AIR-LAP1041N >; AIR-AP1041N
Hello
I have a LAP1041N AIR. I understand that it is possible to turn this device into the AIR-AP1041N Cisco by downloading new software in the access point.
Can someone help me by downloading the correct software and give a guide to do.
Cisco want to sell a smartnet contract, but we didn't need...
Many thanks in advance, Arend
Hello
Yes, we can convert the LWAPP AP to AP autonomous... Here is the link to download the picture...
Download this image c1140-k9w7 - tar.124 - 25d.JA.tar
And please follow the instructions of the below document iOS LWAPP
https://supportforums.Cisco.com/docs/doc-14960
Let me know if this answered your question!
Concerning
Surendra
Tags: Cisco Wireless
Similar Questions
-
Cisco 2960 and uplinks AIR-AP1041N
Guys,
what I'm doing wrong here? I need to enable trunking to pass on several VLANs to my AP, but when I put the 2960 as trunk mode I lose connectivity to the AP.
All will help it useful!
Course AP Interface congfigs:
interface GigabitEthernet0.210
210 native encapsulation dot1Q
no ip route cache
Bridge-Group 1
No source of bridge-Group 1-learning
Bridge-Group 1 covering-disabled people
end+++++++++++++++++++++++++++
210 native encapsulation dot1Q
no ip route cache
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
Bridge-Group 1 covering-disabled people
end2960 new switch port config (lost connectivity to AP unless I put back to access the mode vlan210 why?)
GigabitEthernet1/0/1 interface
AP USTCRLW001 description
switchport mode trunk
SRR-queue bandwidth share 1 30 35 5
priority queue
MLS qos trust cos
Auto qos trust
endAdd this on swicthport where AP is connected:
GigabitEthernet1/0/1 interface
AP USTCRLW001 descriptionSwitchport tunk native valn 210
switchport mode trunk
SRR-queue bandwidth share 1 30 35 5
priority queue
MLS qos trust cos
Auto qos trust
endConcerning
Remember messages useful rates
-
Can I convert an independent AIR-LAP1041N-E-K9?
Hello
I have a new AIR-LAP1041N-X-K9 Access Point I want to use as stand-alone device (without a WLC controller).
Is it possible to convert it to become autonomous AIR-AP1041N-x-K9 access point?
Here is the release of version see the:
Version AP70ca.9b04.ee00 #SH
Cisco IOS software, software C1040 (C1140-RCVK9W8-M), Version 12.4 (23 c) JA, VERSION of the SOFTWARE (fc3)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Updated Wednesday, June 1, 10 12:53 by prod_rel_team
ROM: Bootstrap program is C1040 boot loader
BOOTLDR: C1040 bootloader (BOOT-C1140-M) Version 12.4 (23 c) JA1, RELEASE SOFTWARE (fc1)
AP70ca.9b04.ee00 running time is 3 hours, 41 minutes
System to regain the power ROM
System image file is "flash: / c1140-rcvk9w8-mx/c1140-rcvk9w8-mx".
Cisco AIR-LAP1041N-E-K9 (PowerPC405ex) Prozesseur (revision A0) 98294K / 32768K bytes of memory.
Card processor ID FCZ1541W0M1
PowerPC405ex CPU to 333 Mhz, the 0x147E revision number
Last reset of tension
Image LWAPP 7.0.94.21 version
1 gigabit Ethernet interface
32K bytes memory simulated by flash not volatile configuration.
Basic Ethernet MAC address: 70:CA:9 B: 04:EE:00
Part number: 73-14034-03
Kit numbered PCA: 800-34273-04
Revision number of PCA: A0
Serial number of PCB: FOC153813TT
Top Assembly part number: 800-34284-02
Top of page the Assembly serial number: FCZ1541W0M1
Top of page revision number: A0
Product/model number: AIR-LAP1041N-E-K9
Configuration register is 0xF
If it is possible, should what procedure I follow?
Thanks for any help!
Yves
Hello
Found a YouTube video for the same
http://www.YouTube.com/watch?v=QQ_NuxdRhQ4
You will need to download the image of the site of cisco
Thank you
NikhiL
-
Trouble with the voice and data Vlan vlan translate between CT3905 and SF300 - 24 p
Hey actually, we have the solution to monitoring of implementation with CT3905 phone, SF300 - switches 24 p cameras and AIR-AP1041N Access Points
We have the problem with the vlan tag in SF300 switch ports - 24 p we can´t tag vlan of the voice and data VLANs on the same port on SF300 - 24 p it is Possible or we must dedicate a port for each VLAN or ussing the same data segment of VLANs and vlan voice?
Someone has an answer or technical documentation that can help us
Best regards
First of all,
Please disable lldp transmit in SF 300 switch.
The command is "no lldp transmitted."
After you disable check the following steps.
https://supportforums.Cisco.com/docs/doc-27005
facing the same problem with cisco SG 300 and 3905 ip phone switch.
And nested thing was my 7945 and 6941 phones use to work properly, without above configuration.
Cisco 3905 became not vlan Ip address votes and even if I put static, it did not work.
After a long struggle, I was able to solve the problem. Now both phone and system work fine in the same port.
Samantha
-
Cisco AIR-LAP1041N-E-K9 does not not with WLC 4402 version 7.0.116.0
Hi all
appreciate your support for a problem I started to deal with today. I have a Cisco WLC 4402 running the 7.0.116.0 version and it's great to work with 25 Cisco 1252 access points. We received a new 20 Cisco 1041N APs today and I installed one in our site, but it does not work. He well worked and loaded the flash image and obtained WLC ip through DHCP option address and began to show the below error:
* 00:00:10.021 Mar 1: % SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: crypto IOS FIPS self-test passed
* 00:00:10.033 Mar 1: * CRASH_LOG = YES
* 00:00:10.333 Mar 1: 1 Port is not presentSecurity base.
MAC Ethernet address of base: C8:9 C: 1 D: 53:57:5E
* 00:00:11.373 Mar 1: % SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: crypto RADIO FIPS self-test passed on Dot11Radio interface 0
* 00:00:11.465 Mar 1: % LWAPP-3-CLIENTEVENTLOG: reading and initialized AP event log (contains, 1088 messages)
* 00:00:11.494 Mar 1: State of the voice_diag_test of WLC is false
* 00:00:12.526 Mar 1: % LINK-3-UPDOWN: Interface GigabitEthernet0, changed State to
* 00:00:13.594 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed State to
* 00:00:13.647 Mar 1: % SYS-5-RESTART: System restarted.
Cisco IOS software, software C1040 (C1140-K9W8-M), Version 12.4 (23 c) JA2, VERSION of the SOFTWARE (fc3)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Updated Thursday, April 13, 11 12:50 by prod_rel_team
* 00:00:13.647 Mar 1: % SNMP-5-start COLD: SNMP agent on host APc89c.1d53.575e knows a cold start
* 00:08:59.062 Mar 1: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 1 Mar 00:08:59.062: bsnInitRcbSlot: slot 1 has NO radio
* 00:08:59.138 Mar 1: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 00:08:59.837 Mar 1: % SSH-5-ACTIVATED: SSH 2.0 has been activated
* 00:09:00.145 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
* 00:09:09.136 Mar 1: % ADDRESS_ASSIGN-6-DHCP: Interface GigabitEthernet0 assigned address DHCP 172.16.26.81, mask 255.255.255.0, hostname APc89c.1d53.575e
* 00:09:17.912 Mar 1: % PARSER-4-BADCFG: unexpected end of the configuration file.
* 00:09:17.912 Mar 1: State of the voice_diag_test of WLC is false
* 00:09:17.984 Mar 1: message logging LWAPP to 255.255.255.255.
* 00:09:19.865 Mar 1: % CDP_PD-4-POWER_OK: full power - supply NEGOTIATED online
* 00:09:19.886 Mar 1: % LINK-3-UPDOWN: Interface Dot11Radio0, changed State to
* 00:09:20.873 Mar 1: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
* 00:09:20.874 Mar 1: % SYS-6-LOGGINGHOST_STARTSTOP: logging to host started 255.255.255.255 - initiated CLI
Translate "CISCO-CAPWAP - CONTROLLER.atheertele.com"... the domain server (172.16.40.240)
* 00:09:29.029 Mar 1: % CAPWAP-5-DHCP_OPTION_43: the 172.16.100.102 drive address obtained by DHCP
* 08:27:02.000 may 25: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
* 08:27:02.001 may 25: % CAPWAP-5-CHANGED: CAPWAP changed State to
* 08:27:03.175 may 25: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.16.100.101 peer_port: 5246
* 08:27:03.177 may 25: % CAPWAP-5-SENDJOIN: send request to join 172.16.100.101
* 08:27:03.177 may 25: % CAPWAP-5-CHANGED: CAPWAP changed State to ADHERE
* 08:27:03.329 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state CFG
* 08:27:03.333 may 25: % DTLS-5-ALERT: WARNING received: close notify alert from 172.16.100.101
* 25 May 08:27:03.333: % PEER_DISCONNECT-5-DTLS: Peer 172.16.100.101 has closed the connection.
* 08:27:03.333 may 25: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.16.100.101:5246
* 08:27:03.378 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 08:27:03.378 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 25 May 08:27:03.378: bsnInitRcbSlot: slot 1 has NO radio
* 25 May 08:27:03.448: State of the voice_diag_test of WLC is false
* 08:27:14.000 may 25: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
* 08:27:14.001 may 25: % CAPWAP-5-CHANGED: CAPWAP changed State to
* 08:27:15.185 may 25: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.16.100.101 peer_port: 5246
* 08:27:15.186 may 25: % CAPWAP-5-SENDJOIN: send request to join 172.16.100.101
* 08:27:15.186 may 25: % CAPWAP-5-CHANGED: CAPWAP changed State to ADHERE
* 08:27:15.330 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state CFG
* 08:27:15.333 may 25: % DTLS-5-ALERT: WARNING received: close notify alert from 172.16.100.101
* 25 May 08:27:15.334: % PEER_DISCONNECT-5-DTLS: Peer 172.16.100.101 has closed the connection.
* 08:27:15.334 may 25: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.16.100.101:5246
* 08:27:15.379 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 08:27:15.379 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 25 May 08:27:15.379: bsnInitRcbSlot: slot 1 has NO radio
* 25 May 08:27:15.450: State of the voice_diag_test of WLC is false
* 08:27:26.000 may 25: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
* 08:27:26.001 may 25: % CAPWAP-5-CHANGED: CAPWAP changed State to
* 08:27:27.182 may 25: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.16.100.101 peer_port: 5246
* 08:27:27.183 may 25: % CAPWAP-5-SENDJOIN: send request to join 172.16.100.101
* 08:27:27.184 may 25: % CAPWAP-5-CHANGED: CAPWAP changed State to ADHERE
* 08:27:27.329 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state CFG
* 08:27:27.333 may 25: % DTLS-5-ALERT: WARNING received: close notify alert from 172.16.100.101
* 25 May 08:27:27.333: % PEER_DISCONNECT-5-DTLS: Peer 172.16.100.101 has closed the connection.
* 08:27:27.333 may 25: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.16.100.101:5246
* 08:27:27.377 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 08:27:27.377 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 25 May 08:27:27.377: bsnInitRcbSlot: slot 1 has NO radio
* 08:27:27.433 may 25: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 08:27:27.446 may 25: % PARSER-4-BADCFG: unexpected end of the configuration file.
* 25 May 08:27:27.447: State of the voice_diag_test of WLC is false
* 08:27:27.448 may 25: % LINK-3-UPDOWN: Interface Dot11Radio0, changed State to
* 08:27:27.456 may 25: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
* 08:27:38.000 may 25: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
* 08:27:38.001 may 25: % CAPWAP-5-CHANGED: CAPWAP changed State to
* 08:27:39.183 may 25: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.16.100.101 peer_port: 5246
* 08:27:39.184 may 25: % CAPWAP-5-SENDJOIN: send request to join 172.16.100.101
* 08:27:39.184 may 25: % CAPWAP-5-CHANGED: CAPWAP changed State to ADHERE
* 08:27:39.326 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state CFG
* 08:27:39.329 may 25: % DTLS-5-ALERT: WARNING received: close notify alert from 172.16.100.101
* 25 May 08:27:39.329: % PEER_DISCONNECT-5-DTLS: Peer 172.16.100.101 has closed the connection.
* 08:27:39.330 may 25: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.16.100.101:5246
* 08:27:39.375 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 08:27:39.375 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 25 May 08:27:39.375: bsnInitRcbSlot: slot 1 has NO radio
* 25 May 08:27:39.446: State of the voice_diag_test of WLC is false
* 08:27:49.000 may 25: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
* 08:27:49.001 may 25: % CAPWAP-5-CHANGED: CAPWAP changed State to
* 08:27:50.179 may 25: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 172.16.100.101 peer_port: 5246
* 08:27:50.180 may 25: % CAPWAP-5-SENDJOIN: send request to join 172.16.100.101
* 08:27:50.180 may 25: % CAPWAP-5-CHANGED: CAPWAP changed State to ADHERE
* 08:27:50.323 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state CFG
* 08:27:50.326 may 25: % DTLS-5-ALERT: WARNING received: close notify alert from 172.16.100.101
* 25 May 08:27:50.326: % PEER_DISCONNECT-5-DTLS: Peer 172.16.100.101 has closed the connection.
* 08:27:50.326 may 25: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 172.16.100.101:5246
* 08:27:50.370 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 08:27:50.370 may 25: % CAPWAP-5-CHANGED: CAPWAP changed state of DISCOVERY
* 25 May 08:27:50.370: bsnInitRcbSlot: slot 1 has NO radio
* 08:27:50.425 may 25: % LINK-5-CHANGED: Interface Dot11Radio0, changed state down administratively
* 08:27:50.438 may 25: % PARSER-4-BADCFG: unexpected end of the configuration file.
I searched the difference in regulatory areas between AIR-LAP1041N -E- K9 and AIR-LAP1041N -A- K9 and no difference was found which may affect the operation of this access point.to cite our WLC configuration for regulatory areas is:Country set AR codesArea of regulation 802. 11A:-A802.11bg:-aMy question is should I just include my country in the WLC (IQ) add the field of requlatry (-E) to solve this problem? or change the country will affect the operation of all APs workers?Appreciate your kind support,Patrick Q.Try adding a European country to your regulatory domain.
-
I have a MacBook Air, I tried to clean below the space bar. I think I broke it because when I put back it together it is incredibly hard to push and I need to move so he could push. How can I fix? I just need to get a new keyboard?
Make an appointment at the Genius Bar in Apple for the service. If you need a Apple Store - find a store - Apple.
-
2 Air 10 iOS iPad dropping wifi
I have an iPad 2 air in perfect condition, since it first came out. I have the cell phone/Wifi version with Verizon. My problem has been lately, when connected to wifi, the wifi shuts on the iPad many times when using, and more so at rest.
Did somebody encounter this problem since upgrading to iOS 10 It is the only variable that has changed, I'm still using the same networks that I have always used for Wifi.
Follow these steps to find and correct the problem:
1. you must check your Wi - Fi router: check if other devices can be connected. This will let you know if there is a problem with your Wi - Fi router. You can restart your router and restart the connection to WiFi.
2. make sure that Wi - Fi on and you can see your network
3. go to settings on your iPhone > Wi - Fi and check if it is enabled. And if there is a blue check mark next to a network name means that your iPhone or iPad was connected to this network.
4 restart your iPhone/iPad, router, cable/DSL mode
5. If this does not help, reset your network. On your iPhone, iPad, got to settings > general > reset > reset network settings. This will reset Wi - Fi networks and passwords, cell parameters and VPN, and APN settings you used before.
These measures should help.
-
Cannot start new iMovie on iPad Air project
Hi, I need to do a project for my university studies, final evaluation. I'm hoping to use iMovie on my iPad Air, as I have done so successfully in the past.
This week, I'm in iMovie and click the symbol +. Then I click on the option to create a new project or a trailer. But when I click on one of these options, nothing happens. If I click Cancel, nothing happens and the application crashes. I have to then close and reopen the app.
Look at a last projects is not a problem.
Indices received with gratitude. I wonder if it's because I recently upgraded to iOs.
iMovie has been updated for iOS 10. Make sure you have the latest version installed.
-
I feel a little brain locked with dropbox on my mac air. I was running out of space and cannot say if the 150 GB on my dropbox folder actually takes this amount of room
on my HD, I tried the DB docs and cannot understand it.
of course, it does not take place timm on my iphone even if I can access all the files on my phone.
does anyone know how it works and how I would keep some data too much HD space if she does not take place?
THANKS FOR ANY HELP
If you put something in your Dropbox storage space, then you can remove it from the computer. If you do not remove it from the computer, then it occupies space on your SSD as well as in your Dropbox storage space.
-
I have an Iwatch is the first gen however updated to ios 3.0, I also have a MacBook Air, which is a 2015. I only got about 4 months. I downloaded Sierra and was very excited on my watch unlock my mac. However, it will not work.
I did every step very carefully this Apple support suggested, I spent 2 h 30 in the store with a genius and it still does not work. I was on the phone with Apple support and hung up, so Im hoping to get some help here.
Hey Molly624,
If I understand correctly, you have trouble getting the Apple Watch to unlock your MacBook Air. It seems that you have already done some troubleshooting and you have perhaps already been through this material, but just in case I recommend to read this article. He hs the steps and requirements for this feature.
Automatically unlock your Mac with your Apple Watch
Thank you for using communities of Apple Support. Have a good.
-
10 do iPad iOS 2 Air running slow
After the upgrade to iOS 10, I noticed my iPad 2 Air starts to run slowly. I mean by "slowly" as slow as my old iPad Mini 2 ran on iOS 9. It is a huge problem, and I'd rather not buy a new iPad. Any ideas?
Hi MBCollector672,
Thank you for using communities Support from Apple. Sorry to hear you're having this problem with your iPad 2 Air. I'm kinda not clear about the exact nature of the slowness you describe (what specific aspects are slow, what is compatible or intermittent, etc.), but if it's pretty repetitive, you can try to stop all currently open applications, restart your iPad, then test for the slow pace. You can find the following articles useful:
Force an application to close on your iPhone, iPad or iPod touch - Apple Support
Restart your iPhone, iPad or iPod touch - Apple Support
You can also see if applications consume an amount unusual or unexpected autonomy. Applications that do are often "stuck" in the background, consuming the CPU power (and thus battery), which can lead to slow overall system. This article may also be useful:
On the use of the battery on your iPhone, iPad and iPod touch - Apple Support
Kind regards.
-
MacBook air crashes after the release of sleep since the upgrade of the sierra
Began to notice that since I upgraded my macbook air 2015 to sierra, system crashes. The trigger is always when I wake the sleep system (whether it is by opening cover or press a key). Issue is intermittent and may not be reproduced every time. I contacted apple support and they recommended resetting the SMC (ctrl + shift + cmd) but that didn't help either. I also did a check of filesystem (fsck-fy) and which seems to be very well so.
I noticed others seem to be faced with similar problems and a common theme that I noticed was that both we seem to have an installed tardisk. Not sure if this could be a factor?
While it is not any loss of data, the question is certainly annoying and disruptive to work.
The same question was observed at about 7 times since the update of the sierra. Containing the report of Etrecheck to the breast
# Date and time 1 Kills Sep 28 10:03:09 2016 2 Kills Sep 28 18:13:50 2016 3 Fri 30 Sep 11:49:16 2016 4 1 Oct 01:05:15 Sam 2016 5 Mon 3 Oct 08:05:42 2016 6 Mar 4 14:26:03 Oct 2016 7 Sea 5 Oct 11:19:17 2016 Sea 5 Oct 11:19:17 2016
Panic report *.
panic (the appellant 2 0xffffff8004f7316e cpu): initproc is out - output namespace 2 subcode 0xa description reason: no
News of the UUID:
0 x 101425000 uuid = < a525eaea-af86-30c2-b360-3d093b4f0828 >
0 x 100713000 uuid = < 268e1319-a81e-384a-9303-67c26873038a >
Thread 3 crashed
RAX: 0 X 0000000000002210, RBX: 0X00007FFFE358C314 RCX: 0X0000700000F06BDB RDX: 0X000000010075DD1E
RER: 0X0000700000F06B30, RBP: 0X0000700000F06B70, IHR: 0X000000010075C698, RDI: 0X0000700000F06BDC
R8: 0X0000700000F06BD0, R9: 0X0000700000F06BCC, R10: 0 X 0000000004001080, R11: 0 X 0000000100756188
R12: 0X000000010075E8A8, R13: 0X0000700000F06BCC, R14: 0X0000700000F06BDC R15: 0X000000010075C698
RFL: 0 X 0000000000010283, RIP: 0X000000010143B605, CS: 0X000000000000002B, SS: 0 X 0000000000000023
Thread 0: 0xffffff80108dcdc8
0x00007fffe36b7456
Could not read the context 0x0000700000e01cd8 LR
Thread 1: 0xffffff80108e1748
0x00007fffe36bf27e
0x00007fffe3568337
0 x 0000000000000000
Thread 2: 0xffffff801558e6f8
0x00007fffe37a6214
3 wire: 0xffffff80159b8028
0x000000010143b605
0x0000000101441c7e
0x00000001014297ad
0x00007fffe358c48e
0 x 0000000100756188
0x00000001007265f3
0x0000000100725ef8
0x00000001007291cb
0x00007fffe355a128
0x00007fffe356fc10
0x00007fffe3565ad2
0x00007fffe355c966
0x00007fffe35709d2
0x00007fffe3562d41
0x00007fffe35713bf
0x00007fffe35741b0
0x00007fffe37a661f
0x00007fffe37a6221
0 x 0000000042000000
Thread 4: 0xffffff80151f4260
0x00007fffe36bf4e6
0x00007fffe37a6221
0 x 0000000000000000
Wire 5: 0xffffff8015c45e18
0x00007fffe37a6214
Mac OS version: 16A 323
Kernel version: kernel Darwin in Version 16.0.0: Mon Aug 29 17:56:20 PDT 2016; root:XNU-3789.1.32~3/RELEASE_X86_64
Kernel UUID: 622D2470-C34D-31F9-A62B-6AA9A3C6A3CD
Name of system model: MacBookAir7, 2 (Mac-937CB26E2E02BB01)
******************************************************************************** *******************************************************
Mar 4 14:26:03 Oct 2016
Panic report *.
panic (cpu 1 0xffffff801817316e appellant): initproc is out - output namespace 2 subcode 0xa description reason: no
News of the UUID:
0x1065e4000 uuid = < a525eaea-af86-30c2-b360-3d093b4f0828 >
0x1055df000 uuid = < 268e1319-a81e-384a-9303-67c26873038a >
Thread 3 crashed
RAX: 0 X 0000000000000000, RBX: 0000000000000078 RCX 0 X: 0 X 0000000000000000, RDX: 0X000000000000007D
RER: 0X00007000061AC868, RBP: 0X00007000061ACCD0, IHR: 0X00007FDF61717C40, RDI: 0X00007000061AC888
R8: 0 X 0000000000000040, R9: 0X00007FFFE56873D0, R10: 0XFFFFFFFFFFFFFFFF, R11: 0 X 0000000000012068
R12: 0X00007FFFE5688148, R13: 0X00007FDF6160FAB4, R14: 0X00007000061ACCF0 R15: 0X00007FDF6160FAA0
RFL: 0 X 0000000000010206, RIP: 0X00007FFFDB52C00E, CS: 0X000000000000002B, SS: 0 X 0000000000000023
Thread 0: 0xffffff8023eb2be0
0x00007fffdcad2456
Could not read the context 0x0000700005fa0cd8 LR
Thread 1: 0xffffff8023eae260
0x00007fffdcada27e
0x00007fffdc983337
0 x 0000000000000000
Thread 2: 0xffffff802669e498
0x00007fffdcada4e6
0x00007fffdcbc1221
0 x 0000000042000000
3 wire: 0xffffff8027112260
0x00007fffdb52c00e
0x000000010561051d
0x00007fffdc975128
0x00007fffdc98ac10
0x00007fffdc980ad2
0x00007fffdc977966
0x00007fffdc976ee0
0x00007fffdc976cb7
0x00007fffdcbc1746
0x00007fffdcbc1221
0 x 0000000000000000
Thread 4: 0xffffff802538d510
0x00007fffdcbc1214
Wire 5: 0xffffff802538abb8
0x00007fffdcbc1214
Mac OS version: 16A 323
Kernel version: kernel Darwin in Version 16.0.0: Mon Aug 29 17:56:20 PDT 2016; root:XNU-3789.1.32~3/RELEASE_X86_64
Kernel UUID: 622D2470-C34D-31F9-A62B-6AA9A3C6A3CD
Name of system model: MacBookAir7, 2 (Mac-937CB26E2E02BB01)
******************************************************************************** *******
Report Etrecheck
EtreCheck version: 3.0.6 (315)
Report generated 2016-10-05 18:58:11
Download EtreCheck from https://etrecheck.com
Time 02:31
Performance: Excellent
Click the [Support] links to help with non-Apple products.
Click [details] for more information on this line.
Problem: Computer restarts
Description:
System of maintains restart with an error "panic (appellant 2 0xffffff8004f7316e cpu)": initproc is out - output namespace 2 subcode 0xa description reason: no ".
MacBook Air (13 inch, early 2015)
[Data sheet] - [User Guide] - [warranty & Service]
MacBook Air - model: MacBookAir7, 2
1 processor 1.6 GHz Intel Core i5: 2 strands
4 GB RAM not extensible
BANK 0/DIMM0
OK 2 GB DDR3 1600 MHz
BANK 1/DIMM0
OK 2 GB DDR3 1600 MHz
Bluetooth: Good - transfer/Airdrop2 taken in charge
Wireless: en0: 802.11 a/b/g/n/ac
Battery: Health = Normal - Cycle count = 76
Intel HD 6000 graphics card
Color LCD 1440 x 900
macOS Sierra 10.12 (A 16, 323) - since the starting time: 6 hours
SM0256G SSD APPLE disk0: (251 GB) (Solid State - TRIM: Yes)
EFI (disk0s1) < not mounted >: 210 MB
Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB
Mac 500 GB internal (disk2) / [Startup]: 505,01 (Go 343,25 free)
Encrypted AES - XTS unlocked
Storage of carrots: disk0s2 250.14 GB Online
Storage of carrots: disk1s2 255,52 GB Online
Card reader Apple
Apple Inc. BRCM20702 hub.
Apple Inc. Bluetooth USB host controller.
Apple Inc. Thunderbolt_bus.
Mac App Store and identified developers
~/Library/LaunchAgents/com.example.restart.plist
sh - c ~/Desktop/TarDiskPear.app/Contents/MacOS/TarDiskPear
A unknown file found. [Check files]
/Applications/Kies.app
com.devguru.driver.SamsungACMControl [no charge] (1.4.31 - 10.6 SDK - 2016-03-01) [Support]
com.devguru.driver.SamsungACMData [no charge] (1.4.31 - 10.6 SDK - 2016-03-01) [Support]
com.devguru.driver.SamsungComposite [no charge] (1.4.31 - 10.6 SDK - 2016-03-01) [Support]
com.devguru.driver.SamsungMTP [no charge] (1.4.31 - SDK 10.5 - 2016-03-01) [Support]
com.devguru.driver.SamsungSerial [no charge] (1.4.31 - 10.6 SDK - 2016-03-01) [Support]
/ Applications/Parallels Desktop.app
com.parallels.kext.hypervisor [no charge] (11.2.0). 32581 - SDK 10.9-2016-07-24) [Support]
com.parallels.kext.NetBridge [no charge] (11.2.0). 32581 - SDK 10.9-2016-07-24) [Support]
com.parallels.kext.usbconnect [no charge] (11.2.0). 32581 - SDK 10.9-2016-07-24) [Support]
com.parallels.kext.vnic [no charge] (11.2.0). 32581 - SDK 10.9-2016-07-24) [Support]
/ Library/Application Support/org.pqrs/Karabiner
[loading] org.pqrs.driver.Karabiner (10.20.0 - 10.11 SDK - 2016-06-19) [Support]
[no charge] 7 tasks Apple
[loading] Apple 168 jobs
tasks of Apple 96 [performance]
[no charge] 40 Apple jobs
[loading] 158 jobs Apple
Apple tasks 105 [performance]
[loaded] com.adobe.AAM.Updater - 1.0.plist (2016-07-15) [Support]
[cannot] com.adobe.ARMDCHelper.cc24aef4a1b90ed56a725c38014c95072f92651fb65e1bf9c8e43c37a2 3d420d.plist (2016-07-13) [Support]
[loading] com.google.keystone.agent.plist (2016-08-02) [Support]
[loading] com.oracle.java.Java - Updater.plist (2015-12-25) [Support]
[loading] com.adobe.ARMDC.Communicator.plist (2016-07-13) [Support]
[loading] com.adobe.ARMDC.SMJobBlessHelper.plist (2016-07-13) [Support]
[loading] com.google.keystone.daemon.plist (2016-09-02) [Support]
[loading] com.malwarebytes.HelperTool.plist (2016-09-15) [Support]
[loading] com.microsoft.autoupdate.helpertool.plist (2016-08-03) [Support]
[loading] com.microsoft.office.licensingV2.helper.plist (2016-04-11) [Support]
com.Nalpeiron.NetPro.plist [running] (2016-04-30) [Support]
[loading] com.oracle.java.Helper - Tool.plist (2015-12-25) [Support]
[loaded] org.pqrs.Karabiner.load.plist (2016-06-15) [Support]
[loading] org.wireshark.ChmodBPF.plist (2016-07-15) [Support]
[loading] com.bittorrent.uTorrent.plist (2015-12-26)
[cannot] com.example.restart.plist (2016-07-20)
iTunesHelper Application (/ Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
Agent application of file transfer Android (~/Library/Application Support/Google/Android File transfer/Android File Transfer Agent.app)
XMenu application (/ Applications/XMenu.app)
Carabiner application (/ Applications/Karabiner.app)
Hidden Google Chrome application (/ Applications/Google Chrome.app)
Hidden KiesAgent Application (/ Applications/Kies.app/Contents/MacOS/KiesAgent.app)
fuspredownloader hidden Application (~/Library/Application Support /.) WAS / fuspredownloader.app)
AdobePDFViewerNPAPI: 15.017.20053 - SDK 10.11 (2016-08-03) [Support]
AdobePDFViewer: 15.017.20053 - SDK 10.11 (2016-08-03) [Support]
QuickTime Plugin: 7.7.3 (2016-09-13)
JavaAppletPlugin: Java 8 update 101 build 13 (2016-08-07) check the version of
AdobeAAMDetect: AdobeAAMDetect 1.0.0.0 - SDK 10.6 (2016-07-15) [Support]
MeetingJoinPlugin: Unknown - SDK 10.2 (2016-09-28) [Support]
tblive-4: unknown (2016-10-03)
Adblock more - Eyeo GmbH - https://adblockplus.org/ (2016-09-28)
iTube Studio - iSkysoft Studio - http://www.iskysoft.com (2016-07-19)
Open in Internet Explorer - Parallels - http://www.Parallels.com/fr/ (2016-07-24)
Java (2016-08-07) [Support]
Automatic backup: YES
Volumes to back up:
Mac 500 GB internal: disc size: 505,01 GB disc used: 161,76 GB
Destinations:
TOSHIBA EXT [Local]
Total size: 1.00 TB
Total number of backups: 17
An older backup: 24/01/16, 02:55
Last backup: 22/09/16, 17:07
Size of backup drive: adequate
Backup size 1.00 TB > (disc 161,76 GB X 3)
18% Google Chrome Helper (8)
8% WindowServer
6% mdworker (15)
5% of Google Chrome
3% kernel_task
Top of page process of memory: ⓘ
Google Chrome Helper 655 MB (8)
631 MB kernel_task
Mdworker (15) 201 MB
119 MB Google Chrome
Console 111 MB
49MO RAM free
3.95 GB used RAM (647 MB cache)
2 MB used Swap
October 5, 2016, 18:42:55 ~/Library/Logs/DiagnosticReports/QuickLookSatellite_2016-10-05-184255_[redacted] .crash
/ System/Library/Frameworks/QuickLook.framework/Versions/A/Resources/quicklookd. e app/Contents/XPCServices/QuickLookSatellite.xpc/Contents/MacOS/QuickLookSatellit
5 October 2016, 12:43:53 self-test - spent
October 5, 2016, 11:19:17 /Library/Logs/DiagnosticReports/Kernel_2016-10-05-111917_[redacted].panic [details]
October 5, 2016, 11:02:31 AM/Library/Logs/DiagnosticReports/Microsoft Outlook_2016-10-05-110231_ [redacted].cpu_resource.diag [details]
/ Applications/Microsoft Outlook Outlook.app/Contents/MacOS/Microsoft
October 4, 2016, 14:26:04 /Library/Logs/DiagnosticReports/Kernel_2016-10-04-142604_[redacted].panic [details]
October 4, 2016, 10:31:37 AM/Library/Logs/DiagnosticReports/Microsoft Outlook_2016-10-04-103137_ [redacted].cpu_resource.diag [details]
3 October 2016, 11:50:06 AM/Library/Logs/DiagnosticReports/Installer Progress_2016-10-03-115006_ [redacted] .crash
com.apple.Installer-Progress-System/Library/CoreServices/installateur Progress.app/Contents/MacOS/Installer progress
3 October 2016, 08:23:05 AM/Library/Logs/DiagnosticReports/Microsoft Outlook_2016-10-03-082305_ [redacted].cpu_resource.diag [details]
3 October 2016, 08:05:42 /Library/Logs/DiagnosticReports/Kernel_2016-10-03-080542_[redacted].panic [details]
October 1, 2016, 01:05:15 /Library/Logs/DiagnosticReports/Kernel_2016-10-01-010515_[redacted].panic [details]
September 30, 2016, 11:49:17 /Library/Logs/DiagnosticReports/Kernel_2016-09-30-114917_[redacted].panic [details]
September 28, 2016, 18:13:50 /Library/Logs/DiagnosticReports/Kernel_2016-09-28-181350_[redacted].panic [details]
September 28, 2016, 10:03:09 /Library/Logs/DiagnosticReports/Kernel_2016-09-28-100309_[redacted].panic [details]
If you have Bluetooth enabled, turn it off before going to sleep the computer.
-
Failed to bind e-mail, 10 0 2. iPad 2 Air
After installing upgrade 10 0 2 on iPad Air, by clicking on the links e-mail sometimes sends me to my favorites instead of the correct destination page. Why?
Hello. Probably because the link does not. If you copy the link, can you open it in Safari?
-
My macbook air 13 "(2015) is very slow, even after a clean install"
Hello
I have a macbook air 13 "from 2015 and it is VERY slow. I did a clean install from scratch of El Capitan (10.11.06) and always very slow.
Etrecheck give ' "Performance: poor"»
Is there a hardware problem? or what to do?
Thank you
EtreCheck version: 3.0.6 (315)
Report generated 2016-10-05 10:18:11
Download EtreCheck from https://etrecheck.com
Duration 17:11
Performance: poor
Click the [Support] links to help with non-Apple products.
Click [details] for more information on this line.
Problem: Computer is too slow
Description:
too slow
MacBook Air (13 inch, early 2015)
[Data sheet] - [User Guide] - [warranty & Service]
MacBook Air - model: MacBookAir7, 2
1 1.6 GHz Intel Core i5 CPU: 2 strands
8 GB RAM not extensible
BANK 0/DIMM0
OK 4 GB DDR3 1600 MHz
BANK 1/DIMM0
OK 4 GB DDR3 1600 MHz
Bluetooth: Good - transfer/Airdrop2 taken in charge
Wireless: en0: 802.11 a/b/g/n/ac
Battery: Health = Normal - Cycle count = 40
Intel HD 6000 graphics card
Color LCD 1440 x 900
OS X El Capitan 10.11.6 (15-1004) - since startup time: less than an hour
SM0128G SSD APPLE disk0: (121,33 GB) (Solid State - TRIM: Yes)
EFI (disk0s1) < not mounted >: 210 MB
Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB
Macintosh HD (disk 1) / [Startup]: 120,10 (Go 104.05 free)
Storage of carrots: disk0s2 120.47 GB Online
Apple Inc. BRCM20702 hub.
Apple Inc. Bluetooth USB host controller.
Apple Inc. Thunderbolt_bus.
Mac App Store and identified developers
[no charge] 6 tasks Apple
tasks of Apple 166 [loading]
[running] Apple 58 jobs
[killed] 9 tasks of Apple
9 killed process lack of RAM
[no charge] 47 Apple jobs
[loading] 158 jobs Apple
[running] Apple 77 jobs
[killed] 8 tasks of Apple
8 killed process lack of RAM
[loading] com.macpaw.CleanMyMac3.Agent.plist (2016-10-04) [Support]
[loading] com.bittorrent.uTorrent.plist (2016-10-04)
[loading] com.macpaw.CleanMyMac3.Scheduler.plist (2016-10-05)
iTunesHelper program (/ Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
uTorrent program (/ Applications/uTorrent.app)
CleanMyMac 3 Menu program (/ Applications/CleanMyMac 3.app/Contents/MacOS/CleanMyMac 3 Menu.app)
Default browser: 601 - SDK 10.11 (2016-09-03)
QuickTime Plugin: 7.7.3 (2016-07-09)
None
Time Machine not configured!
14% WindowServer
4% kernel_task
0% SystemUIServer
0% cloudpaird
Top of page process of memory: ⓘ
670 MB kernel_task
Mdworker (11) 188 MB
Com.apple.CommerceKit.TransactionService (2) 41 MB
Finder 41 MB
Mds_stores 33 MB
5.02 GB of free RAM
2.98 used GB RAM (1.82 GB being cached)
40 MB used Swap
5 October 2016, 09:38:39 test - passed
Hello, have you tried to reset the management system (SCM) controller on your Mac - Apple Support?
-
MacBook Air (13 inch, mid-2012) autonomy
Hi all
I have a question for those who currently own a mid-2012 13 - inch MacBook Air.
How long does work on a single charge while working with Google Docs on Safari, having several other tabs open and listen to music from Apple? I am interested in real data, not the specifications of the Apple Web site.
Thanks in advance!
Anyone?
Maybe you are looking for
-
How to speed up the process of updating after clean install
original title: updates after a clean install I just performed a facility clean my machine that runs Vista Home Basic Edition and is now trying to download all the updates it has had over the past three years (ex-factory). However it will slowly (no
-
Dump memory blue screen BCCode: d1
configuration - hp m9760in windows vista 4 GB ram Signature of the problem Problem event name: BlueScreen The system version: 6.0.6002.2.2.0.768.3 Locale ID: 16393 Files helping to describe the problem (some files may be is no longer available) Mini0
-
Distribute an application outside of BlackBerry App World
Hi people, I have a BlackBerry 10 app I want to distribute to people until it's available on BlackBerry App World. Is this possible to do? If so, how are you going to do? What is also simple to send the file from the bar, or what I need to do some
-
Hello Recently, I have increased the physical memory on my laptop to 8 GB. However, it seems that only 4 GB is available to the operating system (Windows Vista Business 64). The integrated graphics (Intel 4 Series Express) employs about 4 GB. How c
-
I have some serious issues update to existing and new to download applications.
Hello I just bought a laptop with w8 I have some serious issues update to existing and new to download applications. When I click to download an app it still works but does not settle anything. at this point, I can't click the back (arrow) button to