A network of routers multiple wifi

Similar Questions

• Win 7 crashes when you use multiple wifi connections.

  Hi Shinmilla,

  I have a problem with Win 7. How did it crash the system when you use multiple wifi connections. How can I stop this from happening?

  Thank you.

  Hi Triode888,
   
  It is not recommended to have multiple Wifi connections since signals can be contradictory and therefore it crashes.
  You can't have several active Wifi connections at the same time.
   
  Also, I suspect it might be caused by your network wireless itself. It could be automatically connected to a network of 'death '. So please check that your wireless network is disabled or no if you do not use.
   
  You have installed VMware or Virtual PC?
   
  If so, these programs will create a new network - please open the network and sharing Center and disable these additional networks.
  
  1. open the network and sharing Center page in the control panel.
   
  2 confirm that it says multi-network right under the icon in the Middle, like the screenshot above.
   
  3. click on the link customize to the right of the first illustrated network, directly under the Internet icon, to display the window set the network location:
   
  4. move the window set the network location away, but let him open. (You'll need it in a minute, but at a time where it is otherwise inaccessible.)
   
  5. back on the network and sharing Center page, click on the link manage network connections (in the left task pane).
   
  6. in the network connections window, select the network adapter through which you get your Internet connection. (The views drop-down list, select Details; you want probably said something like network, unidentified in the status column.)
   
  7. click on disable this device network above (next to the big red X) button. Wait a few seconds for the chart on the network and sharing Center page to reflect the change.
   
  8. return to step #3 set network location window, and click on the merge or remove link network down locations.
   
  9. Despite Vista earlier assertion that he detected "multi-network," you will see probably only a single network in the window of merge or delete network locations:
   
  10. turn highlighted the only participant and then click on remove. (If there is more than one, you can delete all.)
   
  11. When you are finished, close the merge or delete network locations, and then close the window set the network location.
   
  12 return to the network connections window and with the adapter disabled network always highlighted the #6 step, click the option activate this device network (next to the big orange arrow) button.
   
  13. after 10-15 seconds of delay, your Internet connection should work now, signified by the absense of the treacherous of entries multiple networks in the network and sharing Center page:
   
  For more reference in http://social.answers.microsoft.com/Forums/en-US/w7network/thread/272b55ce-fb9a-423b-9a9a-8299f853cc29 look
   
  Aziz Nadeem - Microsoft Support

• I want to connect to multiple wifi networks, but with a unique wireless adapter?

  After much research on the internet I found a Virtual Wifi software that makes virtual adapters wireless with a single physical card. I download and installed this software but I don't know how to use it. There is no desktop icon or anything to change in my laptop.

  Can you please tell me some solution.

  I suggest you contact the software manufacturer for instructions on how to put up with your system.

  It should not be necessary buy additional routers.

  Eddieb

• Network: 2 routers Apple broadcasting separate wireless networks; one (Xfinity/Comcast) cable modem

  Hello community!  Need help, I want to use two routers to establish two separate wireless networks on a cable modem connection.  I searched for my answer and see some other threads on this topic, but all are either a bit too technical for me, are incomplete on the answers to my questions - and all seem to be locked.  I have also searched YouTube and only see videos to extend a network with two routers - not my goal.  So here is a long, but a detailed post on what I need someone help with - thank you very much in advance if anyone can all small-not me-I hope it will be useful to others in the future.

  The program installation/hardware: I have internet Comcast/Xfinity that runs to a Motorola surfboard cable modem (SB6141).  I also have two routers apple - a Time Capsule from Apple AirPort (to end 2013) and a new (2016) AirPort Extreme.

  Purpose: This is what I need--I need two separate wireless networks.  Before going further, by using the guest account and 5 GHz of a single router isn't an option for me.  I need to have both wireless networks separate (one of each router), do not talk to each other, or allow access between the two - the only is that they share the Comcast internet gateway.

  My plan is to have the cable modem Surfboard connect to airport Time Capsule, which will then connect to AirPort Extreme (even if it could be reverse - no difference, except that the data that I show below comes from the time Capsule, which is currently connected to the modem cable).

  To read the previous discussions, it seems that the starting point would be: modem router #1 Ethernet WAN, then a router cable #1 LAN Ethernet to the Router #2.

  First issue of clarification - the connecting cable should go to the Ethernet WAN port on the Router #2 or a LAN Ethernet port?

  Now that the first easy question is the road, I need help to configure two routers connected to allow two separate networks.  A lot of discussions about the positions of static IP addresses, cascade, etc..  I need specific help with AirPort Utility on what to change on what router.  It seems obvious that the settings under the 'Internet' and 'Network' tabs are those who need to set - the 'wireless' tabs simply treats the name of the wireless network and settings - these, at least I can understand!

  I'll organise this tabbed - here go us.

  First of all, the "Internet" tab/window Airport utility. Here are the options:

  Connect using: Router #1 has currently DHCP (which I think is OK?) What should it be set to Router #2?

  This tab lists also the current address in IPv4, the (255.255.254.0) subnet mask and the router address.

  It has grayed out information in the boxes for the DNS servers; Name of domain and DNS IPv6 servers.  At the bottom of the window, there is an IPv6 Internet WAN address listed.

  If I click on the "Internet Options" button at the bottom of the window, it takes me to the 'Internet Options' window. Here, there are various IPv6 information - it seems that I can choose the configuration of IPv6 and the IPv6 mode using the drop down boxes/selections were also chosen.  There is also a checkbox 'Enable IPv6 connection sharing'. Are the current settings for these for Router #1: configure IPv6: automatically; IPv6 mode: Native; and check/yes to enable sharing of IPv6.

  Next up, the 'Network' tab utility AirPort/window.

  Here, there is a drop-down menu "Router Mode", a DHCP range listed, and the ability to add or remove reservations DHCP and Port settings.  The DHCP range listed for Router #1 is 10.0.1.2 to 10.0.1.200.  There is currently no reserves DHCP or specified Port settings.  Finally, there is a checkbox to the bottom to "Activate the access control" - it is not currently checked/enabled.

  If I click on the 'Network Options' button at the bottom of the window, it takes me to the "Networking Options" window Here I have areas of entry to specify the DHCP lease duration, can specify the DHCP IPv4 range, as well as part of the extended DHCP IPv4 comments.  There are checkboxes: enable NAT Port Mapping Protocol. Select the host by default (with input if selected text box); Enable the IGMP Snooping; Block incoming IPv6 connections; Allow the Teredo Tunnels; and allow inbound IPSec authentication.

  For this window, here is the current settings on the Router #1:

  DHCP lease is 1 day; Beach DHCP IPv6 is 10.1.2 to 200; Hosts IPv4 DHCP Range is 172.16.42.2 to 200.  The following check boxes are enabled/checked: enable NAT Port Mapping Protocol. Block incoming IPv6 connections; And allow inbound IPSec authentication.

  Who can help me? What parameters, if all do I need to change the #1 router?  How to set up router #2 to make a second wireless network?

  Purpose: This is what I need--I need two separate wireless networks.  Before going further, by using the guest account and 5 GHz of a single router isn't an option for me.  I need to have both wireless networks separate (one of each router), do not talk to each other, or allow access between the two - the only is that they share the Comcast internet gateway.

  What you really need is a combination router / Ethernet switches that s supports VLANdedicated. Given that Apple routers do not, at best, you can potentially get the results that you are looking for, but at a performance cost. In other words, you can have two separate WiFi networks where clients connected to a network can not 'see' those related to another and both routers will always provide access to the Internet through Comcast modem. Note: Arris / Motorola SB6141 isn't a gateway device. Instead, it's a simple modem. A gateway is a router modem combination.

  To do this, should do the following:

  • The Time Capsule (TC) would need to be directly connected to the modem using an Ethernet cable. This base station would remain in its default configuration of the router. In other words, the router Mode (in AirPort Utility) would establish: DHCP and NAT.
  • AirPort Extreme would be directly linked to TB by Ethernet. The cable must be connected to one of the LAN ports on the TC on the WAN port to the extreme. It must also be configured as a router. However, there are differences in the extreme:
    • Use a different name to the Wi - Fi network.
    • Use another range of IP DHCP address. By default, Apple base stations use IP addresses in the 10.0.x.x range. I suggest that you set the base station of the second on 192.168.x.x range.

  There is a major drawback with this configuration. The second base station will be in a State of "Double NAT". Although this "separating" the two networks on different subnets, this condition is not very effective and connected to this network of customers will get lower throughput performance. There is no way around it and it is not recommended.

  First of all, the "Internet" tab/window Airport utility. Here are the options:

  Connect using: Router #1 has currently DHCP (which I think is OK?) What should it be set to Router #2?

  The two should be: DHCP.

  This tab lists also the current address in IPv4, the (255.255.254.0) subnet mask and the router address.

  These leave it as what. The TC is information of IP address of the modem. The extreme, he'll get the TC.

  It has grayed out information in the boxes for the DNS servers; Name of domain and DNS IPv6 servers.  At the bottom of the window, there is an IPv6 Internet WAN address listed.

  These leave it as what.

  If I click on the "Internet Options" button at the bottom of the window, it takes me to the 'Internet Options' window. Here, there are various IPv6 information - it seems that I can choose the configuration of IPv6 and the IPv6 mode using the drop down boxes/selections were also chosen.  There is also a checkbox 'Enable IPv6 connection sharing'. Are the current settings for these for Router #1: configure IPv6: automatically; IPv6 mode: Native; and check/yes to enable sharing of IPv6.

  Unless your ISP provides your IPv6 service, change the IPv6 configuration option to: 'Link-local only' on two base stations.

  Here, there is a drop-down menu "Router Mode", a DHCP range listed, and the ability to add or remove reservations DHCP and Port settings.  The DHCP range listed for Router #1 is 10.0.1.2 to 10.0.1.200.  There is currently no reserves DHCP or specified Port settings.  Finally, there is a checkbox to the bottom to "Activate the access control" - it is not currently checked/enabled.

  Router mode should be: DHCP and NAT to two base stations. Ignore the DHCP reservations and Port settings for now. Let the current DHCP range for the TC. Change the DHCP range for extreme for: 192.168.1.2 a.200. At this point do not access control for each base station.

  Since you seem to need the step by step instructions or need help to understand the different terms networking, I highly recommend that you help you to become familiar with networking, specifically on Apple systems. I suggest you consider taking the e-Book to the next control: take control of your Wi - Fi Applehttps://www.takecontrolbooks.com/apple-wifi network

• Satellite A100-495 - Intel 3945abg wireless network card cannot find wifi networks

  Greetings,

  I have some problems with networks wireless on my laptop Satellite A100-495.

  The problem is: my wireless adapter (intel / pro 3945abg) doesn't seem to find wireless networks. If I portable place very close to my router wireless (such as 1 m) - connection can be established. If I move away (~ 5 m)-no connection or 'very bad' quality and constantly broken. Other notebooks I've tried still have "very good" quality at the same range.

  This happens with other routers as well. And I can not any sign of wi - fi in my Uni (my colleagues have no problem with their machines).

  I tried to play up with some parameters. Reinstalled adapter. Downloaded the latest drivers. Nothing helps.

  A tip? Thank you in advance.

  Hello

  Something like that happened to me a long time ago.
  I used the Wlan configuration option to own Windows. For several months, I use the Intel Proset configuration utility to establish the WiFi connection!
  It works!

  In addition, I have disabled the power Wlan option in the Wlan card properties save and adjust the intensity of the signal at top. I remember, in the advanced properties, you can find the 802.11 option preamble. The value is Long and short on my laptop.

  Hey dude... Check it out.

• How can I remove networks unwanted in my wifi network list?

  I am new to Mac computers; I'm fine with PC. Just got a new macbook air. My problem is with the wifi. I put my home network password wifi prefer network, but it is still not as preferred. Have to retype whenever the computer goes to sleep. I would delete the network unwanted in the network list. How can I do this?

  Go to System Preferences > network > advanced > Wi - Fi.

  Drag the networks in the order you prefer.

• Network configuration of Roaming Wifi problem I just bought an Airport Extreme and I intend to use it as my router

  I just bought a refurbished Airport Extreme and I intend to use it as my router & combine with our old time Capsule of existing one to create a roaming Wifi network.

  The new Airport Extreme (renovated) is in my studio/Office - directly connected to our internet broadband wireless (WAN port)

  Our small ethernet is connected to my iMac [mid 2010 running OSX 10.11.5] & a PC and extends up to 2 other domains through an ethernet switch.

  This configuration works very well, our internet speed has improved slightly - better than our old T-Link router bit.  WiFi available throughout the House - better on one side.

  Time Capsule (2 TB) is connected by ethernet on the far side of the House, offer backup Time Machine and strong Wifi to this area.

  This time Capsule was an existing installation that went perfectly with the T-Link before I bought the Airport Extreme.

  I used the Airport utility to set everything up and it seems to work.

  The problem is:

  Combines the Capsule and extreme connected & active, the Internet gradually slows down and grinds to stop. -Wifi seems to follow suit, but is much more gradual.

  If I disable the Time Capsule, the internet connection is back to normal, Airport Extreme Wifi signal is strong and extends to almost all areas.

  I got to the departure of the two units configuration problems, so I reset both factory default and from that moment managed to do all this work - with the exception that the internet connection slows down.  Whenever I visit a different web site, it takes more time to load/link upward.

  I spoke with our ISP, the link to our tower is solid. The technology suggested that I put Wifi on each unit to use a different channel (2 frequencies & several channels each available).

  So far, this has not resolved the problem, I will continue to make adjustments.

  I googled this - most of the answers are not to date - usually 2012, 13, 14. and not directly related to my situation.  But I will continue my search.

  I'd appreciate if anyone here has any suggestions

  The new Airport Extreme (renovated) is in my studio/Office - directly connected to our internet broadband wireless (WAN port)

  What is the number and the model of the modem or modem/router that your ISP has provided you?

  Should we assume that you use a Mac with the help of a current or recent operating system?

  If you get out of the Capsule of time and leaves disabled for now, the network AirPort Extreme continue to run at full speed for a few hours and not slow down?

  We ask these questions because we must first confirm that the AirPort Extreme works properly until we can begin to troubleshoot the connection to Time Capsule.

• do not print to the printer wireless network computers connected to wifi

  Don't know if I'm in the right Forum but here goes.  I work in a dealership service department. I have 4 computers connected to our network. I just bought a pro m426fdw mfp laserjet 4 in 1 ad printer connected to our wifi system because there is no available ethernet jack to connect to the main network. Is there a way to allow my 4 computers send information about this printer wireless?

  If you connected to your wireless network, and then run a report of network printer and find the ip address of the wireless connection. If you're in the list use to load the printer using add it printer, the local printer, create a port and the menu drop-down, choose standard tcp/ip and then follow the instructions on the screen. You can also try to load the disc that came with the printer and see if it will find the printer and load it for you.

• Establishment of a network without internet connection wifi

  I'll set up a wifi network in a place WITHOUT an internet connection.

  I have an Airport Express to the location and my MacBookAir.

  I have a Samsung smart TV in the place and I would like to use it to watch the content on my laptop (iTunes and elements in the movies folder), but can't find a way to do it. I tried an AppleTV 3rd generation, but which will not work because it requires an internet connection to complete upward. I'm not having luck with Airplay or mirror screen either. I tried a Thunderbolt/HDMI converter and I can get the picture on the TV, but the sound comes through my laptop. It is annoying because the TV is connected to a decent sound system.

  The TV has two HDMI ports, one for the cable/satellite and one for a DVD player (MHL / DVI). It also has an ethernet port and a USB port.

  I would like to * fine * want to stream from my laptop to my TV, but if I can't do that, I'll do it, installs for all cable set up will get the video and audio into the TV. Y at - it a box of streaming that doesn't require Internet?

  Welcome suggestions, especially if they are in basic English, I'm really bad at the net jargon.

  Thanks in advance!

  You can be very sure that other people have tried.

  Solution of workaround for apple tv without an internet connection?

  Just using a tethered phone or even dial-up internet so that DRM can work would help.

  http://physedagogy.com/2014/09/25/no-Wi-Fi-no-problem-using-Apple-TV-to-mirror-y our device without wifi.

  A lot of blogs on this topic and a lot of useful info in some of the answers.

  Y at - it a box of streaming that doesn't require Internet?

  Loads of them... look for the Plex.

  The problem is (most legitimate at least) media sources tend to put a priority on the establishment of copyright law.

  I tried a Thunderbolt/HDMI converter and I can get the picture on the TV, but the sound comes through my laptop. It is annoying because the TV is connected to a decent sound system.

  Switch sound on hdmi.

  IA-Thunderbolt-HDMI-connecting-to-HDTV http://Apple.StackExchange.com/questions/92493/How-can-i-Troubleshoot-no-audio-v

  Again, you are not the first to have the problem... loads of experience if you googled around to find out how to get his work... or if the laptop is a model then it might be impossible.

  Apple makes things difficult when you don't have internet... it is just to have a tethered phone and really just do the little bit of work involved in the installer... or the same 56 Kbps dial-up modem.

• network controller pci, drivers wifi device does not

  my model is dv6-6121tx

  I'm not able to install network controller and PCI device drivers...

  also my wifi does not work...

  no adapter in Device Manager wireless...

  Help, please...

  Hello again.
  
  The computer initially has Windows 8?
  
  First, download the following drivers.
  
  Here is a link for the driver Broadcom Wireless LAN for Windows 7.
  Here is a link to the Realtek PCI Card Reader for Windows 7.
  Here is a link to the HP Quick Launch Button for Windows 7 software.
  
  Now, you will need to remove the previous drivers before installing these.  Try the following.

  1. Click Start, type "Device Manager" and press ENTER.
  2. Right click on each of the devices that you listed above and select 'uninstall '.  If you are prompted to remove driver and driver package.
  3. Quit Device Manager and install the three drivers that I posted above.
  4. Once all three installed, you must restart your laptop.
  5. After Windows loads, you must again visit the Device Manager and see if the exclamation points are gone.
  6. Check that the equipment works and post the result.

  If you find this useful or want to say thanks you can click the White Star under my name to give me congratulations.  Also, if this solves your problem make sure you mark the post as solved.  This makes it easier for other users to find answers to their questions.
  
  I'll keep an eye out for your answer.  Have an amazing day.

• How to remove several networks in the Smart WiFi Linksys

  I hope this is the right place to ask this question, if not please me foregive. I recently replaced my router with a WRT1900AC and after installation, I use my account for smart wifi Linksys to the Manager of this router that I used with my old Linksys router. However, when I noticed two other networks listed as to connect to networks of connection. They do not connect what either and I think that they are of my old router (I used the same network name). How do I remove these? They do not seem to be causing the problems, but are confused. Thanks in advance for any help!

  Ken

  Hello! Articles on the following link will help you remove the existing networks on your computers, portable devices or game consoles: http://www.linksys.com/us/search?text=remove%20networks&type=support_faqs

• To connect to a network using Microsoft Virtual WiFi Miniport Adapter

  I have a laptop windows 7 and I found the so-called map of Microsoft Virtual WiFi Miniport, I don't know what it's for, but I don't know that it's a virtual wireless card.

  But I can't connect to a network to use it. and I don't know how to connect to a network.
  I DO NOT have any errors, but I just want to know what it's for. :-)
  Thank you.

  Its uses the wireless function integrated hostednetwork that transforms your computer equipped with wireless (WiFi) in a wireless router/access point. I use this feature to connect an iPod Touch (4th generation) wireless internet via my laptop while traveling in places where there is no wireless internet access, but it is wired internet access, IE. to some hotel/motels for example.

  The adpater is not normally used to connect to wireless networks. This work is for your hardware integrated wireless (WiFi).

  http://Windows.Microsoft.com/en-us/Windows7/view-and-connect-to-available-wireless-networks

  Interface based on FWIW you can make use of the hostednetwork function by configuring using netsh wlan set hostednetwork of command line commands or use free programs such as Connectify and virtual router that uses a graphical interface.

• HELP blackBerry Smartphones: I BIS, but BBM and Gmail only works on network and NOT on wifi

  Hi all, sorry in advance if this problem has already been postponed.

  I myself recently had a bold 9900. Everything worked well, but I met a pretty big problem which I spent hours looking for fix on the internet today, but nothing helped. So I decided to make an account on here to see if anyone can inform me personally with a solution. My carrier is O2 (UK), but I use the sim card while living abroad in Czech Republic. I don't meet with this problem on my previous BB (torch).

  I buy a monthly BIS data plan and it is still active at this moment - it is clear from "EDGE" that appears at the top right of my screen when the network is enabled or "3 G" (with the blackberry icon) .
  When the network is running - my BBM, Twitter/Fb apps, Gmail, browser all works fine (as it should) because of my BIS.

  The problem:

  Once I turn the networkand activate wifi WE, my BBM and Gmail work & the BB icon disappears from the top corner, instead of move slightly down to accompany the icon of intensity of the wifi (which would always be the case on my previous BB) right.

  What is even more strange, given that BB icon is still missing, is that my BB Facebook and Twitter apps still work fine with wifi on, just like the Explorer... So why not BBM and Gmail?

  (Which makes me ask: I thought that the BB Facebook and Twitter apps necessary BIS to work?)

  Anyway, once I enter the 'wireless network' > menu > 'Troubleshooting' > "Wifi diagnostic", the following errors are displayed:

  (1) UMA connection error. Status: Error of wireless network

  (2) infrastructure blackberry connection error.

  I tried to return the directories of service, which made no difference.

  Help, please!

  Well Yes, I tried yesterday (restore to factory wireless settings) does not. I have now restored the mobile to factory settings and I'm relieved to say that the BIS now works just the wifi.  

  Thanks for your advice anyway.

• BlackBerry Smartphones can not play youtube video with the 3G network, but works with WiFi, why? Help, please!

  Hello

  I tried several times to read the youtube videos with network wifi and it works fine, but when I use the 3G or GPRS nework to play the video, it first to ask "Switch to WAP for streaming media? (with wifi that he won't ask) so I press ok and it uptempt to load and an error message "content not available. Server is blocked or unresponsive. ", it goes with all the videos I click on that. Help, please.

  Thank you

  Let me share my personal experience on the subject. When they are facing the same problem, I asked my provider and they tried to pull a fast explaining that viewing videos on the 3G network is dependent on the device and that it is not possible to videos on my BB "BOLD" due to speed issues. They even suggested that I buy an iPhone 3G given that subscribers who do not seem to display YouTube videos problems. A load of rubbish! After only a brief workshop organized by RIM and my career, I was "unofficially" informed by a member of staff that it was a TCP/APN issue. I take advice, made the necessary adjustments, and was able to view Youtube videos on the 3 G network without problem. However, my Bill the next month floored me. Even if I'm on a package data unlimited, I was charged an extra $ 70 on top of what I usually pay. Learn more with my carrier, they were kind enough to inform me that I have to access the Internet via their APN address, which translates into a lower speed of AFN, orI will have to pay for accessible data on the other addresses of the AFN. I supported with my questions and my carrier eventually admitted that they were actually limiting the speed on AFN as allowing only some mobile devices to access data at 3G speed. Then you tell me!

• 'unidentified network' but connected to wifi

  When I try to connect my laptop to the modem wifi then wifi is connected but internet cannot be 'unidentified network' access appears please help me I have tried almost every possible change.

  Hello

  1. it all the troubleshooting steps you have done so far?

  2. what happens while you are trying to access the internet?

  3. what browser you use to access the internet?

  4 have have there been recent changes made on the computer before the show?

  Please follow the steps below and we update with the results.

  Method 1: Run the network troubleshooter, and check.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2: Please try following the steps provided in the article and check out them.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Let us know if it helps!