't have a phone now.

  Thank you

  I have now tried this 10 times without success.  I downloaded the software upgrade of Vodafone UK to make sure it was OK.  But still nothing.  I am disabled and need my phone.

  Thank you

  Bigyun,

  Did you get your phone work? My apologies for the delay in responding to you.