ACS 4.2 - one local user to be part of several local groups

Similar Questions

• Cisco ACS 4.2 a user in several local groups

  Currently, I like this group map

  ACS groups window

  GRP of GRP-A-B-1 and PDM - 2
  GRP - A. GRP - 1

  GRP - Grp-2 B

  For example currently a user test1 is part of two groups 1 and 2 under windows and is mapped to the Grp-A-B of the CSA. Is it possible if I delete the mapping of Grp-A-B in ACS and can see the user test1 speratley in both groups (Grp - A and Grp - B) to GBA?

  Salam Muhammad,

  If you have a local user in ACS, this user cannot be a member of both groups at the same time.

  The same concept applies to external users. They cannot be mapped to two different groups at the same time.

  If you delete the configuration of Grp-A-B, the test1 user will be mapped to the first group in the list because ACS 4.2 process mapping group in the order:

  ' the snip "'

  Order of group mapping

  ACS always maps users to a single group of TISA. However, a user can belong to several groups the group mapping. For example, a user named John could be a member of the ensemble of the engineering group and California, and at the same time be a member of the combination of Group Engineering and management. If the value of group ACS mappings exist for these two combinations, ACS must determine what group John should be affected.

  ACS prevents contradictory group set mappings by assigning an order of mapping for the whole group maps. When a user who is authenticated by an external user database is assigned to a group of ACS, ACS begins at the top of the list of groups for this database mappings. ACS sequentially checks group memberships of user in the database of the external user against each group mapping in the list. Where to find the first set group mapping corresponding memberships to external users in the user database, ACS assigns the user to the group this group map ACS and ends the process of mapping.

  ' the snip "'

  Reference:http://goo.gl/cvc474

  HTH

  Amjad

  Rating of useful answers is more useful to say "thank you".

• Why remove the Terminal Server on Windows Server 2008 Standard Server HKEY_USERS\S -? When one connects users off?

  Why remove the Terminal Server on Windows Server 2008 Standard Server HKEY_USERS\S -? When one connects users off?

  I have a setting wrong?
  I can't find a setting that relates to this in either Terminal Server Config or Terminal Server Manager...
  Any help would be much appreciated.

  Hi Richard,

  Thanks for posting your question on Microsoft Community!

  I suggest you to ask your question in the section service Terminal Server TechNet forums for assistance.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  I hope this helps.

• user belongs to a domain and user does not belong to the local administrator or power users groups, or any custom group and the user is not part of the domain administrators group, but user show that it is admin

  WinXP
  user belongs to a domain and user does not belong to the local administrator or power users groups, or any custom group and the user is not part of the domain administrators group, but user show that it is admin

  I did a gpupdate/force and restart twice PC
  Yet, user indicate it is always admin when we right click on Start menu and see the possibility to open all users

  Hi elena_ad,

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the public on the TechNet site. Please post your question in the below link:

  http://social.technet.Microsoft.com/forums/en/winserverManagement/threads

• Is it possible to add local groups and users on Windows 7 Home Basic Edition?

  She is trying to help someone solve the problem of having with what she said, it is Windows 7 Home Basic Edition.

  See said that it is a purchased laptop recently and that she had already used the local users and groups on this laptop, and now she is no longer able to see.

  I told her that I was pretty sure that the local users and groups was not available in Windows 7 Home Basic Edition, but she said she had "activated" (his words) at the store where she bought and was able to add a new user, because it was part of his mission in M/S of SQL...

  Is this possible? Are there options to do? It doesn't make sense to me, so I thought I would post it here.

  Thanks for any idea that you can afford.

  Is this possible? Are there options to do? It doesn't make sense to me, so I thought I would post it here.

  Windows 7 Home Basic Edition under the snap-in to manage local groups is not included. However, you can do the work manually as follows:

  1 log in under an administrator account.

  2. click on the start planet.

  3. type cmd.exe in the search box.

  4. press on Ctrl + Shift + Enter

  5. click on "run as Administrator".

  6. type the following commands and press ENTER after each:
  net localgroup "Family" / Add
  net localgroup
  net localgroup 'Family' 'Jack' / Add
  net localgroup "family".
  net localgroup 'Family' 'Jack' / del
  net localgroup 'Family' / del
  The meaning of the switches should be obvious.

• Secondary ACS authenticates not to dynamic users

  Hi all

  I have two ACS server for windows with version 4.2. My problem is that, if the primary ACS server is down, dynamic users from the database windows in unable to authenticate with the ACS secondary. Please note that if a user is added to the ACS, this user can authenticate with the windows database. Only the dynamic mapping is not the case with the second ACS server.

  A quick response will be appreciated.

  What is in the database of Windows in both the points of the unknown user policy? Dynamic users are active under the unknown user policy?

  Are these servers ACS for Windows or the ACS SE with a Remote Agent installed on a member of the AD Server?

  If they are remote Agents, see the external database > Windows Configuration > selection of the Remote Agent. The same remote Agent is selected on both ACS servers?

  Please be aware that if you change the order of the RA he would remove all your group mappings.

• Search ACS 4.2 order unknown user from database

  Hello

  I have several user databases in the search order for the unknown user policy. Ignoring the manual (http://www.cisco.com/en/US/partner/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/UnknUsr.html#wp277530), which States that, after the failure of authentication from the first database (Windows) the ACS does not continue to look for the second database, a RADIUS server. I see that, with the failure in the first user, database stops the ACS research and fails to the user authentication with an authentication failure code "external DB password invalid.

  Documentation not going or is this a bug in the ACS v4.2.1? How can I make the ACS to continue to seek the second database user?

  Hello Roberto,.

  If the external database returns an invalid username/password, then it is intended for ACS is not to check the following data in the sequence and the failure of authentication:

  http://www.Cisco.com/en/us/partner/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/UnknUsr.html#wp277502

  "For authentication requests, ACS applies the unknown unknown user policy to users. ACS does not backup to the known or discovered users authentication failure unknown when user authentication support. »

  If you want that ACS to verify the following database, even if a response from the invalid username/password has been received, you will need to explicitly set this on the external Windows database configuration page, in the section entitled 'Strategy for the unknown user' (but on the database configuration page specific Windows, not covered by the unknown user policy) :

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2.1/User_Guide/UsrDb.html#wp354338

  In addition, on the previous screenshots, I could see that you have configured both as a result of database:

  Windows database

  RADIUS Server token

  So we may be running into a situation where the authentication method used is not supported by the tokens, Radius servers, and therefore impossible to check the second database in the list:

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2.1/User_Guide/UsrDb.html#wpxref36799

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2.1/User_Guide/Overvw.html#wpxref846

  Kind regards

  Fede

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• local group can be used for authentication to the remote user?

  Hello

  Can I use local user databease created the PIX as authentication method for remote access VPN clients. When tried to make using PDM following error has been shown

  "Local group is not taken care of for the user remote auth.of a client remote easy vpn." Please select another group of servers auth... »

  Snapshot of PIX is attached.

  This cliché is: suite menu.

  ---> VPN configuration---> remote access--> vpn cisco client---> select the Group---> edit--> Advanced-->

  Is there is another way, what can I use the local PIX basic data itself to authenticate users from the outside world of the VPN client.

  no doubt this pix is able to authenticate the user remote vpn against its local database.

  Here are the code examples:

  access-list 101 permit ip 192.168.1.0 255.255.255.0 10.1.1.0 255.255.255.0

  access-list 120 allow ip 192.168.1.0 255.255.255.0 10.1.1.0 255.255.255.0

  (Inside) NAT 0-list of access 101

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 3des encryption

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  ISAKMP identity address

  ISAKMP nat-traversal 20

  Crypto ipsec transform-set esp-3des esp-md5-hmac vpnset

  IP local pool ippool 10.1.1.11 - 10.1.1.21

  vpngroup address ippool vpnclient-pool

  vpngroup idle 1800 vpnclient-time

  vpngroup vpnclient-Server dns 139.130.4.4

  vpngroup vpnclient password cisco456

  vpngroup split tunnel 120 vpnclient

  Crypto-map dynamic dynmap 10 transform-set vpnset

  map remote_vpn 20-isakmp ipsec crypto dynamic dynmap

  Cisco username password cisco123

  AAA-server local LOCAL Protocol

  client authentication card crypto remote_vpn LOCAL

  client configuration address card crypto remote_vpn throw

  client configuration address card crypto remote_vpn answer

• A user in domain local group administrators is not administrator rights

  Trying to figure out what the problem is with the computer of a friend at work.

  When you connect as long as domain user that is part of the local Administrators group, the user looks like he doesn't have administrator rights. For example, they are unable to create files in certain folders, etc where you wait for only admin to be.

  If the computer is in safe mode, then everything works as expected.

  If the same newspaper users in another machine on the network, while everything looks ok.

  It just seems to be on a machine that he has problems.

  All local group settings look ok and permissions on individual files look ok - and they work in safe mode.

  This is a friends working machine, and for now, he tries to avoid his reconditioned machine to work around this problem. There is no restore point for him to try (it's out of our hands). We tried a number of things right, but nothing was any use so far - other than to try safe mode, but we do not know how to use this info.

  Any advice on how this track more would me much appreciated!

  OK, now that we are talking about. The files you mention are all the system folders. They enjoy special protection under Windows 7 to prevent rogue programs to do things behind your back when you are signed in under an administrator account. It goes the same for the root of C:. You can create folders here, but you cannot create files.

  Click Start, click Help, and then seek help on UAC learn more.

• option to Editor local group policy for the administrator account on Windows 7

  I have an administrator account I want to restrict in some respects. I know that this can be done via local group policy. So, I need:

  1. Installation of new programs require an admin password.

  2. Some programs (that I choose) run without admin password.

  3. Held together under one account, without comments, accounts of users or lower privileges.

  No idea how to do it?

  Hello

  Thanks for posting your query on the Microsoft Community.

  According to the description of the problem you had to restrict access to some programs using the local Group Policy Editor. The Local Group Policy Editor is a snap Microsoft Management Console (MMC) that provides a single user interface through which all the settings of local Group Policy objects can be managed.

  I suggest you to return the article mentioned below and see if it helps you to solve the problem.

  Local Group Policy Editor

  Group management strategies for it professionals

  Hope that the information provided is useful. Let us know if you have any concerns related to Windows. We will be more than happy to help you.

  Kind regards

• Global group to the Domain Local Group

  Are there conversion issues a global group into a universal group and then promote the universal group to a domain local group. The global group is currently not member of any other groups while users currently reside in the global group - thank you

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• I can't create the local group on vSphere Client 5.5

  Hello, Hello all!

  I'have the vSphere Client 5.5 and I cannot create a local group on the tab "local users and groups. When I create a group shows me an error and I can not create it. This is the error that I have:

  Call "HostLocalAccountManager.CreateGroup" of object "ha-localacctmgr" on ESXi 'IP' failed.

  I am connected to the root.

  I saw in other forums that it is impossible to create groups due to the last version is only possible in the Web Client that comes integrated with vCenter.

  In the old versions is possible, but when I open a session in vSphere Client 5.0 for example, I have to update version and I can't use the 5.0 version.

  How can you help me?

  Thanks and greetings

  PD: Sorry for my bad English

  Hi Danisb3,

  It seems that local users is now the recommended around work (see link above), but as you said if you have vCenter you can add groups

  ESXi 5.1 and later versions does not support local groups. However, Active Directory groups are supported - is it possible to connect to AD?

• Lack of local groups of SQL Server service causing my upgrade failed... (SQL2008R2 to SQL2014) emergency assistance

  Hi all
  I have problems with the upgrade of SQL Server 2008 R2 at SQL2014 with the error "no mapping between account names and security IDS was done" and the reason for the error is SQL server local groups that were created during installation (SQL2008 R2) are not on the local server groups.
  Can anyone help identify the good fix for this problem?
  SQLServerMSSQLUser$$MSSQLSERVER
  SQLServerSQLAgentUser$$MSSQLSERVER
  SQLServerReportServerUser$$MSRS10_50.MSSQLSERVER
  SQLServerFDHostUser$$MSSQLSERVER
  Please let me know if you need any further details.
  Thank you
  Naz
  S/N

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• Open the local Group Policy Editor

  How to open / run local Group Policy Editor?

  What operating system?

  Vista:
  Click Start
  In the box, type search in gpedit.msc

  XP:
  Click Start
  Run
  in the Run dialog box type gpedit.msc

• How can I run GPedit.msc to start local Group Policy Editor

  I greye system icons in the task bar, I need difficulty do not know how to run GPedit.msc to start local Group Policy Editor

  What version of Vista you have?  Unless he's professional, Ultimate or Enterprise (maybe), you don't have this ability.