6510

Similar Questions

• Photosmart 6510: blurry photos, photosmart 6510

  My 6510 began printing blurry photos. I ran a diagnostic report printer and all looks good here. I ran the jobs to clean and align the print heads as well.

  I can print a test page printed, color of boarding cards, etc. very well, but the pictures are blurred.

  I use real ink HP and HP advanced photo paper. My fine ink appear.

  Any ideas?

  Thanks for any help.

  Hello
  
  Please click HEREto access the procedure which should solve the problem.

• HP photosmart 6510: error on hp photosmart 6510 showing-95 when using scan to email

  My photosmart hp 6510 displays error - 95 when using scan to email. Help!

  Hello @twinec, greetings!

  Thank you for joining the Forums of HP Support! I came across the question you posted, and I want to help you with the best of my knowledge.

  You can try a manual DNS address assignment to fix most of the analysis of the questions by e-mail. Try the steps mentioned below and check:

  • Get the IP address of the printer, you can touch the 'Wireless' icon on the Control Panel printer to get the IP address.
  • Type the IP address in your web browser to get the EWS page on your computer printer.
  • Go to the 'Network' tab - click on "wireless (802.11), and then click «network address (IPv4)»»
  • Click on the radio button that says 'Manual of the DNS server' and under manual type favorite 8.8.8.8 and manual replacement enter 8.8.4.4 (it is Google's DNS server address)
  • Save the settings. Restart your modem, router and printer.

  Let me know how it goes! Good luck

  See you soon

  Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!

• Printer won't turn on and have error msg 83 00020 Photosmart 6510

  Photosmart HP 6510: Start button / stop does not illuminate, and the window of the printer has an 83 00020 error code. There is a green light uder blinking camera icon near the card readers. Under XP/sp3. Printer is 4 years old.

  Try to remove the cartridges and reset the power to the printer. If the printer has been restarted on the same error code, then it is possible that one of the parties in the printer did not. If the printer asked for cartridges to install then one of the cartridges is a failure or the printhead system itself is a failure.

• Printing double-sided with a 6510 Photosmart problem

  I have a Photosmart 6510 new and it is supposed to come with automatic duplex printing.

  I tried two-sided printing and followed the advice of many previous thread, but it did not work.

  I use a version of Mac OS X 10.5.8 and Microsoft Word 2008.

  When I go in the menu in the window print and go to "duplex printing", the ability to print on both sides is grayed out, and he said that paper size and type settings don't support duplex printing. What paper should I choose and where can I do this?

  Any help would be great.

  Thank you

  I had the same problem (same MacOS and all) and just got off the phone with tech support, and together, we found a solution.

  In the print window that opens after you select file > print, select paper handling. Click in the checkbox to select "scale to fit paper size. Allows you to select the Destination format. Select from the drop-down LETTER, then we letter two sides of margins. Now, when you go to double printing, you can click on the checkbox to select print front and back. But before you click on 'Print', save it as a "Preset" so that it is much faster to do the next time!

• Maintenance of printhead HP Photosmart 6510/replacement?

  I have a HP Photosmart Plus B209a-m CD035a of model that comes with having its printhead failure (CN643A).  Although I work for HP (Enterprise Services), it is too expensive to replace so I bought a Photsmart 6510 AIO.  The B209a-m, I liked how I could remove the print head Assembly and to clean up the grime of the ink of ramps, etc..  It seems that on my new 6510, the print head Assembly can be without mowing of the cart - but once that loose, there is no authorization to remove the print head for cleaning.

  This can be accomplished?  I have to remove a screw or am I missing something?  As this is a new printer, I was trying to assess if this is a negative in my choice, if it cannot be removed for the maintenance cleaning.

  The only thing I have to add is:

  I managed to remove the print head and used a few head cleaning Epson I've had, in order to eliminate the heads black and color. I guess that distilled water would also work. After cleaning the black works well again.

  Remove the cover as described previously by others.

  After you have removed the cover, remove the print head ASSEMBLY:

  1 carefully remove the film (large 5/16") close looking for band that crosses the print head Assembly by; releasing

  the tension on the left side by moving it to the print head, on the right end drag strip out of the corner

  crochet.   Note the marks and which is the top and left and right side for correct orientation at the meeting.

  2. Remove money (2) springs to the rear of the door-printhead

  3. slide and tilt forward support

  4. carefully remove the ribbons of the support cables (just pull on)

  5 have your way of the print head!

  6. then, I shed cleaner down the screens from the top, then slung to force the vacuum through the head on the

  background. I did several times.

  7 Sling on dry excess fluid, pat with a paper towel

  8 reinstall the cables in water, then put back in the printer, the springs and then re-install the thin layer as the Strip through

  guides on the support (do not forget to install in the same way, it has been deleted in the measure of the top and bottom and that end)

  on the right) and then the lid as described above.

  A note: I got a Kodak printer and went through the same thing with her whenever he had sat for several days without use. Cost me a fortune in ink running the cleaning. Looks like HP's more Kodak. My HP printers with ink cartridges that have the printhead on them are no problem. If they do not print right, just throw away them and with the new cartridge, you also have a new print head. It looks like if I continue to have this problem with this 65510 will travel the path of the Kodak, in the trash! Had the same problem with the Epsons so I guess all that's left are brother and Canon!

  Hope this helps some of you.

  FLASH: 25/03/14 arrested black print again! After extracting new hands in the dirty, I found the real problem that everyone is probably cause trouble. There are pipes on the printhead carrier going to the vacuum pump and him on the side of the printer in a tray in felt. Black hose of my print head was completeyl plugged with dried ink. I could rinse with distilled water and a syringe. This work is not for the faint of heart, but if you tear systematically in such things and that the printer is out of warranty you have to lose! I could guide you how to do it if you're interested, but a bit long for here. Write me if you want information ([under the direction of privacy]). I tell myself that these pipes do not allow to draw the head during the cleaning process, the ink of the pump so it dries just in the head. Good luck.

• Photosmart HP 6510 - can't find the USB port to connect to the computer. It is right in front of my face?

  Photosmart IHP 6510 - can't find the USB port to connect to the computer. It is right in front of my face? I can't find a diagram online. do not have wireless capability. With the help of MacPro with Snowleopard.Thanks.

  Hello

  The usb port is not #22. as seen in the picture. It's in the back of the printer on the side right hiand.

  

  Best regards

  ERICO

• Compaq 6510 b: bootmgr is missing and I don't have a CD/USB

  Hello

  My HP Compaq 6510 b has been infected by the virus of defense crypto. I searched like crazy and could not find any solution and decided to sacrifice my photos and videos. But turned out even restore the laptop is not easily possible. AFAIK, the laptop is Vista but Windows 7, when I open it. So, after much research I found someone who said I should type collection in the area of research manager and allows to restore the laptop but unfortunately that does not exist in the laptop so I looked for something else and found out that by right-clicking on the computer that I can go to manage and then active partition and tried to restart. And then it happened, he showed "bootmgr is missing, press ctrl, alt and del to restart" so I did, but the same screen appears.

  I searched online again and said I need a cd of Vista or Windows 7, but I don't have that. They also said that it is the only way to fix the laptop. So now I'm out of options and hoping someone here can help me.

  Is there anyway I can fix this without the CD and restore my laptop to its original settings? Or can I restart my laptop without the bootmgr thing missing attachment?

  Really need help with this and your help will be greatly appreciated. Looking forward to the answers.

  Hello

  Try the following.

  If you do not, use another PC to create a rescue CD Windows 7.  Download the ISO relevant among the links below - if you are not sure, first try the 64 bit version.

  Windows 7 32 bit

  Windows 7 64 bit

  You must use an app like ImgBurn ( Note: you can deselect additional software during installation of ImgBurn options) to burn the ISO to a CD - a guide on the use of ImgBurn to write an ISO on a disc is here.

  When creating, type following the ESC key as soon as you start the launch of the laptop Boot Menu, and then insert the rescue CD.  Select boot options (usually f9 ), use the arrow keys to select the CD/DVD drive and press ENTER.  You can also get a prompt to "Press any key to" continuous - it if requested.

  Select the "Repair your computer" option and follow Option 2 in the guide on the link below to run the Startup Repair - you may need to run this 2 or 3 times.

  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  If the above does not help, take note of any error message you get during the procedure and include them with your next post.

  Kind regards

  DP - K

• Photosmart HP 6510 will only print black light gray text

  Any suggestions on how to solve this problem.  Been thro all the habit change the cartridges, clean the heads (several times), align the cartridges.

  Problem started after the low ink warning and then change cartridges.

  Need to BEST print mode to get the light gray black text only printer and printing grayscale value must be set to OFF, otherwise no visible impression is reached.

  Colurs look OK on the Test print but once again no sharp black, light not gray see the upward.

  Help please!

  Hi SportBilly15,

  Welcome to the HP Support forums.   I understand that your Photosmart 6510 is not printing black ink properly.

  I've included the document setting the streaks of ink, faded prints and other common print quality problems . It takes you through several steps to correct the problem of troubleshooting.

• Photosmart 6510 does not print in black

  My photosmart 6510 does not print in black. I presume that it was the cartridge but I replaced the cartridge and it still does not print. I cleaned the print heads and the cartridge ink levels are full.

  The printhead, cleaning of the screen failed touchscreen printer running.  But when I sat down at my computer and used the program utility printing, he did.  I ran an initial print head cleaning my computer and then clicking the button indicating that the print heads were NOT clean.  He then ran a deep cleansing process.  Then I lined up the printheads of the same print utility program.  Now it works!

• HP 6510 Photo Scan for MacBook fails

  I have a HP 6510, which worked perfectly with my old PC.  Yesterday I got a MacBook Pro OS X 10.7 Lion.  The printer is installed properly.  It prints.  It scans a document.   It does not analyze the pictures.  The result is an empty file, even if the HP it scans, says that it is finished and put it in the directory images on the MacBook.  There isn't any image

  Hello
  The default analysis workflows configured to scan 6 x 4 photo.

  Change the scanning settings to not crop the scanned area as follows, and are looking for any change, I think that this can cause the due blank image cropping:
  
  If you use Mac OS X 10.7 (Lion), make sure to install the critical update below, otherwise skip to the next step:
  http://FTP.HP.com/pub/softlib/software12/COL41827/MP-101648-1/HP_Scan_for_Mac_OS_X_10.7_Update.dmg
  
  Now change the settings as follows:
  1 open the HP utility and select your device.
  2. based on Scan Settings open the "Scan to Computer".
  3. click on the tab "scan tasks.
  4. Select the shortcut Scan allows to analyze, and then click on edit.
  5. in the section of scanning from an HP device, click the blue triangle to expand the menu.
  6. in the expanded menu now, open the drop down next to cultures in and set as none.
  7. click OK and try to scan the image.
  
  Kind regards
  Shlomi

• Black ink cartridge 564XL will work in the 6510 AIO printer?

  Black ink cartridge 564XL will work in the 6510 AIO printer?

  A cartridge of the same size that the color cartridge would be the photo cartridge.  This is not interechangable with the black cartridge, you will need a black cartridge.

  document here can help.

• Photosmart HP 6510: Black print failed

  I have a HP Photosmart 6510, which will not print black - pages of text, sound as if they are printing, but the page comes out blank. Watch as the color test page, but not black.  There is no error message.  Black print cartridge is full and I have applied all recommended maintenance procedures.  I'm going to disassemble the printer (which is out of warranty) and the print head to check the visible obstructions before deciding to give up completely and use my backup of Canon.  Can anyone suggest any other remedies or advice on removal of the print head?  Thank you.

  Thanks for your suggestions.  I removed and cleaned the print head, but the problem remains unresolved.  I did more research and decided to go deeper into the printer to access tubes empty below the print head.  I couldn't find all the instructions more complex procedure on the HP site or elsewhere online, so most of the work was intuitive.  I managed to remove the 'well' below the print head complete with 4 vacuum tubes, and it was immediately obvious to me that the black ink tube was clogged.  I went to clean the whole by immersing in hot water and using a syringe to flush out the tubes.  I cleaned too much ink frozen since sponges of drain that receives the excess ink from the vacuum system (no doubt mostly print head last cleaning operations).  After drying of the parts and reassembling the printer, everything is back to the fully functional State.

  I was amazed at the amount of vitriol expressed by users of the forum to HP for what seems to have been a recurring problem with these printers.  It seems incredibly useless to throw a sound mechanical printer because of a dried ink problem, but that's what many did the cost of 2-3 hours time technician to fix the problem simply cannot be justified. It is unfortunate that HP provides no instructions for technical people like me who are willing to undertake their own maintenance out of warranty HP products.

• HP Photosmart 6510 e - all-in on: print a picture

  I want to print on paper photo of android (Samsung Galaxy S6 edge).

  The printer is set to ask what tray. Nevertheless, it prints only on plain A4 of android.

  I used the build-in print function the and place paper 4 x 6 inches, the papertray photo value and finally used the application e-print and paper Photo Paper Type value!

  Any help would be appreciated!

  As I mentioned in the op, I tried the HP e-print application.

  But I found a solution, instead of choosing the Photosmart HP 6510 directly (with ip address), I chose Photosmart 6510 with l'[email protected].

  Apparently printing via hp service it does not accept the chosen paper size (4 x 6).

  It works:

  

  But it does not work:

  

  Any other suggestions?

• How can I create custom with the Photosmart 6510 printers paper sizes

  I want to use paper sizes personalized with Word or Photoshop.

  I have a Photosmart 6510 printer all-in-one.

  While I can find the custom size tab layout in Word and can set this size, I don't seem to be able give the new size a name or save it.

  Is it possible with this printer, or is there a workaround to avoid the message 'paper mismatch '.

  Thanks for the ay help I can get.

  I'm sorry not to come back earlier.  I stumbled across a work around for this problem.  Use a different print driver for the printer.  I'll link the instructions below.  Again, sorry I don't come back with the workaround as soon as possible.

  How to assign other drivers to print in different Versions of Windows

• PhotoSmart 6510 E: all-in-one Photosmart 6510 series is no longer able to connect

  I have recently inherited this printer and eventually got it working a few days ago. Now, I'm more able to print wireless from my computer.  My computer recognizes the printer and I have the ability to print with it, but for some reason any, he says: my printer does not respond when you try to print wireless from my computer. I can print by sending documents to the e-mail address of my printer, however. WiFi is configured and works according to the configuration page I printed.

  Any thoughts?

  Hey @reyn5013,

  Welcome to the Forum from HP Support.

  I understand that you are unable to print from Mac with your HP 6510 Photosmart e-all-in-one printer. I would like to help.

  I recommend you try the following steps:

  • Uninstall your printer - click here for instructions.
  • Fix permissions of the disc on your Mac - click here for instructions.
  • Once you have finished running the utility above, restart your computer.
  • Finally, click here to reinstall your printer.

  Please let me know the result of your troubleshooting by responding to this post. If I helped you to solve the problem and that you liked this post, feel free to give me virtual accessories by clicking on the 'Thumbs Up' icon below and by clicking to accept this solution.

  Thanks for posting in the Forum from HP Support. Have a great day!