ACS 3.2 SNMP
Dear friends,
My discussion on how to add an ip address of the snmp server and the community in the apparatus of the ACS 3.2.
I can tell that you cannot configure SNMP on a device to version 3.x. I have access to 4.x and 3.x devices. In the v4.x appliance SNMP configuration is under System Configuration > Configuration of the device, but there is no SNMP configuration in the same area on the device v3.x.
Tags: Cisco Security
Similar Questions
-
Cisco Secure ACS 5.3 SNMP agent does not
Hello
I have problems with the SNMP on Cisco Secure ACS 5.3 agent (patch level 5) stop, is there a quick way to restart the SNMP daemon via the command line?
Robert,
I understand where you come, I encountered the following bug:
The process of the SNMP agent in demon device ACS stops.
and reboot the box will bring him back to the top and after about 3 days, he'd stop. I just want to see if it's the same bug that could be back in patch 5. The best thing to do at this stage is to plan a quick down and restart the box to see if the snmp process starts again. If this then gives IT a week to see if the snmp Protocol falls down. If it does then make reference to this bug and open a new case of tac for repair. If not, then you should be in the clear.
Thank you
Tarik Admani
-
Adding accounts on ACS using SNMP
Hi people,
I use ACS 4.2 and I was just wondering if it is possible to add user accounts by using snmpset? If so, anyone found any documentation on what needs to be done? I have the SNMP running on it and check with the ACS using snmpget.
Thank you, S.
Hi Shane,
It is unfortunately not possible. You cannot add users via SNMP.
However, you can add multiple users at once using RDBMS synchronization.HTH
Amjad
Sent by Cisco Support technique iPad App
-
2611XM Terminal Server + ACS + new authentication when selecting menu options
Hello
I managed to configure ACS authentication on my 2611xm router,
After you connect to the router, I have an autocommand configuration to run a menu.
My problem is when you select the option in the menu,
You are then re invited to reauthenicated against the router before connecting to the line,
can someone tell me how to prevent it.
Thank you for your time and effort in advance, I have attached a config below.
DDRAS01 #sh running-config
Building configuration...
Current configuration: 6854 bytes
!
! Last modification of the configuration at 10:28:49 GMT Sunday, February 21, 2010 by
! NVRAM config update at 19:25:53 GMT Saturday, February 20, 2010 by
!
version 12.4
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
Service linenumber
sequence numbers service
!
hostname DDRAS01
!
boot-start-marker
boot-end-marker
!
Security of authentication failure rate 3 log
Passwords security min-length 6
logging buffered 51200 informational
record of the rate-limit all 10000
recording console critical
enable password 7
!
AAA new-model
!
!
AAA authentication login default group Ganymede + local
AAA authentication login if_needed local
the AAA authentication enable default
AAA of authentication ppp default local
AAA authorization exec default group Ganymede + local authenticated by FIS
AAA accounting exec default start-stop Ganymede group.
orders accounting AAA 15 by default start-stop Ganymede group.
!
AAA - the id of the joint session
clock timezone WAS 10
summer time clock WAS recurring last Sun Oct 02:00 last Sun Mar 03:00
no location network-clock-participate 1
No network-clock-participate wic 0
IP cef
!
!
!
!
list of IP domains
list of IP domains
IP domain name
the IP 2033 172.16.1.1 host dd-cr-01F
ddsws01 host IP 172.16.1.1 2034
ddsws04 host IP 172.16.1.1 2035
ddce565 host IP 172.16.1.1 2040
IP-name server
IP-name server
!
!
!
password username d ' operators 15 7 privilege
!
!
property intellectual ssh source interface FastEthernet0/0
property intellectual ssh event logging
property intellectual ssh version 2
!
!
interface Loopback0
IP 172.16.1.1 255.255.255.255
!
interface FastEthernet0/0
IP
255.255.255.0 Speed 100
full-duplex
!
interface Serial0/0
no ip address
Shutdown
!
interface BRI0/0
no ip address
encapsulation hdlc
Shutdown
!
interface FastEthernet0/1
no ip address
Shutdown
automatic duplex
automatic speed
!
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0
!
IP http server
no ip http secure server
Ganymede IP source interface FastEthernet0/0
!
radius of the IP source interface FastEthernet0/0
exploitation forest installation local6
logging
SNMP-server
RO community SNMP-server
RW community SNMP server location
contact Server SNMP d ' operators
!
title of menu ddras01 ^ C
Server Terminal Server for Cisco
Select number from the list below
Use "ctrl + shift + 6" then 'x' to switch to the menu
^ C
text of ddras01 to menu 1 connect to the DD-CR-01
order of menu 1 ddras01 resume JJ-cr-01 / dd-cr-01 2033 telnet connection
ddras01 text menu 2 connect to DDSWS01
order of menu 2 ddras01 resume ddsws01 / ddsws01 2034 telnet connection
text menu 3 ddras01 connect to DDSWS04
order of menu 3 ddras01 resume ddsws04 / ddsws04 2035 telnet connection
text menu 8 ddras01 connect to DDCE565
order of menu 8 ddras01 resume ddce565 / ddce565 2040 telnet connection
menu 9 ddras01 text output
menu ddras01 command menu-exit 9
ddras01 menu clear-screen
menu ddras01-status line
menu-ddras01 line mode
radius-server host 10.2.0.50
RADIUS-server application made
radius-server key 7
!
control plan
!
privilege exec 15 level write terminal
writing level 15 privileges exec
Ping privileges exec level 1
privilege exec 10 undebug ip icmp level
privilege exec 10 undebug ip level
level of privilege exec 10 undebug all
privilege exec 10 undebug level
terminal monitor exec level 10 privileges
privilege exec 10 level terminals
privilege exec 15 level show running-config
See configuration at the privileged exec level 5
show privileges exec level 5
privilege exec 10 debug ip icmp level
privilege exec level 10 debug ip
privilege exec 10 level debug all
debugging privileges exec level 10
clear interface of privileges exec level 10
clear counters at level 10 privilege exec
level of privilege exec 10 clear
!
Line con 0
password 7
Synchronous recording
line 33 64
No exec-banner
exec-timeout 0 0
no activation-character
No exec
preferred transport telnet
transport of entry all
character of exhaust-27
StopBits 1
FlowControl hardware
line to 0
line vty 0 4
password 7
Synchronous recording
ddras01 menu autocommand
line vty 5 181
password 7
Synchronous recording
ddras01 menu autocommand
!
NTP-period clock 17208487
source NTP FastEthernet0/0
NTP server
end
Hello
You have aaa login default configured for authentication, with this you get invited
When you try to access the line.
Under line VTY 5 181 try adding:
authentication of the connection /NOAUTH
exec authorization /NOAUTH
Add the lines of aaa:
/NOAUTH AAA authentication login no
/NOAUTH AAA authorization exec no
This should stop the authentication to the lines.
-Jesse
-
Hello
Currently using Windows ACS 4.0 and 1113 Ver4.2 with SNMP patch to allow ping.
We want control services using Solarwinds APM, you fix the template above, you can see details of SNMP from the ect server and Services. But it seems to require a user name and password to monitor services, which is not a Windows user name and password. I tried to add Administrators user name and the password of the ACS, but does not control the services.
Is there a certain procedure to monitor the Services of the CSA with a 3rd party like Solarwinds product?
Concerning
Craig
The ACS SE 1113 is a server, locked in order to describe how the services are done with a third-party utility, it would very probably install some type of agent to look/monitor/or even send traps SNMP for the ACS Services (that are installed on the operating system).
ACS already does in itself, if you go to the System Configuration > ACS Service Management > you could configure ACS to contact you in the event of a service failure. You may also send the report of these alerts to a Syslog server: System Configuration > Logging > change the case report.
Just realized that there is also an SNMP Agent (System Configuration-> Configuration of the device--> SNMP Agent), this could provide some additional information:
Keep in mind:
Documentation of the ACS CSCsj18497 device doesn't not list SNMP MIB support
Hope this helps,
-
Experts of the Association,
Need quick answers to issues related to GBA 5.1 for a customer. I haven't used the ACS5.1 still so watch out for the easy questions
(1) is it possible to generate the report for users who are inactive for 30 days? Customer looking for these users to see if they really need access to any checking device.
(2) are there any known issues affecting the level of priviligaes users. In the current implementation of that client users are always connected in 1 even private if they are affecting the 5 private level. I understand with ACS 4.x, we can activate the exec process and assign priv under user/group policy. What are the configurations that the client might be missing in this case possiby?
(3) are there any SNMP or other available in 5.1 ACS notice where admin can be notified at the time where a set of particulat user connects.
Thank you
Hello
Please find answers inline:
(1) is it possible to generate the report for users who are inactive for 30 days? Customer looking for these users to see if they really need access to any checking device.
[YEARS] You can generate reports of user using several elements, including reports for the last 30 days:
(2) are there any known issues affecting the level of priviligaes users. In the current implementation of that client users are always connected in 1 even private if they are affecting the 5 private level. I understand with ACS 4.x, we can activate the exec process and assign priv under user/group policy. What are the configurations that the client might be missing in this case possiby?
[YEARS] You can do exactly the same implementation GBA 5.x. just create permission authenticate profiles to apply to users with success.
(3) are there any SNMP or other available in 5.1 ACS notice where admin can be notified at the time where a set of particulat user connects.
[YEARS] You can create "Alarms" which will send an e-mail notification or a syslog server:
Monitoring and reports > ... > Alarms > Thresholds > Add HTH,
Tiago--
If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.
-
ACS 5.1 mab reauthentication in every 1 minutes
Hello
I use Cisco ACS 5.1. I want to authenticate my phones ip with mab (phones Avaya) and the commputers with dot1x.
Everything works fine except that the phones that are authenticated successfully with mab attempts to authenticate again
and again and again... and this fills the newspapers of GBA. Each authentication is successful and the phone don't hang up. But it fills
until my logs and makes them useless.
change the version: cat4500-ipbasek9 - mz.122 - 53.SG3.bin
port config:
interface FastEthernet2/25
switchport access vlan 107
switchport mode access
switchport voice vlan 502
switchport port-security maximum 3
switchport port-security
aging of the switchport port security 1
inactivity of aging switchport port-security type
no event log status link
load-interval 60
Speed 100
full duplex
QoS based on vlan
authentication event failure action allow vlan 109
action of death event authentication server allow vlan 101
living action of the server reset the authentication event
multi-domain of host-mode authentication
open authentication
authentication order dot1x mab
authentication priority dot1x mab
Auto control of the port of authentication
restrict the authentication violation
MAB
no link-status of snmp trap
dot1x EAP authenticator
dot1x quiet-time 30
dot1x timeout server-timeout 25
dot1x tx-deadline 15
dot1x timeout supp-timeout 25
dot1x max - req 3
TX-queue 3
high priority
No cdp enable
spanning tree portfast
IP dhcp snooping limit 10 speed
endThank you
Andras
Hello
If you delete the commands:
switchport port-security maximum 3
switchport port-security
aging of the switchport port security 1
inactivity of aging switchport port-security typePhones stops at authenticate every minute?
Please note that you set the time of aging at 1 minute, which means that if the phone doesn't send any traffic, the switch will remove its mac address FRO mthe mac table, therefore, the dot1x process will kick.
HTH,
Tiago
--
If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.
-
Assignment of VLAN dynamic RADIUS ACS 5.2 Server with NAC
We are trying to reduce the number of ssid in our network wireless with assignment of vlan dynamic with the acs. Our problem is that we use Cisco NAC so with assignments of vlan dynamic user will be checked by the NAC. Agent of Cisco sometimes pop up and do nothing to do or give a message cannot locate server. We even got an OOB error. Someone used a VLAN dynamics with the acs and the NAC successfully? The NAC is Out of Band
Hello
I supported oob nac and wireless and your efforts to make the dynamic assignment of VLANs will not work because of the way in which him vlan quarantine and access are mapped to this ssid.
This work in in-band mode, however your design. This WLAN key needs to exist because the Manager sends the snmp trap to move the client from quarantine access.
Just as a note, I'm sure you are aware is that ISE is the evolution of the acs and the NAC. Basically this your solution to reduce the skates and posturing of the customers.
Sent by Cisco Support technique iPad App
-
Does anyone know where I could find information (MIB) machine for Toshiba MFP devices file. I googled had and checked the predominant sites for these types of files. I'm looking to get the OID for an eStudio-600 so I can configure the SNMP interruptions for alerts of toner and paper jams.
Thank you
Mike
PS: I put here as a matter of SNMP network, if it's wrong please feel free to move it to the right forum.
In my opinion, this forum is wrong place for this question. I think you should contact your local dealer where you bought your eStudio-600.
They offer a type of support or not? -
Is it possible to configure SNMP or logging remotely on the R8000?
The stock firmware allows logging of external data?
As a way secret for the program to install/activate SNMP?
Or direct the output of logging to an external server?
Because the viewport of the newspapers little pointless, just doesn't really cut it and go through the journal by email whenever you want to look over is simply absurd.
There is no support SNMP, for one of the Netgear router machine, in stock firmware.
-
Hi all
I had to reset my ReadyNAS Ultra 6 by default and have lost the SNMP addon. I can't locate on my own PC, or on one of the forums. I searched for hours without success. Anyone out there have the .bin still available and power poster file or email it to me please?
Thanks in advance.
Hello mdshelton123,
Stephen is right, we saw the link you gave, but you already have updated the firmware of the OS6.
I asked the subject to be moved archives available in the community. It's here: https://community.netgear.com/t5/Community-Add-ons/SNMPon-0-1-1/td-p/789452
Kind regards
-
StorCenter px6 - 300 d SNMP SNMP problem after FW update to 4.0.2.9960
Hello
We have a problem in PX6 - 300 d, after the upgrade from version 3.2.3.15290 to 4.0.2.9960, FW SNMP configuration. Ishmael of application allows us to manage matrices. After updating the FW one of storage, the application can no longer collect information. Notify know if there was no change of FW which caused this problem?
SNMP parameters in storage, are equal, the difference in this version of the FW of storage.
Thank you for your help
Adias
Hi adias.
There is a newer version of the firmware. I recommend updating to the latest version to see if the problem persists.
-
Hello
I'm all new to SNMP, although I have used LabVIEW a few times in recent years. Office supplies for the moment, I am developing an application to test the power. We use a G756N Dell PDU for each switching power. I tried a couple of approaches to control and SNMP is the most promising so far. During my research I came across free ManageEngine MibBrowser and I could find the last MIB to download the firmware from Dell here. I was able to communicate with the UDA and points of sale under and out so far, but I really need to integrate control of the PDU in the application of LabVIEW to automate tests. I'm pinned Mark Yedinak and his APC PDU SNMP communication library, only the most recent of which I found examples in this thread.
I tried to do a VI to test communication in LabVIEW using the OID I received from MibBrowser, but it returns an error code 2, noSuchName. The PDU is configured to use SNMP v1 and the public and private communities write access +. I tried with and without the main point, but without success. I'm using LabVIEW 2013 64-bit. Could someone please review the information below and see what I could do wrong, or that the direction to take to solve the problems there?
Thank you
Simon
MIB object IDS:
. iso.org.dod.internet.private.enterprises.dell.pdu.pdusub.hardware.rPDU.rPDUOutlet.rPDUOutletSwitched.rPDUOutletSwitchedControlTable.rPDUOutletSwitchedControlEntry.rPDUOutletSwitchedControlCmd
. 1.3.6.1.4.1.674.10903.200.2.200.130.1.4.1.4.1: {1 or 2}
I added le.1 at the end of the index to the first exit, and 1 variable is instantaneous, while the 2 is instant off
Photo
VI:
Front panel:
Wiring:
Link to examples of SNMP Communications and APC_PDU.zip:
http://forums.NI.com/T5/LabVIEW/APC-ups-with-desktop/m-p/2431528/highlight/true#M749059
For some reason, I can't the real VI set. The MIB is too in the archive. Its in my selection here:
https://DL.dropboxusercontent.com/u/10871313/power%20Supply%20Testing.zip
Thanks again
-
I found an online library of SNMP vi that someone writes and I fight so he can work. I think I use them properly because I can get some OID to work
and others do not return anything.OID.1.3.6.1.2.1.1.1.0 - works fine. It returns the same OID, the data type, then the value.
OID.1.3.6.1.4.1.21796.4.1.3.1.4.1 - does not work, it returns a different OID and nothing to the value or the type of data.Anyone used this library before? All I have to do is get a value from a device. Any ideas?
The original poster has contacted me directly, and I gave an updated version of the library which has solved its problems. To be honest I don't know what the updates are in the latest version of the library from the version he got was old enough. In any case, here's the latest version for someone else who may need SNMP.
-
MSM765 Team: port source MSMS765 team of SNMP
Hi all
We have a team of controllers MSM765. We use the ports of controllers in the following ways:
- Internet port: only for the management
- LAN port: use for production, the traffic of users
Our network management tool (SNMP querys, etc.) is in the network of EHF Internet port of the team. The team sends traps SNMP with LAN Port as a source. We do not want to open any type of comunicarion between the 'Network management' and 'network of Production '.
It is possible to change the source port the SNMP Traps generated by the team of the LAN Port to the Internet port?.
Best regards.
Hello
My problem must be linked with the routing, as my default route points to a gateway in my LAN Port. I can solve it by adding static routes for networks explicits (hosting the SNMP servers) pointing to the gateway on the Internet Port.
Best regards.
Maybe you are looking for
-
Thunderbird is stuck on the start page of mail (Mac, Mavericks)
Thunderbird has been working well on my Mac, but after the last update + restart, it seems to be stuck on the mail start page. Here is a screenshot: http://i.imgur.com/gKFjEaH.png When I click on 'read messages', it is said so "host contacted, the co
-
Firefox works with the mavericks?
In short, I have a MacBook Pro to late 2013 running OS 10.9 Mavericks. Firefox worked until it it didn't. It opens at all, it crashed my computer. I uninstalled it it's firefox a 25 and downloaded the most recent, firefox 26, he also worked for a day
-
Can I convert a Pages, Microsoft Word doc?
Can I convert a Pages, Microsoft Word doc?
-
What wifi router works best with an iMac
Please be nice to me I don't really know what I'm talking about, but really really need help. We have an iMac with wifi connections and currently run a cisco linksys e1000, who is five years old at least, and I'm sure is very tired, either completel
-
S2340M - warranty info / need to manufacture date
S2340M Monitor is pink with horizontal lines. Hard reset did nothing. It fails of SUBMISSION and automatic test CN - 0293M 3-64180 - 36F - 0E5T Wondering if anyone can tell me the date of manufacture to see if it is still under warranty. I swapped th