After that put 5.3 to level of provisioning has stopped

Similar Questions

• Access to the network in all virtual machines lost after that put 8.1 to level.

  Today, I upgraded my host computer to Windows 64-bit Pro 8.1. I did the upgrade through the Windows store. There are no errors or problems during the upgrade.

  However: The host machine equipped with a Qualcomm E2200 network adapter, and it runs the 'Killer' Network Manager software called at startup. After the 8.1 update, when the machine did its last restart, Qualcomm Network Manager opened with a message that the LSP has not mapped correctly. I clicked 'YES' to remap it. Probably a stupid move on my part.

  Thereafter, I lost all network connectivity in all my virtual machines. I have virtual machines for Windows 8, Windows 8.1 RTM (not the preview) and Ubuntu 12.04 LTS. ALL of them have lost the network.

  The host computer has no network problem and works well after the upgrade.

  Any ideas or suggestions to reset network connections in virtual machines?

  All virtual machines are set to use NAT.

  Oh I have to say also that the host computer is running VMware Workstation 10 and everything was fine and dandy, has never had problems at all until this upgrade/LSP remap thing. I have install VMware Tools in the VM of Windows 8.1, with no effect at all.

  Thank you.

  -J

  Two things, I'll try:

  1. go in the virtual network editor and restore settings. The culprit is probably the VMNet to NAT configuration.

  2. If this does not work, it seems that the virtual card for NAT does not somehow. The simplest workaround is to uninstall and reinstall the workstation.

• Equium A210 - after that set BIOS to update the DVD player has stopped working

  Hi, since I have recently updated my BIOS, my DVD drive has stopped working on my Equium A210-1AS with Vista 32 bit.

  I tried the program fixme Microsoft who does not work, upper and lower register isn't here ether in regedit.
  Someone at - it solutions for getting the DVD drive working again?

  Thank you

  Hello!

  The CD/DVD drive is listed in Device Manager? You see an error code?
  If the drive is listed in Device Manager, you should try to remove it, and then restart the laptop.

  Try to load the default settings in the BIOS.

  Have you tried to remove the upper and lower filters by yourself? Here is the solution from Microsoft:
  http://support.Microsoft.com/kb/314060

  Good bye

• After that put 4.1.2 to level, starting XP hangs on the task of updating the tools

  I upgraded to Fusion 4.1.2 on Max OS 10.7.3.

  After the upgrade, XP still hangs partially through start, after that I connect to my user.

  I can evetually bring up the Task Manager with CTRL-ALT-DEL task manager tells me that what looks like tools vmware update process consumes 99% of my CPU.  Once I have kill this task, XP end its commissioning and works OK.

  How can I fix?

  Thank you.

  Manually uninstall the tools inside the virtual machine (from Control Panel), and then install them manually after a reboot.  Cancel any automatic installation which begins.

• problem with adding line in tabular form after that put 4.1.1 to level

  We have recently installed the Update 4.1 .1. We now have a problem with some of our tabular forms created using the wizard. The delete and update feature works fine, but when trying to insert a new record, it will insert only the first record, but after that, it will no longer inserts. It acts as ApplyMRU (updated online Multi) is not at all shooting. No success or error message. I tried to create forms based on the rowid and also on the suites (with and without triggers), and they all behave the same way.
  
  This happens both in IE and Mozilla. Tabular forms were working fine before the upgrade.
  
  Everyone knows this?

  We just hit this issue and thanks to this thread and a light bulb above my head, resolved this question today. There is more to the story. Copy the necessary images in place works, but get the full version 4.1.1 images.

  We were already on 4.1.0.00.32, so I applied only Patch 13331096 upgrade to 4.1.1.00.23. Patch 13331096, at least one that I downloaded a few weeks ago IS NOT ALL OF THE NECESSARY IMAGES.

  Fortunately, I thought to download both. When I did a number of files in the directory images between the full version and the patch, the County came up short for the patch.

  If you have this problem, get your hands on the full release 4.1.1.00.23, NOT Patch 13331096and copy these files to image in place. Who sets the we.

• Not able to use iTunes after that put 12.3.3 updated

  Not able to iTunes after put 12.3.3 updated

  After installing update iTunes to 12.3.3 (after the prompt), I'm not able to use Itunes. When ever open in 10 seconds a pop-up message is displayed which says that itunes has stopped working. a problem caused the blocking of the program works correctly. Please close the program. two close options to obtain the program and the program to debug.

  Please help solve this problem

  Hello! Try the steps suggested here:

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  If you can't install or update iTunes for Windows - Apple supports

  I hope this helps!

• Add a homegroup password after that put Windows in place is over and a password was not entered during the set up process

  Hello

  I had a hard drive crash and had a new hard drive installed.  At the end of the recovery process, I was asked to answer questions such as the choice of a language.  I also had the opportunity to put a password in a homegroup. Not entered a password.  BIG MISTAKE.  I can't reach my home group now because I do not have a password.  I don't have the ability to change the password that I never entered one in a first time.  Unless someone can help me, it seems that my only option is to make the process of recovery everywhere.  My concern, there is that I won't be able to download Microsoft Office almost again because it won't let me this time.  I activated once and he didn't allow me to activate again. But he did.  I think that he won't let me activate a third time.  Can someone tell me where I can go to add a password to my homegroup.  No help from HP or Microsoft Windows has been useful.  I have Microsoft Windows 7 Home Premium.

  Hi kschoff.

  
  Thanks for posting your query in Microsoft Community.
  
   
  From your description, I understand that you are unable to add a password for home group after that Windows set up was complete.
   
  I suggest you create a new group home and check.
  
  Follow the link that will help you create a new group of home.
  http://Windows.Microsoft.com/en-us/Windows/HomeGroup-help#HomeGroup-start-to-finish=Windows-7&V1H=win8tab1&V2H=win7tab1
  
  Hope the above information helps.
  Make it happen to us and made me know the status of your question so that I can fix it as soon as possible.

• Ethernet DHCP fails after that put 10.11.3 updated

  Hello

  After that the updated 10.11.3 updated my ethernet connection fails to connect to the internet.

  The general link is fine; router OK, other computers will work properly; DHCP works for iPhones, iPads and WiFi on this computer are great

  • I have tried several things from other threads.
  • the cable is connected
    • but I realized during disconnection of the cable as the IP address and the subnet mask disappear (as must I guess) to reconnect the cable, it takes a few seconds and I have again the values for both:

  IP 169.254.159.37

  subnet 255.255.0.0

  The connection says it is a self assigned IP address, but there is no connection to the internet.

  Any ideas?

  (Is there a way to reset/restart the DHCP client service for individual cards?)

  hardware problem identified with switch that solved the problem

• Mac Pro (2013) will not wake up from sleep after that put 10.11.2 up-to-date

  Problem:

  After that Mac Pro goes to sleep, keyboard and mouse enter don't wake him. Disconnect and reconnect the monitor will not help either. Unplug the monitor wouldn't be helped either. Hotkeys to stop will not help either. (I use Mac since 1986, so I know more tricks). The only thing I can do to start to use my Mac is again holding down the button of physical power for five seconds and make a hard stop.

  Background:

  It is a problem that sometimes in the past. However, it is not reproducible and usually one of the steps above might work, such that unplug the monitor (a Dell 4 K 27 ") of the power supply and then plugging.

  I use physically connected (USB) keyboard and mouse.

  Current state:

  After the 10.11.2 system update last night, my Mac Pro shows this problem every time he sleeps.

  He has already hit a critical delivery photography and currently affects a submission of work for the city.

  This is urgent.

  Other users have reported the same problem after 10.11.2. I've not seen a solution

• Airport most convenient that the range extender today broke up after that put 7.6.7 at level

  I have two extreme airport connected with an ethernet cable, one for upstairs and one for down. One downstairs is set to extend the reach of the network wireless created by one on the floor. Also the one upstairs is configured in Bridge mode because I have a server that I use for DHCP and DNS, instead of using the airport for that. The server and the airport on the floor are connected to the same network switch.

  Everything worked very well under firmware 7.6.4. But after the upgrade to 7.6.7 and without changing any settings, now my network is terribly broken. No devices can connect to the wifi network, and the network interface on the server shows errors like "has received the package on eth1 with own address as source address" and "Null supervisors, receiver of broadcasting not ready."

  The problems went away by unplugging the airport down.  But this isn't a good solution.  I want to have both, and I want that they function as they did before.

  When you have airports connected by ethernet... YOU MAY NOT USE EXTEND WIRELESS.

  The result is the following.

  Server shows errors like "has received the package on eth1 with own address as source address" and "Null supervisors, receiver of broadcasting not ready."

  You create a loop where packets are going around and around the system.

  If you say you had it past 7.6.4 firmware and it was broken by 7.6.7 well, I can only say that he has never worked on any firmware with a switch or other device which is able to break loops.

  Return to 7.6.4 and see if it still works.

  I found that Wireless extend over 7.6.7 is more restrictive than the firmware as soon... I highly recommend 7.6.1 for it... as I can show 7.6.4 reproducible problems but it is also a case that former airports are losing just their WILL... I had success extend wireless who recently failed... and it's purely too big range... considering that it used to work properly. Which shows that the products are just slow decline.

  I also get numbers of the absurdity of airport utility that I still don't understand.

  for example. I got the link to work on a new Gen5 TC (refuses to bind on Gen4 TC)

  

  If I click on the unknown link, it shows a link 450Mbps speed which is impossible. The RSSI is also what you would get with the two devices within 1 foot of the other (30 cm) No 20 M through several walls and a floor.

  The end of TCgen5 by using the utility v5.6, I see the actual rate...

  

  The link is showing 54 Mbit/s and a signal-78dB which makes much more sense. Unfortunately the other end does not record again... and the value 0 for the noise is also wrong.

  Noise on the latest diagnostics wireless displays 0 for a lot of wireless.

  

  Something rotten in the world of the Apple to the end... What with the CCMM giving a total mess to Airport utility if people use it...

• Open the folder crashes finder after that put 10.11.4 at level

  After the installation of El Capitan, the viewfinder must be restarted after I get the beachball when I try to open a new finder window or try to open any folder on the desktop. How can I fix? I'm on an iMac 27 ".

  Please launch the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  The title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  Click on the clear view icon in the toolbar. Then take an action that does not work the way you expect. Select all of the lines that appear in the Console window. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name or e-mail address, can appear in the log. Anonymize before posting.

  When you post the journal excerpt, an error message may appear on the web page: "you include content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• You are able to load the plugin settings after that put 10.1.1 to level?

  After the last update of GB that I am not able to load the settings of plug-in via .pst files - they are greyed out in the standard dialog box - and they are still same after copy them in the standard folder (under /Music).

  I am able to save the new setting, but does not load them via the next-> load menu in the window of the specific plugin parameters.

  Any help/feedback would be apreciated! Thank you!

  -Claudio

  El Capitan 10.11.4

  After the last update of GB that I am not able to load the settings of plug-in via .pst files - they are greyed out in the standard dialog box - and they are still same after copy them in the standard folder (under /Music).

  What box are you using?

  I can open PST plug-in in the plug-ins pane in the Info of the smart control panel, for example to open a "Preset" Space Designer. And my plug-ins saved opens thus: for example:

  

  I saved my own preset as MyAmphitheaterExtrem.pst of ~/Music/Audio Music Apps/plug-in Settings/Space Designer / s 02.5 MyAmphitheaterExtrem.pst and copied pst two presets in Logic Pro X in the same folder.  Then I quit garageBAnd and recorded market and my saved preset appeared in Space Designer Panel, as well as logic copied presets.

• % 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; Connection refused because of the failure of the path opposite. NAT VPN clients problems after that put 8.3.2 to level.

  I've recently updated to 8.3.2 and I have been informed of these NAT changes, but even after reading the https://supportforums.cisco.com/docs/DOC-12569 I am still unable to rectify the communication network 192.168.100.0 VPN with hosts on 172.16.1.0 and 172.16.9.0. VPN clients connect to the external interface, and I try to ping inside and the demilitarized zone, respectable 172.16.1.0 and 172.16.9.0 hosts. VPN client shows that the two previously mentioned networks such as roads of security, but still not to the ping pong.

  # sh nat

  Manual NAT policies (Section 1)

  1 (inside) to the (whole) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  2 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  3 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  Auto NAT policies (Section 2)

  1 (dmz), to the source (external) static obj - 172.16.9.5 interface tcp www www service

  translate_hits = 0, untranslate_hits = 142

  2 (dmz) (outdoor) source static obj - 172.16.9.5 - 01 interface service tcp 3389 3389

  translate_hits = 0, untranslate_hits = 2

  3 (dmz) (outdoor) source static obj - 172.16.9.5 - 02 interface tcp ldap ldap service

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) (outdoor) source static obj interface - 172.16.9.5 - 03 service ftp ftp tcp

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) of the source static obj - 172.16.9.5 - 04 interface tcp smtp smtp service

  translate_hits = 0, untranslate_hits = 267

  6 (inside) source static obj - 172.16.9.0 172.16.9.0 (dmz)

  translate_hits = 4070, untranslate_hits = 224

  7 (inside) to (dmz) source static obj - 10.1.0.0 10.1.0.0

  translate_hits = 0, untranslate_hits = 0

  8 (inside) to (dmz) source static obj - 172.16.0.0 172.16.0.0

  translate_hits = 152, untranslate_hits = 4082

  9 (dmz) to dynamic interface of the obj - 172.16.9.0 - 01 source (outdoor)

  translate_hits = 69, untranslate_hits = 0

  10 (inside) to the obj_any interface dynamic source (external)

  translate_hits = 196, untranslate_hits = 32

  I think you must following two NAT config

  NAT (inside, outside) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 192.168.100.0 obj - 192.168.100.0
  NAT (dmz, external) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 192.168.100.0 obj - 192.168.100.0

  Please configure them and remove any additional NAT configuration and then try again.

• USB plays is not in the car after that put 9.3.4 at level

  I have an IPhone 6 and own a 2010 ford fiesta.

  After upgrading to IOS 9,34 I can't read podcasts or music through the car radio with USB cable, radio do not even recognize the phone is plugged in, although it will charge the phone and play via Bluetooth. and all the phone features work very well.

  It worked fine before the upgrade and the desire to return to the use of usb cable because it it allows to use the steering wheel radio controls.

  Ford blame Apple an Apple accuses ford. I had updated the firmware made by ford dealers.

  seems whenever apple do a update it fucks things up

  Sometimes an iOS update breaks compatibility and you will have to wait for an iOS update or a firmware update for the system of ether.

  However, try the following:

  Try:

  -Reset the device iOS. Nothing will be lost

  Device iOS Reset: Hold down the On / Off button and the Home button at the same time for to

  ten seconds, until the Apple logo appears.

  -Reset the car.

  -Go to the support site for Ford and see if they know anything or if a firmware update is available for your car

  -Reset all settings

  Go to settings > general > Reset and tap reset all settings.

  All your preferences and settings are reset. Information (such as your contacts and calendars) and media (such as songs and videos) are not affected.

  -Restore from backup. See:

  Restore your device from an iCloud or iTunes backup - Apple Support

  https://support.Apple.com/en-us/HT204184

  -Restore factory settings/new iOS device.

• After that put 2.0.1 to level, contacts have two facebook links

  After having installed the 2.0.1 upgrade, I had to be re-authenticated connection to Facebook.

  My contacts who had ties to facebook, have now two links of facebook.  How can I get rid of the duplicate link?

  I do not have this problem myself but go into the settings of facebook app and choose "Delete all data of facebook" or what he says and then reapply facebook sync