Allow access to a single host separate interface on the inside of the interface

Similar Questions

• VPN for PIX 515 allowing access to a single host

  I have already setup on my PIX 515 a VPN connection, which allows the user to connect to our network via a cisco VPN client to access network resources.

  I want to configure now is an another VPN connection that external users can use but would only allow access to a host.

  E.g. I would like to VPN in my site but would be allowed to access the 10.1.1.1 on my network.

  How can I do this? What I have to install VPNGROUP another and somehow an access list to allow only traffic to a host of configuration. Can anyone help with the correct syntax for the PIX.

  Thank you

  Scott

  You will now have a bunch of commands "vpngroup" in your PIX, simply go into config mode and add more commands 'vpngroup' but with a different groupname. The VPN client then uses this group name to connect to the PIX.

  Another way to allow only access to a host for this PIX is to split tunnelling on this group, as well as in the tunnel of split ACL set only as a host.

• 160N not allowing access to a single ip address please!

  My router does not allow access to a single ip address.  I have a site that I have ftp access to and everything was working fine until today.  I can't access ftp with all the software and the site will not be rendered.  I checked all implement.  I called the hosting company, ISP provider and is not on their end.  I went to another computer somewhere else and everything worked fine.  I hooked in directly to the modem and everything worked as it is supposed to.  All other websites work very well.  It must be the router.   I have reset the router to factory settings and set to update the firmware.  As I said, everything was working just fine and then suddenly everything that is on the IP 1 will not work.  Any help with my situation is appreciated.

  Since you have already reset your router and re-configured all the settings in this topic. When your computer is connected to the Linksys router, on your computer, open the window command prompt and try to ping the IP address that you're trying to make it work with your Linksys router and check if you have all the answers.

  If not then on your configuration page of the router, click on the Security tab and disable the SPI Firewall and uncheck "Filter anonymous Internet requests" and click on save settings...

  Once you are done with these settings, you can now try to ping the IP address and check if you have all the answers...

  NOTE: Turn off the firewall and Antivirus on your computer...

• What host I must allow access in order to disable adobe products and reagents

  We try to Michael and reactivates an adobe product from one client to the next machine.

  It seems that the feature for uninstalling adobe does not use the internet connection settings and try to connect directly.

  I need to know the host name, so I can put a ruler on my sophos UTM firewall to allow access to that effect

  You can check the Adobe Creative cloud network endpoints here. I hope this helps.

• Allow access to the right Information

  Hello

  We have a business account and we created a folio with overlay Web Content when the option "Allow access to right Information" has been selected. The HTML code provided has a custom JavaScript API based on the Adobe DPS - library and store SDK 2.29.

  We have an iPad with direct payment application, which also uses the Adobe DPS - library and store SDK. When I connect to this application, I can download folios.

  If I open the folio I can't access right information through the library and SDK store in the Web content overlay.

  For example, the adobeDPS.version variable returns the correct version of the LibraryAPI Interface, which means that the API has already been initialized, but the adobeDPS - AuthenticationService.isUserAuthenticated variable is still false, if the variable adobeDPS.deviceService.isOnline.

  • adobeDPS.version is 1.3
  • adobeDPS.deviceService.deviceId has the value null
  • adobeDPS.deviceService.deviceName has the value null
  • adobeDPS.deviceService.isOnline has the value of false

  

  You must use the read API, http://www.adobe.com/go/dps-reading-api, leave in a folio. AuthenticationService unfortunately isn't available from the read API. You can test again with the read API?

• Is it posible to allow access between the host and virtal machine without wired network?

  I want to use my laptop to show him that I did in the virtual work to other people at my home.

  However, the laptop is ofen not allowed access to the network in their office.

  Is it posible to allow access between the host and virtal machine without wired network?

  VMware player

  My virtual machine is filled to the physical network adapter and use the static IP address.

  Brad

  Setting of the virtual machine: filled

  Change that to each host only (what Continuum called VMnet1) or NAT (VMnet8).  Both use a separate virtual NETWORK card to connect the physical computer virtual host, independent of any NETWORK adapter on the host.

  ... Since the machine host (win7) could not get IP, ping fail to VM (192.168.1.5)...

  Because the connection between the guest and the host is through a separate NETWORK card, you must use the 'other' IP address.  Access a prompt on the host computer and type IPCONFIG to view the IP address of VMnet1 and VMnet8 NIC.  Then use this IP address instead of 192.168.1.5.

  And when you have changed the network management modes (i.e. of bridged to host-only), Windows does not automatically renew its IP address.  The virtual NETWORK card uses a different subnet if you need to renew your DHCP lease or change your static IP address to work with the new subnet.

• Allowing access to ESXi host to other subnets

  Hi all

  I use the free version of ESXi and it is in course running on the network. 10.32.125.x I noticed that if I try to connect to the host via the Client vSphere from another network, such as 10.32.126.x, I can't.  I can't ping or SSH host either form the 10.32.126.x network.  All right if I'm on the 10.32.125.x network, which is the same network that the server is running on (10.32.125.63 is the IP host address).  I can access services on thin virtual machines from other networks, just not the ESXi host itself.

  Any ideas of how I can allow access of networks other than that on which lives on ESXi?

  Thank you

  Hello

  You try to access your client vSphere ESXi host, make sure that your DNS and default gateway are defined and correct? Is your default gateway on the ESXi host on your router?

• External access to a single server Via VPN

  Hello

  I borrowed from a router (878) customers using the VPN Client, they can access what they need in their own country.

  A new requirment has developed, there is a hosted server that has IP restrictions so that only a range of internal addresses can be accessed.

  The question is when the VPN client is connected and it picks up an internal address, how do I allow access of an upside to a host. I had thought of split tunneling, but the connection must come from the internal lan and in this case, this does not seem that it will work. There is that a single Internet connection, there is no proxy internally I could use.

  Will this work? If Yes, what is the best way to solve this problem.

  Thank you

  I'll have to look my docs, but I'm sure that I have an example... in any case, here's some info

  Do split tunneling and enter this pool to server traffic to that

  then your outside I based source direct all traffic pool ip to ip loopback public server using the command set routing interface

  and then classify this internal closure in making ip nat inside for something of this interface will be natted / patted your ip of the interface and now your server he will recognize

  hope this helps

  split extended IP access list

  permit

  permit

  -------

  for the route map

  list of IP - vpn access scope

  ip licensing

  ip licensing

  vpn route map

  correspond to acl vpn

  set interface loopback0

  int loopback0

  IP address

  IP nat inside

  include ip pool to server traffic in the nat ACL

  -------------------

  If it's difficult, please paste your config that I'll try to put it into effect

• Not affected by Macintosh computers allow access control rules

  Last week my company revised their policies to become compliant hitrust. As part of this compliance will be to lock the network to avoid data loss. Also among the subisdaries is a bit away from what they are a marketing agency and must continue to do business as usual with custromer data and customer interface using web sites and services that need to be blocked.

  So to answer the marketing department, I've created allows the rules higher in the access list bypass essentially content which is now blocked large company. These rules tested OK using a windows pc, but I never imagined that the macintosh behave differently.

  To deal with the current administration, I created security groups in AD and added users to every function that the waiver has been approved for their Department. In the rules allow, I added the security group to each correspondent allowed access.

  What eventually comes past users on windows computers obtained their exemption through the rules allow, but macintosh users continued to be blocked by the large block of company rule. I then tried the ad user account name and same IP addess machine without success.

  My question is: is - anyone else in the community to come against this same question with their Macintosh and or does anyone have an idea to get these Macintosh computers for the rules of the game so to speak?

  To give you an idea of what is happening in sourcefire is not on a user with the IP address and mac Macintosh

  The facebook of sourcefire stuck on this 10.40.2.20 IP address.

  When I looked it up, it came withoutcurrent user.

  I've attached a screenshot of the host profile if anyone cares to take a look.

  Thanks a bunch...

  Hello

  MAC user can not be part of the windows domain. Have you integrated MAC for authentication AD? I've seen some messages on the internet about it, but I don't know if. I don't think this works for MAC users. The main thing is, user needs to be authenticated from AD and a logon event must be generated on AD (I think 4624). Bed user agent this event and then informs the CMF and that's how FMC learns on the mapping of the ip user.

  Thank you

  Dinkar

• Allow access to the internal area

  Hello

  I'm a consultant that I need to allow access through our PIX. We have a box on our internal network, it needs to be able to configure. I was thinking something like:

  access-list app tcp host 192.178.16.6 host 201.126.22.54 eq 2301

  Access-group app in external interface

  static (inside, outside) tcp 201.126.22.54 10.1.1.112 2301 2301 netmask 255.255.255.255

  consultants address is 192.178.16.6

  Our external address is 201.126.22.54

  Our internal address is 10.1.1.112

  necessary port is 2301

  It looks all right? I'm not exactly sure how would he initially 'connect' to our network... I would think he would use our IP external, correct?

  Looks good, here you have another model.

  acl_out list allowed access host tcp SRC-Public host IP YourPublic eq 2301

  Access-group acl_out in interface outside

  static (inside, outside) 2301 YourPublic-IP IP local 2301 netmask 255.255.255.255 tcp 0 0

  You may need to run a =

  clear xlate

  If you have changed or have changed the static method. Please note that this will reset all the session.

  sincerely

  Patrick

• How to allow access to a local area network behind the cisco vpn client

  Hi, my question is about how to allow access to a local area network behind the cisco vpn client

  With the help of:

  • Cisco 5500 Series Adaptive Security Appliance (ASA) that is running version 8.2 software
  • Cisco VPN Client version 5.0 software

  Cisco VPN client allows to inject a local routes in the routing table Cisco ASA?

  Thank you.

  Hi Vladimir,.

  Unfortunately this is not a supported feature if you connect through the VPN Client. With VPN Client, that the VPN Client can access the VPN Client LAN host/local machine, not host from the local network to business as customer VPN is not designed for access from the local company network, but to the local corporate network.

  If you want to access from your local business to your LAN network, you need to configure LAN-to-LAN tunnel.

• iTunes on pc does not recognize my iphone. the pc does. the iphone asks me to allow access to what I do

  iTunes on pc does not recognize my iphone. the pc does. the iphone asks me to allow access to what I do

  Hello

  Check this help page: If iTunes does not your iPad, iPhone or iPod - Apple Support

• My portfolio is currently configured to allow access when locked. I used to be able to double-click the home button and seems my card and I would enter my access code. I have updated to IOS 10 and I am no longer able to do this.

  My portfolio is currently configured to allow access when locked. I used to be able to double-click the home button and seems my card and I would enter my access code. I have updated to IOS 10 and I am no longer able to do this. All the settings are there. I have an IPhone 6.

  Are? you double click in front of the screen of the iPhone are? (pending). This is what seems to work for me.

  I hope this can help.

• I get a message by signing in iCloud iMac found elsewhere. How can I change the location? How can I get rid of this error message? I allow access from somewhere else (weird)?

  I have iMac OS X version 10.7.5. When you try to connect to my iCloud (I pay for a minimum monthly access), I get the message that my computer is requesting access to iCloud somewhere else. I allow access to this strange place? How can I change my location on the desktop to my address? How can I get my iCloud account?

  Is introduced on the market, two-factor authentication because if this is the case, you will have what is normal - for Apple ID - Apple Support two-factor authentication

• Allow access to the USB Reader under account 'user '.

  Hello world

  Need help to allow access to the usb ports so that users can use a card reader to download stuff on a web application, we have.

  The great way would be able to push on HP device Manager (I v4.5) and Thin Clients are T610 running WES7

  Any help is appreciated.

  See you soon,.

  The local user account is configured to restrict access to the Z:\ only through NoDrives policy.  See http://technet.microsoft.com/en-us/library/cc938267.aspx for more details.

  To make life easier, there are calculators that you can use to determine what should be this entry of 32 bits, based on drive letters you want hidden.  An example is http://www.wisdombay.com/hidedrive/index.php.  The default value for Z:\ is only 0x01ffffff (33554431).