After pressing the default from the factory to Raidar ReadyNAS Duo V2 gives the device is offline

Similar Questions

• Satellite A60 Shuts Down immediately after pressing the Start button / stop

  My A60 stops after 2-3 seconds when I press the power button to open the laptop. After pressing the power button, all the lights on, but until something appears on the screen, the computer cuts the power. Pleasure, DVD and disk hard audio work. At least, the sounds come from these materials. Also from the buttom of laptop, I see that the fan is running.

  This problem started anywhere Yesderday, I closed my laptop properly and carry my laptop to my friends. When I tried to open my laptop, this problem occurred and I could not open yet.

  I tried all combinations of use power supply and battery for power. Non of them works.
  Is there a had the same problem or have any diagonistics for this problem.
  Thank you

  Emrah

  Hello

  Try to connect the laptop to the external monitor to check if pictures or anything else appears on the second monitor?
  You can also try to use the FN + F5 combination to check if the display will change back to the internal display.

  But look, man, if you are not successful then I guess there must be a serious hardware problem and only the laptop technician might know what's wrong.

• How can move the pointer after press the play button when editing any file

  My PC is Windows 7, I buy and used hearing CS6 for more than 6 months, but I find the pointer can't move after press the reading change when we file.

  Your audio device is disconnected from the hearing. Go to Edit > Preferences > Audio hardware and restore the connection. When the transport fails, that's the only reason!

• How to reset the LED after pressing the stop button?

  Hello

  I use vi of green LED to indicate if the data has been loaded correctly. However, if I run the same labview program several times online, then the Green LED is always on because "value that data has been correctly loaded" crashes it since the previous session. Is it possible to reset all of the screws LED after pressing the button STOP (stop labview program).

  Thank you for the answers.

  Hope this helps:

• Computer to close after pressing the close button in windows

  I had a problem for my computer to shut down after pressing the close button in windows. Windows starts to make the closing process as its suppose there just like the computer is supposed to to close it restarts. Its like I pressed the button instead of the button closure. Please tell me how to solve this problem, so I do not have the power button to get off the computer.

  What has not worked? What happened when you tried?

  Another suggestion, take a look in the system logs and errors and warnings and post here Event Viewer Application copies. Do not post on that more than 48 hours ago.

  You can access event viewer by selecting Start, Control Panel, administrative tools, and Event Viewer. When searching for the meaning of the error, information about the event ID, Source and Description are important.

  A tip for posting copies of error reports! Run Event Viewer and double-click the error you want to copy. You will see a button resembling two pages. Click on the button and close Event Viewer. This places a copy of the report to your Clipboard. Paste it into the body of your message. Make sure that it is the first dough right out of the event viewer.

  Hope this helps, Gerry Cornell

• What I did, because I can't copy and paste any item, or I can't move it after pressing the 'V' or

  What I did, because I can't copy and paste any item, or I can't move it after pressing the key 'V' or 'ESC '? Can I cancel it anywhere? THX

  Version of InDesign? OPERATING SYSTEM?

  Is the locked object, or on a locked layer?

• Speakers stopped working after changing the device sound card

  * Original title: switched to hi-speed of dial-up, speakers stopped working / / rev. #2 Can I change the title of: speakers stopped working after changing the device sound card

  I have a Motorola SM56 speakerphone modem, I went from dial-up to the Road Runner.   When I open Device Manager and expand the sound column it lists "High definition Audio Device" (manufacturer of Microsoft), there are 4 that say "NVIDIA High Definition Audio" then there is one that says "Unimodem Half-Duplex Audio Device.  When I open the properties of the Unimodem device it says ' device working properly. "

  Let me start at the top under "General".  It lists the name of the device: Unimodem half-duplex Audio device.    Device type: audio, video and game controllers;    Manufacturer: Microsoft;    Location: Motorola SM56 Speakerphone modem.

  My speakers worked very well before I went.   I tried updating the driver but he came back with "best driver already installed.  It is a desktop PC, it is about 6 years old, but has been revised, graphics card new, updated to power, new 4 GB ram I think.  The hard drive is 1 TB.   I'm running Windows 7 Pro.  I forgot to mention, if I open a WMV file and volume in the taskbar commands, I see the green light moving.  The green light on the actual speakers turned on, just no sound.  It seems to me that the old speakers do not like the new modem from Time Warner. (I'm an old lady, what the devil I know)

  It is a question of another driver, or is it something else?

  Any help would be greatly appreciated.

  Are plug you the speakers into the modem?

  They must be connected in making your computer speaker, usually a light green color (read the manual of the machine). Go to control panel / sounds / playback and make sure that the type of speakers you selected as the default device.
  Audio device drivers updated its better to not use MS Update (it is not). Re-post giving your machine make name and exact model number (for example HP, Inspiron, ABC1234 etc.).
  See you soon,.
  Jerry

• El Capitan will not install. Window disappears after pressing the button install.

  Hello world

  Looks for some install help. I try to install El Capitan for my Mac Mini. Here are some features:

  Mac Mini (mid-2011)

  OS X Yosemite 10.10.5

  Intel Core i5 2.5 GHz

  Question: El Capitan does not install anything after clicking on the button after choosing the drive. The window simply disappears and nothing happens.

  I have read all the threads to locate the file "install OS X El Capitan", but it leads to the same question.

  What other options can I here? I tried to create a new admin user to install the operating system, restarted my computer, re - download the file, etc..

  I ran out of options here. Help, please!

  Please launch the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  The title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  Click on the clear view icon in the toolbar. Then take an action that does not work the way you expect. Select all of the lines that appear in the Console window. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name or e-mail address, can appear in the log. Anonymize before posting.

  When you post the journal excerpt, an error message may appear on the web page: "you include content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• Problem intermittent boot Tecra S2 after pressing the power button

  Hi all
  I have a Tecra S2 with the 6600go GFX card.
  The machine is large but presents the following problem.

  After that the machine was interrupted for a while it will start not reliable.
  You press the power button. Either as soon as you release the power button or a second later (changes every time) the green power light comes on. The fan spins at high speed then slows down to a crawl a few seconds later (as usual) but LCD does not illuminate.
  Also when it does not start USB devices are not initialized (I have a product key dongle which will flash if it is not initialized - when you start the laptop properly this dongle on continuous - a normal start, it is initialized before the ramtest BIOS)

  I've updated the bios a couple of times - it is now 2.4 (I noticed the power button timings were changed in the V1.9) but this has not solved the problem.

  I tried to start on the current with battery removed, ca battery & battery only - the result is the same.

  I can start later button power until the laptop off, wait a few seconds and then try to get back to work.
  After several of these cycles, it will begin eventually to the top. Recently, it seems that it took several attempts before start-up.

  If I have used the laptop for an hour or two and then turn it off it will start almost always a first time.

  If I put the laptop to sleep (orange slow flashing power LED) then half the time that it will continue when you press the power button - the other half of the power LED will switch to the green but the LCD display remains inactive & I switch the power button.

  Any help or advice would be welcome.

  Thanks in advance,
  Robin

  Hello

  This seems very odd.
  First of all: you can boot from USB only if the floppy drive is attached.
  You can boot from these devices USB-drive floppy/disk HARD/ODD/LAN.

  In my opinion the other unit starts the sound not as issues not a software problem.
  I think there could be something wrong with the hardware. But it is not easy to say what it could be exactly.
  You know, the look on the material is necessary.
  I recommend you contact Toshiba service partner in your country.
  They have much more experience in such cases. Guys can run tests and then can give you correct information about the failure.

• Satellite A200 23W stop seconds after pressing the power button / stop

  Hello all :)

  I just bought a laptop Toshiba Satellite A200 23W a few hours ago.
  I turn it on and let it complete the installation of Vista.

  After the installation of Vista finishing it asket to resturn laptop and from that moment, the laptop is "dead".
  After pressing on restart the computer (from Vista) computer turns off without problem, but he never did it again!
  After a few minutes of waiting, I tried to start it by pressing the power button.

  Now when I press the power button, I can hear the HDD work and most of the time until I see something on the screen of the laptop computer stops!
  Now, I noticed that both the battery indicator AND the DC IN light are hot flushing and stop Flash at times.
  Reading the manual, I guess that the DC IN indicator should Flash in all not well.

  I tried to uninstall the battery and try to start the laptop, but in this case I can't even listen to the HDD, commissioning!
  I try to unplag and replag (on the laptop as well as Jack) power cable but again no result.

  Any ideas of what past?
  Thank you very much

  I don't know what the problem is here and, in my view, should not be so important to you. Contact your dealer as soon as possible and to talk with him. Explain the situation. You will get may be new notebook. Otherwise, please contact the nearest authorized maintainer and let check your laptop.

  The laptop is brand new and it should work. Please do not wait too long.

• Wireless connection disappeared after pressing the button system Orange Cisco router WRT54G

  Trying to connect to a printer Dell wirless to the router and has failed, after many tests to get the computer to recognize the printer as a wireless device.  Recommended by Dell to refresh the router and I pressed the button in the above subject line.

  Now, none of my computers display the connection wireless as available. I have reset the time many cable modem and the router and him that restarted the computer and they still will not recognize the wireless connection.

  Also, I tried to use the default IP 192.168.1.1 to review my settings for the router (running a laptop directly via the cable modem), but the address keeps timing.

  What is someone out there knows what can happen to connect wireless to disappear?  Any help is greatly appreciated.  Don

  Your wireless network is gone because you press the WPS button on the front.  Never do this because you don't have the hardware to support it.  Change the SSID and password.

  Press and hold the reset on the back for 30 seconds and then release.  Wait 10 seconds and cycle power to the router.  To connect to a computer wired to the router at 192.168.1.1 only empty password, username "admin".   Now configure the router manually.

• Keep playing sound after pressing the home key in iOS

  Hello!

  I have an application that loads an MP3 from a URL and then read it (Flash cs6 - Air 3.9)

  In Android (when I publish it as APK), when the user press Power, or reduce the App, the sound continues to play (I like)

  But the same code in iOS, when I press Home or Power, the sound "paused" and continue playing only after I re - activate my App.

  I tried to resolve it with this line of code:

  NativeApplication.nativeApplication.executeInBackground = true;

  But without success.

  Everyone please help me what should I do to prevent the INTERRUPTION of the sound in my application after pressing Home and Power iOS ?

  Thank you in advance.

  Hi Pouradam,

  I know it sucks.

  On iOS, the only way to have a sound be played while the application is reduced to a minimum, is if the application is actually running in the background (obviously).  To do this in the application manifest, you must set UIBackgroundModes = audio, as follows:

  
  

  UIBackgroundModes

  audio

  ]]>

  However, since "batterygate" on iPhone4, Apple has been tightening its policy on applications that unnecessarily run in the background.  If the sound is supposed to play continuously (ex: music player), then they will * probably * be ok with it.  But if the sound is intermittent (even if it's the sound a clock radio alarm), they will likely ban.

  So, if you want your application to play intermittent sounds while in the background, your only chance is to configure notifications and associate a sound for notifications if you can.

  If you try the road local of notification, to help DONKEY of Juan Carlos Pazmino, however, that the sound function is broken right now, at least on iOS 5.1.1.  Also, at the time where he worked, I was not able to choose the sound through the app: I got was the standard "ding" sound.  Maybe push notifications are more robust.

  See you soon.

• Can't send emails... There is no action after pressing the Send button!

  When I press the button "Send" or "Send now" button directly from the upper left corner or even through the 'File' tab, the email does not get sent. In fact, there is no action at all. There are has no pop ups showing message of progress or error messages. Its just empty!

  If I try to save the e-mail, it is saved correctly but nothing happens when I press send.

  I'm not familiar with "check and send".

  Have you tried Thunderbird running in its safe mode? This would tell us if an add-on is causing your trouble.

  https://support.Mozilla.org/en-us/KB/safe-mode

• HP DV9700 not start. Farm in seconds after pressing the button walk / stop.

  My HP Pavilion DV9700, who works under Vista, stopped working yesterday.  I never did at the Windows startup screen.  Messages on-screen messages which function key to press for configuration, see starting, etc...   then stops.
  
  It started a day ago. I don't think that windows is the question.

  I tried to hard reboot... blew compressed air into the power supply area... no change.

  Don't know what to try next.

  Thanks in advance for any help you can provide.

  Steve

  Had to take the machine a tech I know.  It was the motherboard.   Thermal paste had disappeared from the excessive heat of the CPU and GPU and the poor ventilation of the machine design.   Costly, preventable and unnecessary repairs... HP was worth investing in better design systemboard for their laptops and notebook computers.

  HP response... your notebook $ 1200 of the scrap and buy another... and they will add the warranty one year.

  They thought that 5-6 years I got my laptop has a long service life of the device.

  I was actually insulted by this response and doubt my next laptop will be HP.

  Thanks to those who have tried to help however.

• Visa read only works after press the button run

  Hi people.

  I have a weird problem here. When I run the vi and press the Start button that the serial port is read and in the rest of the program works very well. When it is finished and do it again there is no data series. I have to give up and re - run, then when I push the button to start the serial data are there. The end of the program is somehow the serial port to an unknown state?

  Thank you

  Select this option.

  You may have found an error in your devices.  and, since you do not have initiallize the shift register with the grouping of the IO Sessions and mistakes the SR will retain the error while the vi is in memory, unless you give up running (how the shift register will contain the default value).  Find the error