After that start monitor/screen becomes black with visible vertical lines

Similar Questions

• Qosmio F60-100 - after that upgrade RAM screen goes black

  Hello world
  I upgrade my RAM a g-skill 2 * 4 GB 1066 Mhz DDR3
  I have a Qosmio F60-100
  I am on Windows 7 pro N
  I checked whether they have updated bios (the toshiba soft explain to me, that there is not an update available)
  I checked if the RAM were compatible with my laptop (these have been suggested to me)

  When I put the new RAM in the laptop, in "Starting Windows", the screen goes black and the fan works hard.
  So I'm not able to install my new RAM.

  These ram are compatible with my laptop?
  What is the problem?

  Thanks so much for all those who can help you.

  PS: English is not my mother tongue, sorry about that...

  Hello

  According to your Qosmio notebook specifications can be improved up to 8 GB. The comparable memory modules are:
  2 GB DDR3-1066-PA3676U-1M2G
  4 GB DDR3-1066-PA3677U-1M4G

  I don't know that references your RAM modules but the behavior described is probably as a result of the use of non compatible modules.

• Windows Vista crashes, the screen becomes pink with diagonal dotted lines

  My HP Pavilion DV9500 laptop started making a few months ago:

  The computer and the programs sometimes simply freeze, sometimes the screen becomes a light pink with diagonal lines dotted, and sometimes the laptop itself restarts without warning.  The computer is about 3 years old now and have not had any problems before this.  I tried to do a clean install of the recovery feature that I don't have a Vista disc to reinstall from, and he always does this.  Sometimes the computer will be fine for a few hours and sometimes just after the start it will freeze.  A couple of times too, as it starts, Windows will not start and it will say "Not found operating system".

  Hello

  It sounds like imminent hardware failure/issues. Since you did a clean installation of recovery
  pretty much excludes most of the causes of software if it could be driver related and there are other
  possible causes remotely. Video/display and its drivers are suspected leader and mother.
  Board and power supply.

  Keep good backups and check with a real store of the computer (not the leeks and glances at a BestBuy, etc.)
  BigBox stores) or the manufacturer of your system Support.

  ===============================

  It's my generic convenience store and eventually it can help you determine the cause but I strongly
  suspect material.

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during "blue screen of death," collisions
  Displays information on all the "crash" of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• After compaq splash, the screen is black with blinking cursor.

  Hello

  I have a CQ45-217TX, I had installed openSUSE and decided to install a different linux OS. During the installation, there was a problem and I had to give up. The power stopped in my house, causing the laptop turn off because I do not keep the battery in it so that at home.

  Now, when I start the laptop I can reach the BIOS but all start result just options in the black screen and a cursor. I have run all the tests in the BIOS and all passed. I also checked to see if the hard drive is recognized, which is.

  My windows Cd is in Taiwanese that I can not read, but does not start when even (I tried to see if I could intuitively reinstall it)

  Any advice would be greatly appreciated.

  Solved. Subsequently managed to start with external CD drive.

• Satellite M200 screen turns off after that start & battery does not charge

  Hello, I am from Jakarta, Indonesia
  I have a problem with my Toshiba Satellite M200 Notebook (running Windows 7 Home Premium)

  After I press the power button to the top of my laptop, it works fine display BIOS and Windows startup screen.
  but after that my monitor off all of a sudden when Windows is supposed to show the login screen.

  Sometimes, the monitor doesn't turn off, but shows a lower resolution (I don't know exactly what resolution, 1024 x 768 or 800 x 600, i use maybe 1280 x 800)
  so the only thing I can do is, press the power button to stop bad then press power again turns on, my monitor works normally
  try to stop and then turn on again in a few hours later, problems still comes once.

  from the moment where I install Windows 7, I use 8.15.10.1930 version of the driver (downloaded from Download Center of Intel, which included Assistant TV Intel)
  2 days ago, my friend told me that I should install the driver from the Toshiba site support, so I went to csd.toshiba.com and download the 8.15.10.1825 version of this site (which is not included Assistant TV Intel)

  my monitor works normally after I installed the driver I of csd.toshiba.com, so I think that the problem because the Intel TV Wizard somehow messed with my laptop. But this morning this problem once again, my turns just monitor suddenly...

  In addition, this problem seems to be my battery was unable to recharge, my completely reloaded Windows shows, but when I plugged my AC adapter,
  There are 15-20 minutes before my laptop turns off automatically

  Three months ago, I just brought my laptop to the local Service Center of Toshiba and bought the new motherboard to replace my old mobo (which have a VGA problem too!)
  Is there something I can do (related to Windows or driver/software) or I can bring my notebook at the center of service again?
  are they somehow an incorrect wiring when replacing my motherboard?
  and am I need to replace my battery too?

  I use this laptop for about a year and a half and there is nothing wrong with my battery before replacing the motherboard

  any help would be appreciated :D

  Hello

  Talk about your screen, the a graphics driver causes this malfunction with resolution and turn off. Go to the page of the toshiba driver and download the correct Vga driver for your model. I see, you are running Windows 7, if there is no driver for win7, try the vista driver.
  On your power supply, you have used for the year and a half and he is released in 20 minutes, there is nothing strange. It's standard for power supply operating period, need to be replaced. Just to be sure, you can check with a new battery. You will see that the trick works as expected.

  Welcome them

• Since the upgrade to 8.0, when navigation between screens, my computer screen becomes black for 1 second before the screen is redrawn. This happens regularly and is a major nuisance. It simulates a power failure. It does not happen with IE.

  Since the upgrade to 8.0, when navigation between screens, my computer screen becomes black for 1 second before the screen is redrawn. This happens regularly and is a major nuisance. It simulates a power failure. It does not happen with IE.

  Here I answer to my problem: I upgraded my graphics card and the problem seems to have disappeared.

• All my applications are late, everything on the screen becomes black.

  whenever I have start my app store, in any application, for example when it is started it begins to lag everything on the screen becomes black until I have move my mouse over the screen, but as soon as I take my mouse it goes black again, facing the same problem with all applications. Even lag setting window also even that store about some apps are broken as video it starts and whenever I play that he stop working (even I reinstalled the application several times, but of no use)

  Please perform a refresh of the system on the following model:

  · Press the Windows key + C on your keyboard to show the charms (if you use a touch screen: touch the right edge of your screen and drag your finger to the left)

  · Click settings

  · Click change PC settings

  · Click general in the left column

  · Under refresh your PC without affecting your files, click Start

  Then follow the instructions that will be provided on-screen to cool your PC.

• C855-13D satellite after 5 minutes, my screen becomes dim

  Can someone help me please?
  I use a laptop Toshiba Satellite C855-13D with 64-bit Windows 7.

  After 5 minutes, my screen becomes dim unless I move the mouse.
  In order to disable this I need to go into the Advanced mode in eco service department.

  But on my laptop there is no Advanced tab. I've got report and help settings.
  No advanced. I went on YouTube and saw the Advanced tab there.

  So why missing on my laptop and how can I get it back?

  Hi demoome

  I think that the ECO profile has been selected in Win 7 power Managemnt.

  You can change it easily.
  Go to control panel (change the icon display, small or large)-> power management
  Here you will find plans of different powers.

  Choose the one you want to use: for example the balance.
  Now, click on change Plan settings

  Now, you can find the option called the brightness
  Here, you can assign the value of the battery and AC adapter mode.
  Finally, apply the changes.
  All that s

  Here's a nice video of Microsoft
  http://Windows.Microsoft.com/en-us/Windows7/products/features/power-management

• 15 r007TX 15 HP laptop: HP laptop screen stays black with the mouse cursor flashing

  Hello

  Here I am facing probhlem. my laptop is started but screen stays black and a slider is binking on that...

  I just perform a clean boot and once I restarted my laptop and then I faced this problem...

  Please help me...

  I have laptop HP 15 15-r007TX with windows8.1 64 bit having 4 GB RAM with i5 4 genration processor with dedicated 2 GB and 1 TB of hard disk graphics card...

  Please help me...

  Thankss...

  Hi @Shawnfrost,

  Welcome to the HP Forums!

  This is a great place to find answers and information!

  You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums Learn how Post and more

  I understand that when you start your laptop, you get a blank screen with a blinking cursor.

  Here is a link to help overcome this problem.

  Computers laptops HP - computer won't start (Windows 8)

  It can also help.   Laptops HP - computer will not start and the lights blink or the computer will beep.

  If you enjoy my guarantor please click on button below congratulations to say thank you.

  If it solves your problem, please click the solution in order to allow other people to find this information.

  Best of luck and have a great weekend!

• When I activate a new session in Teamviewer screen becomes black. How can I avoid this?

  When I activate a new session in Teamviewer screen becomes black. How can I avoid this?

  On Fri, 28 September 2012 13:46:38 + 0000, abehaim wrote:

  When I activate a new session in Teamviewer screen becomes black. How can I avoid this?

  TeamViewer is not part of Windows, and is not a Microsoft product.
  You should communicate with TeamViewer for a question like this.

  Ken Blake, Microsoft MVP

• I was running Mozilla firefox on my computer until two weeks ago. At that time, the screen went black and now I am not able to use it.

  I was running Mozilla firefox on my computer until two weeks ago. At that time, the screen went black and now I am not able to use it.  When I click on the icon and open to the top it says cannot load xp.com and a flag of resolution comes up saying it can't run a resolution less than 1930 x 2300. I have no idea what this means and how I can solve this problem.  I thought that maybe the application was bad, so I deleted and then added it back on and it does the same thing.  I even did a restore of the system to try hard but nothing I did the work.  So, how can I solve this problem.  I'm not a computer genius, so he must be explained in simple easy to understand instructions.

  Hello

  I suggest that you view in Mozilla Firefox community because there seems to be a Firefox problem.

  https://support.Mozilla.org/en-us/

  Some examples of the problem:

  «I can't open Firefox, it says could not load xpcom.» Who is wrong? »

  https://support.Mozilla.org/en-us/questions/965228

  "I get an error"Unable to load XPCOM". I know that I can reinstall Firefox, but how do I save my favorites?

  https://support.Mozilla.org/en-us/questions/1029239

  'Error message cannot open the XPCOM and impossible to open ALL pages '.

  https://support.Mozilla.org/en-us/questions/1006494

  Here is a YouTube video on fixing this error:

  https://www.YouTube.com/watch?v=x_C2eaNj234

  See you soon.

• Motorcycle G screen becomes black and white, the names of the app

  Hello my motorcycle g screen becomes black and freezes, and also most of the time like every day my phone will be white all app names is there a way to get rid of this problem?

  Maybe you met the problem described here. Using a different pitcher like Launcher Nova should help. The update which should improve as well.

  See you soon,.

  Nicole

• is it possible that a single screen will work with the slider and second focus mode

  Hello

  can you please tell me is it possible that a single screen will work with cursor mode and second focus mode.

  Thank you

  Hello

  I don't think that it is possible to change the mode of the development of your application outside of in the config.xml file.

  A custom extension may be able to do this, but I have not seen anyone this yet.

• My screen seems to have gone out.  Everything worked well then there black and white vertical lines on the screen.  Had to make a hard stop, bury ashes hold the power button. Now no display

  does that mean if my screen on m MBP15 inches starting to show black and white vertical lines and will not again after that I tried to restart my computer?

  This looks like a bad graphics card. What happens if you hold a flashlight on the screen, you see the desktop or not?

• How ca I remove the yellow background (with red vertical lines) all my videos to my preview screen?

  In recent weeks, all of my videos (even those created before) now have a yellow background with red vertical lines when I stop (only when I stop). That, when I export, it creates the vertical issues with colors.

  I finally had someone from the tech group to answer! Here's the answer: the issue you report is a known problem / bug in first 2015 on mac 10.11 with Nvidia graphics cards. I advise you to change the rendering engine for 'Software only' for this problem.

  and it worked! Hooray!