Address of Flex M1000e

Similar Questions

• License restrictions impede access to this address.

  After the CF7 updated to the new DST requirements, we are seeing INTERMITTENT problems with some being not loaded SWF movies.
  
  Flash forms work fine.
  Any indication to examine how would be fabulous.
  
  ColdFusion - err.log shows:
  03/13 15:47:48 Proxy Servlet ERROR: license restrictions prevent xx.xx.xx.xxx access
  03/13 15:47:48 ERROR Proxy Servlet: authorized addresses: [{71.218.19.250} {192.168.1.145} {74.93.23.77} {24.131.24.127} {192.168.1.1}]
  03/13 15:47:48 error Licensing restrictions prevent access to this address.
  java.io.IOException: license restrictions impede access to this address.
  at flex.services.license.AddressRestrictionFilter.invoke(AddressRestrictionFilter.java:28)
  at flex.server.j2ee.cache.CacheFilter.doFilter(CacheFilter.java:165)
  at flex.bootstrap.BootstrapFilter.doFilter(BootstrapFilter.java:66)
  at jrun.servlet.FilterChain.doFilter(FilterChain.java:94)
  at jrun.servlet.FilterChain.service(FilterChain.java:101)
  at jrun.servlet.ServletInvoker.invoke(ServletInvoker.java:91)
  at jrun.servlet.JRunInvokerChain.invokeNext(JRunInvokerChain.java:42)
  at jrun.servlet.JRunRequestDispatcher.invoke(JRunRequestDispatcher.java:257)
  at jrun.servlet.ServletEngineService.dispatch(ServletEngineService.java:541)
  at jrun.servlet.jrpp.JRunProxyService.invokeRunnable(JRunProxyService.java:204)
  to jrunx.scheduler.ThreadPool$ DownstreamMetrics.invokeRunnable (ThreadPool.java:318)
  to jrunx.scheduler.ThreadPool$ ThreadThrottle.invokeRunnable (ThreadPool.java:426)
  to jrunx.scheduler.ThreadPool$ UpstreamMetrics.invokeRunnable (ThreadPool.java:264)
  at jrunx.scheduler.WorkerThread.run(WorkerThread.java:66)

  It is not a J2EE installation. It is installed standalone on IIS6.
  Anyway, Jrun is ultimately rejected deploy cfusion on the launch of the service.
  I completely reinstalled the full install of CFMX.

  Thanks anyway.

• Flex publish / subscribe does not public IP address

  I installed the last Flex Express LCD on top of ColdFusion 8 enterprise demo installed as JRUN/multiserver and got it all to work when you run directly from the server using the "' http://127.0.0.1:8300 / samples". " However, when I run outside with public IP address of the server, then everything works except for samples of publsh/membership push. They just hang and impossible to subscribe. Any ideas? What is a restriction on the LSCDS Express or the CF8 demo version? Or maybe a port problem? We have all ports closed except for those needed. There is an additional port that is to be opened in addition to 8300? Thanks for any help.

  I think I found the problem. It seems you must have port 2037 open for RTMP to work e-mail with sample apps. This port is closed on our firewall and I suspect that's why I'm having a problem. I'll get my network guy to make the change on Monday and then I'll try it again. Probably that it will solve.

• Requirements of the M1000e IP address?

  I'm working to implement the M1000e chassis using 2 blades Dell Force10 MXL integrated switch. between the swtches built and other management functions, the number of IPS do I need to allocate to the chassis?

  Hello

  Probably at least three, one for each of the MXLs and one for the MCC. You can also IPs for each of the iDRAC on the blades, so that you can access it directly.

• How do I make the smaller address bar so I can get all my favorites next to her, thus avoiding the need for the bookmarks toolbar?

  As the title suggests, would like to have more space for my beloved booksmarks. A bit how you can do the "search bar" more great compared to the address bar.
  Feel free to ask away if I did not myself clear. We hope to get help quickly. BTW, like the browser.

  You can try adding this code in the userChrome.css file.

  • [1043584/questions/1043584] Problems with showing bookmarks toolbar items / Rendering

  Add code to the file userChrome.css below default @namespace.

  • http://KB.mozillazine.org/userChrome.CSS

  @namespace url("http://www.mozilla.org/keymaster/gatekeeper/there.is.only.xul"); /* only needed once */
  
  #nav-bar-customization-target > #personal-bookmarks {-moz-box-flex:1!important;}
  

  The file userChrome.css (UI) customization and userContent.css (Web sites) are located in the folder of chrome in the Firefox profile folder.

  • http://KB.mozillazine.org/Editing_configuration

• I want the address bar so that my bookmark bar can show more than three icons when it is placed on the same line.

  I have about five to ten icons bookmark in the same line as the search and address bar. So I use customize... and I put the bookmarks on the same line bar. I leave the "name"-textbox in each bookmark in white so that only the icons. ""

  However, only two icons appear and the rest are displayed in a drop-down list with an arrow you click.

  I need not address bar to take 70% of the screen. I don't want the bookmarks bar to use an additional line. I just want to have the icons of bookmark five to ten next to my search and address bar. Is this possible?

  The address bar and the search bar, that both have a flex attribute that makes then take all available space.
  
  Items in Bookmarks Toolbar folder probably has a minimum width that can just make a bookmark with a maximum length label (in your case two icons).

  You can set the width of the address bar and the search bar to force a maximum width of these two bars max.
  Definition of a minimum width for the bookmarks toolbar items will probably work as well.

  Add code to the file userChrome.css below default @namespace (setting the width according to your needs).

  • http://KB.mozillazine.org/userChrome.CSS

  Customization files (interface) userChrome.css and userContent.css (Web sites) are located in the chrome folder in the user profile folder.

  • http://KB.mozillazine.org/Editing_configuration

  @namespace url("http://www.mozilla.org/keymaster/gatekeeper/there.is.only.xul"); /* only needed once */
  
  #urlbar-container { max-width: 400px !important; }
  #search-container { max-width: 200px !important; }
  

  You can use this code to set a minimum width for bookmarks toolbar items if you want to experiment with that.
  
  You may need to set a width max as well.

  #personal-bookmarks { min-width: 200px !important; }

• Flex 15 fan does not

  I just bought a refurbished Lenovo taking Flex 15 and it does not appear that the fan is running. I transferred some pictures on the HARD drive and it got extremely hot, but the fan never came. I read in another post that update the BIOS might help, but the Flex 15 driver/support download page does not load.

  http://support.Lenovo.com/us/en/products/laptops-and-netbooks/Flex-series/IdeaPad-Flex-15-notebook

  I get this message:

  The document you requested is not available. You may have entered an incorrect URL or connect with credentials allowed (for Lenovo field Servicers and/or Call Center Agents only) to display the page.

  • For drivers, please click here
  • For user manuals, please click here
  • For the resolution of problems and Solutions, please click here
  • For warranty information, please click here

  If you want to ask for more information, please submit an immediate feedback by clicking on [+]. Please indicate the subject of the document and your e-mail address for a response.

  Can you please send me a link to the BIOS update file or instruct me on how to test the fan.

  Thank you

  -Nolan

  In fact, I got the fan works for someone who cares. There was a slight clicking sound coming from the it. (click, click, click on...) I turned the laptop on the side (running) for about 30 seconds and started the fan turning. Not sure if something he obstructs or if dust is causing, but it works now. I bought a new fan of ebay, just in case it stops working again. I cross my fingers.

• HP 4156 Analyzer b - Flex control

  Hello together

  I am very new to Labview so I have a lot of questions

  Does anyone have an example of using the flex command in a Labview VI? I have HP programmers Guide, but an example of work would help me to program my own VI.

  Thank you

  First of all, identify what type of communication you have wih your device. for example, GPIB, USB, etc. series.

  If GPIB is the right way, you can use the Explorer measurement & automation to find the GPIB address (if you do not know).

  Then go to "Examples" in Labview and see examples of communication GPIB, LabView has builtin. This will help you to send commands and receive responses from the instrument. If more detailed control is needed, you might end up creating a more advanced VI which can define the instrument with the parameters you set, and then read the results.

  Another way to get around this is to find the LabView instrument drivers where most of the time, it contains an example of sorts for the communication of the device.

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• M1000e with M8024 (problem connecting to pass)

  I have a Dell Poweredge M1000E Blade chassis with two switches of the M8024.

  I configured the IP addresses of the M8024 (B1 and B2) on the CMC web.

  All ports on the controllers of chassis are connected to my network.

  I can connect without problems to the M8024 into the slot in B2, but cannot connect / ping / access the M8024 in B1.  I have tried power cycling/replace the switch but no luck.

  Any suggestions?  I tried not to do anything via a SERIAL connection.

  I understand the problem!

  CMC M1000e chassis preview / network / config VLAN.  The VLAN Tag parameter has been activated for the M8024 in B1.  This prevented work properly on our network, because the vlan defined for the specified VLAN ID was not set up.  I unchecked the box in the column "Enable" (for B1) and he now available!

  Thank you!

• customers on flexconnect AP cannot get dhcp address after upgrade wlc

  Hi community support.

  I have a WLC 2504, with 30 APs 1130 flexconnect mode. The WLC runs the code version 7.0.240.0. In order to register new models of ap, we need upgrade to a recent code.

  In the last attempt to upgrade to version 7.4.121.0, the AP has joined the WLC, mappings of vlan in flexconnect have been checked and were very good. However, customers were unable to get an address DHCP (169.254.x.x). The DHCP server is local to each location, is usually a 3750 x that serves as a master switch.

  connection via cable, clients received address dhcp. so the dhcp server isn't the problem. Updated for the 7.6.100.0 code, but got the same behavior.

  Finally, we decided to downgrade the wlc code 7.0.240.0 once again, and everything started working again, but I need upgrade we buy access to new models of points.

  Someone else had a similar problem?

  Thank you

  Hello

  What is the vlan native you are using? If it's the number of vlan 2, then it is known bug CSCui73764

  Symptom:

  Flex series APs 1130 & 1240 mode, won't see traffic, for example, DHCP, ARP. on some wireless LANs.

  Conditions:
  (1) flex connect local switching
  (2) AP 1240 or 1130
  (3) any version before 7.4.121.7
  (4) native vlan x, not work y vlan.
  (5) failed to get the ip address of the user.

  Workaround solution:
  change the vlan native to a surprisingly high number, so no wlan will never be are mapped to a very high bridge group number.

  Other Description of the problem:
  Telnet on the flex AP. here is an example. VLAN 3 is the vlan native Flex ap, it is correctly mapped to group 1. now WiFi is not working is the one that is mapped to vlan2. below, carefully, the vlan 2 is mapped to fill the 3 group. It is the forum where we hit the bug. Therefore, it can be any combination of wlan-vlan-native vlan.

  HTH

  Rasika

  Pls note all useful responses *.

• Flex in 90-minute tutorial

  Hey guys. I've been playing with flex in tutorial 90 minutes because the way it's Setup is what is best for my next app. I modified it to provision differently, and it has worked flawlessly. There are, however, two problems I have.

  The first problem, when I deploy on the desktop, everything works fine. It loads up to the main screen, click on a search button I put in place, then past in the search screen, I type in a Word, the element appears on the list and I can click on it to move to the next screen. But, when I deploy in the Simulator, I go as far as the search screen and cannot go any further. When I type in a Word and click on the search button, nothing happens. Why would this work in the office but not in the Simulator?

  The other problem is that I can't seem to change the text of the .xml file. In the .xml file, all employees are listed with different information such as position, email addresses, phone numbers etc. Now when I try to change this information, the old information still show when the application runs. I thought the app pulled data from the .xml file directly? There is no errors or warnings that appeared in Burrito.

  Any thoughts?

  FIRST QUESTION: this 90 minute demo comes out with the SDK 0.9.2 now SDK 1.0.1 is very different from that, so you need to add access_shared in the blackberry - tablet.xml leave is working, or update the code to avoid the permission of "access_shared".

  SECOND QUESTION: I remember. the XML is loaded into the sqlite database at the spearhead of the demo in the first, after it, app will affect not the xml file more, update the contents of the xml files you want and rename the database in another name, therefore, faster solution.

  Good luck.

• HP BL490C G6 / NC553M / Virtual Connect Flex-10 / frames not subproject

  Hello world

  So, we are adding some additional 5.5 ESXi hosts in our cluster.  Host hardware configuration looks like this:

  * BL490C G6

  * Dual Proc

  * 72-144 GB of RAM

  * Integrated NC531i NIC

  * Other NC553M NIC

  Inside the enclosure, we have four Flex-10 modules to provide connectivity to the NETWORK adapter as well as the NIC NC553M to the location of mezz 1.  The reason for the card NETWORK NC553M is it is supported of the extended 9K frames.  The NC531i has only 4K support frame.  It's the exact configuration for a G6 blade in the HP cookbook on page 10 of the http://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-c02533991-10.pdf

  On the side of Virtual Connect I have four modules stacked with cables SFP - DAC 10 m 1 GB to provide connectivity and then we have a shared connection fixed module 1 and module 2 for the power switch in this cage to 10 GB so.  On the kernel to miss, we made sure to allow frames jumbo on iSCSI VLANS.

  I made sure my vSwitch and adapter MTU are all set to 9000.

  

  

  

  The problem is that I can not vmkping with everything above a size of the iSCSI standard package VLAN without having too much attention when I say do not fragment.  As you can see from downstairs than a normal ping works fine, but if I try something like a 2K ping fails.

  

  The switch that he speaks is HP Procurve 5400ZL R2.  I configured a port of 1 GB on the untagged for the iSCSI switch VLAN and I had no problem by assigning an IP address of my computer windows laptop, allowing 9 K jumbo frames and the realization of pings jumbo frame network SAN.  So, that tells me that the switch on the side of SAN seems good.

  So what in the world could cause this problem?  Some things roll around in my head are:

  • Configure another blade of VMWare inside the chassis configured the same way as this one.  See if I can vmkping of frames to the other blades VMWare iSCSI NIC if it works then it would tell me that jumbo frames work inside VMWare and inside the virtual environment itself connect C7000.  They swear in all Virtual Connect documentation that frames "turned on by default".  I would like to find a way to confirm that on the CLI or something.
  • Configure a dedicated connection for iSCSI traffic on the Flex-10 modules to iSCSI VLANS.  Do not use a shared set of uplink.  This shouldn't be a problem though.  This is the scenario 2 of the HP Virtual Connect iSCSI Cookbook
  • Configure another slide with the same material, but something as CentOS load on it and see if he can make this map jumbo frames and the network.  If it can and can not VMWare then he would tell me something wrong with my configuration of VMWare

  I would really appreciate anyone who helps to solve this problem of configuration.  We really need get this cluster running inside this frame so that we can continue with a migration project.

  Sincerely,

  Jonathan

  I have seen that sometimes a host needs a real reboot after enabling jumbo frames, did you do that?

  'Too long message' error comes from the IP stack own hosts and not a peripheral network between the two, your package is never leaving the host.

  Make sure to specify the interface vmkernel dating the -I spend when you run vmkping:

  1. you can vmkping the host on his own localhost and vmkernel interface IP? For example:

  # vmkping d s 8972 127.0.0.1

  # vmkping - I vmk1 d s 2000 [Destination IP]

  2. try tests with esxcli network, diag ping utility for example:

  # esxcli network of diag ping - df - vmk1 - the ipv4 interface - size 2000 - host [IP of Destination]

  3. your iSCSI network is on a completely different subnet of all other interfaces vmkernel (e.g. Management), and it is a flat area not routed layer 2, right?

  4. always make sure that your card drivers NETWORK and firmware are up to date.

  5. the output of the following commands could be useful as well, if you replace information such as IPs please do so in a consistent way to keep relationships intact:

  List of the nic # esxcli network

  # esxcli network ip interface list

  get # esxcli ip interface ipv4 network

  list of ipv4 route # esxcli ip network

  vmware # esxcli network vswitch dvs list

  list standard # esxcli vswitch network

  List of the nic # esxcli network | awk (' print $1' "). grep vmnic | while reading nic; make esxcli network nic get - n '$nic '; fact

  # vmware - v

• 4.6 AIR 19 iOS Flex 9 ADT package fail: library not found for - ISystem.B

  Immediately after the upgrade to Xcode 7 and try to debug my Flex AIR project, it does not package for iOS. This occurs when you try to debug on the device (iPad 2 iOS 9). Attention of:

  
  

  ---------------------------------------

  Create iOS package

  ID: library not found for - ISystem.B

  ID: library not found for - Igcc_s.1

  Compilation failed during execution: Id64

  …

  ---------------------------------------

  The two Adobe Flex superimposed 4.6.0 with AIR 18.0.0.199 and Adobe Flex superimposed 4.6.0 with AIR 19.0.0.193 fail with the same error.

  In addition, debugging in the Simulator, we get another warning at startup:

  ---------------------------------------

  Launch of iOS app

  [MT] DVTAssertions: Warning in /Library/Caches/com.apple.xbs/Sources/DVTFrameworks/DVTFrameworks-8201/DVTFoundation/Plug InArchitecture/PlugInManager/DVTPlugInManager.m:257

  Details: Asked but can't find extension point with the identifier Xcode.DVTFoundation.DevicePlatformMapping

  Object:

  Method:-extensionPointWithIdentifier:

  Discussion: {number = 1, name = hand}

  Please fill a bug report at http://bugreport.Apple.com with this warning message, any useful information you can provide.

  ---------------------------------------

  
  

  The first defect is really the block. I can't usefully working on the project until this is addressed. No difficulty in suggestions welcomed, TIA.

  Please follow the following to workaround [Applicable only for MAC]

  1. download and install Xcode last version 7 (we tried on beta xcode7.2)

  2. create a symbolic link or copy of Xcode way ld: /Applications/Xcode-beta.app/Contents/Developer/Toolchains/XcodeDefault.xctoolchain/usr/bi n/ld to /lib/aot/bin/ld64/ld64

  I hope it solves the problem.

• Flex/Flash Builder development vs. others?

  Generation of application Flex/Flash Builder development has one advantage over the others? The bit I picked up appears to show that it can create an Android, IOS and Blackberry app in a project (of course specific build need to be addressed). I have not seen all up-to-date ways to learn Flex via Flash Builder 4.7. Everything I find seems to be 3 to 4 years. Still working with the material, I can say that it is somewhat outdated. Understand what he does, it seems to be a good platform to learn, but I wonder why the lack of attention to the basis of learning?

  Yes, everything you do in Flash can be done in the Air, most of the time with 100% of the same code. I recommend you to download FlashDevelop (its free, Windows only) and play with some examples of micro. After that, create a new project for mobile with FlashDevelop templates and reuse your code for mobile and compare the results.

  It's really easy once you understand the structure of the project basis and Air vs Flash. I think that the Setup is a bit difficult to understand if you are new to this, but after awhile, it will be a piece of cake.