ACS command authorization mode t conf report

Similar Questions

• Specific shell - ACS command authorization / GANYMEDE + on 2900XL

  Hello all-

  I was struggling with a particular issue here. I am running ACS 3.2 and tries to implement secure access to my switch. I have 'students' of my University I want to leave running specific functions, i.e. change the vlan port and write in memory, etc.

  I created with success the piece of the authorization, and my test account can connect. I have successfully assigned a privilege level of 7 also, that gives me a look of default base rights. Accountants strives also, indicating connections and commands me to come home.

  I want to do is use ACS to allow a particular group of controls, so I can change if needed in one place (ACS) and I not touch + 400 devices. ACS says can be done, but it doesn't seem to work. I created a Shell command group and specified commands, no luck. Even if I change the 'unmatched orders' rocking 'allow' (which should allow all orders, right?) it does not yet allow all orders. I added the Shell command group for the group, of which students are members...

  My AAA commands are as follows:

  AAA new-model

  AAA of default login authentication group local Ganymede +.

  Group AAA authorization exec default local Ganymede +.

  AAA authorization commands by default 7 Group Ganymede +.

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 7 by default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  AAA accounting system default start-stop Ganymede group.

  Any ideas? Any thoughts?

  Thank you!

  Michael

  QU.edu

  Michael,

  You perform permission to order order that exist with a privilege level of 7. By default, the configuration commands have a privilege to 15. There are two ways you can go about solving this problem. The first would be to authorization of installation for level 15 command. The second would be to change the privilege level of the commands that you want your students to be able to run level 15 at level 7. This can be done with the command of privilege. Here is a link that shows the use of the technology locally within the unit. http://www.Cisco.com/warp/public/480/Priv.html

  I don't know if the ACS can push the configuration of the device on a per user basis, so the first option may be your best bet. Be sure to allow access to all controls for yourself.

  Steve

• Command authorization Config 3.3 ACS

  Hello

  I want to allow a user only add/remove the roads on a router. The shell command authorization works very well. But when the user is in configuration mode, it can start with any order!

  Debugging says:

  1w2d: AAA/AUTHOR: authorization config command not enabled

  How can I activate this and how/where can I he set up the GBA?

  Thanks in advance

  GBA just allow the user to enter the command 'road' as if you have any other shell command that they are authorized to do.

  On the router/NAS, you must tell him specifically that you want authorization for config commands with the following:

  AAA authorization config-commands

  Note that the format of this command changes slightly on different versions of IOS, but if you "aaa authorization?", you will be able to understand.

• ACS command 4.1 authorization failing intermittently

  Hello

  I have installation switches aaa using Ganymede + on the network, however I seem to get occasional command authorization error. It shows when I try entering the command on multiple ports at the same time (example interface range giga 1/1-48). If I had to do on one lane instead, I does not seem to encounter the error. It would be because of the ACS, unable to carry the load? It is only for a single switch to run the command for port ranges.

  I've attached an example of the error of reference:

  switch (config-if-range) #description level 3
  % Failed authorization.

  % Command failed on the beach of the interface. Abandonment

  I checked the interface to connect to the ACS, and I see no error. I'm not too sure of what may be the cause of error. Would it be because of the ACS unable to work well with the range of interface?

  Thank you.

  There is a bug open for this issue which is found in subsection 12.2 (46), and for the moment there is no plans how to solve the problem because it involves a design work in the code to fix this. The only work around is to remove permission to order or to see what your limit is on the beach inteface command entered begins to drop requests.

• Shell command authorization

  Hi all

  I'm having a problem with the Shell command authorization. I have a user that I just want to be able to display the configuration of installation, it is for the auto config to archives on an hourly basis.

  I have configuered the device with the following orders of aaa:

  AAA new-model

  AAA group Ganymede Server + ACS

  AAA authentication login default group ACS

  /NOAUTH AAA authentication login no

  AAA authorization config-commands

  AAA authorization exec default group Ganymede + group ACS

  /NOAUTH AAA authorization exec no

  AAA authorization commands 15 default ACS group

  AAA authorization commands 15 /NOAUTH no

  AAA accounting command 15 arrhythmic default group ACS

  The static account I have set up ok logs and can show config etc. Access to the conf t is disabled, which is good, but for some reason, it can run any command show rather than just who is this all I welcomed in the Shell command authorization.

  Unmatched command is defined for refuse and allowed unparalleled arguments are not checked.

  ACS is 3.3 2 and switch I tested running 12.1 (9) EA1

  Any ideas?

  Most of 'show' command are level 1 controls. You can check this by logging in as a normal user, issue a private "sho" to make sure that you are at level 1, and then type 'sho ip road', "sho ver", etc., you will see that all work fine.

  Your AAA commands say only the switch to allow level 15 commands, so when you do a "sho ver" or similar this order will not be sent offshore to the ACS server for authorization.

  If you add the following:

  AAA authorization commands 1 default ACS group

  so, what do you have to fix, but be careful because it is easy to lock you out of power mode enable (add 'enable' in your command set too).

  You should also noticed all those who 'show' commands were not their statement in detail either, because you have enabled also only accounting for level 15 commands.

• ACS - ASA authorization and accounting

  Hello

  I have a few questions about the authorization and accounting on the ASA via an ACS server

  1. When I activate the command 'aaa authorization command' users of SSH commands I get locked on console then I have to configure the console, telnet and allow to be authenticated via Ganymede too, is it possible to allow SSH via Ganymede while keeping the Console and telnet authenticated locally or not even no authentication?
  2. I visited command 'aaa accounting TAC' accountant on ASA, but I noticed that GBA records just mod configuration commands ' focus on in 15 "not show all command or privilege 1, is possible to fix this?"»
  3. RADIUS supports authorized SHELL?

  Thank you for your support

  1.] Unfortunately, it is currently not possible to exclude the command authorization serial number / console or ssh to users while having it apply to other methods of access in the case of ASA. Once you run this command, it would be applicable to all methods such as ssh, telnet, http, enable and console. This can be easily achieved by IOS (routers and switches) by creating a list of method.

  2.] when configuring the aaa accounting command , each other than display command command commands entered by an administrator is recorded and sent to accounts or servers. This is a default behavior on the SAA. IOS send/check orders show on ACS/Ganymede.

  http://www.Cisco.com/en/us/docs/security/ASA/asa81/command/ref/A1.html

  Kind regards

  Jousset

  The rate of useful messages-

• Problem with shell command authorization

  I came across this issue with ACS 3.1 and 3.2 of the ACS

  A shell command authorization set is created under the profile shared with the following components:

  Unmatched orders: refuse

  Permit of unmatched Args: UNCHECKED

  The order authorized is 'show' with the Arg "worm permit", "allow the interface" and "allowed to run.

  This permission set is then applied to the group, under the option "Assign a Shell command authorization on any device on the network."

  Select this group option is set to 'Max privilege for any customer of AAA, level 15.

  This configuration is then tested against two IOS switches, with orders from aaa as follows:

  AAA new-model

  AAA authentication login default group Ganymede + local

  the AAA authentication enable default group Ganymede + activate

  AAA authorization exec default group Ganymede + local

  AAA authorization commands 15 default group Ganymede + local

  The problem I have is that when a user who is part of this group connects, it can issue commands such as see the worm, see the race and show int just as I would expect. Any command that does not begin with a show... is denied. However, other show commands that do not appear in the arguments of will work, so that some don't. For example, "show arp" and "vlan" worked, while "show accountants ' and 'buffer' does not. What Miss me?

  commands that work without explicitly set them are of privilege more low level 15... for example; "show arp" is a command of Priv-1, so it is execuatbel without permission of command as you do not permission to order for private-1.

  Router > sh priv

  Current privilege level is 1

  Router >

  Router >

  Router > show arp

  Protocol of age (min) address Addr Type Interface equipment

  Internet 10.1.5.2 24 0000.abcd.abcd ARPA Ethernet0/0

  Internet 10.1.5.3 - 0003.abcd.abcd ARPA Ethernet0/0

  Router >

  Router >

• Connection of ACS command line...

  Hello

  I have a superadmin account with ACS.

  with this account, I can't able to connect GUI but can't login CLI mode.

  What could be the problem?

  Hello Tony,.

  ACS GUI administrator and CLI administrator accounts are different. You cannot log in with accounts of MISTLETOE in CLI.

  You must use CLI accounts created to access the ACS command line. You must have created one during installation first GBA 5.x.

  If this was helpful please note.

• series PIX command authorization

  Hi all

  can someone tell me please the use of GBA pix command authorization. I understand the use of a shell command authorization.

  I'm sorry if the question is too dumb. I am completely new to this sector.

  Thanks in advance.

  concerning

  Kirti.

  Pix command authorization set was designed to set up approval order with PIX/FWSM, as shell pix did not differ for IOS, but at the launch the actual code, PIX/FWSM seems to work correctly with the auth command sets the shell.

  So no one is really interested in using shell Pix more, more to watch new codes of pix it seems that developers are more likely making Pix Shell same shell IOS, so even if they stop PIX command sets in the next version of ACS I will not be surprised.

  ~ Rohit

• The AAA command authorization

  I have an ACS 4.0 device. In the shell command authorization set section, you can define authorized or rejected orders (see) and arguments (running-config). I'm limiting users to a set of specific commands. One of the commands is "exit". To my knowledge, "exit" has no arguments. If I add 'Quit' as a permitted command but nothing come to the section of the argument, I get the authorization failed on the router. If I select "unparalleled stay args" (of output), the authorization is successful. I would prefer not to select "unmatched args to stay." Is there an argument for "out" I'm not aware of?

  Hello

  Try this,

  exit - permit

  represents returns the key.

  Kind regards

  Prem

• command authorization failed

  I turned on the aaa command authorization without applying the correct user privileges. I can now log on this user, but the ASA 5510 displays an error:

  ============================

  EUKFW2 # show running-config

  ^

  % ERROR: invalid input detected at ' ^' marker.

  ERROR: Failed authorization control

  ============================

  I'm unable to change the configuration of the firewall. Is there any default user through which I can connect and disable the authorization of aaa? If this is not the case, how can I solve this problem?

  Please visit this link

  http://www.ciscotaccc.com/Kaidara-Advisor/security/showcase?case=K10386224

  Please evaluate the useful messages

  Kind regards

  ~ JG

• How to activate 'Shell command authorization games '.

  Hello

  I use aaa on Ganymede to check the user to active directory ms.

  I set up a new "Set Shell command authorization" see the attachment for more details.

  But it does not work. So, I just want to check if the use of a command works or not.

  You can see in the file attached, I tried something with the command 'show '.

  But if I connect I am still able to use "view aaa servers" example, but in the 'show' commandbox I asked the agrument "refuse the aaa" inside.

  Why doesn't this work?

  Thanks for the help

  BB

  BB,

  Not sure why you want to do it this way. Trick here is to give all users a priv 15 and then set the permission command, defined according to your need.

  Overlooking priv 15 does not mean that the user will be able to run all the commands. You can set permission set and allow that you want specific orders, the user should be able to run.

  So pls rate this help

  Kind regards

  ~ JG

• Help ACS shell command authorization

  Hello

  I wanted to only allow users to use the command interface. But when I have enabled terminal config of ACS shell command, all commands are allowed. How can I limited users having only permission for command interfaces?

  Thank you

  Two things may be wrong

  (1) you do not have the following command on your AAA Client:

  AAA authorization config-commands

  (2) you have clicked on the 'unmatched orders' = allowed radio option in ACS, take a look on:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2086/products_configuration_example09186a00808d9138.shtml

  Concerning

  Farrukh

• ACS 5 - question about monitoring and report

  Hello world.

  I have one primary-secondary drawing using DCC 5, and everything works smootlhy. I have some doubts and did some research, but nothing was clear enough on this subject:

  -Why am I not able to access the visualizer reports & surveillance of my secondary box? When I do that, I get redirected to connect to the main box. Is this expected behavior?

  -If Yes, what should I do if my main box breaks down?  Should I manually promote my primary secondary box? Or y at - it a way to allow the two ACS for these newspapers?

  -Another situation: my box main breaks down in the middle of the night and I only notice the morning.  What happens in the newspapers at the moment? Are they lost?

  That's close enough for now.

  Thanks a bunch

  -Victor Alves

  Hi Victor,

  If you are unable to access the visualizer reports & surveillance in your secondary zone and are rerouted to connect with the main box. This is expected behavior if your backend is defined as collector of newspaper.
  A primary server or one of the secondary servers can function as a logging server. The logging server receives logs of the primary and all secondary servers of the ACS in the deployment.
  You can also configure another server as a Syslog server (ex Syslog target remote server) in addition to the logcollector.

  The newspaper collector failover process is not automated and manual. If your collector journal defined as main server goes down, you can then promote the secondary server in the primary and then manually set as a collector: ACS GUI > System Administration > Configuration > Configuration of logs > Log Collector
  A possible workaround for this problem solution is to assign one of the ACS secondary servers under the supervision and report server according to the Cisco documentation links included below.

  For a situation with main server configured as collector of newspaper is down, registration will be unavailable as a result of this proceeding.

  For db/corruption issues, if you have valid backups before the failure, you would be able to use the rollback feature to have information before the acs services down.

  For reference links:
  http://www.Cisco.com/en/us/partner/docs/net_mgmt/cisco_secure_access_control_system/5.2/installation/guide/csacs_deploy.html#wp1104098
  http://www.Cisco.com/en/us/partner/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/logging.html
  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.2/command/reference/cli_app_a.html#wp1888749

  HTH,

  Please let us know if it concerns pending.

  Thank you

  Alex

• Put in command button Mode loses the callback function

  NOR expensive.

  I have a code I want to change the buttons toggle robot (according to different scenarios). However, if I put the command Mode of the button disabling at VAL_INDICATOR or VAL_NORMAL for this button, the callback function ceases to be called when the button is pressed.

  What is the defined behavior?

  I use 8.0.1 (356) CVI

  Kind regards

  Brian

  Yep, the VAL_HOT did the trick.

  A big thanks to dsappet and jr_2005 for taking the time to investigate this.

  Much appreciated!

  Kind regards

  Brian