ACS 5.3 and Auth command

Similar Questions

• Ganymede + auth-proxy on acs 5.0 and later support?

  The nas is 2801 with ios 15.1 and acs 5.3.i want to deploy auth-proxy using Ganymede + protocol.but there no work.using RADIUS is ok.

  I want to know Ganymede + auth-proxy on acs 5.0 and later support?

  Thank you!

  GANYMEDE + Auth-Proxy is only supported after ACS 5.3 patch 5. Upgrade your ACS 5.x or use RADIUS for authentication Proxy.

• WLC / ACS / AD - domain and laptops no - domain (802. 1 X / PEAP)

  Hi all

  I implement a solution based on 4404 WLC, 1113 ACS and Microsoft AD. What I want to achieve is to have two WIFI (SSID), that can be used by users on laptops of the domain, the other can be used by the users in the domain on personal laptops. Field portable computers will have full connectivity, but personal laptops will be restricted.

  I created the two SSID using 802. 1 X by ACS / Remote Agent and can authenticate and connection OK.

  I thought I should have user auth and auth machine for laptops of area but just user auth for personal laptops.

  I have unauthenticated machines go to one group ACS or blocked, but I need to enable them in if they are on the SSID restricted. I can't quite understand how to have two SSID is authenticating with the same ACS / AD - one green and the other.

  I'm on the right track?

  Anyone done this before or have any bright ideas?

  See you soon,.

  John

  With the use of WLAN access based on the SSID, users can be authenticated based on the SSID they use to connect to the WLAN. The Cisco Secure ACS server is used to authenticate users. Authentication happens in two stages on the Cisco Secure ACS:

  1 authentication EAP

  2 resulting SSID authentication of network (NARS) on Cisco Secure ACS Access Restrictions

  For the new designation and configuraiton following URL can help you:

  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a00807669af.shtml

• Cisco ACS 5.1 Machine Auth problem

  Hi all

  I have a question about ACS 5.1 using EAP-PEAP (auth more user computer name and password). I managed configuration AD authentication with user credentials and auth of Machine and it works well for users and wireless peripheral companies.

  My rules ACS machine auth against computers AD that gives a positive/pass, then a rule against the user but check if unit is a unit of area valid with "has been authenticated machine = TRUE".

  The problem is when you use a Windows 7 device (laptop) and connect you using the local administrator account, I connect successfully to the network but the local Admin account is not in the AD. By default wireless adapter the W7 under Security > advanced settings > specify the authentication mode is only computer authentication.

  Does not send the client of W7 on credentials of the user?

  Has anyone encountered this problem before? Do I need to tweek client W7 via GP or is there a way to stop all machine authentication with a valid user name and password?

  Really appreciate all the responses and I thank you in advance.

  Jason

  Check

  http://TechNet.Microsoft.com/en-us/library/dd759219.aspx

• ACS 5.4 and Juniper J-Web

  Hello

  I have set up a box of the ACS 5.4 and will test the devices on it.

  Cisco and Juniper, both works well with GANYMEDE

  I can connect both the use of SSH or Telnet but my problem is the Juniper J-Web GUI

  I can't access the J-web no problem with the root account.

  I can't seem to make it work, no matter what I try. Here is my shell of the GBA box

  

  And the following configuration of Juniper.  I tried to bind the local-user-name attribute to the remote and remoteadmin with no luck. Anyone got any ideas how I can fix this problem? Or if its even possible?

  version 9.6R1.13;

  System {}

  host name of Juniper-pare-fire;

  authentication-order [tacplus password];

  {root-authentication

  password encrypted "$1$ $1tRuy9o2 LwSPxNwe4XGNMOMIMo1pd1"; # SECRET - DATA

  }

  {tacplus-Server

  10.251.200.25 {}

  secret ' $9$ zaUL6/AtuOIRS5QF/CuEhws2 "; # SECRET - DATA

  Timeout 10;

  Single-connection;

  }

  }

  accounting {}

  events [connection change-journal interactive-commands];

  {destination}

  tacplus;

  }

  }

  {Login

  the user admin {}

  UID, 2001;

  root class;

  {authentication

  password encrypted "$1$ MNUZBLFW$ X2sJL/UTgRYcgBNV4RLe.0"; # SECRET - DATA

  }

  }

  user remote {}

  full name of the "remote user";

  UID 2025;

  operator class;

  }

  the user remoteadmin {}

  full name of "Remote Admin";

  UID 2026;

  root class;

  }

  }

  services {}

  SSH;

  Telnet;

  Web-management {}

  {https}

  System - certificate generated;

  interface fe-0/0/0.0;

  I worked on almost similar issues today and he confirmed that he is able to access J-WEB with the credentials of Ganymede. You can check the config here: https://supportforums.cisco.com/message/3953224#3953224

  Through your config it seems that you have not defined/created classes as he did:

  for example:

  {Login

  class CLASS Number {}

  permissions [view configuration];

  }

  class CLASS RW {}

  permissions in full;

  }

  user {JUNOS-RO

  UID 2000;

  Jatin kone
  -Does the rate of useful messages-

• Send data and receive commands by VBAI of VB or c#

  Hi, anyone has examples on how to send VBAI data and receive commands by VBAI of VB or c#.

  I intend to hand over command to the VBAI on and outside, get the image and stop start.

  For the data to be send are the result of the calculation of the calculator function. The data send each time to do the math.

  I have search the forum and I know that this can be done by using labVIEW. However, due to the requirement of the question, I can't do it using labVIEW.

  Thank you.

  Yen

  Hi Yen,

  "" "You're almost there. '" Here are the steps for this example works.

  Once you open the inspection in Vision Builder, go to tools > Communication Device Manager...

  You must create a Modbus master device, which corresponds to your communication of VB with Vision Builder application.

  Click on the new device. Give it a name, say "VB program".

  Select Modbus TCP for the Protocol.

  Click OK.

  On the Modbus server line, click Start Server. This starts the background task which is listening on port 502 for incoming Modbus messages.

  Click OK to exit the dialog box.

  Now, a couple of things to understand about Modbus: the Protocol specifies how a device Modbus master can read and write registers located on a slave device. Vision Builder has 4 64 k save tables:

  -Coils (read/write binary, by the master).

  -Tor inputs (binary, not read by the master).

  -Entrance to the registers (16 bits, not read by the master).

  -Holding Registers (16-bit, read/write by the master).

  The tolerances of the inspection reading read minimum and maximum intensity in Modbus 0 x 0 and 0 x 1 operating records.

  If you want your VB application to write these values.

  Here's the Modbus function codes. You can get the full list by downloading the specification to Modbus.org Modbus.

  0 x 01 reading reels

  0x02 read discrete inputs

  0 x 03 playback record keeping

  0x04 read input registers

  0x05 write single coil

  0 x 06 write single register

  0x0F write multiple coils

  0x10 write multiple registers

  To use your example Modbus program to read and write registers Vision Builder, first enter the IP where Vision Builder is running:

  127.0.0.1 (localhost)

  For this example, use the function Code 6 to write a single business registration.

  The Modbus data must be formatted as follows: the first 2 bytes are the starting address, the following 2 bytes are the value (U16) you want to write to the registry. So to write the value 1 at 0 (corresponding to the intensity of the min), the data value Modbus 00000001. Click on send.

  Now, to set the maximum intensity at 50. Set the data to 00010050. Click on send.

  Step write data written minimum intensity of step to check the presence of CAP in the Modbus 0 x 0 registry entry and the status of the step in discreet entrance 0 x 0.

  To read the intensity Minimum written by VBAI, the value of the function 4 Code (enter reading registry). For the Modbus data, the first 2 bytes represent the address, 2 bytes, the number of registers to read. The value of data Modbus 00000001 to read a single registry entry to address 0. Click on send. The response data can be for example 0x1E, which corresponds to 30 decimal places.

  To read the status of the step, set the function Code 2 to read discrete inputs. The value data 00000001, to read the first register of the discreet entry table located at address 0. The response data is 0 or 1 (success or failure).

  I hope this helps. Let me know if you need other information. But this should help you get started.

  Best regards

  -Christophe

• GPIB read and write commands of Agilent 54642 oscilloscope

  Dear friends,

  I would like to acquire a waveform of Agilent 54642 ocsilloscope in the LabView 7.1 via GPIB program. Can anyone mention the GPIB read and write commands for the oscilloscope even?

  Furthermore, on the subject of the LabView program, is it fair to place blocks to write two GPIB followed by a single GPIB read block (everything series), as well as an indicator, in order to check the waveform in LabView?

  Kindly help me with your answers...

  Look forward to y...

  Thank you very much in advance...

  Marion

  Download the 7.0 driver that Albert gave the link to, make sure that you have installed NI-VISA and run the getting started sample which is part of the pilot. If it does not, please elaborate on the error codes that are reported.

• Cannot run chkdsk/f of the safe atmosphere and the command prompt

  Cannot run chkdsk/f of the safe atmosphere and the command prompt

  Separated from the:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_install/run-chkdsk-f-to-check-for-hard-drive-corruption/05a2345a-a81e-4C44-A24B-ad299987a44c?page=2#LastReply

  Hello

  See if that helps you.

  "How to run the check disk at startup in Vista or Windows 7"

  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  You are missing a space in the command:

  Type one of the following commands to run Chkdsk:
  NOTE: The most common command is chkdsk /f or chkdsk C: /f

  See you soon.

• Removal of road static and led commands

  I can't seem to find it in the docs anywhere - how does one remove static, leads, and route commands on a Pix 515, v5.3? Can we simply type the word 'no', followed by the command?

  Thank you.

  Hello

  You can simply type "no" followed by the command. But you must be in config mode to do this.

  Kind regards

  Tom

• is windows 7 support rcp and rsh command line routines

  is windows 7 support rcp and rsh command line routines

  It seems that they fail... Tried to install subsystem for unix applications based, still is not there... :(

• ACS, Service access and authorization

  I'm under ACS 5.2 and I'm trying to set up 3 new SSID, which 2 are not guaranteed and 1 which is secure.  I'm trying to understand the best way to allow their evolution on which network they come.  All authentication requests are from the same devices, LAN controllers without wire, so NDG cannot be used as criteria.  I was watching either create 3 Access Services and using selection rules, or by creating 1 Service access and using permission to choose.  However, I can't find an attribute to use for determining what network they came.

  Anyone has a suggestion for the best way to do it?  I have

  Go to the elements of the policy-> Conditions of network-> end of Station filters and create a rule CLI/DNIS that includes the name of the SSID, and then use it as a condition to any rule you create for authentication. The SSID will be preceded by MAC address, then enter * ssidname (i.e., match whatever it is before the name SSID, then match the SSID). For example, if the SSID is called lab, then you must enter * lab.

  Then go to access-> Service selection policies and create a service selection rule that has end Station filter as a criterion.

• ACS 4.0 and IBM TSCM

  Hello

  I try to load the attributes of the CNA for IBM Corporation (TSCM) of the FTP (the attributes of the NAC management), but these do not appear in the system

  Configuration-> Configuration-> CSV connection failed attempts Configuration or CSV file past Authentication Configuration file.

  My server is ACS 4.0 device. On ACS 3.3 my attributes of the NAC is working well.

  [attr #0]

  Vendor id = 2

  name of the vendor = IBM Corporation

  application = 50 ID

  SCM = application name

  attribute id = 00020

  attribute name = political Version

  Profile attribute = off

  type of the attribute = string

  [attr #1]

  Vendor id = 2

  name of the vendor = IBM Corporation

  application = 50 ID

  SCM = application name

  attribute id = 00021

  name of the attribute = number of Violation

  Profile attribute = off

  type of attribute unsigned whole =

  [attr #2]

  Vendor id = 2

  name of the vendor = IBM Corporation

  application = 50 ID

  SCM = application name

  attribute id = 00010

  Action = attribute name

  Out = attribute profile

  the attribute type = String

  I loaded the list with attributes for Symantec on ACS 4.0 and it is OK, but for Tivoli Security Compliance doesn't work.

  Please help me if you have a solutions!

  Thank you!

  Hello

  Well Yes, you can't have a space between the name of the seller, I case that after loading the file I do not have the attribute of the GBA unit, but can see logging. After the reboot of the ACS that's ok.

  I also, can deployment of the NAC with IBM TSCM, you share the experince? What version of client TSCM, we should use? I can't get the 5.1.0 version but it looks like no need version 5.1.2 above only can patch the last update.

  Thank you

• Problem ACS 4.0 and Server RSA Token

  Hello

  We are having a problem trying to get 4.0 for Windows GBA authenticate users on a Server Token RSA wireless.

  Our Cisco 1200 AP series is configured for WPA2 and LEAP Authentication. He points to the ACS server for RADIUS authentication. Now, it works very well for users with a static password defined on the internal database of GBA. However, for obvious security reasons, we? d as the transmitted authentication to our server internal RSA.

  I installed RSA Agent on the same server as the ACS along (after adding the sdconf.rec file in the System32 folder). The RSA server was added to the ACS external database and a user configured to use the Token RSA server for password.

  When we try to authenticate, the ACS fails the attempt with reason? External DB passes invalid?. The same user can authenticate successfully during the use of the RSA test authentication tool that is installed on the ACS server under the RSA Agent software.

  After running some debugs a pix in front of the servers, I see traffic to and from the servers when you use the test tool (that works), but it looks like GBA doesn't? t even send traffic to the RSA server during authentication.

  Any help or advice appreciated.

  Thank you

  no no no no! Do not use EVER of RSA with WIFI + PAP.

  The token + pin can be sniffed and is good for 60 seconds... on the Wifi which is disastrous.

• I tried all day offer of 10 image and the command of Adobe stock. Whenever I tried it, an error message appears.

  I tried all day offer of 10 image and the command of Adobe stock. Whenever I tried it, an error message appears.

  Could you please re - enter your payment details in the account management page, save it and try again.

  Please let us know if you continue to have problems.

  Thank you

  Bev

• Difference between the TOP and ESXTOP command.

  VMware dear Experts,

  I just want to know the difference between the TOP and ESXTOP command, once I run top command or esxtop command I m getting different statistical load CPU, following is the blink of an eye the same.

  

  concerning

  Mr. VMware

  u mean we will not be able to run the command "top"?

  That is right.

  The time and date of this login have been sent to the system logs.
  
  VMware offers supported, powerful system administration tools.  Please
  see www.vmware.com/go/sysadmintools for details.
  
  The ESXi Shell can be disabled by an administrative user. See the
  vSphere Security documentation for more information.
  ~ # top
  -sh: top: not found
  ~ #