A520 forget date

Similar Questions

• How to read data from a worksheet to a chart in the form of wave at intervals to simulate real-time data

  Hi I have measured data using a SELF-DIAGNOSIS device and that you have downloaded the log files as a .csv I have attatched below.  I'm trying to read the 7th column of data (RPM) and display it on a waveform graph, read line-by-line to simulate driving real-time data. The interval between readings, I'm trying to achieve is 500 Ms because it is the time interval of readings on the worksheet. I'm finishing the two loops when rpm is equal to zero, as happens when the car is off. I have attatched the relevant section of my program below. Any suggestions would be greatly appreciated.

  Thank you

  Michael

  There are two errors in your block diagram.  First of all, as you read the entire table 2D in all at once (which is fine), you make a clumsy (pardon my language) job to make a line of programming.  Once you take the first line of headers, you have the ideal substrate for a loop, which is made of elements of an array (lines) process, one at a time, using its tunnel of indexation.

  The second mistake is to forget data flow.  The loop, I mentioned, or the While loop you use, produced one at a time and points it at 2 Hz thanks to your expectation of 500msec.  You want to give each point to your chart, but the picture is out of the loop, which means that there is No point until the loop ends.

  Here's an easy Question - where you put the indicators in table of waveform?  [Council - I said that "outside the loop is bad"].

  Bob Schor

• Drive Blu - Ray won't remember Netflix login

  I just bought the: Sony BDPS790 Blu - ray player 3D with Wi - Fi, which cost me a small fortune ($250).
  I have only had it a few months, and already he has stopped to remember my Netflix login information. Now, I have to use the phone on my TV screen button to reenter the login information over and over again. This is quite ridiculous. Why so complicated? Why it's just usually don't forget data! It worked fine; now he doesn't. What the devil you all do? Your last update screw everything up? When are you going to remedy! I'm completely sick of returning my login information. Fix as soon as POSSIBLE or give me a refund. This player is undesirable more and more apparent to be just not support $ 250 piece
  Also, why cannot use the phone to re-enter the data. Why do you have this feature disabled? The phone application is just too ridiculously dysfunctional as the player. What you all thinkng? Please fix it!

  AJ777, I'm sorry!

  Please do a factory reset on the player. Follow the steps below:

  1. Press button on the remote control Sony.

  2. Select Setup on the home menu using the left and right arrows.

  3. Select the reset icon with top or down arrow key, and then press ENTER.

  4. select Reset to Factory Default Settings.

  5. follow the on-screen instructions.

  After the reset, try to connect to Netflix and see if the player remembers your username.

  If my post answered your question, please mark it as "accept as a Solution.

• iTunes 12.5.1.21 (September 2016) always forgets settings

  Since the installation of iTunes 12.5.1.21 I agree license and give/refuse Apple permission to share the details of my library every time I start up iTunes.  He forget also all my settings as Shuffle/Albums.

  I am running Windows 7, perfectly up-to-date.

  I tried various suggestions on the web, for example deleting

  iTunesPrefs.xml C:\Users\ < MyAccount > \AppData\Roaming\Apple Computer\iTunes

  but no luck.

  How can I solve this irritating problem, please?

  Thank you

  What anti-virus package do you use? If we exclude C:\Users\ < user > computer time \AppData\Roaming\Apple real scans can help with this question. You can also try to use the right click > run as Administrator option on the iTunes shortcut or open iTunes once in his own safe mode which you reach by pressing ctrl + shift as you start iTunes and do not release until you see a command prompt.

  TT2

• I NEED HELP Please im having a problem to forget my password and when I plug it it says its locked with a password he try to put the itunes thing but

  NEED HELP Please im having a problem to forget my password and when I plug it it says its locked with a password he tried to put the itunes thing but it says enter password I put in what I rember, then said lokced for five minutes help me pls

  Without knowing the password for your iPhone, there is no way to unlock it, bring even you to the Genius Bar. If you continue to enter the wrong password, you will be locked out of your iPhone, and your data will be unaccessable.

• "What is the difference between"Delete"&amp;"Forget this site"when to remove a single item in the 'history' as a 'customization' procedure?" c "

  I am still using Firefox on Windows XP

  Using "Forget this Site" will delete all data stored in Firefox in this area as bookmarks, cookies, words of past, cache, history, and exceptions, so be careful and if you have a password or other data from that domain you don't want to lose then check that back up these data or make a comment.

  You can't recover from this "forget" unless you have a backup of the files involved.

  It has no lasting effect, so if come back you on such a 'forgotten' site, then the data of this Web site will be saved once more.

• El Capitan forget password WiFi

  I own a MacBook Pro 13 "retina early 2015 3.1 GHz i7 16 GB RAM running El Capitan 10.11.5 (currently the latest version).

  The problem is that whenever I re - attach a known WiFi system forgets the password and asks me to re - enter manually.

  Here is a more intriguing symptom: the issue is not with * every * known network. Just with those that I joined after initially, I transferred my data on this laptop from my Mac earlier, a MacBook Air mid-2012 Mavericks running. Those that were already stored on my previous mac work seamlessly.

  "Networks do not forget that this computer has joined" are checked, and I can verify that the new networks are indeed remembered. Passwords are not well.

  I tried a few non-destructive solutions, I found on these forums of discussion, such as checking the permissions of various files/Liberti/Preferences/SystemConfiguration .plist (all are root.wheel 644 and last modified dates of some files are right now, so I know that the system can write to these files) and delete and reset some of the stored WiFi networks. But no solution has worked so far. I'm not ready to delete the completely SystemConfiguration folder and the system of re - create from scratch, because my "WiFi" database now includes more than 100 WiFis that I use from time to time, so I don't want to go to the hassle of re - initialize them all again. I am willing to reset the PRAM or re-install the operating system.

  I've read dozens of similar complaints, but none match my specific situation. I suspect a file that somewhere may have incorrect permissions, with these permissions are poorly defined by the migration program, but it's just a theory.

  Finally, I used so far each MacOSX version and El Capitan is the first one who behaves in this way.

  By/Liberti/Preferences/SystemConfiguration, I meant/Library/Preferences/SystemConfiguration (automatic correctors, ha!)

• Insert the date and time in a model of Pages 5,6

  When I open one of the default templates provided with 5.6 Pages (for example, a letter), I noticed that the document opens with the current date correctly inserted. Yet when I create my own model and save it as a document template (if in my models or elsewhere) the date stamp is no longer up-to-date. Whenever I have create a new document from the template, it gets stuck on the date that I created the template. This means that I have to click on the date each time and select 'Set today' (it's easy to forget).

  My understanding is that the inserted date stamps have is no longer an option of automatic update in Pages 5.x, so I was surprised to see their update automatically in the default templates provided with Pages. How Apple did this, and how do I get the same effect in my own registered designs?

  Pages v5.6.2 and OS X 10.11.5.

  I do not believe that something has changed with the way that Pages manages the dates that we insert into documents, or our new custom templates. The date will not automatically update for me when I create a new custom with a date of month template or a new document with a stamp of date/time in it. In both cases, wait 15 minutes, when I open it or the other, the date of the month in the model does not change and or don't have time in my document on my desktop.

  It stays with v5.6.2 Pages, if you want a date automatically update a model, or in a document current/Sour, you need to use a single table cell, without borders, which is the date of formatting, and has a single equation: = now.

  What I can not explain, for example, is the model of research paper that uses a date inserted regular field current date will appear automatically when opened for the first time in a new document. There are no tables in this model. There is no new parameters in v5.6.2 of Pages that can explain this behavior. This does not work for the user created templates. Pages could have been programmed to update only the date in the models grouped fields, but not user models - and if that were true, then it conforms to the demi-cuite nature in all of this application.

• Phone cannot download and update applications using data or connect via wifi

  A few days ago, I noticed that whenever I have download applications, it is not download immediately and takes maybe a whole for download day actually. I thought it was because I have too many photos/apps on my phone, so I deleted about 10 g of memory, and it still doesn't work.

  I also tried updating my long list of applications that have not been updated, but also does not work (it is set to automatic update)

  I have just updated my software to 9.3.1 but could not do so through my phone directly because it could not verify the updates. I've updated through my iTunes successfully but noticed even after I can't download/update all apps, and when I go into settings and verify software updates, I get an error message that says it can't check the updates.

  Now I can't even connect to my wifi, but my laptop has no problem to do. I have reset the settings network, factory settings and all the people at the Apple Support suggested but nothing works.

  I read somewhere to match iTunes of new conditions and have also made with nothing doesn't.

  Someone at - it other solutions I could try?

  Please do the following and after each test to see if the problem is resolved - if yes, then you can omit the following steps - I tried to list them in ascending order of the effort at least on a Mac and / or an iDevice

  1. Check if the problem is related to a single device and if other devices connect normally-
  2. If the answer 1 is 'yes' - try to connect the device assigned to somewhere else if possible - coffee or the University
  3. Please see recommended settings of WiFi routers and Apple access points
  4. Perform a forced - restart cela do not delete or purge all data and allows to solve many problems - here is how - press and hold the Off / On Home button and at the same time for about 15-20 seconds, until the Apple logo appears. Allow normal startup upward.
  5. Settings - WiFi - < network name > - Click on forget network - do a restart forced 4 and then again add the network
  6. If home - reboot the router by unplugging it for 60 seconds (power) and the plug and reconnect - obviously, this step can be done in a public place like a cafe or airport or University. While you're there - make sure your router is working on the latest firmware (check manufacturer's website)
  7. Settings - general - reset - Reset network settings - remember to have very practical WiFi passwords because it erases the WiFi passwords
  8. If it is a new specific net device in your home - make sure that the router gives enough DNS for all numbers which must / wants a connection - stuff like the printer, Chromecast get overlooked - ask for more details on this so not sure option
  9. Backup the device to iTunes - restore as NEW (no backup) using iTunes - see if solves problem - if yes - restore backup
  10. An appointment of 'Genius' to an Apple Store, or select another authorized service provider.

• I clicked "forget this site", I can cancel it by running the "System Restore" function to retrieve my story?

  I clicked "forget this site" and I am looking for a way to undo it. I have heard say there is no way to retrieve the history of a particular site, once it has been deleted, but surely, it leaves some kind of record in the system? I read an article that suggested running the "System Restore" feature which gives me the option to "restore my computer to an earlier time" before that some changes have been made. Would this work?

  Hello, windows system restore will not restore the file that contains the history of firefox unfortunately (it's called places.sqlite). you would need a backup of your firefox profile folder to retrieve such data.

  Please also update firefox - the version that you are currently using is outdated and affected by many security vulnerabilities.

  Update to the latest version of Firefox

• How long until what Firefox forget your previous session?

  I know that Firefox can restore automatically my previous session if my computer falls down or is turned off at the plug, but is there a as a threshold for that, so to speak? If I let my computer off for long enough he'll forget my session? Or it will automatically load to the top yet?

  Yes, if the sessionstore file is there, Firefox will use it. If it isn't, he used. If you reinstall windows and it deletes your data personal, the file will not be there, while Firefox will restore your session

• Migrating data with external box HD

  Ok.

  I'm a novice here... I had a Unibody MB (2008) running Yosemite and the screen is out. I bought a new MB Air and it is running El Capitan. The Apple local store in the city told me that I had to get an external HD case, insert the old Mac to the MB Air HD through the USB port and use the Migration Wizard. My old HD is much greater than new and Migration Assistant is stuck on the screen that says "what you want to transfer?"  and is hung "estimate disk space..." Under the "documents and data", there is an "Edit" button and if clicked it brings up the username from the old HD. There is an error message that says 'this attention to user needs before migrating', but don't tell me what to do.

  If this can be as simple as open 2 windows in the finder and drag and drop between the two discs?

  What all the old mail? How should I treat that?

  You don't want to drag - move unless nothing else works. If you have already launched the MacBook Air and created an account on it, run the disk with the mounted external hard drive utility. Select the disk utility and repair the drive. I have not seen this error, but my first thought is that the reader can have a few directory damage and with lucky Utiity disc will fix it and you can try the migration again.

  Assuming that the Migration is possible, the Migration Wizard will create a new directory of the user and put all that existed on the old computer. This includes all mail that have been saved on your disk. Do not forget that modern mail servers keep mail on their server rather than on your computer unless you move it there. Regardless of the outcome of your attempt to migration, come back and let us know how it went.

• can reverse you him 'forget a site"If you accidentally tap?

  Hi I was looking in the history for something and wanted to delete which I did--accidentally highlighting the site below (facebook) that I didn't "forget" to firefox on can I change this? or anything else I discovered Facebook go forget all in the history if I wanted to go back to something?

  With the help of "Forget this Site" will delete everything as bookmarks, cookies, passwords, cache, history, and exceptions in this area, so be careful and if you have a password or other data from that domain that you do not want to lose so take note of these passwords and bookmarks.
  
  You can't recover from which "forget" unless you have a backup of the affected files.
  
  It has no lasting effect, so if come back you on such a 'forgotten' site, then the data of this Web site will be saved once more.

  You can use this extension to remove entries from the menu.

  • Menu editor: https://addons.mozilla.org/firefox/addon/menu-editor/

• 14 Firefox forgets where to save downloads

  Firefox version: 14.0.1
  O/s: Windows XP Edition family version 5.1.2600 Service Pack 3 Build 2600

  When I try to record a series of image files on the same site in a destination directory using a right click > Save Image under..., frequently (but at random intervals) Firefox forgets where the record of the previous file.
  I can correctly save multiple files in the expected folder, then find that the Save As dialog box has forgotten the target folder. Sometimes, it restores the default download folder, but sometimes, it comes in a folder that I used for downloads (on a different Web site) days. It can then return to a different folder, I also used for downloads (from a third party site), also days ago.
  Occasionally, I navigate to the folder target for each of a succession of downloaded files, then Firefox starts to remember where files go - don't forget again, later in the series. This means that I have to pay attention to what makes Firefox and wasting time check which folder he thinks is the target, rather than to focus on the task, I'm in show.
  I don't remember meeting this stupid behavior and worse in previous versions of Firefox. So far, I noticed only when you use the right click > Save Image under... but cannot download some he did not appear with other methods.

  The current versions of Firefox don't forget not the directory download, based on the URL, so if the URL changes then the default folder can be selected if he has not selected a folder for this server before download.
  
  You can disable this feature to not forget the download via the prefs directory Boolean browser.download.lastDir.savePerSite on the topic: config page.
  
  The pref browser.download.lastDir.savePerSite does not exist by default (it's a hidden pref), you will need to create it.

  Create a new pref Boolean with the name browser.download.lastDir.savePerSite and set it to false.

  • http://KB.mozillazine.org/about:config

  You may need to clear the "Site preferences" via clear recent history to delete already stored data.

• forget this site

  In the newspaper that I clicked "forget about this site" - how to manage the list of these sites?

  "Forget this Site" deletes all the current content (bookmarks, passwords, cookies, cache, history, exceptions) you have saved from a Web site.
  
  It has no lasting effect, so if come back you on such a 'forgotten' site, then the data of this Web site will be saved once more.
  
  You can not recover the forgotten data unless you have a backup of files in the Firefox profile folder.

  • http://KB.mozillazine.org/Profile_folder_-_Firefox