AE CS4 does not start on the Multi-Core system

Similar Questions

• Dell XPS 8500 does not start after the interruption of system restore

  It was one thing to do, but I turned off my PC during the restoration of the system because he took time to complete the process.  The next day I couldn't boot into windows.  I tried the automatic repair feature, but it does not work.  I tried to repair windows using the orignal installation disk, but it does not work.  I tried to install Windows 8 all over again, but I got an error message - media pilot is missing.  I opened the box uninstall the RAM, videocard unplugged and both drives and reinstall, but without success.  I noticed that there is an orange/orange light on the motherboard.  I thought it was the hard drive at the beginning, but now I hope that this is not the motherboard.  Any help will be appreciated.

  RB

  You have damaged the image beyond repair.  You need to reinstall from scratch.  Windows to say that an optical drive driver is missing, bad copy of DVD-RW, DVD + R or DVD - R media that was not burned at 1 X 2 X or 4 X, so is not readable.  This is why USB Flash Drive 16 GB or more is recommended rather than the DVD player to the installation media.

  Why doesn't my CD or DVD drive?

  Troubleshoot installation of Windows 7 Service Pack 1

  A required CD/DVD drive device driver is missing
  A media computer driver needs is missing
  error message when you install Windows

  https://support.Microsoft.com/en-us/KB/2755139

  This problem occurs for the following reasons:

  The installation DVD is removed during the installation process.
  A bad quality DVD has been used to create the installation DVD.
  The speed at which the installation DVD is burnt was too fast.
  The DVD drive cannot read media.
  The ISO file is corrupted.

• Pavilion dm4-1160us does not start after the failure of system recovery

  I have Windows 7 Home edition is installed. In my view, it is 64-bit.

  I get everything by initializing the error message is:

  "BOOTMGR is missing".

  Press Ctrl + Alt + Delete to restart»

  When running various tests (Tuneup, break-in, Start-up, hard drive) in I always get the same failure ID: M4PC2J-5KQ6N0-XD6V41-60VG03. The poduct ID is XH124UA #ABA.

  The case began after my computer froze and I forced the reboot.

  I guess that the hard drive is a gonner. Is this correct?

  Hi Mario,.

  Personally, I recommend to replace the hard drive yourself - it is a surprisingly simple process (and much cheaper).  A brief guide on this is detailed below.

  Your computer is listed as coming with a 500 GB hard drive, but you can also easily install a 750 GB HARD drive if you want a little more space - readers at the following links are examples that would be perfect for your laptop.

  Hard drive 500 GB

  750 GB hard drive.

  The procedure to replace the hard drive begins on Page 61 of your & Maintenance Guide.

  Once this is done, simply use your recovery media to reinstall the operating system on the new drive - this is described in the document of HP here.

  If you do not have your recovery media, let me know because there is another option, you can use it as long as you can clearly read the activation of 25-character product key on your label COST.

  Best regards

  DP - K

• From itunes last update itunes does not start without the permission

  iTunes does not start after the upgrade. "The"itunes"folder resides on a locked disk or you do not write to this folder permissions.  I am the administrator. Windows 7 Professional.

  See the empty/corrupted after upgrade/crash iTunes library. This particular issue is addressed towards the end.

  TT2

• Mac does not start and the fans going crazy

  Computer does not start and the fans work hard and fast. Someone has an idea what is the problem and how can I solve this problem?

  OLA I will try help EU tenho um macbook pro, mas esse problema não me it happened ainda EU acho seria o seu mac origem help esse problema pode formatar better.

  SE nao tem'm ligar o seu osx para formatar use cmd + r e ligar pressionar cmd + r ele deve AI PODES ligar restore o seu novo osx.

• Two iMacs does not start after the 10.11.4 update.

  Two iMacs does not start after the 10.11.4 update.  Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd.  He then gets stuck in a loop trying to start.  Tried to reset the SMC and LANDAU.  Without success.  Started in recovery mode and ran disk utility.  Discs said OK.  Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).)  Installation is finished but still once does not start.  Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater.  Installation seems to work, but once again, the macs will not start.  Same 'unexpected launchd sigkill' error.  A mac is now back working properly with 10.11.3 the other will be shortly.  Is there a problem with the accession?  Our COMPUTER support use Munki to get updates from one day to the next.  Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.

  More information: two bricks iMacs were late 2013 models.  A 21 "and a 27.  We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• Satellite Pro L300-21F does not start and the screen remains blank

  L300-21F is aged 18 months, so out of warranty. When you press the power button, you can hear the fan and a "click" but the hard drive does not start and the screen remains blank. The power and the battery on the headlight LEDs, but the switch light does not work. I checked the power supply and it is 19.3V and substituted a good known. Removed the battery, tried with just the power cord and still nothing. Pressing ESC or F2 when you press the button power does not bring to the top of the screen of the bios or any other message. I have concluded there is no power the jury. A friend he had its technology take a look and he concluded Council is probably a friend.

  So my questions are:
  1. He's probably right?
  2. is it a common problem with an easy solution?
  3. what else can do before shelling out for a new Board of Directors?
  4. is there a link where I can find how to disassemble the case?

  Any help appreciated

  Hello

  > 1. He's probably right?

  Yes, it looks like motherboard failure

  > 2. Is this a common problem with an easy solution?

  If it's a motherboard problem, the whole motherboard is replaced. Quite expensive part...

  > 3. What else can do before shelling out for a new Board of Directors?

  I don't think you can do anything with fried mobo

  > 4. Is there a link where I can find how to disassemble the case?

  Take a look at the site called irisvista.com

• Z600: computer does not start after the installation of the 5 TB SATA drive

  My z600 refurbished does not start after the installation of a SATA of Toshiba 5 to disk.  After removing the drive, the computer starts.  I have my computer too old to handle a 5 TB drive, I something wrong or is the DOA drive?

  Thanks for the info.  I added the GPT to my search and discovered what had to be done in disk management.  Here is a page with step by step instructions and photos.  http://www.howtogeek.com/193669/whats-the-difference-between-GPT-and-MBR-when-partitioning-a-drive/

• Computer does not start after the screen goes blank &amp; Compaq.

  Hello

  A few weeks ago, I turned on my PC and it showed at the Compaq screen and then went to a blank screen & would not respond. I held the switch button to turn it off and after 4 attempts, it start fine. Next time, it took 20 attempts to initialize and now it does not start, it will be maybe if I try like 100 times he can do... The problem is when the Compaq screen comes up it comes only for like a second so I know that it does not start, if the Compaq screen stays for a few seconds as 3 + I know it will load windows and start.

  History > the computer originally had XP and has been replaced with VISTA memory was 2 * 512MB, but it was a bit slow and I was advised to upgrade. I bought 2 * 1 GB memory and put it in my PC a few months there may be 5 + had no problem so far.

  I tried the following:

  Remove the memory and replace it. Remove the 2 * 1 GB of memory and its replacement by the Moose 2 * 512MB to check if the memory is at fault.

  Cleaning of the dust around the fan (at this point, I removed the fan over the CPU and cleaned the thermal compound from the CPU to make it nice and shiny, only tried to start one time after that for a few seconds heard blowing fan and turend it took off. Depuis_lors, I realized that it wasn't just muck and had a purpose na derwiche put a little more on)

  Remove the battery of the BIOS for half a day

  Move jumpers CMOS from1, 2 to 2, 3 positions

  I can not get into the same if BIOS start and hold F1 he will show me the BIOS for a second and then go to a black screen.

  Specifications of the computer

  Compaq Presario SR1629UK desktop PC

  Details can be found in the following link

  http://support.HP.com/us-en/document/c00579251

  Your help would me much appreciated...

  Hi guys,.

  Thanks for your help, I wanted to just give you a batch update. After the grueling process of verifying the destop, memory suppression, cleaning it & all the other techo checks. I gave my pc to somone to look to the he tried not to turn on he opened it removed cleaning my thermal paste back on and told me it was working fine.

  When I bought home all happy, I realized that I had the same problem, I borrowed another monitor and found it worked well! So the question is with my monitor, if anyone has the same problem first check another monitor.

• I want to install WIN 7 on my Dell XP computer. The disc I bought says that the hardsrive must be clean first. The disc does not start on the existing XP. How can I do this?

  I want to install WIN 7 on my Dell XP computer. The disc I bought says that the hard disk must be clean first. The disc does not start on the existing XP. How can I do this?

  Hello

  Have you changed the boot order?

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order and boot from the Windows 7 DVD:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  Do install a cleaning, removal of the existing XP partition and create a new partition to install 7 on in the own installation process:

  http://www.SevenForums.com/tutorials/1649-clean-install-Windows-7-a.html

  See you soon.

• My pc says that windows does not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM.

  My pc says that windows does not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM. It is said it can be repaired by using the original installation CD, but we do not have. Any ideas please?

  The file is missing or corrupt is one of your files in the system registry.

  By far, the best way to recover from this is to go to another computer and create a free Hirens Boot CD.
  Download Hirens: <> http://www.hirensbootcd.org/download/ > (link at the bottom of the icon of the disk)
  Hirens CD burning <> http://www.hirensbootcd.org/burning/ >

  Once you create the CD, and then start your system of problem with this CD.  In the first window, select "Mini Windows XP" and wait for the system to start.  When it starts, go to the Hirens Boot CD menu and select
  Register-> Registry Restore Wizard.
  then follow the prompts.  This wizard will return a copy of your registry database from backups that are stored with your system restore points.  After the restoration, stop, remove the CD and restart.

  When you start your system, it is recommended to perform a system restore operation to ensure the consistency of your system
  "How to restore Windows XP to a previous state"
     <>http://support.Microsoft.com/kb/306084 >

  Also, this error is almost always accompanied, if not caused, the corruption of the file system.  Also a good idea to perform a check disk (chkdsk) operation with the option "repair".
  "How to perform disk error in Windows XP check"
     <>http://support.Microsoft.com/kb/315265 >

  The hard way to get back is covered in the following Microsoft KB article, but if you have installed a large number of service packs for your installation of XP, I don't give you many chances to get past part 1. (And there's also an installation CD to access the Recovery Console)

  "How do I recover from a corrupted registry that prevents Windows XP boot"
    <>http://support.Microsoft.com/kb/307545 >

  HTH,
  JW

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• Problems with my installation of Windows XP and my computer does not start on the CD.

  Hi, I need BIG help here please!... I wanted to do a fresh install of Win XP Pro, but my PC didn't boot from the XP CD... I changed the BIOS settings, the sequence start on CD, restart my PC and he kept boot from the HARD drive and the PC does not recognize that there is a CD-ROM drive. Once the start-up of the PC from the CD, I wanted to delete the partition and format the HARD drive, but it says "Setup could not format the partition...". "something like that... so what I did I have the PC from the boot CD, click in the command line and 'R' for repair, I wrote"format c:"and after that, I wrote" diskpart remove C:' so I deleted the old partition, create a new and when I wanted to install XP on it, I could not because the PC does not start from the CD... how can solve this? "

  Thank you!

  original title: HELP for the installation of Win XP.

  Hi Jorge,.

  So the only thing I can think is that it is a sort of master/slave thing.

  Your IDE HDD will be a Knight, probably alongside where the power cable is inserted, to dictate whether the player will be considered to be a master, slave, or cable select. Assuming that it is the only HARD drive in the PC, make sure it is designated "master". Then, in the BIOS, make sure that the boot order is specified as HDD0 first (as opposed to HDDx where x is greater than zero).

  In addition, assuming that the data cable is the new type of Ribbon with strands of 80, make sure that the blue connector of the IDE data cable is in the motherboard and that the end of the black connector is in the HARD disk and, if it is a two-disc data cable, do not use the gray connector.

  Tricky