allow only one identity on ISE 1.3
I have ISE 1.3 with a strategy of authentication and authorization with EAP - TLS. Works correctly, but I have seen in the report of authentications, an identity with two different mac address and were authorized by air.
I need allow only an identity with a single device. Because the user copied his certificate on the device and granted access to the network.
Is possilble do this?
ISE does not support restricting an identity to be used only with a single device in this scenario. If your PC are AD registered machines, you can use a computer certificate enlisted by the internal pki with a GPO and set the model certificate to not allow exporting of the private key, then it will not be an easy hack for a normal user to export the certificate (it is possible).
In addition, perhaps ask the user why they do, it might be a valid reason.
Tags: Cisco Security
Similar Questions
-
I bought LR6 and installed cloud creative ok, but when you go to installation of Lr, it allows only one installation of the trial version, the other options are to buy.
Serialize Lightroom trial to activate like Lightroom 6 CC
https://helpx.Adobe.com/Lightroom/KB/serialize-Lightroom-CC-trial-to-activate-as-Lightroom - 6.html
-
Need allow only one of the 2 buttons in a region to answer when returned in a hurry
Hello
Version 4.2 of the apex
Theme: Responsive blue 25
My page has 1 region with a subregion inside. Both regions have a button. When I hit enter it seems that the button of the subregion is one that gets executed. I don't want to do that I want the other button to run. Is this possible?
Also when I google looking for answers to this question, I see references to elements of page apex of a parameter value of ' submit when enter pressed "which can be changed to Yes or no. Simply, I can't find this setting in my articles. Perhaps it has been deleted in the apex 4.2?
Thank you
Steve.
Daggers wrote:
Thanks Scott,.
It's useful information. I turned on debug and I see that my problem is in fact that neither button is presented on enter.
Are you able to tell me where the parameter ' submit when enter pressed "?" is located. I think that's probably the key to my problem.
Steve.
It's in the settings section of the element. However, it is only available on the text elements and the password.
-
Gradient tool allows only one side?
I'm putting an edge faded on my picture. I use the gradient tool. I have the selected layer and you have added a mask. With the selected master, I draw the gradient tool of border for about 1 inch. Then, I go to the next side and repeat the process. After I drew the second gradient, one disappears. So I can't draw a gradient on all four sides. I settings on the normal mix, 100% opacity and have checked the dithering and transparency. I work in CS5 MAC 10.6 x. I used the tool degraded for this simple process before and cannot determine what setting has been done which limit myself to the use of a gradient on 1 side only. Help
Use black to transparent gradient, not the black and white gradient.
-
Traffic permitted only one-way for VPN-connected computers
Hello
I currently have an ASA 5505. I put up as a remote SSL VPN access. My computers can connect to the VPN very well. They just cannot access the internal network (192.168.250.0). They cannot ping the inside interface of the ASA, nor any of the machines. It seems that all traffic is blocked for them. The strange thing is that when someone is connected to the VPN, I can ping this ASA VPN connection machine and other machines inside the LAN. It seems that the traffic allows only one way. I messed up with ACL with nothing doesn't. Any suggestions please?
Pool DHCP-192.168.250.20 - 50--> for LAN
Pool VPN: 192.168.250.100 and 192.168.250.101
Outside interface to get the modem DHCP
The inside interface: 192.168.1.1
Courses Running Config:
: Saved
:
ASA Version 8.2 (5)
!
hostname HardmanASA
activate the password # encrypted
passwd # encrypted
names of
!
interface Ethernet0/0
switchport access vlan 20
!
interface Ethernet0/1
switchport access vlan 10
!
interface Ethernet0/2
switchport access vlan 10
!
interface Ethernet0/3
Shutdown
!
interface Ethernet0/4
Shutdown
!
interface Ethernet0/5
Shutdown
!
interface Ethernet0/6
Shutdown
!
interface Ethernet0/7
switchport access vlan 10
!
interface Vlan1
No nameif
no level of security
no ip address
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.250.1 255.255.255.0
!
interface Vlan20
nameif outside
security-level 0
IP address dhcp setroute
!
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
pager lines 24
Within 1500 MTU
Outside 1500 MTU
mask 192.168.250.100 - 192.168.250.101 255.255.255.0 IP local pool VPN_Pool
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global interface 10 (external)
NAT (inside) 10 192.168.250.0 255.255.255.0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.250.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Telnet timeout 5
SSH 192.168.250.0 255.255.255.0 inside
SSH timeout 5
SSH version 2
Console timeout 0
dhcpd dns 8.8.8.8
!
dhcpd address 192.168.250.20 - 192.168.250.50 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2 image
Picture disk0:/anyconnect-linux-2.5.2014-k9.pkg 3 SVC
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
value of server DNS 8.8.8.8
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
tunnel-group AnyConnect type remote access
tunnel-group AnyConnect General attributes
address pool VPN_Pool
tunnel-group AnyConnect webvpn-attributes
enable AnyConnect group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:30fadff4b400e42e73e17167828e046f
: end
Hello
No worries
As we change the config I would do as well as possible.
First, it is strongly recommended to use a different range of IP addresses for VPN clients and the internal network
No VPN_Pool 192.168.250.100 - 192.168.250.101 255.255.255.0 ip local pool mask
mask 192.168.251.100 - 192.168.251.101 255.255.255.0 IP local pool VPN_Pool
NAT_0 ip 192.168.250.0 access list allow 255.255.255.0 192.168.251.0 255.255.255.0
NAT (inside) 0-list of access NAT_0
Then give it a try and it work note this post hehe
-
seems I'm not the only one having problems with safari after update 9.3 cannot follow the links. Safari blocks. hope it gets fixed quickly. jaa shooting allows to follow the link, but the Web page is not out of good old days. any oher ideas?
The 'list' of relevant articles that I know, they are now
-You can read about the problems in the present statutes and possibly find workaround solutions, particularly in the last
Apple iOS suspension 9.3 updates for older devices, work on activation fix | IVous
Apple launches new version of iOS for iPad users 9.3 2 affected by bricking bug | 9to5Mac
If you are unable to activate your iPad 2 (GSM model) update to iOS 9.3 - Apple Support
Leave a post by: ChitlinsCC
-
Allow only smartphones via anyconnect
Is this possible? The goal is to allow only smartphones/tablets; No full blown laptop os'.
If you have the anyconnect essentials and the mobile anyconnect license would it as simple as ordering "no anyconnect essentials". According to the docs this only disables anyconnect essentials, but leaves the license intact. I hope that this would mean that the anyconnect for mobile would continue to operate. Or maybe there's another way to do this?
Unfortunately I do not have the freedom to test and cannot find it in the documentation.
~ Thank you
"no anyconnect essentials" disables this feature of license for the AnyConnect Premium license.
AnyConnect for Mobile requires one or the other license to operate.
To apply a restriction of device type, you would normally use Dynamic Access Policy (with AnyConnect Premium) and the Cisco Secure Desktop feature. However, CSD is only supported on Windows / OS X / Linux. (Example)
Another way, you could do it would be with the device certificates. Check endpoints for the presence of a certificate (which you would need to deploy) and only allow valid wallet certificate devices to be authenticated. That's how it is (among other things) with Cisco ISE. ISE relieves the pain somewhat by deploying the certificate under the device / user integration. Do it with only ASA, should allows you to use a deployment of certificate 3rd party (or possibly PEIE, but I don't think that you could argue the mobile device in the CEP inscription).
-
Toshiba Bluetooth stack & motorcycle S805 two profiles - can use only one?
Toshiba Bluetooth stack on IBM T42/Windows 2000 test. Motorola S805/multimedia headset supports two audio A2DP stereo of high quality and HFP used as a helmet.
If I create * only * audio sink profile then I can log in and use the headphones (rather good sound!). If I create * only * a headset profile, then they work well for that, too (not very good sound, but convenient and two-way).
I am able to create two connection profiles by linking it first as an Audio receiver, then the pairing again as a helmet. The two profiles now appear in the Bluetooth settings window. First of all, I confirm that neither the profile is connected. Now when I try to 'connect' to the headset, it "sounds" the helmet. However, when I press the headset button to accept the connection I get the following message:
"Now, connect, please wait."
and then
"Helmets and headphones can not be used simultaneously. Finished using the headphones and then establish a connection.
Now the headset (audio receiver) is connected instead of the helmet!Note that before I tried to connect to the headset there was no link at all (message is wrong). Also note that if there is only one connection profile (headset) then the headset will connect correctly.
I want to be able to move quickly from a helmet (good sound quality for music) and headset (for Skype). Deletion and recreation of the connections are too slow, if Skype sounds while I'm listening to music. (the S805 will automatically switch mode headphones while listening to the music, if the call is from a third device such as a cell phone).
Anyone know if the software can be configured to allow me to do this fast switching between profiles on the same device?
Thank you and best regards,
Jeff in Aloha, OR, USA.
You must use the hands-free profile if it is supported also by your device for VoIP instead of the headset profile!
-
How do you get the screen message appears only one for each case?
Hi friends,
I'm here with another question...
I built a VI that must contain 6 boxes, when a particular check box is selected by the user, it should display a message to the user that the checkbox is enabled.
My problem is: when I select one of the boxes the on-screen message continuously one after the other, even when you press the OK button.
Can someone help me please?
An option button allows only a boolean in it to be active at a time. You see these things all the time. Think about a survey that only lets you select one option.
-
How to allow only .gov Web sites on Windows XP using the installation of the broad-band
How to allow websites .gov only on Windows XP. Use BSNL broadband. Made of internet sharing in LAN.
Concerning
Maton
Hi Matt,
This forum is for MSE who cannot restrict access of Web site you want.
One of the possible methods that comes to mind uses the Parental http://www.windows-help-central.com/parental-controls-in-windows-xp.html may control with Windows Live Family Safety http://explore.live.com/windows-live-family-safety?os=other (according to the version of XP and whether or not you have a workgroup or domain LAN). When you set up, allow *.gov, but reject all other types you can imagine (I don't think there is a way to allow only .gov, but you can exclude most if not all of the other busiest - check domain name registrars to get a list of options). If you use a domain, way to go would be with a custom domain group policy to restrict access on all of the network (except perhaps the server or individuals of special category in Active Directory if you want).
If that is not the case, and I think it might, please repost your question in the following forum to get the expert assistance you need: http://answers.microsoft.com/en-us/windows/forum/windows_xp-networking?page=1&tab=all.
I hope this helps.
Good luck!
-
ACL to allow only FTP - various issues
Asked me to develop a way to connect a server of the company not to one of my closet of 5509 running several VLANS over a couple of floors on my building. The 5509 has no RSM and is connected to the big 3 layer switch... 6509.
I was told that I have to do the "secure" connection This server will make file xfer (probably ftp)
Even if we have a firewall... the decision was taken to put the server in own vlan... say vlan 201 and hard give it an ip address of 10.4.201.11
I learned to develop an ACL that will allow only ftp traffic.
Here's my plan
create a vlan 201 on the 6500 and 5509 and assign a 5509 port to it for the server
I think the application the following ACL to my interface vlan 201 on the 6509.
access-list 100 permit tcp 10.4.201.11 0.0.0.0 no matter what 20 eq
access-list 100 permit tcp 10.4.201.11 0.0.0.0 no matter what eq 21
access-list 100 deny ip any one
On the 6509 applying the ACL
IP access-group 100 to
I have a few questions
1. If I have the ports 20 and 21 licence cover me for ftp traffic?
2. by encoding 0.0.0.0 in the acl that forces ip address of 10.4.201.11 to match or through it now?
3. as far as I know deny it a whole will kill anything else
4. I am concerned by a couple of other things... I don't know that thanks should be sent back as appropriate. I also wonder if I also need to apply leaving and entering?
5. What saddens me really, it's that I have never done an ACL before and do not want to create a situation where I block the other traffic on the 2 switches... I guess that's the advantage to do it in one vlan separate... then I hope that if something "unexpected" happens when we applied it... it would only affect that the vlan 201.
6: last question, if we had to go back for some reason any acl... I hear that they are difficult to change once in the config... A procedure to follow to get rid of the ip access-group 100 in 1st then remove... the fact second access list statements the other way would leave only the list still in the group.
Thanks in advance for any helpful suggestions
Hi Lane,
Here are a few answers (in the same order as your questions)
1. the answer is: it depends. FTP can operate in one of two modes: active and passive. Depending on the mode, the required ports are different. The following URL has a good explanation of the difference between the two;
http://SlackSite.com/other/FTP.html
As the server is under your control, I think that using Active FTP should be fine. Therefore, the two server ports you need to open are tcp/21 and tcp/20.
2. a mask of 0.0.0.0 makes the access list on every bit of the network address that is specified. So what you've got is fine.
3. access lists have all implicit "deny all" at the end of their kind that last statement is not really necessary, but it might be good to let in readability.
4. because you want to make sure, a combination of inbound and outbound filtering is in order.
5. what you do on this VLAN will affect that VLAN and that only one VLAN - you don't have to worry about an impact on anything else.
6. it's okay. Remove the statement of 'ip access-group' under the interface before doing anything to the access list real himself.
Here's how to set up the ACL:
access-list 101 permit tcp any gt 1023 host 10.4.201.11 eq 20
access-list 101 permit tcp any gt 1023 host 10.4.201.11 eq 21
access-list 101 deny an entire
!
access list 102 permit tcp host 10.4.201.11 eq 20 all gt 1023
access list 102 permit tcp host 10.4.201.11 eq 21 all gt 1023
access-list 102 refuse a whole
!
interface vlan201
IP access-group 102 to
IP access-group 101 out
Now, the above lists will be only to let the FTP server and not much else. Your server should use the DNS for some reason any? If so, you will need to drill holes in the ACL above to allow UDP/53 through.
Hope that help - rate pls post if it does.
Paresh
-
We have an important customer who said they don't want their employees who receive emails from marketing except a specific list of their management team. Also, we do not want the employees of our customers who decide to opt-in to receive emails from our registration page if they use their work email address.
How can I allow only a specific list of employees (management team) to receive marketing emails, but exclude all others in the same company?
One way is to create a list of sharing, "company A does not include." Build a program in the program generator with a charger that looks for the domain "company A". Place a filter in the program on a decision rule with the emails to management teams; If they are in the filter (that is, they are on the management team), remove them program, if they are not (that is, they are not the management team), add them to the list of sharing "excludes company A. Then you can add the list of sharing "Company A excludes" as an exclusion on your segments or implement a model that they will automatically as an exclusion.
They oppose all non management team emails? If they are, as an extra precaution, you could add the "exclude company A" to master exclusion list.
-
table is expected to insert only one line
Hi all
my need is to create the table that allows to insert only one line.
How can I make it?
Oracle Database 11 g Enterprise Edition Release 11.2.0.1.0 - 64 bit Production
PL/SQL Release 11.2.0.1.0 - Production
"CORE 11.2.0.1.0 Production."
AMT for Linux: Version 11.2.0.1.0 - Production
NLSRTL Version 11.2.0.1.0 - Production
Hello
2621671 wrote:
Hi all
my need is to create the table that allows to insert only one line.
How can I make it?
Oracle Database 11 g Enterprise Edition Release 11.2.0.1.0 - 64 bit Production
PL/SQL Release 11.2.0.1.0 - Production
"CORE 11.2.0.1.0 Production."
AMT for Linux: Version 11.2.0.1.0 - Production
NLSRTL Version 11.2.0.1.0 - Production
You can create a unique Index based on a function, like this:
CREATE UNIQUE INDEX table_x_u ON table_x (NVL2 (col_1, 1, 1));
You can use any column of any data type. In other words, the function may return a NUMBER, if the column referenced in the function is a NUMBER.
Regardless of whether the column is NULL or not; not more than 1 rank is authorized.
-
I have a file of avchd about 15 min in length on a sdhc card. My camera says there is only one file. When I put the card in the PC (Win8.1), the PC says there are 2 files, a 11mins about and the other is 4 minutes long ago. If I put these files in Prime Minister CS6 they are the two identical length of 15 minutes, what is happening here?
Copy card full hard disk, and then ingest via the media browser.
See if that will make a difference.
-
Please Help - box-only one of them SHOULD BE checked at any time - how?
Hello
I have page apex with regions where I have some text fields of type checkbox. (YES NO)
Problem is that if I click YES and then click NO, YES even 'CASE.
How to avoid this... Whereas If I go YES to ANY box, only one is checked at any time
Thank you
KPA group of Radio buttons is the element that has an exclusive selection. Checkbox allows multiple selections.
See examples: http://apex.oracle.com/pls/apex/f?p=25096:3 Login: Dever PW: Ima9Dever
P. 3 - Group of Radio buttons
P. 4 - box
Maybe you are looking for
-
differences in storage between 5 (A1428) and 5 (A1533)
Hello I recently had to replace my iPhone 5 (A1428) with a 5 (A1533). I was not able to load my backup set on the new iPhone. Because they are the two 16 GB, I'm stumped. It should not be the same? Two iPhones have iOS 9.3.3. I can no longer boot the
-
Hello Last fall, I installed Thunderbird for Windows on my PC. I'm very happy with it and plans to install the version for iOS on my ipad. I wonder if 2 versions would be able to communicate with each other. Specifically, they will be able to: share
-
Satellite A100 PSAA9A: Cannot use fingerprint & keys Fn after the new installation of Vista
Hello I am currently using toshiba A100 PSAA9A initially running a winxp pro sp2.But recently I received a window Vista on the other computer manufacturing so I reformat and installed. But after the installation, I checked all driver devices and they
-
iOS 9.2 causing lag in Logitech Create keyboard for iPad Pro
iOS 9.2 has considerably weakened the Logitech Create keyboard for iPad Pro performance. He had been immediately sensitive - one of the best features that the combo made feel like a laptop. With 9.2 key strokes are interrupted at left and right, and
-
Cannot access my accounts. Cann't backup or restore. Help