Allow to more users through Anyconnect

Similar Questions

• Matter of principle: allow internal VPN users to external networks

  Hi people.

  We receive requests from our internal users, asking the ability/permission to VPN in outside networks businesses of related objectives. They would use our business machines sitting on our corporate network and perhaps required VPN software installation/configuration (for example, Nortel, Microsoft PPTP, IPSec Cisco, etc.) They go out through our ASA Firewall and then connect to the remote network.

  Currently, we block out IPSec and PPTP to avoid this problem, and the reason why we give is that you are connecting two networks and potentially open our internal network up to who knows what.

  In the past we have remote offices install stand-alone DSL lines and ACL acceding to the external VPN, but it becomes expensive and bulky. The same for wireless EVDO cards.

  With the current state of the economy, the price of gas or movement, etc., becomes more difficult to refuse these requests and the higher Up inside are getting hit by operational units.

  How guys do you deal with that? What reasons did you give for allowing / preventing external access VPN? The problem is better solved with the policy or technical (or both?) You poke holes and make exceptions for specific external VPNS, and if so, what are the requirements don't surround you?

  Thanks for any input!

  -Neil

  In the case of IPSec, I'm not sure you fill the two networks.

  You allow traffic be sent through tunnel through your good firewall, and the limits imposed on passenger transport are generally determined by the thrust of policy from the other end of the VPN of parties and any software firewall on your host computer.

  I think it boils down to the protection of the appropriate host on your end, and some common sense as to which the parties, you are allowed to connect too (written policy).

  The Cisco VPN Client provides a built-in firewall and the ability to restrict your host to access the local LAN while the tunnel is UP.

• HP Pavilliona6512p: should I allow telus mobile cdma through the firewall

  . I found that I had an open gate that was puttibg info at risk. Should I allow telus mobile cdma through the firewall?

  Brihayes67, welcome to the forum.

  What I read of Telus CDMA network is closing this year.  If you don't have any use for it, I would not in it.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Windows Mail error 0x800CCC92: Operation of Pop is not allowed for this user

  Split of: ' "windows mail error code: ox800CCC0E, error code 10060".

  Account: 'mail.bigpond', server: 'mail.bigpond.com', Protocol: POP3, server response: '-ERR pop operation is not allowed for this user.', Port: 110, secure (SSL): no, Server error: 0x800CCC90, error number: 0x800CCC92

  It's what keeps appearing on my Windows Mail when I go in there. BigPond say they have problems with Windows Mail and try to fix it.  Any ideas please?

  Thanks LyndaBeresford

  If they have problems, then it is not that you can do about it until they solve these problems.

  You can access your e-mail via webmail: https://signon.bigpond.com/login?site=chw&goto=http%3A%2F%2Fmessaging.bigpond.com%3A80%2F%3Fref%3DNet-Head-Webmail

  Steve

• Allow a standard user to run a program with elevation of the admin.

  I have a program that will run only on admin or with the approval of the admin. I want him to be executed on all users computers with standard users. How can I do this?

  That has never been answered so for those looking for an answer...
  Log in as an administrator and disable UAC
  -> Panel-> accounts user and family safety-> user accounts modify the user account control--> then just slide down never notify.

  This will allow a standard user to access admin and admin stop programs confirm the open each time

• InDesign CS5 for windows only allow me to scroll through the functions with the mouse wheel

  Nice day

  InDesign CS5 for Windows only allow me to scroll through the functions with the mouse wheel and for example not allow me to access drop down menus, any help will be much appreciated

  https://helpx.Adobe.com/InDesign/KB/InDesign-tools-panels-Don ' t - respond.html

• I upgraded to Acrobat Reader Acrobat Reader DC.  I can save is no longer a PDF file.  I can open is more pdfs through IE11.  IE 11 crashes when I try to open a pdf file.  I can preview is no longer a PDF file in Windows Explorer or Outlook 2013.  Outlook

  I upgraded to Acrobat Reader Acrobat Reader DC.  I can save is no longer a PDF file.  I can open is more pdfs through IE11.  IE 11 crashes when I try to open a pdf file.  I can preview is no longer a PDF file in Windows Explorer or Outlook 2013.  Outlook Express crashes and had to be reinstalled once since I installed AA DC.  I tried deleting and reinstalling DC, reset internet IE11 options by default and am running Windows 7.

  Hi paulgriggs1960,

  Uninstall Acrobat Reader DC using tool cleaning Download Adobe Reader and Acrobat tool - Adobe Labs

  Then install Reader using this link: Adobe - Adobe Acrobat Reader DC Distribution and check if it solves your problem.

  Let us know if problem still persists.

  Kind regards

  Meenakshi

• Comments operations are not allowed for anonymous users on this virtual machine

  Hello

  After a lot of trying, I finally managed to connect to a virtual machine in VMware Server 2.0.2

  However, I get the error "comments operations are not allowed for anonymous users on this virtual computer" when I try to run notepad.exe. I think that some permissions must be set. So I put comments and guests of user group to be able to administer the object (VM); but still this error comes.

  Can someone help me pls with getting beyond this error.

  Thank you very much.

  This has come up before on this Forum. Be default, Windows does not allow for remote log-ins for accounts without password, which prevents the VIX to perform log-ins comments in this situation.

  You can follow the steps described in the following thread to enable remote log-ins for accounts without password or change the account to have a password.

  http://communities.VMware.com/message/910606

• How to allow connect to user only from specified ip addresses?

  Hello.
  How to allow connect to user only from specified ip addresses?
  For example,.
  User1 can connect only from 192.168.1.10
  User2 can only connect from 192.168.1.11
  and etc...
  Thank you.

  Web says:

  CREATE OR REPLACE TRIGGER "A1_AFTER_LOGON" AFTER LOGON ON DATABASE BEGIN
  IF UPPER(SYS_CONTEXT('USERENV','IP_ADDRESS')) <> '192.168.1.10' THEN
  
  HOW TO FORBID ACCESS ????
  
  END IF;
  END;
  ALTER TRIGGER "A1_AFTER_LOGON" ENABLE
  

  How to deny access?

  Check the blog post that I've provided above

  RAISE_APPLICATION_ERROR(-20000, 'You don't have permission to login!');
  

• ACS5.2 joined the announcement, allowing the user through internal OK, through AD does not

  Hi all

  My ACS5.2 joined to Active Directory in Windows 2003 with success. I created the support group with user1 in the store internal, also created the Group of support-AD with userad1 in the store AD. Sequency identity store is defined internal first, then AD. I can map Support-Group to the Group of local support without any problem.

  Internal user is authenticated and authorized OK. However, if the user is a user of the AD, the rule for users of the AD is not recovered. So, by default.

  I must have missed something. Help, please. I have uploaded my screenshots. Thanks in advance.

  Robert,

  Something that I found to be very useful for troubleshooting these types of problems in ACS 5.2 is the monitoring and report viewer.  If you start it, and then choose Protocol AAA left under the catalogue, it will present you with several reports, one of them being the RADIUS authentication.  Run the report, and then select the details by clicking on the magnifying glass in one of the entrances leading to the use of the default rule.  The details are very good and will display the results of treatment step by step and when your default rule is being chosen.

  I hope this helps.

  Greg

• Customize the unique user through Office Windows remote connection

  Hello

  I would like to know if its possible to set up Windows so remote desktop if a user is already connected to a particular computer and another user attempts to connect, an error message appears on the screen saying a user is already logged on.

  I can limit the number of connections to 1 through:

  Local Group Policy Editor > templates Admin > Remote Desktop Services > Remote Desktop Session host > connections

  However, with this option, the error message that appears on the screen is as follows:

  "This computer can't connect to the remote computer, try again or contact your network administrator.

  Is it possible to configure this to allow users to know why they cant login so that they do not think its a COMPUTER error?

  We use Windows 7 on clients and the host.

  Any advice would be much appreciated...

  Thank you

  Seema

  Seema Hello,

  Thanks for posting your query in Microsoft Community.

  I understand that you have problems with Windows Remote Desktop on a client's server computer, so I would advice to follow the link mentioned below to post your query in the TechNet forums and see if that helps, because they have more expertise on this issue.

  Forums TechNet for Windows 7
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Hope this information helps.

• GANYMEDE user through the console?

  Hi all

  We had a strange problem with authentication via GANYMEDE. Logging on to a switch via VTY works well... I enter my user name and PW and start at the privileged exec prompt. But when I am trying to connect through the console, I won't get it priviledge rights exec without entering in a passage of the ena. This phenomenon occurs in different versions of IOS.

  Config looks like this:

  AAA new-model

  AAA authentication login default group Ganymede + local

  the AAA authentication enable default group Ganymede + activate

  default AAA authorization exec group Ganymede + none

  AAA authorization network default group Ganymede + local

  AAA accounting send stop-record an authentication failure

  AAA accounting newinfo periodic update 15

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  Default connection accounting AAA power Ganymede group.

  !

  username privilege 15 password

  RADIUS-server host x.x.x.x

  RADIUS-server host x.x.x.x

  RADIUS-server timeout 25

  radius-server key

  Line con 0

  exec-timeout 0 0

  line vty 0 4 aso.

  Any ideas?

  Kind regards

  Sebastian

  Sebastian

  What you are experiencing is a behavior of Cisco implements voluntarily. As has been explained to me, to directly enter mode privilege is a combination of authentication and authorization. For the vty ports it is enabled. For the console, it is the authentication, but not the component of the authorisation. The reason for this is that it is easy to misconfigure the framework for approval of the configuration. It's one thing to lock you into the vty ports and it's something of another (and more serious) If you lock you out of the console. So as a safety mechanism Cisco only default not apply permission on the console. You will need to enter the password to enable on the console.

  HTH

  Rick

• ASA5505 with 10 users. Need to connect 25 remote users with AnyConnect Client

  Hello to everyone.

  I ASA5505 with license 10 users. I need to connect 25 remote users via SSL VPN (in my case cisco Anyconnect client). So I have to buy the license more security (ASA5505-SEC-PL =) for more then 10 simultaneous VPN connections on Cisco ASA 5505. Fix?

  And the main question. What I need to order the user getting up-to-date (for example ASA5505-SW-10-50 =, or ASA5505-SW-10-UL =) license for my device Cisco ASA5505 in order to have 25 connections of concurrent remote users without restriction for each remote user?

  You need the license SecPlus for increased remote access users. But you don't need an extra user license if you still only up to 10 internal systems.

• Allow a virtual browser through firewall?

  I recently worked with a virtualized 19 Firefox version, but I'm having a problem allowing it through the Windows Firewall. The problem is that the executable file itself is buried in the C:\Users\%USERNAME%\AppData\Roaming\VOS\Firefox\%Program Files%\Mozilla Firefox\firefox.exe

  In the path above '%Program Files%' refers to a literal location where the directory is surrounded by % and does not refer to the environment variable. I also use AppLocker and he doesn't have a problem with this way, but firewall appears. Actually move or rename this directory is impossible, because this place is indispensable for the virtual fie system works. So, I need a way to pass this path to the firewall without thinking that the actual path is "C:\Users\%USERNAME%\AppData\Roaming\VOS\Firefox\C:\Program Mozilla Firefox Firefox\firefox.exe".
  So far, tried to escape from the % with ^ and doubling the percent as you, without any result. Enclose the path in ' ' did not help, either. I also tried to use the short name of the directory (% Progr ~ 1), hoping that would help. Finally, I also tried to create an environment variable to point to the path and the addition of the rule in this way, without success. When I try to add the rule manually on the local computer (I am also to push those rules to GP) I get an error that the application path cannot be resolved.
  I hope someone has another idea.

  Update: you can feel free to take the virtual browser completely off the problem. The problem is, how do I switch Windows Firewall with security advanced a rule when the path contains percent signs? I'm learning the syntax to inform the Firewall %Program Files% should not be treated as an environment variable.

  Hello
   
   
  Thanks for joining us out on Microsoft Community Forums.
   
   
  The question you have posted is linked to the virtualized version of Firefox 19; Please post your question in this link for assistance.
  http://social.technet.Microsoft.com/forums/en-us/categories/
   
   
  It will be useful.
  Please let us know if you encounter problems with Windows and we will be happy to

• Allowing non-root users to mount the ISO images in VSphere

  Hello!

  I'm running ESXi 5 on a root server and want my users to be able to mount a local data store ISO images in their respective VMs.

  I created a role to allow them to start/stop/restart etc their VM, that works well. But I am confused as what permissions, I need to define where to allow them to browse and set an ISO for their virtual CD drives. The authorization 'Browse the data store', set for the virtual machine and the server, doesn't really help.

  All ideas are welcome!

  Sorry for the late reply,

  I can choose an ISO local data store and create a new virtual machine with the following privileges on a stand-alone ESXi 5:

  Data store > allocate space

  Data store > Browse Datastore

  Home > operations > reconfigure virtual computer

  Resources > assign virtual machine to the list of resources

  Virtual machine > all (but this could / should be more restrictive)