Access control for Client VPN on Cisco 5520

Similar Questions

• Different 'outside_cryptomap access-list"for each VPN?

  Hello

  Just for my understanding.

  I have a VPN connected to my Cisco ASA 5520 when I tried to add an another VPN, the I must create a 2nd cryptomap, can I not create a group so there is only one card encryption?

  Currently I have:

  access-list 1 permit line outside_cryptomap_1 extended ip 0.0.0.0 0.0.0.0 172.19.15.0 255.255.255.0

  I just added outside_cryptomap_2 line access-list 1 permit extended ip 0.0.0.0 0.0.0.0 172.19.2.0 255.255.255.0

  But I was wondering if I could use something like:

  access-list 1 permit line outside_mycryptomap extended ip 0.0.0.0 0.0.0.0 VPN_Remote_Networks object-group

  When I do this, but I guess that this will cause a problem with the address in hand?

  You must use different access-list in cryptomap for each VPN.

• Access control for iSCSI

  Hi all

  I have two EqualLogic PS6500E. On volumes of, created under the access control list , I applied and restriction of IP address to allow only the beach of 192.168.1. *.

  Since a few days under connections , I noticed traffic/connections from other IP addresses (not high-end 192.168.1. *) actually configured on the servers of access to this volume.

  Any ideas how is this possible?

  Thanks in advance

  Sébastien

  Sorry, I wanted to add.  Run the Remote Setup Wizard and select the option "Configure MPIO".  That will list all subnets available on this server.  Exclude everything except the iSCSI subnet.

  Kind regards

• Client VPN und Cisco asa 5505 tunnel work but no traffic

  Hi all

  I am new to this forum and Don t have a lot of experience with Cisco, so I hope I can get help from specialists.

  I have the following problem:

  I installed und konfigured ASA 5505 for use with vpn client. I would like to access the local network from outside through vpn.

  To test, I installed ASA 5505 with ADSL (pppoe) and tried to give access to the internal network.

  Of course whenever I have recive the supplier's different IP address, but it didn't is not a problem reconfigure in the vpn client.

  After the connection is established (vpn tunnel work) I can see my external network packets. But I Don t have any connection to the internal network.

  I erased my setup yesterday and tried to reconfigure ASA again. I didn t tested yesterday, because it was too late. And I know that I Don t have the authorization rule at present by the ACL. But I think I'm having the same problem again. (tunnel but no traffic).

  What I did wrong. Could someone let me know what I have to do today.

  With hope for your help Dimitri.

  ASA configuration after reset and basic configuration: works to the Internet from within the course.

  : Saved

  : Written by enable_15 to the CEDT 20:29:18.909 Sunday, August 29, 2010

  !

  ASA Version 8.2 (2)

  !

  ciscoasa hostname

  activate 2KFQnbNIdI.2KYOU encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  PPPoE client vpdn group home

  IP address pppoe setroute

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  boot system Disk0: / asa822 - k8.bin

  passive FTP mode

  clock timezone THATS 1

  clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  Server name 194.25.0.60

  Server name 194.25.0.68

  DM_INLINE_TCP_1 tcp service object-group

  port-object eq www

  EQ object of the https port

  inside_access_in list extended access permitted udp 192.168.1.0 255.255.255.0 no matter what eq field open a debug session

  inside_access_in list extended access permitted tcp 192.168.1.0 255.255.255.0 any object-group DM_INLINE_TCP_1 open a debug session

  inside_access_in list extended access deny ip any any debug log

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.0.0 255.255.0.0

  permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.10.0 255.255.255.128

  homegroup_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Outside 1500 MTU

  Within 1500 MTU

  IP local pool homepool 192.168.10.1 - 192.168.10.100 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm-625 - 53.bin

  ASDM location 192.168.0.0 255.255.0.0 inside

  ASDM location 192.168.10.0 255.255.255.0 inside

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  inside_access_in access to the interface inside group

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN group home request dialout pppoe

  VPDN group House localname 04152886790

  VPDN group House ppp authentication PAP

  VPDN username 04152886790 password 1

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  TFTP server 192.168.1.5 inside c:/tftp-root

  WebVPN

  Group Policy inner residential group

  attributes of the strategy of group home group

  value of 192.168.1.1 DNS server

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list homegroup_splitTunnelAcl

  username user01 encrypted password privilege 0 v5P40l1UGvtJa7Nn

  user01 username attributes

  VPN-strategy group home group

  tunnel-group home group type remote access

  attributes global-tunnel-group home group

  address homepool pool

  Group Policy - by default-homegroup

  tunnel-group group residential ipsec-attributes

  pre-shared-key ciscotest

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:930e6cddf25838e47ef9633dc2f07acb

  : end

  Hello

  Normally, you want a static public IP address on the ASA to allow it to receive connections from VPN clients (avoid to change the IP address all the time).

  If you connect via VPN, check the following:

  1. the tunnel is established:

  HS cry isa his

  Must say QM_IDLE or MM_ACTIVE

  2 traffic is flowing (encrypted/decrypted):

  HS cry ips its

  3. Enter the command:

  management-access inside

  And check if you can PING the inside ASA VPN client IP.

  4. check that the default gateway for the LAN internal ASA within intellectual property (or there is a road to the ASA to send traffic to the VPN clients).

  Federico.

• VPN on Cisco 5520

  Hello

  What are the possibilities that exist for a site to site vpn running in our environment with the following facilities

  Cisco ASA 5520 - running on a multiple context mode

  Cisco 3750 switches

  Microsoft TMG

  In my view, these options are limited in terms of VPN endpoint mode.

  Is there a VPN module we can buy for 5520 run IPSEC VPN?

  ASAs all on Board have a VPN, so there is nothing you have to buy. But you need at least version 9.0 software where the VPN site - to have been introduced to several way of context:

  http://www.Cisco.com/en/us/docs/security/ASA/asa90/release/notes/asarn90.html#wp586890

  VPN remote access are still not supported in multiple context.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• ACL for Client VPN number

  Hello

  I'll set up a ASA 5550 as a VPN concentrator, so that clients connect to my Web inside the ASA server. all things appear functioned properly (the customer can access the server), the problem I have is when I configure an ACL to allow only port 80 (http/www) and deny all other traffic, I note that the ACL does not work, I mean I still have full access to the server from the client.

  This is the config I've done:

  inside_access_out list extended access permitted tcp 10.20.0.0 255.255.255.0 192.168.200.100 eq www

  inside_access_out deny ip extended access list a whole

  Access-group interface inside inside_access_out

  I also tried to do the following, but I noticed the same problem:

  access-list extended inside_access_in permit tcp host 192.168.200.100 eq www 10.20.0.0 255.255.255.0

  inside_access_in deny ip extended access list a whole

  inside_access_in access to the interface inside group

  Could someone help me solve this problem?

  Best regards /.

  Ismail

  Where is the map encryption applied? Are you trying to filter incoming or outgoing traffic?

  By default, when the following command is enabled:

  Sysopt connection permit VPN

  VPN traffic will bypass the rules configured on the interface of the encryption card applied to.

  I suggest to use VPN-filters:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808c9a87.shtml

• Windows 7 x 64 support for Client VPN with SBL/PLAP

  Is it now or will it be a customer VPN Windows 7 x 64 support prior to logon Access Provider (PLAP) that replaces start them before logon (SBL)?  I understand that connect any client supports it, but the customer needs customer VPN (IPSec) rather than any connection (SSL) because of their current license on the SAA.  They have little license for SSL.

  It is possible with AnyConnect, however, there is currently no functionality SBL/PLAP for the traditional IPSec VPN on Windows 7 client. There is an improvement for this feature request, but it has not been applied and so I can't give you an idea on whether she will ever be supported, see CSCse47544.

  -heather

• How can I disable the user access control, for an update of a Web site?

  This is the site of poker for the best day of Milwaukee.

  Hello

  Access search by: click on Windows Orb/Start key > click on the text box and type "User Account Control" to get the shortcut to user accounts. You can disable UAC.

  However, the word of advice, be warned that disable UAC will allow any application and good or bad that gain access to the computer can cause damage to him.

  Don't forget that the site you access is safe and secure and if did the update, try to return to turn on UAC

• Shared Services Assign Access Control for Essbase

  Hi we have an opportunity which has its commissioning as filters in the essbase group. I tried assigning its filter to thim thanks to assign a control access to shared services. I am able to see the user as well as the filter that I created for the user, but when I try to assign them to him and save is really not get assigned. He rest of stays the user doesnot have filters assigned to his account. Have I missed something.

  Thank you.

  Did you try maxl:

  grant appname.dbname.filtername user filter;

  See you soon

  John

  http://John-Goodwin.blogspot.com/

• VDI with ISE access control

  Hi guys,.

  Can ISE access control for VDI users with thinclients like PC? Now, we want to implement authentication 802. 1 x for the VDI users, but I don't know if this can be done by ISE. We just need to configure access switch ports to open 802. 1 x as usual and the switch will then relay the RADIUS to the ISE?

  Hello

  The link below can help you:-

  http://blogs.Cisco.com/borderless/using-TrustSec-to-simplify-virtual-desktop-infrastructure-VDI-deployment/

• Report of access control

  Hi all

  I need to generate a report of access control for a planning application. Instead of getting the report, HspReportingServelet have generated. The administrators guide shows that we need to define report parameters.

  Where we should define report parameters in order to generate the report from access control?

  You have the Adobe reader installed on your machine?

  Concerning

  Celvin

• Problems with "security access control list '.

  Hello
  
  My system is configured as follows
  UCM - 11 GR 1 material - 11.1.1.4.0 (Build: 7.3.0.180)
  -Database 11 GR 2
  OracleTextSearch - engine is used
  RoleEntityACL - component is enabled
  -Parts of my config.cfg

  SearchIndexerEngineName=OracleTextSearch
  IndexerDatabaseProviderName=SystemDatabase
  UseEntitySecurity=true

  I want to create lists of access control for users, groups, and roles. I followed the the next page http://download.oracle.com/docs/cd/E17904_01/ documentatoindoc.1111/e10792/c03_security.htm#CDDBCIDA
  Everything seems to work fine at first, because I'm able to add users, groups, and roles to the ACL of the document. The problem is that adding a user, group or role of the ACL of a document does not affect the rights of a user a of the document.
  
  Example:
  -Wear a read access to "public"-SecurityGroup
  -UserB is to check in a "document1" to the SecurityGroup 'public' and adds UserA to the ACL of "document1" give UserA 'read' and 'write' access to "document1".
  -The result is that UserA doesn't have to 'write' access to "document1", well it is in the ACL (same problem with groups and roles)
  
  In this scenario shouldn't UserA have "write" access "document1" or I have a bad understanding of access control lists?
  
  Thanks in advance
  Brahim

  You heard wrong...

  Permissions through ACL are subject to the same rules of intersection between the permissions granted by the intermediary of roles or accounts.

  If you want write access to a document, you must have at least write access to the security group of the document, account and have RW permissions in the ACL.

  In other words work ACL on top existing accounts/groups and roles that they do not replace the existing UCM permissions. You can restrict the permissions by an ACL but not grant permissions that the user has not already set for the account or the security group.

  And by are the ACL way ugly generally impassable and unmanageable so if you have to use them all to be very careful!

  hope tha helps
  Tim

• Evaluation version for the cisco secure access control server

  Hello

  I can get the trial version for the cisco secure access control server. IF SO pls send me the link.

  Thank you

  Hi Thomas,

  You can download ACS for windows 4.1 or 4.2 from the link below:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/ACS-win-eval

  For ACS 5.x, please visit cisco.com

  Download software > Security > Cisco Secure Access Control System 5.x > Secure Access Control System Software

  HTH

  Kind regards

  Jousset

  Please evaluate the useful messages-

• Client VPN CISCO ASA for Android

  Hi guys

  I just received a request from a client who said he expects the procedure to establish a VPN from an Android device, as far as I know there is a soft ANYCONNECT but in my case, the client uses a CISCO VPN CLIENT, in this case it is possible to configure a VPN connection on the device, or I should use ANYCONNECT?

  Kind regards.

  Connection via the android client will be like the legacy cisco VPN client connection. You need only anyconnect mobile licenses if you connect with the android anyconnect client.  Using the android client built in will consume licenses peer IPSEC. If no additional license not required.

• iPad VPN from Cisco ASA 5520

  Hello

  I'm trying to get my ipad to VPN to our Cisco ASA5520.

  I think I have all the correct settings on both ends (I am able to vpn to the asa using a cisco 871 as the remote client).

  I think that for some reason the client vpn on ipad is not even make the asa. My question is: How can I monitor the ASA logs to see if the same connection attempt and eventually find the failure?

  Thank you

  M

  try: -.

  Debug crypto ISAKMP

  Debug crypto ipsec

  Vpn-sessiondb SH remote control (to see if the client is connected)

  I have configured ipad for remote vpn client, the user could connect to the 5520 but why that I had to use the ip addresses to access, but I couldn't use internal dns names. try to understand that at this moment.

  It may be useful

  Manish