Add WAP300N to EA4500?

Similar Questions

• EA4500 and OJ8600 of HP printer router interface questions all in one.

  Hello I am running IE11, WIN8.1, 1 TB HD, 12 GB of memory with EA4500 router from Linksys connected to the computer via an Ethernet cable.  The computer is a Lenovo desktop (K430). I ran a test installation of HP troubleshooting on the interface between the computer and EA4500.  I opened my Linksys Smart Wi - FI to perform the following two tasks. The HP Installation troubleshoot suggested I should put MAC address filtering to off I did without any problems. Installation troubleshooting HP also suggested I have find the MAC address of my printer and add it to my list of devices that are allowed to access my networh. How can I do this? Thank you.

  You should make a print from the printer setup page and who should detail you information on MAC and IP addressing. I recommend not to use Mac filtering because it is not necessary. I recommend that you configure a static IP address ON the printer, 192.168.1.86, that should be the default value of routers outside main pool DHCP de.100 thru.199. You will need to refer with the Lim and information on how to establish networks and set up the printer. Consult the user manual as well.

• New firmware, new problems with EA4500

  I logged this morning to a new firmware on my EA4500. I have disabled the automatic upgrades when I got the device because at the time of the hidden networks was not supported by the firmware of the Wi - Fi chip. Needless to say I was shocked when I logged in this morning. I have no idea how the new firmware had updates since I was the only one on our staff with the password on this device.

  However, I went in the new admin panel MAC filtering section and tried to add a new device to our list. I get "Unexpected error" 2177 when you try to save the updated list.

  Show details: / jnap, macfilter, SetMACFilterSettings - status: 200 OK Date: Tuesday, August 7, 2012 06:01:59 GMT Server: lighttpd/1.4.34 connection: close Content-Length: 42 Content-Type: application/json; charset = utf-8

  I can't go past this screen to save the MAC address on the list of filters. Any ideas? Current firmware is 2.1.41.162351

  Try the Revert to previous FW?

  Safely update FW, I recommend doing the following:
  1 save the router config to the file first using IE or FF with all modules disabled security.
  2 factory reset the router with all devices disconnected or turned off accept for 1 Wired PC.
  3 reload or update the FW using IE or FF. Just download the FW file to your wired local LAN PC.
  4 factory reset the router and then set up from zero all first and test with loading saved configuration from the file. Check if problems are solved before loading the saved configuration file.

• Maximum number of EA4500 of port

  Hi all

  Background: currently have a WRT320N, think about upgrading to an EA4500, assuming a feature has been improved: Port Forwarding.

  Script: Currently, I have a router WRT320N, and while he "does everything we need" it presents a restriction that comes in the way: limits on the number of ports address.  In the Panel of port forwarding, it has 15 total lines: the first five lines can be activated for specifically named services (SMTP, FTP, etc.).  The last 10 lines are fully customizable in that we can define the name, port and Protocol.

  The problem is that 13 total ports that currently, I need to pass, only one is listed in the fixed list.  So, unfortunately, I can only use one of these first five rows.  I have completed ten custom lines and still need two additional ports (for now, may need down the road).

  Try to be creative, I thought maybe I could just more reverses the Port Range Forwarding page and add a line or two.  The only problem: it's bugged.  I found that if the simple Port Forwarding list is filled, then the Port Range Forwarding entries do not work properly.  For example, if I wanted to port 12345 and 12346 forwarded to 192.168.1.5, they work very well with two entries in the single port forwarding.  However, if I delete those, add two lines of port that I need has passed (the single list is new) and add a port forwarding 12345.12346 range, they do not work properly, only ports are closed. The work of singles, the beaches don't.

  Question: The EA4500 has solved this problem and either allow more lines (i.e. 20 customizable inputs instead of 10), or, better, does it just a button [Add entry] to allow additional lines to create?  In the current day and age, where a single device (for example an Xbox) can take four lines, a limit of 10 lines is quite sparse.  Comparing it to some competitors, for example the D - Link DIR-825 (aging, but still a lot) allows you to add as many as you want.

  I realize 'expensive' firewall SonicWall have virtually unlimited customization, but I not need many additional features and don't want to spend $ 350 on a "high-end" firewall to solve the problem you need more ports open.

  Thanks for any help you can give!

  -Dan

  I can't speak for the ea4500, but on my e4200v2 I 15 customizable ranks in more the 5 rows together:

  

  As the e4200v2 and the ea4500 are essentially the same from what I've read, I imagine that the ea4500 will have the same thing.

• EA4500 - a wireless device of many with internet connectivity problem

  Hello

  I wonder if anyone can comment on a subject that I have with a (a) wireless on my home network devices.  The problem is that a Dell laptop knows slow or no internet connectivity using wireless at all.  Sometimes 1-2 minutes to load one page, other times the message 'not able to display the Web page' dreaded.  That's using Ethernet.  I have another laptop (brand/model exact even) and it has no problem.  I also have a Macbook Pro and other IOS from Apple (iPod/iPad) devices which are very good.  Several connected Ethernet devices are very good as well.  The laptop in question had no problem with my previoius Linksys devices, which are a BEFSR41/WAP55AG and a WRT-54GS v2.  This laptop was the first day or two on the EA4500, but something happened that causes this problem.  I had to add the WAP55AG on my network so my son is happy again, but my plan was to dismantle the other devices.  Suggestions regarding what I can do to fix this are greatly appreciated.

  Thank you.

  EA4500 Firmware v.2.0.37

  Laptop Dell Inspiron 15 w/Intel Centrino Wireless N1030, 1 x 2 bgn (2.4 GHz) + Bluetooth

  Hello

  Thanks for the suggestion.  I tired who, but it did not work.  I then called Dell and they found that the wireless adapter on battery power has been set to maximum power saving.  Changed for maximum Performance and it's been very well.  Fortunately there is nothing wrong with the router.  Thanks again for the suggestion.

• QoS EA4500

  I bought the EA45500 specifically to configure QoS on specific devices by MAC address.  I would like to give preference to the PS3 for online games.  The first time I went to the QoS to the interface of the browser tab, I could start to put in the settings, then after the second or third recorded, the QoS tab has nothing of my settings and accept all the entries or save the settings (see image inserted here)

  

  I now notice that as soon as I put on the EA4500, he had the v2.0.36.126507 firmware.  During the installation (before the QoS setting), I tried (without success) load new firmware that has been identified.  Today, I see that the new firmware is loaded v2.0.37.131047.

  Anyone can shed some light on this?  Can I restore the firmware manually? If Yes, where can I find it?

  

  Thank you hiptechboy.  Factory setting reset indeed QoS page, so it was functional, however, I learned a little more I started to restore the configuration.  Given that I had saved configuration settings at various times during the initial installation, I restored it with the last save point which included the 'bad' QoS and the QoS page was in fact still bad. So everything he does gets saved to the backup / restore configuration file.

  As I said, I had several backups, so I took one earlier (before the adjustment of QoS page).  This restoration has a functional QoS page after restoring the configuration. So, I added my first priority QoS settings on QoS page and saved a backup of the configuration.  I added the second priority QoS, recorded on the page of the QoS parameters and save a configuration to the top.  When I added the third QoS parameter and registered on the page of QoS, all my settings have disappeared and the page was more functional.  I must have got the third entry of the QoS the other night, when he 'stop working '.

  This time, I have simply restored from the last save point and again had a functional QoS page.

  

  So I guess that the quality of service is limited to 2 items.  Add a third and once settings makes this useless page and as I said, it is recorded like this in the configuration backup.  I would like to put the iPod Touch, iPhone and iPad on a lower priority for streaming video is not interfering with the online game of the PS3 (i.e. CoD MW3).

• I have an ipod touch 128 GB... but I'm almost to reach its maximum.  I want to do is buy a new ipod touch 128 GB and add new music without synchronizing the entire library to it... I have 2 ipods in conjunction with other copies

  I have an ipod touch 128 GB... but I'm almost to reach its maximum.

  I want to do is buy a new ipod touch 128 GB and add new music without synchronizing the entire library to it... I have 2 ipods in conjunction with the other copies of the other.

  is this possible?

  What should I do?

  Matt

  When you get the new iPod, you can use iTunes on your computer to select and synchronize the music you want on it, in the same way that you synchronize your current iPod - your iTunes will recognize them as different devices and will remember your choice of synchronization for each, it will not (unless, for example, you restore the backup of your current on her iPod) put the same content on both.

  (I asked for your post be moved to the iPod Touch forum, where you have posted is the iPad forum use.)

• The screen add people faces a (~ 1600) much just show as squares of white, grey

  Hello

  I was going through my photo library (running 2.0 on Sierra Photos) cleaning and marking of the people. I got far just about every face on the left is a square white, gray. If I add this person, the area where the image would be just rotates the circle of progress.

  Any idea on what is happening? I really miss the ability in iPhoto in order to have a Smart Album based on a photograph with a person "without name".

  Thank you, Tim

  

  That is a disused here bug that if you click on the x to remove a face, you end up with a tile empty - I hope that this will be fixed in a future Apple 9tell on the bug to improve its priority - http://www.apple.com/feedback/photos.html of output) and I hope that the patch will fix these old problems as well as properly - not advancing It is better to stop the removal of the faces until this problem is corrected

  LN

• Add dictionary

  Hello.

  I have a question: I would like to add additional dictionaries in the Sierra of MacOS.

  Initially, some trouble with record find "dictionaries". But this problem is solved here: where is the dictionary in the Sierra folder

  After that, I saw:

  

  (It seems different from El Capitan).

  In the folder "CoreDataUbiquitySupport" can't get the files with the .dictionary extension.  And throughout the system (I used Spotlight) I cannot find these files.

  When I try to add my files with extension .dictionary in "Dictionaries" folder - nothing happened.

  Please, help me. What should I do?

  Thank you.

  I found the files .dictionary you are looking for here:

  / System/Library/assets/com_apple_MobileAsset_DictionaryServices_dictionaryOSX/37 7ca105ade0203e0c89af6538f7b8ab0204dfba.asset/AssetData/Oxford English.dictionary thesaurus

  / System/Library/assets/com_apple_MobileAsset_DictionaryServices_dictionaryOSX/5 has a689bfd471f943f70bd220ec2ed3849b7dbec3.asset/AssetData/Oxford Dictionary of English.dictionary

  / System/Library/assets/com_apple_MobileAsset_DictionaryServices_dictionaryOSX/f9 384c21fc7d64ad09992ad8bebbbfac16ad6a9d.asset/AssetData/Apple dictionary

• can I still add to apple care if the warranty has expired?

  can I still add to apple care if the warranty has expired?

  No, if it is out of warranty, if it is for a Mac: http://www.apple.com/support/products/mac.html

  The AppleCare Protection Plan can be purchased as long as your Mac is still covered by the limited warranty of one year.

• Add people

  So, I've updated for Mac OS Sierra. Have been using the Photos app since it was released and spent a lot of time organize using faces and now I have hundreds of photos to browse again and put names to people.

  I'm in add people and get 632 white picture with numbers under. To be able to identify the people, if I add them, and then double-click it to view more deep - no images do not face appear.

  I already went through and added all the images of virgins like that and then hidden, now, today, I have another more than 600 of them. Any ideas?

  I NSB Sierra since the evening he lauched and use my Mac every day for that if he should have had time to complete the analysis now.

  Thanks & Hello all

  

  but he has finished scanning and - when you launch Photos and click on people get you people or a text for scanning status?

  LN

• "Add a printer" crashing

  Pref systems > Scan & print

  I can open the Scan & Print window under system preferences; However, when I click (+) to add a new printer, the Add Printer dialog box opens a second and quits immediately. This behavior started after I removed an existing printer.

  Does anyone know how can I fix?

  Reset did not help.

  Error log shows:

  Process: AddPrinter [406]

  Path: /System/Library/CoreServices/AddPrinter.app/Contents/MacOS/AddPrinter

  ID: com.apple.print.add

  Version: 8.3 (405.2)

  Generation information: PrintCenter-405002000000000 ~ 1

  Code type: X 86-64 (Native)

  Parent process: launchd [177]

  User ID: 501

  Date/time: 2016-10-05 16:30:40.801-0700

  OS version: Mac OS X 10.8.5 (12F2560)

  Report Version: 10

  Crashed thread: 0 dispatch queue: com.apple.main - wire

  Exception type: EXC_BAD_ACCESS (SIGSEGV)

  Exception codes: KERN_INVALID_ADDRESS at 0x000000010e05ca8f

  Reset the printing system

• Why can't add sounds to mail to Sierra

  After the upgrade to Sierra, I would add is no longer a 'personal' sound of my files to act as my 'new message '. The sound folder is locked and I have, even as an administrator, can't unlock it or add sounds in the folder.  All I have now is a drop-down list of predetermined choice of Apple, and none of these things include the addition of new sounds.  Preference once gave me the choice to go to my files, I have more choice. Can someone tell me how to add my own sounds?

  MACBOOK PRO15.

  Intel core i7 to 2.7 GHz

  8 GB memory

  as it is in this matter and, of course MAC OS Sierra 10.12.

  Greetings gklav,

  Thank you for using communities of Apple Support. It seems that you want to use a custom sound in Mail when a new message arrives. I recommend reading this article, it explains how the feature works and what is available.
  
  

  New sound of messages

  The sound to play when you receive messages. To make a sound sampling, click on the context menu, and then select a sound.

  Mail for Mac: General preferences in Mail

  Take care.

• When I add a playlist to my library, it automatically updated with new songs?

  Hello world

  When I add a playlist to my library, for example a list of music playback from Apple which is regularly updated by the editors ("Best of the Week" or 'Hits of today', for example), did the playlist in my library automatically update with new songs, when new songs are added?

  Thank you in advance.

  Hello, take a look at this article If you see not your entire library after you update iTunes on your Mac or PC - Apple Support

• Tips to add a VPN router to my current network configuration

  Dear all

  My apologies if the answer to this question already exists, however, I searched in many situations and none seem to match what I'm after.

  I currently have an ISP modem/router in Bridge mode connected to a TC of Apple which is my wireless router, I have 2 Express airport connected to this acting as the extensors of the range.  I have a VPN service through the MyPrivate network I activate on the desired device when required and everything works fine.

  What I want to do now is to be able to use my AppleTV and burning Amazon via the VPN as well so you need to add a VPN router in the configuration.  I want to finish with 2 wireless networks running together for these devices who need VPN and those who are not.  I don't want to lose the opportunity to extend the network to express it however airport.

  If someone could explain to me if this is possible and if so how do I set up the network.

  Thanks in advance

  Mark

  Basically you would need a device that supports VPN-passthrough and VLANS for your goals of networking. MyPrivate network, seems to be a VPN SSL, which is a user-server configuration. In other words, you install a client VPN on your Mac and you connect to the VPN network MyPrivate server to establish a VPN tunnel.

  Networking two or more "separated", should be using a router that supports VLAN services. Each segment of VIRTUAL local area network, in essence, would be a separate, she either wired or wireless network or a combination of both. This would probably be the 'easiest' part for the installation program.

  Now how combining the two would be the question, and I don't know what would be the best way, or even if it is possible.

  A few thoughts:

  • Use a router that supports VLANS. Create at least two VIRTUAL LAN segments. One for Apple TV & Burns, one for Internet access in general. Connect the device to VPN client host on the first segment, and configure for Internet sharing.
  • Download a dedicated VPN network application that supports hosting of third-party VPN clients, like yours. You would still need a router that supports VLAN to provided separate network segments.
  • Hire a consultant network. Let them know what you the goals of networking and ask them to offer potential solutions.