AHCI driver Pavilion g6 - 1202q A1Z50EA

Similar Questions

• XP Sata AHCI Driver/help for Pavilion dv6t-2100?

  I need to downgrade laptop my sister to Windows XP, due to some compatibility issues with his favorite game. It's a DV6t-2100, as I said in the title, and I looked everywhere for the driver! I found an AHCI driver here on the Intel site, but I don't know that one to install from the file iaAHCI. Here is the list. Those with x. I've used. I have a limited amount of CD so I don't want to keep wasting them:

  AHCI controllers:
  -Intel Desktop/Workstation/Server Express Chipset SATA AHCI Controller
  -Mobile Intel (r) Express Chipset SATA AHCI Controller

  X Intel 5 Series/3400 Series SATA AHCI Controller
  -Intel (r) 5 Series 4 Port SATA AHCI Controller
  -Intel (r) 5 Series 6 Port SATA AHCI Controller
  -Intel(r) ICH10D / DO SATA AHCI Controller
  -Intel ICH10R SATA AHCI Controller
  -Intel(r) EP80579 SATA AHCI Controller
  X Intel(r) ICH9M-E/M SATA AHCI Controller
  -Intel ICH9R / / DH SATA AHCI Controller
  -Intel(r) ICH8M-E/M SATA AHCI Controller
  -Intel(r) ICH8R/DH / SATA AHCI Controller
  -Intel ESB2 SATA AHCI Controller
  -Intel(r) ICH7M/MDH SATA AHCI Controller
  -Intel ICH7R/DH SATA AHCI Controller

  Thanks in advance.

  Hello:

  Please read the XP downgrade guide at the link below:

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and/General-XP-downgrade-Guide-for-HP-laptops/TD-p/83267

  Consult the instructions for your model in the guide, which is located under 'Models difficult.'

  Paul

• SSD in AHCI on Pavilion m9350be mode

  Hello

  I installed an SSD (Samsung 840 EVO) in my Pavilion m9350be. Windows 7 recognized the HD and the drive works normally. Impossible to run in AHCI mode. When I change to AHCI raid in the BIOS, the PC unbootable.

  Thanks a lot for your help!

  Hello:

  You would need to change the BIOS to AHCI setting and then reinstall the operating system.

  I don't know anyway, that you can modify it by adding the driver AHCI RAID mode and then change the setting to AHCI.

  You can add the IDE mode AHCI driver, restart and change the setting in the BIOS to AHCI, but not with the RAID.

• Where is the SATA AHCI driver for the NB200 notebook?

  I searched the forum and I know that I should integrate the drivers under XP with Nlite, but I Don t find the NB200 AHCI driver in the driver download section!

  I don't know much about your model, but if you publish the chipset model, I'll try to find it for you:

  http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=38

• Satellite L500D - AHCI driver for Windows XP

  Help, please.

  I need to install Windows XP on a Satellite L500D - 16K on AHCI mode not compattible. I can't find on toshiba or amd AHCI controller needed for this motherboard support notebooks, I can not even find the name of mothers everywhere.

  If I can use it on a stick for installing xp. pls help with a link or a Council

  Hey Buddy,

  I put t know what model of Satellite L500D you have exactly, but I can really recommend to read the discussions in the forum first before you start a new question. This has already been discussed 100 times before

  The AHCI driver, you can find in the package of official website of Toshiba display driver:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Check this box!

• Portege R830-10V P/N: PT321E AHCI Driver for Win XP 32 bit

  Hello

  I'm looking for driver AHCI Inter chipset 6 series 32bi Win XP. I can't find any work. Tried drivers from toshiba web, I tried web drivers of intel - was trying to google for 4 hours in 2 men. His does not work.

  I can't have win 7 on it, because I have Windows NT 4.0 Domain control and Win 7 does not work.

  So, its simple, I have Windows XP installed with all the AHCI drivers.

  What do you im? Force just install driver AHCI (in the hardware Manager)-online BSOD appears, badly restarts, get bios and change the Compatible in AHCI. I got BSOD again, error is unaccesible by car or something like that so I don't know, I have bad driver. Should I change compatible and try a different driver. I tried this way, all the drivers package from toshiba support web and other Google.

  I had a call with the help of toshiba authorized and that they cannot help me, because they do not know.

  Please, can you, someone help me?

  Thank you.

  Perhaps this Toshiba HowTo might be useful for you
  [How to integrate the AHCI driver when installing Windows XP | http://aps2.toshiba-tro.de/kb0/HTD9401AN0000R01.htm]

• Need Win XP AHCI Driver for my Satellite L500d-159

  Need of WXP AHCI Driver for my Satellite L500d-159

  Thank you

  Hello

  Satellite L500d-159 seems to belong to the series of PSLT9E.
  European driver Toshiba page provides all the drivers Win XP!

  The laptop supports an ATI graphics chip and the graphics card driver contains the SATA/AHCI driver as well.

  Then download the graphics of the page of the European driver Toshiba driver.
  In the package, you will find only the exe file run this exe file after the package was extracted, you will have to go to the SBDrv\SATA folder
  You will find the .inf file that is a SATA driver!

  Welcome them

• G550 AHCi driver to floppy/CD/USB player

  Greetings,

  Where can I download the AHCi driver for Windows 7 x 64 Home Premium for this laptop please? Lenovo G550. I am installing Corsair GTX neutrons and HP Windows 7 x 64 is unable to see the HARD drive, I tried many drivers, but I get always wrong size of SSD, so they must have been wrong,

  Please advise,

  concerning

  Bryan

  Well, I solved it by putting the Corsair neutrons GTX in HP ProBook s 4540, windows setup it and that it proceed with reassembly in G550.

• 14 - r103ng: including F6-AHCI-Driver for Windows XP (32-bit)?

  Hello Sir,

  I bought a "14-r103ng", and I'm a big Fan of Windows XP (32 bit).

  I got BlueScreens with "..." Your... »

  Later, I tried to install XP with F6 and AHCI-DriverFloppy-Image on USB.

  It seems to work, but I have several possibilities for the choice.  I don't know, I have to select Intel-driver.

  Can you tell me, if TI is possible to install XP on this laptop modern and if so, which driver should I choose?

  Hopefully, you can help me. Best regards, Tim

  Hi, Tim:

  It is not possible to install XP on your laptop.

  There is no sata AHCI driver for XP for models with N pentiumN/celeron processors.  Is there no drivers graphics Intel for Windows XP for this chipset and processor.

  The last specification chipset based Intel XP can be installed on would be one with a processor of 3rd generation with a 7 series Intel chipset.

  Now, if you want to try to add these W7 SATA AHCI drivers I zipped and attached, you can put it on the disk.

  I highly doubt they will work, but I guess you have nothing to lose by trying.

  Even if they do, you will always have the problem of no graphics driver.

• Windows 7 Pro (64 bit) has no install the AHCI Driver

  When I built my current computer system in May 2011, I have not encountered this problem with installing 64-bit Windows 7 Pro on the new 500 GB Western Digital HARD drive.  In fact, I installed Win7 three times (to wipe the drive with DBAN after the first and second installs) before I was satisfied with the third installation.

  Before the first installation, I configured the BIOS of card mother Gigabyte GA-890FXA-UD5 (Maj) SATA AHCI (with SATA 3.0) and copy the driver AHCI of CD Gigabyte on a SanDisk Cruzer USB (4 GB).  The GA-890FXA-UD5 (revision 2.1, version of the F6 BIOS) has an AMD chipset.

  During each installation, the Win7 Installer reported that she could not find a HARD drive and offered the option to load a driver.  I used this option, and the installation program displays a dialog box with whom I sailed the Cruzer to select AHCI driver.  Each time, Setup loaded the driver with success smoothly.  Of course, I still have the installation of Microsoft Windows 7 Pro DVD, purchased with a full license of the retail.

  Example: two years later, after that I started to meet various problems for which I could find no cause, no resolution, I suspected malware or corruption of the registry.  To make a long story short, eventually I decided to erase the internal HARD drive once again, after you save the data files on an external USB HDD.

  Win7 Setup now follows the same routine, of course.  Except that now, it will fail to load the driver AHCI of the SanDisk Cruzer (!).  I've also removed the Win7 installation DVD, loaded the CD Gigabyte, sailed to the driver and selected.  The Win7 Installer is always not load.  In addition, before you run the Win7 Installer for other attempts, I connected the USB HDD external and sailed to a copy archived AHCI driver on it, but Win7 Setup could not load.  I have made many and repeated attempts, with all the storage media at hand, that contains a copy of the driver AHCI files, but not joy.

  For what it's worth, I also ran the software on the repair disk I did shortly after installing Win7 Pro, and he couldn't load the driver AHCI of the SanDisk Cruzer with CD Gigabyte, respectively.

  Then I reconfigured the BIOS of the motherboard to SATA IDE (with SATA 3.0) and rebooted the system.  You might think that Win7 Setup would have a suitable driver for the AMD SATA IDE, since she has one for the reader to optical disc Samsung DVD-Writer (obviously), but it did not find a HARD drive.  Then I sailed in the appropriate driver AMD x 64 on the CD of Gigabyte IDE files, but Setup cannot load it, too.

  Question: why Windows 7 Pro 64-bit Setup does not install the driver AHCI, and what can I do about it?

  Hello

  Thanks for posting your query on the Microsoft Community.

  AHCI (Advanced Host controller) makes the NCQ (Native Command Files) with connection to warm or hot swapping through host controllers SATA Serial - ATA possible; Vista was the first to offer this feature. The problem with AHCI is that it must be enabled in BIOS before the installation of the OS. After installing the operating system will disable the PC. The reason why Windows disable the AHCI drivers not not needed during installation.

  I suggest you activate the AHCI after installing the operating system if you already enable AHCI in the BIOS, when you installed the operating system.

  Warning: This section, method, or task contains steps that tells you how to change the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  322756 (http://support.microsoft.com/kb/322756/ )
  How to back up and restore the registry in Windows

  1. in the window for the start menu search box, type regedit, click with the right button on the entry, click run as administrator, enter your credentials of the user for the UAC prompt, and then click Yes to Open regedit.
  2. in regedit, navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services.
  3. in the left pane, click msahci, in the right pane, double-click Start to change.
  4. in the window that opens, change the value to 0 (zero), and then click on OK.
  5. in the left pane, click on iaStorV (if he), in the pane, double-click Start to change. Repeat step 4and continue with step 6 below.
  NOTE: From: Error Message Occurs after you change the mode of the boot drive SATA
  6. close the registry editor.
  7. now you will need to reboot the PC and go into the BIOS and enable the AHCI. When Windows starts, it will finish installing the AHCI drivers.
  8. you will need a final restart to complete the process once the drivers are installed.

  We hope that this information helps to let us know the State of the question, we will be happy to help you.

• The AHCI driver installation failure

  I have a BIOS Gigabyte GA-MA770T-UD3 (1.0). F9G. When I try to load the AHCI driver for Gigabyte, I downloaded, I get a Setup error failed every time. If I set the BIOS to AHCI or not, the driver has still not install. If I leave the BIOS set to AHCI Windows freezes on-screen swirling of the points and I restart and change back the IDE BIOS. If I go to Device Manager, as suggested in another post, there is no entry for the SATA drivers or controllers even though all three of my drives are connected to the SATA ports on the motherboard. So far, there is nothing that I found that will solve this problem so I can properly configure my Samsung 859 Pro SSD. Suggestions?

  1, after a BIOS update, a shutdown of the pc is preferred. In addition, generally, BIOS settings

  by default, do not have SATA controller or RAID installed, it must be set manually

  for this purpose in the BIOS... In addition, any type of HD we use with this pc, is not

  drivers pc looking for, its all simply enable the BIOS, everything is 'plug & play '.

  or youre a setting (on or off), setting controller drivers is a windows

  adjustment, & the BIOS configures the establishment to run for windows...

  Whatever it is, try this link for more information.

  https://social.technet.Microsoft.com/search/en-us?query=AHCI&AC=2#refinementChanges=60&PageNumber=1&showMore=false

  In addition, make sure that battery MB is new, old batteries need BIOS

• Pavilion s3505f: AHCI on Pavilion s3505f

  Hello

  I just replaced the hard drive on my s3505f of Pavilion with an SSD and wanted to activate the AHCI on the computer.  I wasn't able to find a reference on the SATA mode in the BIOS of the PC (Phoenix - AwardBIOS r. 5.23).  Have not been able to find definitive information on the SATA ports to the motherboard Irvine for the PC, but I suspect they are SATA 1 (1.5 Gb/s) instead of SATA 2 (3 Gb/s with the AHCI support).  Transfer rates by an average of 110 MB/s in non-AHCI mode.

  I am aware that the AHCI drivers must be enabled in Vista before a change of SATA to AHCI mode in the BIOS.

  No confirmation on the types of port SATA card mother Irvine would be greatly appreciated.

  Thank you!

  You are the very welcome.

  Yes, AHCI is a subset of RAID in some respect, but not to an SSD work better on a model as old as yours.

  The only time where RAID is as good as that AHCI is if you have a PC with an Intel Series 7 or more recent chipset, which has SSD trim support RAID if you can't change the settings from AHCI storage controller, and you have installed the Intel Rapid Storage Technology technology for this chipset driver.

  The only thing RAID will do to your PC would be to allow for native command queuing, which is ideal for a mechanical hard drive, but a litle on an SSD, since there are no moving parts in SSD.

  Here's the only native made command queues...

  http://en.Wikipedia.org/wiki/Native_Command_Queuing

  Motherboards are made to HP requirements by the MFR of motherboard.

  If there is no setting in the BIOS to change the setting of the drive controller, then I doubt that it will be possible to do - even with a BIOS update.

• Tecra A11 - 1F4 (PTSE0E-OM6052EN) which XP AHCI driver?

  I am trying to install the drivers for XP on a Tecra A11 AHCI;

  I have a ghost image that loads on this laptop in compatibility mode in the BIOS and I try to update the driver for the drive in AHCI controller, restart & change the disk to AHCI mode in the BIOS.

  That's what I usually do for HP laptops, we have, and it works most of the time.

  Storage power Toshiba drivers are in the form of an executable that will only work if you have AHCI enabled, how anyone runs in compatibility mode supposed to use these?
  They don't even extract driver files, you can use only the .cab files and an installer.

  I have listed in the device under IDE ATA/ATAPI controllers Manager;

  Intel (R) 5 Series/3400 Series Chipset Family 2 port Serial ATA Storage Controller - 3B2D
  Intel (R) 5 Series/3400 Series Chipset Family 4 port Serial ATA Storage Controller - 3B 28
  Primary IDE channel
  Primary IDE channel
  Secondary IDE channel
  Secondary IDE channel
  3 entries for Peter card reader &

  Intel drivers, I downloaded from-

  s http://downloadcenter.Intel.com/Confirm.aspx?httpDown=http://downloadmirror.Intel.com/21730/eng/f6flpy-x86.zip&lang=eng&DwnldID=21730&DownloadType=Driver & OSFullname = Windows + XP + *.

  .. .and it gives me the list of controllers to choose;

  Intel (R) 5 Series 4 Port SATA AHCI Controller
  Intel (R) 5 Series 6 Port SATA AHCI Controller
  Intel (R) 5 Series/3400 Series SATA AHCI Controller
  Intel (R) 7 Series Chipsets SATA AHCI Controller
  Intel (R) 7 series/C216 Chipset Family SATA AHCI Controller
  Intel (R) Desktop/Workstation/Server Express Chipset SATA AHCI Controller
  Intel(r) ICH10D / DO SATA AHCI Controller
  Intel(r) ICH10R SATA AHCI Controller
  Intel(r) ICH7M/MDH SATA AHCI Controller
  Intel(r) ICH9M - E / M SATA AHCI Controller
  Intel (R) Mobile Express Chipset SATA AHCI Controller

  The device ID of the controller (Intel (R) 5 Series/3400 Series Chipset Family 4 port Serial ATA Storage Controller - B 3, 28), I'm trying to install the drivers AHCI is;
  PCI\VEN_8086 & DEV_3B28 & SUBSYS_00011179 & REV_06\3 & 115 83659 & 0 & FA

  Please can someone tell me which of these to use with the above material?

  It takes me ages to build, install, bluescreen & rebuild to try again...

  Thanks for sharing!

• No SATA AHCI driver for 6440 b

  Hi all!

  * Yes, I have read the sticky on the SATA drivers - did not help.

  Us have just bought 5 laptop computers HP 6440 b to test (and would buy a lot more), but we have a problem with the installation of win XP on it when mode = AHCI - just SATA cannot find a driver for it! The latest Intel Matrix Storage Manager driver does not contain the AHCI drivers for these:

  Hi again,

  Slipstream only 6 Port of PCHM SATA AHCI Controller driver with your XP CD-DVD "blank." Use this driver Intel Sata.

  There is error in the guide that I found.

• Still need AHCI driver for Win XP for Satellite L500D-159

  I apologize for the insistence, I followed the path of Tonny, but the pilot, that it is not set, compatibly Xp is slower and I can't use the dual boot with Win 7. I tried with Nlite + Xp, but he continues to not read the fixed disk. Thank you

  Seems that you talk on this thread:
  http://forums.computers.Toshiba-Europe.com/forums/message.jspa?MessageID=198612

  I put t understand the driver is part of the suggested by Tonny such graphics card driver
  The pilot was found in the graphics card driver as well
  Please check and read the readme.txt file in the driver folder. Perhaps he could provide more details
  Sorry mate but there is no other driver SATA SATA driver in the folder of the graphics card is the right one

  Please make sure that your Win XP disk contains at least SP2 but better would be SP3

  PS: If you use the SATA driver then the SATA mode must be on AHCI

  Welcome them