Alternative name of the ise 1.3 Cisco SAN object

Similar Questions

• Cannot access the ISE-3395-K9 CISCO Web GUI

  Hello

  I can't access the ISE-3395-K9 web gui interface concert 0 with ip address is 192.168.1.10.  I put the ip address of my labtop to 192.168.1.20 and could ping back but am still not able to access them through a direct connection between my labtop to concert interface 0 using one of the supported web browsers.  Any help would be greatly appreciated.

  It is possible that the GUI was configured to restrict access to only certain IPs / subnets. If 192.168.1.x isn't one of them, then you will have access.

  Are you able to connect to the shell via SSH? If so, you should check and confirm that all associated ISE services run by running the following command:

  show the application status ise

  Thank you for evaluating useful messages!

• Name of the PKI trustpoint client?

  I have two routers directly connected to g0/0 R2 R1 g0/0 lab.

  I have IPsec with preshared keys configured and everything works fine.

  I just finished setting up R1 as the CA PKI server and created a better priority isakmp policy to use when certificates are configured finally between R1 and R2.

  My next task is to configure R1 also as client PKI.

  I ran crypto key generate module general key of rsa 512 - everything is good, no problems yet.

  Now I need to create a trustpoint to the CA server and this is my question-

  Can what name be used - which means that what I have to use the same name that the server CA [R1-CA] or any other name of the ol is well?

  My config for R1 below.

  Thank you again once - I will get it working soon - I hope!

  Frank

  R1 #sh run
  start the flash system: c2800nm-advsecurityk9 - mz.151 - 2.T1.bin
  !
  clock timezone IS - 5 0
  summer time clock IS recurring
  !
  IP source-route
  !
  IP cef
  !
  IP TEST domain name. LAB
  IP host 192.168.1.1 R1
  host IP 192.168.1.2 R2
  !
  cryptographic pki R1 - CA server
  database level complete
  name of the issuer cn = R1 - CA UO = Point to point
  EMP flash url database:
  Crypto pki token removal timeout default 0
  !
  Crypto pki trustpoint R1 - CA
  crl revocation checking
  rsakeypair R1 - CA
  !
  R1 - CA crypto pki certificate chain
  certificate ca 01
  3Y82YA98 3Y82YA42 AYY3Y2YA Y2Y2YAYA 3YYDY6Y9 2A 864886 F7YDYAYA Y4Y5YY3Y
  223A2Y3Y AEY6Y355 Y4Y3A3A7 523A2D43 4A2Y4F55 3D5Y6F69 6E742D74 6F2D7Y6F
  696E743Y AEA7YD3A 3Y3A3Y32 363 3335 3835325 HAS A7YD3A33 3A3Y3235 A 3, 333538
  35325A3Y 223A2Y3Y AEY6Y355 Y4Y3A3A7 523A2D43 4A2Y4F55 3D5Y6F69 6E742D74
  6F2D7Y6F 696E743Y 5C3YYDY6 Y92A8648 86F7YDYA YAYAY5YY Y34BYY3Y 48Y24AYY
  B5467D77 A2FYA8A2 YC3ABAFY [not the real key] 8976CBA5 C3522D4F E43629EY
  YC9C5AB8 F397F99F 7E83AYA6 36A2A526 BF2B8552 4A9F4CC3 AAY6EY4F 4B6AE4AD
  Y2Y3YAYY YAA3633Y 6A3YYFY6 Y355ADA3 YAYAFFY4 Y53YY3YA YAFF3YYE Y6Y355AD
  YFYAYAFF Y4Y4Y3Y2 YA863YAF Y6Y355AD 23Y4A83Y A68YA4CE FCCC6448 DFF9B52A
  6BC29CBD BF3DAA93 D6DBAA3Y ADY6Y355 ADYEY4A6 Y4A4CEFC CC6448DF F9B52A6B
  C29CBDBF 3DAA93D6 DBAA3YYD Y6Y92A86 4886F7YD YAYAY4Y5 YYY34AYY 28A92EC2
  AEBYE76D 9A5AA4D2 7529FAA4 B44CC6CB 8773E5EA 894A48E6 E6C6A3B4 598B 8734
  2A32F838 3424DY46 3C74BY6C AAAB8AFD 926YFCAA B5C87AA5 92BC4Y38
  quit smoking
  !
  crypto ISAKMP policy 10
  BA 3des
  Group 2
  !
  crypto ISAKMP policy 20
  BA aes 256
  preshared authentication
  Group 5
  .
  .
  . blah blah blah

  You must use a different name. The trustpoint with the same name is automatically created by CA server and you should not change it.

  cisco1 Server cryptographic pki
  database level complete
  name of the issuer CN = cisco1.cisco.com L = RTP C = US
  CRL life 24
  certificate of life 200
  Life 365 ca-certificate
  CDP - url http://192.168.1.2/cisco1cdp.cisco1.crl
  !
  Crypto pki trustpoint cisco1
  crl revocation checking
  rsakeypair cisco1
  !
  Crypto pki trustpoint test< this="" is="" trustpoint="" which="" is="" used="" for="" get="" cert="" from="" local="" ca="">
  Enrollment url http://192.168.1.2:80
  IP 192.168.1.2
  revocation checking no

  bhnd-7600 #sh cry cert ca
  CA
  Status: available
  Serial number of the certificate: 01
  Use of certificates: Signature
  Issuer:
  CN = cisco1. Cisco.com L = RTP C = US
  Object:
  CN = cisco1. Cisco.com L = RTP C = US
  Validity date:
  start date: 17:34:02 UTC on October 26, 2010
  end date: 17:34:02 UTC on October 26, 2011
  Trustpoints associated: test cisco1

  Certificate
  Object:
  Name: bhnd - 7600.cisco.com
  IP address: 192.168.1.2
  Status: pending
  The key usage: general use
  Application for fingerprint MD5: 439016A 1 EF93250E 5F870E5F 13DAADA3
  Application for a certificate fingerprint SHA1: 26CC73B3 8AECADD0 C5045B45 3BDC0A8F B636451E
  Related Trustpoint: test

• Name of the instance when adding to the library

  It is a huge problem for me then probably the stupidest question in the world.

  When addressing movieclips nested like this: _root.movieclip.movieclip.variable

  
  they need to have a set instance name, otherwise they count as undefined. If I can put it in properties with no problem, but when it the removal of the step and then time (manually or by actionscript) the name of the instance are gone, so I can't address clips nested in action script.

  I do not understand how it will work, because each time I have add a clip by code there is no instance name. The only alternative for me up to now has kept the clip on the stage all the time, just outside the limits or invisible so I can still do things like _root.movieclip.movieclip.variable or _root.movieclip.movieclip.gotoAndStop (2).

  Someone enlighten me please because I can not understand it.

  The purpose of instance names must be able to use the same object library many times and targets each separately... an instance of this object here, an instance of this object, etc...  The name of the instance applies only to an object on the stage.  A library object has no instance name until you assign a while she participated in the film.

  When you attach a movieclip using the AS2 code, you must use the attachMovie() method.  In the arguments for this method is when you set the name of the instance...

  this.attachMovie (id, name, depth)

  The 'name' argument is the name of the instance you code will use to target this instance.  Hostel if your case you will use...

  this.attachMovie (id, "movieclip1",...)

  I intentionally only focusing on the instance of the name, the other arguments you know if all goes well do deal with

• The band multiple @domaine used in user name on the integration of commercials with Cisco ISE?

  Hello

  How to remove multiple domain suffixes through ISE with AD user name used as an external identity Source. Username is used in [email protected] / * / format.

  Cisco ISE 1.2 patch introduced 4 Strip prefix or suffix @domaine Kingdom of the username through ISE with AD used as external identity Source. But the documentation is not updated for this feature. I am able to band 1 domain successfully suffix but following conditions listed in the list of suffixes fails to get stripped.

  Any thoughts on the same.

  Thanks Kumar

  In the ISE under Administration > identity management > external identity Sources

  Choose the Active Directory on the left, select your ad server and Advanced settings

  Under identity band of suffix, make sure prefixes band below: is selected (I know, it says prefix).

  In the list of Suffixes box, enter your list of domain suffixes to undress.  The separator character is a comma (,).

  

  If this does not solve your problem, then I fear that a call to TAC may be in order.

  UPDATE *.

  Spaces are significant characters.  The registration of domains, so as such:

  @domain.com, @domain.local, @testdomain.com

  END UPDATE *.

  Please rate useful messages and mark this question as answered if, in fact, does that answer your question.  Otherwise, feel free to post additional questions.

  Charles Moreton

  Post edited by: Charles Moreton

• How can I know the FULL domain name &amp; names for the installation of a digital certificate Public in ISE?

  We are implemented a project with Cisco ISE; but comments Portal appears to users as a "untrusted site". For problems, a public digital certificate must be installed in Cisco ISE, so he can send it to users who enter the comments Web portal.

  Now... to sell me the certificate, VERISIGN needs to know settings ISE of the certificate, such as name of area COMPLETE, names subnames, etc... How can these parameters of ISE?

  Thaks a lot!

  This isn't an easy question to answer, there are a ton of variables to include

  Local web site Central Web Auth or Auth

  LWA, the WLC is the "man in the Middle" to the request of the customer for PSN (server nodes), the WLC takes the request webauth and resembles webauth then the redirect URL that you put in the WLC

  If the redirect webauth URL is https://ise01.mycompany.com:8443/guestportal/login.action, the WLC is a redirect but the virtual IP address comes in 1.1.1.1, who was as trustworthy or redirection complains, then you may have to get the public certificate for the fqdn of 1.1.1.1, and the comment server. You can create a CSR using openssl or you can just enter in ISE and create a CSR, but you can only set CN = ise01.mycompany.com and nothing else, as long you have a single NHP is good, but if you have several Ssnp, you need to change your CSR so that you have to use openssl to create CSR using a file openssl.cnf and then with openssl, you do the following:

  openssl req - new - nodes-out openssl.cnf omf-01 - ise04.csr - config

  You must do it the way I said above regardless of CWA or LWA, if you have more than one PSN, you must point to a FULL VIP domain name and then configure your DNS to answer for these host names. With LWA, you get virtual IP WLC involved 1.1.1.1, so you don't have to worry about getting a certificate for this, it is a cleaner installation, but you must always do all the rest. It must ensure that users of your guests have the opportunity to join the portal comments and be able to solve the given DNS the dns server that they have been configured with.

  Content of the file openssl.cnf:

  [req]
  nom_distinctif = req_distinguished_name
  req_extensions = v3_req
  default_bits = 2048

  [req_distinguished_name]
  countryName = name of the country (2-letter codes)
  countryName_default = en
  localityName = name of the locality (for example, City)
  organizationalUnitName = organizational unit name (for example, section)
  commonName = Common Name (eg, YOUR name)
  commonName_max = 64
  emailAddress = Email address
  emailAddress_max = 40

  [v3_req]
  keyUsage = keyEncipherment, dataEncipherment
  extendedKeyUsage = AutClient, serverAuth
  subjectAltName = @alt_names

  [alt_names]
  DNS.1 = guest.mycompany.com
  DNS.2 = guest.mycompany.com
  DNS.3 = ise01.mycompany.com

• New profile NAM AnyConnect of ISE to the customer

  Hello

  I'm in the middle of implementing Cisco ISE in a network. After some users connected via Dot1x and had installed AnyConnect, which I configured for Client Provisioning, they came to me the question whether wireless networks could automatically be pushed with the AnyConnect profile. One thing is certain, I said, and I changed the profile of NAM.

  Then all is well with the new connection of users, but users who have already logged do not get the profile up to date. Is it possible to push an AnyConnect profile or new configuration of Cisco ISE?

  Greetings,

  Carlo

  That is a good question.

  I don't know if it's the most effective way or only; but couldn't force you users to go back in the commissioning Client by adding a policy Posture in order to evaluate the profile of NAM?

• Change the URL redirection in Cisco ISE 2.1.0 comments Portal CWA

  Hello

  I've set up a guest Portal CWA with WLC 5508 8.0.133.0 and ISE 2.1.0.

  I did all the rules both Authenticatin and authorization, and I also see customers hit the rules of law. The rule of being redirects the client to a captive portal in ISE like this: cisco-av-pair = redirect url =https://ip:port/Portal/Gateway? sessionId = SessionIdValue & Portal = d30c7eb0...

  I have 3 different customer portals for each SSID and everything works fine.

  The problem is that, when the wireless client receives the URL ISE redictect (URL to access the portal of ISE comments), this URL is based on ISE DNS name, not on its IP address. My ISE FULL domain name is iselab01.example.local and the certificate indicating that the portal comments field is example.local.

  Now I was asked to create a new portal of comments but this time I have the certificate belongs to the domain example.org and need to redirect to this new portal comments use this new domain.

  I tried to code, in the authorization profile CWA, redirection to equivalent URL through the CISCO av pair as follows:

  Cisco-av-pair = redirect url =https://iselab01.example.org:8443/Portal/Gateway? sessionId = SessionIdValu...

  but it does not work, since the sessionIdValue is not replaced with its actual value when sending to the wireless client.

  Is it possible to change the URL for redirection of ISE somewhere just for a portal of comments?

  Best regards

  Simply use the automatic CWA parameter in the authz profile, rather than enter the cisco-av-pair yourself, you will find that you can change the part of the FQDN of the url, if the session ID is kept intact.

• Check the ISE for the VPN Cisco posture

  Hello community,

  first of all thank you for taking the time to read my post. I have a deployment in which requires the characteristic posture of controls for machines of VPN Cisco ISE. I know that logically once a machine on the LAN, Cisco ISE can detect and apply controls posture on clients with the Anyconnect agent but what about VPN machines? The VPN will end via a VPN concentrator, which then connects to an ASA5555X that is deployed as an IPS only. Are there clues to this?

  Thank you!

  The Cisco ASA Version 9.2.1 supports the change in RADIUS authorization (CoA) (RFC 5176). This allows for the gesticulations of users against the ISE Cisco VPN without the need of an IPN. Once a VPN user connects, the ASA redirects web traffic to the LSE, where the user is configured with a Network Admission Control (NAC) or Web Agent. The agent performs specific controls on the user's computer to determine its conformity against one together configured posture rules, such as the rules of operating system (OS) patches, AntiVirus, registry, Application, or Service.

  The posture validation results are then sent to the ISE. If the machine is considered the complaint, then the ISE can send a RADIUS CoA to the ASA with the new set of authorization policies. After validation of the successful posture and CoA, the user is allowed to access internal resources.

  http://www.Cisco.com/c/en/us/support/docs/security/Adaptive-Security-Appliance-ASA-software/117693-configure-ASA-00.html

• The ISE Cisco switch configuration

  Hi experts,

  I got the following network:

  Devices-> switch access-->--> access switch central office switch-> ISE Server

  All switches are capable IOS for the 802. 1 X and configurations of AAA for ISE to manage network devices. However, I read in the guide on the configuration of the switches in preparation for the deployment of the ISE of CIsco, but I wonder what should I configure switches for access and basic switches or only configure the switches for access to EHT?

  Thanks for your time to read!

  If all clients are non-DHCP clients, then no configuration is based or distribution at all.

  But you may need to search different options of profiling, if the customers are not active DHCP. Access switch supports the function of detection IOS? Would be very useful to have such a that it would send important profiling information at ISE. You may need to use the right options for ISE of profiling to determine the details of the endpoint.

  Concerning

  Vivek

• Cisco MX700 not save the name of the system or ntp

  Hello

  We have a new system of telepresence MX700. When I put the name of the system under Setup > System Configuration > system unit and click on save button name will update what to expect on the touchpad. If I restart the system setting is lost without fail. Even with ip address of the ntp server.  Does anyone else have this problem?

  The problem is a problem because the name of the system is that the appliance uses when it registers with DHCP, which means in turn that the DNS name keeps changing to "localhost" instead of the name that I chose.

  The code is

  Current version

  TC7.3.0.8cb420c

   

  thank you

  Dallas

  When you sign up at one end of the telepresence to CUCM, endpoint configuration is CUCM.

  Administration of endpoints running on 10.5.1 UCM TC7.2

  See pg 21 for SSH and pg 25 for the name of the system.  Probably best to review the entire document to make sure that everything is set correctly, just in case.

  I don't see NTP in this guide, but found one guide older where he told to do the following:

   Setting a NTP Reference for the endpoints In UCM Administration > System > NTP Reference Configure a Phone NTP Reference for the endpoints. *The NTP Reference must be in Unicast Mode. *Assign to Date/Time Group, which in turn is assigned to Device Pool.

• How can I activate the "Host key" for my sftp to the ISE Server?

  Hello

  I can't copy my files to upgrade 1.2 ISE to my repositories the.

  Here is a cut and paste of my CLI on one of my knots ISE after attemtping to copy from my workstation (running a SFTP server) to one of my nodes of ISE.

  XXX-ise-01 / admin # s copyftp: / //ise-upgradebundle-1.1.x-a-disque 1.2.0.899.i386.tar.gz.:.

  User name: Admin

  Password:

  % ERROR: backup failed due to one of the following reasons

  1 host option key is not configured

  2. the host key is removed due to the new image

  3 host key is removed from any other depositary having same ip/hostname

  % Please reconfigure the host key option

  % Error: transfer not possible

  I don't have whatever it is configured with the option "host key.

  I googled and searched, but cannot find references limited to the "Host key" command within Cisco. I tried various forms of it on the ISE node with no luck.

  I tried an FTP transfer, but it does not work.

  Any ideas?

  You can try to add a repository to your local configuration as an sftp server that should start the process host key.

  Thank you

  Tarik Admani
  * Please note the useful messages *.

• Cisco ISE 1.2 &amp; Cisco WLC 5508 v7.6

  Hi all

  We intend to upgrade our WLC to 7.6 to fix a bug with FlexConnect customer ACL but I just saw on the ISE Cisco compatibility table which it recommended only up to the WLC 5508 v7.5...

  Cisco told me to avoid 7.5 as it is in a State of defferred if anyone know or are running in a laboratory or production, ISE1.2 with a WLC v7.6 n 5508?

  I wish I knew rather questions of people know before hand than to have to go through a software update, and then restore.

  Thank you all

  Mario Rosa

  Definitely stay away from 7.5. I've done several deployments with the WLCs 7.6 running. The two main issues that I touched were:

  CSCue68065 - in this bug FlexConnect ACL does not work unless you have a regular (non FlexConnect) ACL created with exactly the same name

  CSCuo39416 - CWA does not not on FlexConnect APs. It would apply to you if you have older models APs

  I hope this helps!

  Thank you for evaluating useful messages!

• When I transfer mail, if I click a recipient and hit return, the name of the recipient is replaced by another name in the address book.

  When I transfer the mail on ICC, if I click a recipient and hit back, the recipient's name is replaced by a different name in the address book.

  It's bug and the bug fixers are working on it as soon as possible.

  The error only occurs if you use the key "TAB" or "Enter".
  So if you physically use the mouse to select recipients, and then click on in the other field, etc. - do not use TAB or Enter, then the fault does not occur.
  As an alternative, I highly recommend that you use the following method in the selection of contacts in new e-mail messages or in the transmission of emails.

  In a new message of Scripture
  Use the "Contacts sidebar". See the image below.
  If you do not see, then activate.
  'View' > "Contacts Sidebar" or toggle the view using the f9 key
  Select the address book
  Select the contacts
  Click on the button 'TO Addto' or one of the other options.

• When I type a name in the search bar Google using the classic homepage, nothing happens, it is to say, type the word BASEBALL, and then press ENTER, and nothing happens

  When I type a name in the search bar Google using the classic Home Page, nothing happens. By example, if I type the name of the BASEBALL and then press ENTER, nothing happens. This just started today.

  Clear the cache and cookies from sites that cause problems.

  "Clear the Cache":

  • Tools > Options > advanced > network > storage (Cache) offline: 'clear now '.

  'Delete Cookies' sites causing problems:

  • Tools > Options > privacy > Cookies: "show the Cookies".

  Do a check with some malware malware, analysis of programs on the Windows computer.
  
  You need to scan with all programs, because each program detects a different malicious program.
  
  Make sure that you update each program to get the latest version of their databases before scanning.

  • http://www.malwarebytes.org/mbam.php - Malwarebytes' Anti-Malware
  • http://www.superantispyware.com/ - SuperAntispyware
  • http://www.microsoft.com/security/scanner/en-us/default.aspx - scan Microsoft Security
  • http://www.microsoft.com/windows/products/winfamily/defender/default.mspx - Windows Defender: Home Page
  • http://www.safer-networking.org/en/index.html - Spybot Search & Destroy

  Alternatively, you can write a check for an infection rootkit TDSSKiller.

  • http://support.Kaspersky.com/viruses/solutions?QID=208280684

  See also:

  • "Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked