A satellite starts no-Windows cannot start

Similar Questions

• Satellite Pro A200: Windows cannot find WLan

  Something is wrong with my laptop, I have Toshiba Satellite Pro A200 with XP Pro SP3...

  When I try to search for wireless networks using the Microsofts, he found nothing, but can from TOSHIBA ConfigFree.

  You're probably, who has to use Toshiba then - software is not possible, cause ConfigFree supports the WEP keys, but most of the keys used here wireless are WEP - TSK or something - not supported by ConfigFree.

  How can I make my Microsoft Windows to detect wireless routers?

  Have you tested without SP3?
  Many people here have reported on the various problems after installing SP3.

• Satellite M30: Windows cannot start because a file is missing

  Error message: Windows cannot start because a file is missing.
  \Windows\system32\config\system

  You can repair from ordinary cd and use "r" for repair.

  How to use recovery cd for this... It does not work.

  Hello

  It's not easy to use the repair mode because the recovery image file CD. The other way is that you try to start the operating system is the safe mode and look if the lack of files exist in the C:\I386 folder. If not, well I think that the only way is to recover the system with the recovery CD.

  Good bye

• HL-DT-ST DVDRAM GT80N "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  I ran provided patches I've uninstalled and restarted. Attempted to update the drivers. I can not get my DVD/ROM to work I have a Toshiba Satellite S855 S5381

  "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19) »

  HL-DT-ST DVDRAM GT80N

  I have windows 8

  How can I erase my registry and start all over again? What exactly I'm looking for?  I found a post for the same problem on a different model, but I can not located what was discussed.   My computer has been used since the beginning of February.  I need to install programs and others.

  I have fished all day found this and it fixed it!

  http://support.Microsoft.com/mats/hardware_device_problems

  Thank you for your help :)

• Satellite L650D-10J - Windows 7 does not start

  Hello

  I have a Toshiba Satellite L650D-10J, Windows 7 64 bit, 4 GB RAM and it do not start Windows 7. He begins to see you logo startup Toshiba etc and then it goes to black and it loads Bootmanager of Windows with the following message;

  + A problem on your computer has occurred during communication with a device that is connected. +

  + This error can be caused by an external storage device as a drive external USB, the device in use, or damaged hardware such as a hard drive or CD-ROM drive disconnect that is damaged. Make sure that all removable storage is properly connected, and then restart your computer. +

  + Contact the hardware manufacturer, if you still see this error. +

  + Status: 0xc00000e9 +.
  + Info: an unexpected I / O error has occurred. +
  (it has been translated by the Dutch there are some sentences that are incorrect.)

  I tried to download a Windows 7 recovery disk, it burned on DVD. It works, I'll get to choose where he was working to correct (I get an error) or use a Windows 7 from disc (does not work). And if I start it in safe mode I see that it stops and freezes to the file; Disk.sys

  Someone at - it an idea?

  Greetings,

  Hello

  And have you connected an external USB device as says the error message? If Yes, remove all USB devices and try to restart your laptop.

  If you can t start in safe mode, your operating system is confusing upward and the only option to get rid of it is to reinstall Windows.

  You use the preinstalled version of Windows 7 in Toshiba? If yes go to the start menu Windows by pressing the F8 button where you can select the safe mode, etc. and choose Advanced repair my computer option. Then select Toshiba HDD recovery and factory settings are restored. Also see this article on HARD drive recovery:
  http://APS2.toshiba-tro.de/KB0/HTD1303440001R01.htm

  If disk HARD recovery doesn't work, you need an original Toshiba recovery disc. If you didn t create this drive just order a new one here:
  https://backupmedia.Toshiba.EU/landing.aspx
  ?

• CD/DVGW SN - S082D question - Windows cannot start this hardware device Code 19

  I've had my laptop for a little over a year now and it's had its fair share of problems, which most is repairable or there is a solution.
  Earlier today, I inserted a disc in the drive and tried it opens, went into "My Computer" and find the disk was not displayed.

  It's happened a couple times and a simple reboot fixes the problem.
  I rebooted twice and this time, that the problem was not fixed, after going in 'Device Manager', I found there was a problem with the device and he gave me the following error message

  "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  As usual "search for the solutions" is useless and doesn't return any results.
  Thanks in advance for any response.

  Some info that may help
  OS: Windows Vista editions Home Premium
  Laptop model / number: Medion MD 98300
  DVD drive: TSSTCorp CD/DVD W SN-S082D ATA Device

  Thank you

  First of all, I wonder why you post this here in the Toshiba forum if you don t have a Toshiba laptop
  It's a little strange for me... anyway I'll try to help you.

  It seems that the registry keys are corrupt and so your CD/DVD drive does not work properly.

  Just try the proposed solution mentioned here in the doc of Microsoft:
  http://support.Microsoft.com/kb/270008/en-us

  Good luck

• I reformatted my T520 with the recovery disk, but Windows cannot start

  I reformatted my T520 with my recovery disk. When the computer restarts, it says that Windows cannot start properly. Help, please.

  I finally solved the problem; Here is my solution:

  I have determined that the backup image has been bad, and this is perhaps why the recovery disks have been as bad. I tried to use both to reformat the C:\drive several times without success. Fortunately, I had a Windows 7 disc from another computer that I no longer use. However, the T520 would not be updated to Windows 7 using this disk, so I run Diskpart to reformat all (this removes everything, including the image.) Then, I was able to reinstall Windows 7.

  With this new facility, would not any responsible drivers, including LAN and wireless drivers. I went on the Lenovo Web site: http://support.lenovo.com/en_US/downloads/default.page?selector=expand to download the driver for "Intel Wireless LAN (11abgn, abg, bg). This provided wireless access to the computer. (Downloaded the driver on another computer, saved on a USB stick to transfer to the T520.) Restarted the computer in case where. Then, I went to http://support.lenovo.com/en_US/detail.page?LegacyDocID=TVSU-UPDATE to download ThinkVantage System Update 5.0. After you have installed this software and reboot, all the necessary drivers would be so loaded.

  Unfortunately, if you don't have any Windows disk, you will need to pay 50 dollars to get one from Lenovo. Lesson learned? Next time I buy a new computer, the first thing I would do is to reformat and reload the computer by using the image while still under warranty. I did several times with my other Lenovo laptops without fail. I have to do this once every 3 years each time my computer seems to slow down. This is the first time, it didn't work.

  I hope this help anyone who is in the same situation.

  (Boy, I have miss the good old days when I could fix everything from the DOS command prompt.)

• When I start my computer I get this error message: Windows cannot open this file: GLBD4EA.tmp

  When I start my computer, I get this error message:

  Windows cannot open this file: GLBD4EA.tmp

  To open this file, Windows needs to know what program you want to use to open it. Windows can go online to look for automatically, or you can manually select from a list of programs installed on your computer.

  What do you do?

  -Use the web service to find the appropriate program
  -Select a program from a list of installed programs

  No selection works for me. I don't know what concerns the .tmp file, or why I need to open it.

  Please help :)

  Hello

   
  Perform the following steps to remove the file from the registry.
  a: type regedit into the search box start and click on enter.
  b: Search now to the following key
  HLKM\SOFTWARE\Microsoft\windows\currentversion\run
   
  then delete the following key
  53E412B3-9907-4F9E-A6DC-D0106D1D72C
   
  Important:  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information
  However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  322756 (http://support.microsoft.com/kb/322756/)
   
  Hope this information helps.

• Windows cannot find C:\WINDOWS\system32\rundll.exe. Make sure you typed the name correstly and then try again. To search for a file check the Start button and then click search.

  I tried to launch my Spysweeper and found that is not there, then I re downloaded and I could not install it because it was already on my computer.  I went to the control panel to remove and got the message:

  Windows cannot find C:\WINDOWS\system32\rundll32.exe.  Make sure you typed the name correctly and then try again.  To search for a file, select the Start button and then check the search...

  What should I do?

  Hi gsrow,

  You can go there!

  Cannot find the Rundll32.exe file when you open the control panel:
  http://support.Microsoft.com/kb/812340

  Alternatively, copy the folder C:\Windows\System32\DllCache Rundll32.exe file to the System32 folder. Ramesh Srinivasan, Microsoft MVP [Windows Desktop Experience]

• Error: "Windows cannot start the windows firewall/internet connection sharing (ICS) service.

  On my Eee PC under XP Home edition tablet, I get the error "Windows cannot start the windows firewall/internet connection sharing (ICS) service" when I try to access my firewall. I also can't connect to my router Wireless Lan to go on the internet. This may be due to some viruses that have been deleted using Microsoft Security Essentials.But the problem persists. Could recharge SP2 solve this problem or am I condemned to reload the operating system?

  Hi jdmanel,

  NOTE: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://support.Microsoft.com/kb/322756

  Follow the steps in the article.

  You cannot start the Windows Firewall service in Windows XP SP2

  Troubleshooting settings of Windows Firewall in Windows XP Service Pack 2 for advanced users

  For reference:

  How to manually open ports in Internet Connection Firewall in Windows XP

• Installed wireless Belkin, unable to see network, get error windows cannot configure this wireless connection and starting the WZC abuse

  Hello

  I have a belkin wireless router that worked on my primary computer and a portable computer for years.

  Recently, I moved my main computer and now it dosnt seem to work. Belkin is installed but when I ask to see available networks, it says that windows cannot configure this wireless connection and starting the WZC abuse. Belkin still works fine on my laptop so I know no there is not a problem here. Can someone help me please? I tried to type in %SystemRoot%\system32\services.mcs\s as with a question of people, but all I get is windows can't find this.

  Any ideas please?

  Thank you

  * original title - Help... problem with belkin wireless *.

  Let's see if I can cut through it.

  You wrote:

  Click the Wireless Networks (see this picture) - I did

  Is the box 'Use Windows to configure my wireless network' checked or unchecked? There is no such box.

  I connect using - he says belkin. another box saying this connection uses the following items. then underneath there are 3 tabs - install, uninstall and properties. If I press on properties it says name provider and in this box, it says windows index.

  It seems that you don't have not clicked the "Wireless networks" tab, after you open the properties of your wireless adapter.  From your description, you look at the 'Général' tab: click HERE to see the "Général" tab Click HERE to see the 'Wireless Networks' tab.

  There are 5 columns: name, description, status, startup type and log as.  The values for the last 3 columns should be started, automatic and Local System - on my screen there are 4 tabs at the top - general, connect you, recovery and dependency.

  You skipped a step... 5 columns are in the 'Services' window initial... you arrive at "4 tabs at the top", AFTER you double-click the Wireless Auto Configuration.

  Status of the service which includes 4 boxes. stop suspend and resume. the button highlighted in the start menu

  Just to the right of the expression "Service status", you should see a Word.  On your system, this word probably is "stopped."  The 4 buttons (boxes) are how to control the service.  Because you said that the highlighted button is 'start' which means that the service is currently stopped, and you will need to click on this button "start" to start.

  I strongly suspect that you had used the Belkin utility to control your adapter - and now, you also started WZC.  As I wrote above, you can have both running at the same time.

  When you click the icon of your "Belkin", do you have a screen that looks like this: http://www.wi-fiplanet.com/img/2006/belkinn1/08.jpg

  If so, you should return to the utility Services and 'Stop' the automatic configuration service.  If you want to use WZC instead of the Belkin utility, see http://en-us-support.belkin.com/app/answers/detail/a_id/40/related/1

  I'm not familiar with the Belkin Wireless networking utility, but many wifi manufacturer utilities can be used to turn your wifi on and off, then maybe your was off (the adapter on your computer - not the router).  If you identify the model of the card you have in your main computer, I'll see if I can find the manual on the Belkin website and maybe give you a little more information.

• mouse works does not, his hang.its showing me the error like this. "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged (code 19).

  I recently installed a graphics card for GTA 4, his work properly.bt yesterday my screen crashed it mean clear.when I started in safe mode then it is appeared correct.afterwords all of a sudden my mouse kick & stopped then I uninstalled graphic card.cause of this my connection net failed.plz help me & give me good solution.i have window xp.

  Hi DineshKaria,
  
  This can occur when more than one service is defined for a device, if there is a failure opening the service subkey, or if the driver name cannot be obtained from the service subkey.
   
  Follow the suggestion in the article given below for code 19 and check if the problem is resolved.
  Explanation of error codes generated by Device Manager in Windows XP Professional
   
  Additional reference on:
  Code 19: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged

• XP to start, get the message "Windows cannot find C:\WINDOWS\System32\Tools\DelFoders.exe".

  When I start my computer, apearing this message Windows can't find C:\WINDOWS\System32\Tools\DelFolders.exe

  What can I do?

  Although what follows is 5 1/2 years, it looks like something, you should study.  Look for the message by "Savel'evna" part to the bottom of the page: http://www.pcreview.co.uk/forums/windows-cannot-find-c-windows-system32-delfolders-exe-message-t532088.html

• DVD/CD Rom error: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19).

  Original title: CD-ROM/DVD-Rom problems

  My CD-ROM/DVD-Rom drive does not work when I check the system, I get the following message "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19). "How to solve this problem?  Thank you in advance.

  Try following the steps under "Windows 7 or Windows Vista" in the MS KB article:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• HL-DT-ST DVDRAM GSA - T10N ATA Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  Hello

  My DVD/RW drive stopped responding on my Acer Aspire laptop computer 4510Z I checked the Device Manager which is gives the following error message:

  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19) Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

  I solve this error so far achieved the following without success:

  -Checked for solutions using the button below the error message
  -Scanned for hardware changes
  -Used Microsoft Automated Troubleshooting Service (SMAT)
  -Created the cdfix.reg file, it has added to the registry and restarted the computer

  I would be so gratefull for any help anyone can offer.

  Darylandgoats

  Hello

  I oddly found the solution to my problem while browsing through the suggestions of SpritX at the following link: http://forums.techarena.in/vista-help/771598.htm

  Here is the solution I implemented and now my drive works perfectly:

  RESOLUTION
  Warning serious problems might occur if you modify the registry incorrectly by using the registry editor or by using another method. These problems may require that you reinstall the operating system. Microsoft cannot guarantee that these problems can be solved. Modify the registry at your own risk.

  To resolve this problem, remove the affected filter drivers. To do this, follow these steps: 1. Click Start, type regedit in the search box, and then click regedit in the list programs.

  If you are prompted for an administrator password or a confirmation, type your password, or click on continue.
  2. Locate and then click the following registry subkey:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
  Be careful it can be many instances of the registry subkey that is mentioned in step 2. You must ensure that you are in the appropriate registry subkey before modifying the UpperFilters and LowerFilters values. To verify that you are in the appropriate registry subkey, make sure that the default data value is the CD-ROM/DVD-ROM and the class data value is CDROM.
  3. in the right pane, click UpperFilters, and then click on remove.
  4. click on Yes to confirm the deletion of the UpperFilters registry entry.
  5. in the right pane, click LowerFilters, and then click on remove.
  6. click on Yes to confirm the deletion of the LowerFilters registry entry.
  7. exit the registry editor and then restart the computer.
  Note When you delete the UpperFilters registry entry and the LowerFilters registry entry, you may lose functionality in certain programs such as CD recording programs. In this scenario, you must reinstall all of the programs involved. If the problem persists, contact the program vendor to determine if an update is available for the program.

  For information about how to contact computer software vendors, click the number in the following list to view the article in the Microsoft Knowledge Base:
  65416 (http://support.microsoft.com/kb/65416/) hardware and software contact information, A - K

  60781 (http://support.microsoft.com/kb/60781/) hardware and software details, L.-P.

  60782 (http://support.microsoft.com/kb/60782/) hardware and software contact information, Q - Z

  Thank you!