adapter net 1394 Windows xp

Similar Questions

• HP p2-1394: what printer will work with HP p2-1394, windows 8.1

  What printer will work with HP p2-1394, windows 8.1?

  Thank you.  I'll check your suggestion.

• Network adapters: Microsoft Windows Mobile remote adapter causes the Windows 7 upgrade to fail.

  Network adapters: Microsoft Windows Mobile remote adapter causes the Windows 7 upgrade to fail.

  I did everything to prepare for the upgrade. The Upgrade Advisor says it all right. But I get the message that this network adapter is a problem. It does not appear in device menager even under hidden objects, so I can't uninstall or update.

  It is obviously a problem for more than two years. Why is there not a difficulty now, or at least a well validated response that meets this situation rather than simply repeat the statement to execute the Advisor (done) or update the driver (which is impossible because the card network can not be found)?

  Hello

  You can try these:

  Step 1:

  a. click the Start button.

  (b) in the search box type devmgmt.msc and then press ENTER.

  c. find under the "Mobile Devices" "Microsoft USB Sync" node. If this is not present, proceed to the next step. Otherwise, right click "Microsoft USB Sync" and choose "Uninstall".

  When you connect your USB phone, it should appear in the device under Mobile Device Manager. Education invites you to look out there and if you find Microsoft USB Sync, uninstall it. If she is not there, go to the next step.

  Step 2:

  Disconnect, and then reconnect your device. Your device driver will be re - install and launch Windows Mobile Device Center.

• my hp photosmart C4600 Printer series does not work via my bluetooth USB 2.0 Wireless printer adapter, I run windows 7

  my hp photosmart C4600 Printer series does not work via my bluetooth USB 2.0 Wireless printer adapter, I run windows 7

  He ran once before, one of my suggestions of solution was the coil (?)  was incorrectly, but don't know how to adjust it

  Hello
  (1) have you made changes before the start of this issue?
  (2) what is the exact error message/code?
  A print spooler is software that temporarily stores the disk printing hard or in memory until the printer is ready to print. If you were expecting an abnormally long time to print a document, or if you see an error message about the print spooler, Spooler subsystem or spooler resources, you might need to change and then restart the print spooler service on your computer.

  To do this, we recommend that you save your work and restart the computer to restart the print spooler service. If you do not want to restart the computer, try these steps.

  To change or restart the print spooler service

  You must be logged on as administrator to perform these steps.

  a. click the Start button, Control Panel, click System and Maintenance and then click Administrative Tools.

  b. double-click on Services. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  c. right-click on the print spooler service and then click Properties.

  d. on the general tab, next to startup type, make sure that automatic is selected.

  e. If the service is not already running, under Service status, click Start and then click OK. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  Additional reference:
  Open printer troubleshooter.
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter
  Let us know if that helps.

• How have the Linux database server listener listen to the service in the Net of Windows XP Client Manager?

  People,

  Hello. I installed Oracle 11 GR 2 database server in the Oracle Linux 5 operating system.
  All customers (NetCA, DBCA, GROUND Deveoper, sqlplus...) works properly on the database server. The LISTENER_PT853 listener is listening on client tools under Linux successfully.

  
  I also installed Oracle database Client(SQL Developer, NetMgr, NetCA, sqlplus,...) in Windows XP. So that the client tools to connect to the database on Linux server, the listener in Linux must be tuned to the service in Windows XP.

  In Oracle Linux 5 Server Machine Net Manager:

  Service name: PT853
  Connection type: default database
  "TCP/IP Protocol".
  Host name: 192.168.196.102
  Port: 1521

  
  Listener: LISTENER_PT853
  Protocol: TCP/IP
  Host: 192.168.196.102
  Port: 1521

  
  I have test the Service PT853 with "SYS" username and password "SYS." The connection is successful.

  In the Windows XP Client computer, the information in the Net Manager is lower at:

  
  Service name: PT853_Linux
  Protocol: TCP/IP
  The host of the database Machine name: 192.168.196.102
  Port: 1521

  
  I test the connection by using "SYS" username and password "SYS" and got this error: ORA - 12514:TNS: listener does not currently of service requested in connect descriptor. There may be an error in the input fields or server may be ready to connect.

  
  Can I check the status of the listener in Linux Server machine as below:

  [user@localhost bin] $. / lsnrctl status LISTENER_PT853

  Its release: Service PT853 has 1 instance. PT853 of the Forum, State LOAN, has 1 handler for this service.

  
  Foregoing, we saw the listener in the Linux server machine only to listen to the PT853 service in Linux but not to listen to the service PT853_linux of the Windows XP client computer.

  Windows XP (192.168.196.101) and Linux (192.168.196.102) can ping each other successfully. So that client tools in Windows XP connection in Server database on Linux, the listener in Linux need to listen to on the service in Windows XP first.

  In Net Linux Manager, I add an address more (TCP/IP, 192.168.196.101, PORT 1521) to LISTENER_PT853, but gets the error.

  
  My question is:

  How have the Linux database server listener listen to the service in the Net of Windows XP Client Manager?

  
  Thanks in advance.

  UserAL1178M wrote:

  Hi you ave create listener.ora.

  Actually, no he didn't "need to create listner.ora.

  In fact, its problems stem from the fact that it * has * created one instead of letting some things by default.

  I give an example of my environment

  [oracle@home ~] $ cd /home/oracle/app/oracle/product/11.2.0/dbhome_1/network/admin/

  [oracle@home admin] $ cat listener.ora

  listener.ora # Network Configuration file: /home/oracle/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora

  # Generated by Oracle configuration tools.

  LISTENER =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = TCP (PORT = 1522))(HOST = home.test.al))

  (CONNECT_DATA =

  (SERVER = DEDICATED)

  (SERVICE_NAME = orcl.test.al)

  )

  )

  ADR_BASE_LISTENER = / home/oracle/app/oracle

  [oracle@home admin] $

  Change host, name of service depending on your environment. Your port is 1521.

  Then, first run all the listener and database startup. If you do the opposite, with that you will need to register the service change the order of system registry.

  Let me now if you need another sth

  Kind regards

• Still problems with the adapter Bluetooth Toshiba Windows 7

  Hey there, it's me again.

  I am referring to my 'Problem Bluetooth on Windows 7' subject:

  I thought after the solution of bluecat that my problem has been resolved. But it isn't really.

  After you install the Windows fix, it worked just a short time. But now the problem is the same.

  When I remove the Toshiba Bluetooth Stack and try to work with Manager Bluetooth of Windows, I see that the Bluetooth icon is to come and one to go on the taskbar. In Device Manager, I said Windows, that it is not closed the device to save power. But I think that the device is on and walk and stop...

  I really absolutely have no idea what is the problem, but I get terribly angry.

  Details:
  Windows 7
  Dell Wireless Bluetooth internal adapter 350 (but it is manufactured by Toshiba)
  Experienced pilots: Vista Pack of profile of the Dell homepage (no battery installed, driver only) / Toshiba Bluetooth Stack (the latest version)

  This is the old thread:

  Hi all

  Just as I installed Windows 7, my keyboard and Bluetooth mouse do not work very well.

  I use the Dell Wireless 350 Bluetooth internal adapter, Toshiba Bluetooth Stack 8.00.02 and the keyboard and mouse Logitech MX1000.

  To connect the devices on my computer, I first have to disconnect the Bluetooth adapter by pressing Fn + F2 on my Dell i9400, after re-login I can search and connect devices correctly. They work fine as long as the laptop is running.

  After restarting the laptop, devices no longer work. They are still in the known, but not connected Bluetooth stack. That's why I have to unplug the adapter Bluetooth, another time and reconnect in order to connect the two devices.

  I first thought, it's a Windows problem. I thought that Windows is able to ask the adapter to save power. But when I go to Device Manager, there is no box for this option, as known from other devices (Te USB Ports). If this isn't the problem. I think the problem is something else, maybe performed by the Bluetooth stack.

  Windows XP it worked perfectly. I used the same hardware and also the battery Bluetooth Toshiba (uploaded on the homepage of Dell).

  Someone at - it ideas?

  Thank you!

  Daevu

  Hey there

  Yesterday I did Format C: and installed Windows 7 news.

  I do not have a bluetooth driver for my Dell Wireless 350 Bluetooth adapt (made by Toshiba).

  And now: the mouse and the keyboard work. I even do not see anywhere in my system, but they work.

  There is no bluetooth adapter in my device manager and I had do not connect the keyboard and mouse with my computer. She simply do nothing.

  I do not understand this...

  What is a backup connection?

  What I tried:
  -> Installation more recent Bluetooth Stack from Toshiba. Problem in the above message. I also installed the MS Hotfix. The same problem.

  -> Installed "Vista profile Pack" on the home page of Dell, recommended for my laptop and Windows Vista. There is no battery installed. So I had to connect the mouse and keyboard via the Windows Bluetooth Manager. But the adapter was performed on and off windows, the icon in the task bar came and went and came and went. Connection is good, 1 minute then a few seconds. Not possible to work with the mouse.

  And now, without having to install a driver, it works. Am I stupid?

  Daevu

• Adaptive brightness in Windows 8.1

  Hey guys,.

  Since I updated to Windows 8.1 (new installation via the Dreamspark *.iso file) my luminosity is dimmed always as long as 'Adaptive brightness' is lit.

  Do you feel a similar behavior? Is there anything I could do about it?

  Hey, I found this registry fix worked for me:

  http://support.Lenovo.com/en_US/downloads/detail.page?docid=DS032287

  However, as this correction is supposed to be for a follow-up of TORSION S230U the README file and make a backup of your registry before you try!

• Performance IEEE 1394 Windows XP SP3 Adobe Premiere 6.0 problem

  I'm trying to capture video using Adobe Premiere 6.0.  When I got Win2K installed it worked fine.  I have upgraded to Windows XP SP3 and first stopped working properly.  A clean installed Matrox RT2500 - it's the video capture card, I bought with the kit Adobe Premiere - according to the instructions, as well as first - including the 6.01 update.  Now when I connect my Sony DCRTRV520 camcorder via firewire IEEE1394 and try to capture the Hi8 video I recorded, it won't record a few frames, then stops.  Matrox video tools say that the IEEE 1394 device has stopped working.  First capture options indicate that the camcorder is not recognized.

  I found a forum which indicated that the problem was with XP sp3 drivers for Texas Instruments OHCI 1394 device - indicating that the sp2 and sp3 downgraded the 1394 to S100 speed device performance.  I found an article in the database saying MS was aware of the problem and finally got that to work (KB885222) download

  http://download.Microsoft.com/download/9/0/6/906f2f67-39c4-48bc-8558-86833d4cbc16/WindowsXP-KB885222-v2-x86-enu.exe

  It will not actually install on the PC I am running SP3 not SP2.  It's really frustrating because the system worked very well under windows 2000. Even worse since I have a lot of old video - not stored on DVD or transformed into films which I was hoping to work for presents for the family, this Christmas.

  Anyone know of another - hotfix - download or similar which will fix this problem?

  Hi John,.

  Thanks for posting in the Microsoft Community Forums. I suggest you post this question in this forum for better support.

  http://social.technet.Microsoft.com/forums/en-us/category/windowsxpitpro

• Remove devices multiple adapter remote Microsoft Windows Mobile or Windows Mobile Device Center of difficulty

  I currently have 244 devices with Microsoft Windows Mobile adapter hidden, not connected, listed in Device Manager in Windows Vista. Windows Mobile Device Center stops working correctly when the device name is Microsoft Windows Mobile Remote adapter #243 or higher. Y at - it a fix for Windows Mobile Device Center, or a way to easily remove all 244 cards at the same time?

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. Appropriate in the MSDN forum.
  http://social.msdn.Microsoft.com/forums/en-us/categories/

• F5D5050 USB 10/100 Ethernet adapter Belkin for Windows 7

  I have windows 7 and I checked the comparability on the Microsoft Web site and it says that the F5D5050 USB 10/100 Ethernet Adapter is compatible but when I plug it in, I get an error message that the Broadcom Bluetooth 2.1 + EDR USB device has a driver problem.

  Anyone had luck to get this product to work on windows? Does anyone have an idea how to operate?

  It was the procedure to install it on Vista http://www.belkin.com/support/article/?lid=en&pid=F5D5050&aid=4404&scid=220

  It does not have Windows 7 drivers and looks like it is be misidentified.

  You can get more help on the Windows 7 forum.

• Win7x64 with adapter DWA-160, "Windows could not automatically bind the IP protocol for the network card stack."

  As the title suggests, I am running Windows 7 family, 64 bit. This is a new installation, a few days ago and I have not installed anything on, or changed the settings.

  I installed a DWA-160 D-link Wireless adapter n with the current drivers, fix (before you ask to confirm, they come from Web site of D - link. I used initially the disk included in the box, however, this has generated the same question that I'll explain, so I uninstalled this software and has continued to use the Windows program to connect to the wireless network.

  I can connect to the network, of course; However, I get the message "Windows could not automatically bind the Protocol IP on the network card stack" when connecting each time.

  After searching for an answer, I tried to turn on the WLAN auto configuration service, however, it is enabled by default. If this isn't any help.

  Tried the netsh winsock / netsh int ip / netsh int ipv4 / netsh int ipv6 reset and restarted after each, no change, if this isn't any help.

  Made sure the problem wasn't with the wireless router, and it isn't because I can connect with my laptop.

  Tried to plug in the USB stick on another computer yet. I don't want to plug into my laptop just to test that possibility. So. Yes.

  I also don't know much about all the inner workings of one of these things, so it would be rad If everything was in one step by step. Thanks in advance.

  Try to run This Fix - It.

• NET: ERR_Cert_Date_Invalid - Windows 7

  Separated from this thread.

  Operating system: win 7 home
  URL (if applicable):
  Error message: NET::ERR_CERT_DATE_INVALID
  Installed extensions:

  Hello, Anshunandeshwar,

  Welcome to the Microsoft community.

  You had posted a thread to Windows XP.  Having the certificate on a Windows 7 system error?

  What browser do you use?

  Internet Explorer users:

  1. Under the tab Security in the Internet Properties dialog box, select the Local intranet zone, and then click Sites.
  2. In the Local intranet dialog box, click Advanced.
  3. Clear the requires a secure server (https :) for all sites in this zone check.)

• Impossible to use the adapter EasyCap on Windows 7

  Original title: EasyCAP help :(

  Hello, I recently bought an EasyCAP wishing to record Xbox game, however I bought all the extras needed to have my Xbox display on my tv and a laptop, but I can't make it work :/ I installed several recording software compatible with the EasyCAP but none of them link to design it and say things like 'No signal detected' ect, my computer picks up my Xbox on the add a section of the aircraft, but could not install a driver and I was unable to find a :/ I have a laptop windows 7 64 bit and really need help I tried day and don't know what to do :/ Any suggestions or advice would be really appreciated

  ~ Thank you Lauren

  Hello Lauren,

  Microsoft has no any information relating to the compatibility of the EasyCap adapter on Windows 7 operating system.

  Please help me with the following information related to this issue:

  1. other USB devices work end on your computer?

  2 have you tried to connect the EasyCap adapter on another USB port?

  3. have you checked whether EasyCap adapter works on another computer with a different operating system installed on it?

  I suggest that refer you to the steps in the following link and check.

  Automatically get recommended drivers and updates for your hardware

  http://Windows.Microsoft.com/en-us/Windows7/automatically-get-recommended-drivers-and-updates-for-your-hardware

  Please answer us on the State of the question as well as the information required to help you further.

• MS ISATAP Adapter # 2 in Windows 7 driver problem

  MS ISATAP Adapter, MS ISATAP problem adjust # 2 Driver and driver MS Teredo Tunneling problems which could not be fixed automatically by the software.

  Hello

  Don't you worry about this unless you have found errors. If so see these threads.

  http://social.answers.Microsoft.com/forums/en/w7network/thread/754c8f29-3a87-4E77-Babd-a69c8910e17e

  http://social.answers.Microsoft.com/forums/en-us/w7hardware/thread/05a8849e-89c1-4CC9-8004-f6d07a4fdf8b

  http://www.cableforum.co.UK/Board/34932105-post6.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• How do you completely disable the Adaptive brightness on Windows 8?

  I have a Thinkpad x120e; upgrade to Windows 8 last week and we tried EVERYTHING to get rid of this brightness Adaptive craptastic.

  The screen becomes clearer on a white background and fades slowly on the dark images. I feel like I'm tripping when I read the articles online.

  Yes, I turned the Adaptive brightness (battery and AC options). Yes, I tried each power plan. Yes, I created my own power management, through the Lenovo "power manager" and "Control panel" window. Yes, I optimized the display, I updated the driver for the monitor. I did everything. Even spent an hour chatting with Microsoft technical support (who says essentially nothing is false and restart my laptop). I swear to you that this thing is to go out the window if I have to deal with the darn labile brightness.

  Please help me. Please, please, please and thank you.

  golightly716

  So I don't know anything about your computer... and I don't know if you still have problems.  I had the same problem, my computer would be dim whenever I'd go for a darker picture.  I was getting so frustrated with no solution anywhere.

  Finally, I found the answer for me was to to in the media parameters and an Intel Graphics. Turned on, there is a setting for a battery.  Which has been set to display Power Saving Technology.  I just décliqués who and now my computer decreases more.
  It's amazing all the places on the Windows that controls a power and a brightness adjustment.  I found this after days and days of research.