After I deleted a message, it does not always go in the trash but disappears.

Similar Questions

• When I try to start my computer, it does not load anything. The backlog, but the rest of it runs bad and slow. I can't open any programs that either, and my pointer always told it to load.

  Original title: Please HELP

  When I try to start my computer, it does not load anything. The backlog, but the rest of it runs bad and slow. I can't open any programs that either, and my pointer always told it to load. Safe mode works, but I just don't know what to do. Help, please

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:
  Since it works fine in safe mode, I suggest you to try to perform the clean boot to safe mode and check if it helps:
  http://support.Microsoft.com/kb/929135

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  Method 2:
  Also, try to run the safe mode System File Checker and check if it helps:
  http://support.Microsoft.com/kb/929833

  Method 3:

  Be sure to run a full scan with your antivirus software.

  http://www.Microsoft.com/security/default.aspx

  It will be useful.

• OfficeJet 5741: e-mail does not completely print from the laptop, but the fact of the iPhone

  My e-mail does not print correctly from my laptop, but made my iPhone. Some pages don't print at all; a few cuts partial printing of pages at random. I have not had this problem with my Officejet 6500 Series. That's happened?

  Hi @edzoocator,

  Welcome to the Forums of HP Support!

  I understand that printing from your e-mail account to your HP Officejet 5741 printer does not work properly. I would be glad to help and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I see that you are able to print from your iPhone, but impression of your Windows computer 8.1 gives you problems. There could be a problem with the driver of printing or the application you are printing from.

  To check if you are using the correct printer driver, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing. What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  • Please try printing from another application to help isolate the problem.
  • Do you use a local web or e-mail client application-based e-mail account?

  There could be a problem with the Web browser you are using.

  • If you use a test of email based on web printing from other browsers such as Safari, FireFox or Google Chrome.

  To solve the problem with the problems causing the internet browser, follow these steps:

  Reset your Safari browser settings:

  1. Open your Safari web browser by clicking on the Safari icon in the dock.
  2. Click on Safari from the Safari menu, located at the top of your screen.
  3. A drop-down menu will appear. Choose Reset Safari....
  4. A dialogue warning now appears listing the components that will be removed.
  5. Click the button in the dialog box titled reset to complete the process.
  6. Your Safari browser will now restart automatically.

  Source

  Reset the settings of your Firefox browser:

  1. Type of topic: config in the address bar and press ENTER. A list of preferences.
  2. Find the print.print_printer preference (Note: this preference is missing in Firefox profiles where you have never used the printer.)
  3. Right-click (context-click) this preference and select reset. (Some users may have to reset all the preferences of print.printer for a particular printer, if this master preference reset does not solve the problem.)
  4. Restart Firefox and see if the problem is resolved.

  Source

  Reset your Google Chrome browser settings:

  1. In the upper right corner of the browser window, click on the menu of the Chrome Chrome
  2. Select settings.
  3. At the bottom, click Show advanced settings.
  4. Under the section "Reset settings", click on reset.
  5. In the dialog box that appears, click Reset.

  Source

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• HDR5010KB-digital recorder - signal does not always come through the use of HDMI

  Hello

  I bought the product above in October. Since then, I have had intermittent problems. When switching on the channel AV on my TV (a Panasonic TX-P42S20B) signal is not always crossed when you use the HDMI channel (I also connected via a SCART, and who works so always seems to be a problem HDMI.) It is particularly obvious when the recorder has been used for a while (be it for recording or playback.) It is not overheating (or if this is the case, not to the degree I get a warning message) and turn off the power to the electric network seems to correct the problem, but it's a pain.

  I tried to change the hdmi cable, as well as to try different channels AV on my TV and it did not help. Is this a common problem or make me a defective unit?

  Any suggestion would be appreciated

  Have you noticed the same problem using other devices connected to your TV (using the same cable)?

• News photo Magnifier does not always display, despite the use of 'I' or 'Ctrl I' to enable/disable/cycle information

  I often have a problem for magnifying glass, displaying information about the photo. I put the magnifying glass display of library and development of view options for my needs, but often the news does not, despite the use of Ctrl-I and 'I' to toggle / change information.  The only solution is to switch to Dev mode if I'm in the library, or switch mode library if I am in dev.  This has been a problem for at least a year now, and I keep hope it will resolve itself with the latest version.

  In my view, is the site of official bug report.

  Photoshop Lightroom | Community customer Photoshop family

• Library Media Player does not always update or the latest.

  My Windows Media Player library do not update or the latest that arrived it convert mov to MP4 using QuickTime Player Pro.  I even restart the computer, and still, he isn't here.  The file mp4 in question is 107 MB 50:54 minutes.  I am running Windows 7 64 bit Home Premium edition.

  I found the answer on the forum, Ms.  I deleted the WMP database by following the instructions.  I had to stop a related service (the WMP network discovery) to be able to delete the file (not in the instructions).  This succeeded, the reopening of WMP, I saw all my $ MP previously missing.  No need to install any codecs because I now use VLC media player.

• I have Photoshop cc 2014 but do not get access to scripted models. Ive just updated, but it does not always appear in the box to fill patterns. Anyone know why?

  Although I've just updated my cc photoshop I don't not scripted options model-someone ' one can tell me what could be the reason?

  You do not speak the most recent as the tree, flame and a framework? They moved to the filter > render in the menu bar.

  EDIT: Mark Gene as correct if that was the case. It took him until I did it.  xD

• Corsair POWER supply update does not post, powers of the powers of 5 seconds down and loops...

  Have the HP Pavilion Elite m9650f with motherboard replaced in April 2012 class good to go.

  Replaced the stock GPU Nvidia GeForce 9800 GT with a Zotac GTX 560 Ti GPU and

  the stock HP 460 Watt power supply with a W0388RU Thermaltake TR2 600 Watt PSU in may 2012.

  All goes well until October 2012.

  PC randomly starts shutting itself off the coast and not feed until I have unplug the power cord and wait 5-10 minutes.

  Finally, he stopped turning on all together.  Reinstall all power PSU connectors, etc.  same result.

  Removed all cards, etc, same result.  Cards reinstalled one by one, etc., same result.

  Reinstall the stock HP 460 Watt PSU, now everything works fine.

  Thought it was a premature failure of Thermaltake PSU.

  Bought and installed a Corsair CMPSU - 850TXV2 850 Watt power supply for a few days but still not good to go.

  Lights, fans spin, but no MESSAGE, no video, tracks for all

  5 seconds, stops, turns on itself over and over again.

  Reinstall all power PSU connectors, etc. same result.

  Removed all cards, etc, same result.  Cards reinstalled one by one, etc., same result.

  Reinstalled the HP PSU stock, now everything works perfectly again.  ?

  Spends hours reading the forums...

  Some say that the RAM may not report correct voltage for power supply.

  If so, what can I change RAM voltage in the BIOS?

  Others say reset CMOS I did, same result.

  And someone on this forum HP thought that perhaps the Pegatron IPMTB-TK

  Card mother Truckee can only accommodate up to 750 Watts POWER supply.

  Any ideas?

  Can I get away with just using my HP 460 Watt power supply after all stock?

  Thank you.

  I have an additive to add to this topic.

  To refresh, my questions focus on a possible shift of the power supply and card mother specs:

  What is an ATX 12 v 2.0 and above technical problem or a power CAP problem?

  I posted my questions on the Forum of power SUPPLY Corsair PSU

  at the same time and I paste it here now, a response

  to GUY of RAM.

  "Hey RAM GUY."
  
  Sorry I couldn't answer until now.
  
  Please specify the difference between the ATX 2.0 specification and 2.01
  
  Spec that the negative - 5 v Rail is not present in the 2.01 spec and
  
  beyond.  As I mentioned previously, the Thermaltake PSU that has been
  
  running in my 2009, HP i7 tour for 7 last month said 12 volt ATX 2.2
  
  on the case and even if the power supply HP OEM said 12 volt ATX
  
  2.0 in the technical literature, that I found on Google, the real PSU I have does not work
  
  have any note on the case ATX specification.  So I think it's safe to say, my
  
  motherboard does not have the negative Rail v-5 at which he played
  
  nicely with 12 volt ATX 2.2 spec, until recently.
  
  Although theoretically it is supposed to be no limit on the amount of
  
  Absorbed power, you can use to power your motherboard, the motherboard because
  
  is supposed to use only what suits him and cap the rest, it seems that the OEM
  
  can dial up limitations of power if they deem necessary.
  
  Could be as simple HP, without wanting to compete with some of his HPs
  
  Professional workstations, caps so power on some Pavilion Elite
  
  Series models to prevent them from becoming a much cheaper
  
  solution.
  
  In any case, I think that all the available information, digested, he does not speak
  
  Specification of the ATX, but rather my motherboard HP has a limit of 650 Watts of power
  
  If I think that I read that someone else got the same motherboard goes with
  
  750 watts, but I do not remember where to find this announcement. »
  
  I'm back and Yes!
  
  Thanks again Lasvegaswireman!

• I installed acrobat reader in window10 and demoted to the 8.1 window. After downgeading 8.1, acrobat reader does not run and also do not uninstall and reinstall. Only, I get the error message. What should I do?

  I installed acrobat reader in window10 and demoted to the 8.1 window. After downgeading 8.1, acrobat reader does not run and also do not uninstall and reinstall. Only, I get the error message. What should I do?

  Hi soyoungl9536964,

  Please try to run the cleanup tool "Download Adobe Reader and Acrobat tool - Adobe Labs" on your machine to remove all traces of the reader.

  Then, restart your machine and install the latest version of the player from here:

  Adobe Acrobat Reader DC install for all versions

  Let me know if any problem will persist.

  Kind regards

  Christian

• New message notifications does not disappear automatically

  Hello, everyone.

  I've had Skype for about two years now. Since I got it, it was convenient that the new message notification seems to go away when I look at the Skype window.

  Well, this is more the case.

  The new message notice persists, but it isn't permanent, fortunately. It goes away after I have send a new message to the group, or until I manually "mark as read".

  It's not a big deal, but it is rather annoying that it does not have its own more. I already tried to restart Skype and that does not seem to solve the problem.

  Suggestions?

  http://community.Skype.com/T5/Windows-desktop-client/Skype-chat-messages-are-in-the-wrong-place/m-p/...

• Could not open install Assistant.  I get this error message: cannot install the application due to a certificate problem.  The certificate does not match the certificate of the installed application, does not support upgrades of the application or is not

  How do I download a trial of 12 items, Adobe?

  I followed the instructions to download assistant... but get this message: the application cannot be installed because of a certificate problem.  The certificate does not match the certificate of the installed application, does not support upgrades of the application or is not valid.  Please contact the author of the application.

  Hi alposer,

  Please delete the copy of Adobe Download Assistant you have installed, and then reinstall Adobe Download Assistant.

  Kind regards

  Rave

• Dungeon, error message "Thunderbird does not' SOLVED use different antivirus CAUSE: MSE (Microsoft Essentials antivirus)

  As soon as I connect on Thunderbird, with any action I take, immediately I get the message "Thunderbird does not respond.

  It is and will always be a problem in Microsoft. I got exactly the same problem with MSE and Thunderbird at the time of Thunderbird 3. I've spilled the Microsoft Junk and have not looked back.

  There are a lot of free anti virus alternatives of MSE. Almost all of them offer more features and better success rates when catch bugs

• I get the message: firefox does not when I try to browse the web sites

  For some time now, when I load a web site, it takes a long time to load and then I get the message: firefox does not, or long-running script and does not. This occurs on many web sites, and when that happens, it takes a long time to browse this web site. I also have this problem on other browsers. Any suggestions as to what might help? Thank you.

  Hello

  Many issues of the site can be caused by corrupted cookies or cache. To try to solve these problems, the first step is to clear cookies and cache.
  Note: This will be you temporarily disconnect all sites, you're connected to.
  To clear the cache and cookies to do the following:

  1. Click the menu button

     

     , choose historic, then "Claire recent history...". ».

  2. Under "Time range to clear", select "all".
  3. Now, click the arrow next to details to toggle the active details list.
  4. In the list of details, see the Cache and Cookies and uncheck everything.
  5. Now click on the "Clear now" button

  More information can be found in the article remove the navigation, search and download history on Firefox .

  This solve your problems? Please report to us!

  Thank you.

• When I hit the play button to a voice message, it does not play

  I have an iPhone 5 and trying to listen to voice messages, it won't play.  I hit the play button (arrow) and the button show break but does not do anything, and the number of bands/message remains the same.  How can I fix it?

  Just recently did it start? Try restarting of strength:

  Hold the home and power buttons at the same time until the Apple start-up logo appears.

• After software update today, my password does not work.  My phone is now disabled.  I don't have a backup.  How can I start to use my phone again and not lose all my content?

  After software update today, my password does not work.  My phone is now disabled.  I don't have a backup.  How can I start to use my phone again and not lose all my content?  Help, please.

  You can not