Antenna WIFI mainboard header

Similar Questions

• HP6700 on (blue) antenna wifi but cannot connect to the network

  HP6700 was working, now no airprint.  In settings, it says unable to connect to the internet.   I reinstalled wifi using WPS and have a blue light on the antenna.  On Ipad, it says printer is in "idle" mode.  How can he wake up?

  Printer files network      It is a solution copied from a previous post of Provost.

  First do the following:

  1. Print a printer wireless network Test report
  2. Print a Page of Setup network printer

  Possible solutions:

  • Move the printer to be closer to the router if the wireless network Test report indicates the intensity of the signal is "Very low" or "Low".
  • Move the printer away from the router if currently less than 1 m (3 ft.).
  • Look at the last page of the Network Configuration Page. Near wireless networks appears along with the channels they use. Together, the channel of your router to channel 1, 6 or 11 according to the proximity of other channels are and how many networks use each channel. Having other channels of network near your (less than 5 channels) is not good. Using a channel that is heavily used by other networks is also not good. Do not use the setting "Auto" from the channel on the router.
  • Change the width of your router to 20 MHz channel (or 54 Mbit/s). Do not use 40 MHz (or 300Mbps) parameters or 20/40 MHz (Auto).
  • If the wireless network Test report indicates 'more than a wireless router was found which corresponds to your wireless network (SSID)... name ', try changing the name of your network in your router to something unique.

  Note: you will need to reconnect all the wireless devices that connect to your network using the new network name.

  • Make sure that the "Auto off" function of the printer is disabled. If this feature is enabled, the printer turns OFF after a period of inactivity.
  • If you use an Extender 'Wireless' to extend the wireless signal, try turning it off to see if the problem goes away.
  • If you still have questions, set a static IP address on the printer. This can be done using the Home Page (EWS of the printer) or from the Panel on many models of printer printers. Several models of printers have a feature 'suggests the IP address. Use this feature if you are not sure what setting to use IP address.

  Note: you may need to use the "" Update IP address"utility provided by the printer software to update the software with the new IP address.

  Please let me know if it helps.

  Tobindo

  A representative not hp

• iPhone if disconnette dalla rete wifi quando e in stand by e no arrivano notifiche di messaggi, whastapp e mail

  Salve a tutti,

  Ho da poco labor-intensive UN iPhone 5s nuovo da 16 GB e da pochi giorni ho noticed he following problema: dopo a periodo di some UNAMET da quando block the screen, it wifi if disconnette e quando paper the screen, the linea wifi TR riconnette dopo few e secondo the e che tutti gli imessage diretta conseguenza, I send whatsapp e messaggi , arrivano in e remember mi are not notify all' arrival. Questo fino a pochi giorni fa no accadeva. Ho ripristinato he telefono come nuovo e Ho aggiornato (iOS 9.2.1), ho router resettato it my questa cosa continued a sometimes. Sapreste tell is forward-looking questo da UN don't dell'antenna wifi del mio iPhone oppure da una functional di cui non ero a knowledge, che probabilmente dispersion o disattiva instradamento wifi per ridurre lo spreco della batteria? Grazie

  Anche io ho da tempo questo problema, ho resettato router Wi - Fi, iPhone e iPad my he problem persists any rete WiFi con. Just bloccato a TR disconnette volte, a volte anche mentre TR use there phone. Really un problema molto fastidioso, escluderei categoricamente che if tratti di una functional come invece leggo some support, prima dellaggiornamento an iOS 9.1 (circa) non avevo some tipo di problema.

  In fact many functional legate al wifi if svolgono proprio mentre he telefono e bloccato e conesso come backup, caricamento foto sulla libreria, aggiornamento applications, musical libreria aggiornamento... No would by tanto senso.

• iPhone 5 c Bluetooth wheel turns and the time is also incorrect.

  Hello, I have a 5 c iPhone, bluetooth does not work and the wheel rotates continuously in setting > Bluetooth.

  On the bottom bar when I press the Bluetooth Button, he said that, but when you go to set the Dungeon of the wheel spinning. The weather is bad, is so slow that after 1 hour, the clock rest 30 minutes behind. I tried just as hard reset, back up the bluetooth/wi-fi antenna, automatic or manual clock setting and the last thing I tried was replacing antenna wifi/bluetooth, it still didn't work do not. I have contacted Apple but they say that I need and an appointment with a technician, but I don't want to spend too much money on my phone because I think they are just too much money. Is there a solution to this problem, or is that the new antenna is faulty as well?

  PLEASE HELP ME!

  Hello

  You may have unintentionally caused more damage, "go back to the bluetooth/wi-fi antenna, automatic or manual clock setting and the last thing I tried was replacement antenna wifi/bluetooth, it still didn't work do not.

  But you could restore the iPhone settings > use iTunes on your Mac or PC to restore the iPhone, iPad or iPod to factory - Apple Support

• Wireless connection on Slimline s7520n

  As the subject says, I have a desktop Slimline s7520n pc.  I currently wired him with my router RJ45 cable.  I noticed that that's what I discovered as a reverse polarity SMA female end to an antenna wifi at the back of it.  The network adapter installed there b/g wireless capabilities?  Can someone tell me a good retailer to find such an antenna?

  My network card is a Realtek RTL8139/810 x Family Fast Ethernet NIC Device Manager also displays USB wireless 802.11 b/g adapter made by Gemtek (I guess it is internal).

  In addition, what is the wireless switch I need to turn on?  I looked everywhere in this pc and I can't find a switch.

  Thanks for your time.

  Message edited by Its_not_mine on 03/15/2009 15:06

  You will need no switch. It takes a male connector at the back of the computer. (threads)

  You need this size. http://tinyurl.com/c59nfa It is the same as the one I use on my S7700N. I had one which has an antenna with a long cable and it was horrible. The one I posted works better and takes place almost nil and gets in the way.

  Message edited by dmhoo29 on 03/15/2009 21:44

• Portege A200: Very low transfer wireless speed

  I have a router broadband wireless-B (brand linksys, model BEFW11S4 v4.0) and have problems connecting to it with the antenna WiFi integrated on my Portege A200. The connection is weak, with a very low speed (like a modem) transfer and also quite erratic, often dropping.

  It doesn't seem to be anything wrong with the antenna itself, as it has worked well elsewhere. The router also seems to be fine - in fact, I have a capable of achieving a good connection to it from my computer if I use a second antenna for a card PCMCIA Wireless-B.

  Can someone give me a clue as to what can happen? Y at - it a setting I should change, or is it possible that there is a mismatch between the laptop and the router?

  Thank you

  Hello

  Well, I guess for download and reinstall the latest WLan driver on the Toshiba site. This could help to solve this problem.

  Best regards

• HP ProBook G3 450: HP ProBook 450 G3 - upgrade form

  I just got a HP ProBook G3 450 Business Notebook 15.6 "Intel i5-6200U, 8 GB RAM, 1 TB HDD, AMD Radeon R7 M340 2 GB graphics card. We thought she had a 1920 x 1080 FHD display but in turn there only 1366 x 768 HD display.

  This can be improved?

  If so, what is the part number I need to order from HP to do and approximitley how much it would cost?

  Thank you

  Hello

  It has only the following options:

  35.6 cm (14 0-inch), LED backlight, eDP HD 16:9 aspect ratio - flat
  HD, glare, 1366 x 768, 220 nits, 3.6 mm, 1 or 2 antennas WLAN
  HD, glare, 1366 x 768, 220 nits, 3.6 mm, 1 or 2 antennas WIFI, camera
  HD, 1366 x 768, 3.6 mm, 1 or 2 antennas, WIFI, camera, touchscreen
  
  FHD eDP - slim
  FHD, glare, 1600 x 900, 220 nits, 3. 0 mm, 1 or 2 antennas WLAN
  FHD, glare, 1600 x 900, 220 nits, 3. 0 mm 1 or 2 antennas WIFI, camera

  It is a VERY expensive upgrade only from 1366 x 768 to 1600 x 900.

  Kind regards.

• Can I improve my wireless connection if I upgrade my hardware?

  I currently have this modem (provided by my internet provider)http://www.amazon.com/Motorola-SURFboard-SB5101U-DOCSIS-Cable/dp/B002M3SHXA/ref=sr_1_2?s=electronics...

  

  My router is:http://www.amazon.com/Cisco-Linksys-WRT160N-Wireless-N-Broadband-Router/dp/B000Z3U1P6

  

  My internet service is:

  Download 25 Mbps

  3 Mbit/s upload

  With my current hardware, I surge not what I could use?

  I can watch netflix by wifi on the PS3 or plug in my laptop via a HDMI to my Tv, but it puts in buffer much more when someone else in my apartment is as well the WiFi (phone, ipad... etc).

  I read on the new technology of AC that will hopefully me and another person to broadcast several HD movies and games at the same time.

  I can do better without upgrading my internet service?  How much better?  It is worth to buy new equipment for just a slight increase if that's what I get with new hardware?

  I hope that there is enough information here.

  Thank you

  Stephen

  Yes, it's true that streaming requires a lot of bandwidth. It is normal that your buffs of internet connection when many devices use the internet connection at the same time and especially when your wireless router is only a single band. And even when you're playing with the channels and use WPA2 Personal, the connection would still be affected if many devices using the same connection of single band on the router. I think that it is better for you to get a double router broadband. Dual band means that the router can simultaneously provide the connection 2.4 GHz and 5 GHz. For normal internet use, connect you devices to the 2.4 GHz network; and for streaming, you connect to the 5 GHz network. It is important to note that, in order for your wireless devices to connect to the 5 GHz network, that is on these devices wireless adapters should support or work with the network of 5 GHz (802 11A).  New models of Linksys router these days has access to the network of comments, too, which is an additional safety feature because the above devices will have a different IP address and will have no access to your main network.

  You check out the links below on what router that best suite your network must:

  Product comparison between routers Linksys Smart Wi - Fi

  http://KB.Linksys.com/Linksys/UKP.aspx?VW=1&docid=bb6925a91ad54105a51af9648ceefe78_Product_compariso...

  Product comparison between the Linksys EA6300, EA6400 and EA6700

  http://KB.Linksys.com/Linksys/UKP.aspx?VW=1&docid=ddcda37857b24a6eac2cd1e9ce266d65_Product_Compariso...

  http://www.alternativewireless.com/cellular-antennas/WiFi-solutions/5GHz-wireless-LAN.html

• Wi - Fi for 2 houses separated by 270 metres

  Hi all

  [Sorry for my English]

  We need to have Wifi access between 2 houses separated by 270 meters.

  We believe buying a 1240AG (AIR-LAP1242AG-E-K9) Aironet access point but we don't know which antenna to.

  I can install the antenna on the roof of my house and access point inside the House.

  In France, we are limited to 100MW (20dbm)

  Question 1:

  Is it possible that Wifi what to do?

  Question 2:

  Is the signal will be correct (minimum 11 ~ 15 Mbps) in the second house using a key usb wifi receiver or a receiver antenna wifi network card? This connection will be used only for Internet access.

  Question 3:

  What antenna you choose for my roof?

  Question 4:

  If I buy a dish, today, I will do to change for the next generation of Wifi 802.11n?

  You can see a picture of the 2 houses.

  Thank your for your help ;)

  I have to agree.

  You would basically be putting in place a bridge point to point between the houses, which are the most practical solution in your case.

  portable radio & antenna may or may not be able to see the signal given the fact that it will be a narrow beam (compared to the typical omnidirectional antenna), but it would take a long time to send the return signal - if she has even a 802. 11A radio! (assuming that you went with your radios on the APs

• My iPhone can connect to the computer via Wifi instead of cable? Because I figured that my head of the telephone cable i have problem if the computer cannot detect my folder after plugging in the cable.

  My iPhone can connect to the computer via Wifi instead of cable? Because I figured that my head of the telephone cable i have problem if the computer cannot detect my folder after plugging in the cable.

  Sync your iPhone, iPad or iPod touch with iTunes using a WiFi - Apple...

• It is possible, replace the antenna internal wifi iphone 5s?

  My iphone 32 5 s is perfect, like new, but since yesterday the anntenna internal wifi is broken. We can replace it in an apple store?

  I'm sure that the wifi antenna is broken is not a software problem.

• Mac Book Pro, outdoor WiFi antennas work to extend wi - fi range when plugged into USB PORTS

  Outdoor WIFI antennas work if plugged into the USB port on the Mac Book Pro. If they do, those who extend range of transmission and reception wi - fi?

  Sorry, but I've never used an external USB wifi antenna but if you describe your use case a wifi Repeater/Extender can be a good option for you. https://www.repeaterstore.com/pages/WiFi-booster-Repeater-Extender-differences

  If the option is not a Repeater/Extender so will have to wait for someone who has used an external USB antenna down to.

• Number of antennas router question?  (Several gadgets WiFi using 1 router)

  -My House is a 3 storey 5 bedrooms single family home.  There are 4 people living under his roof and each person has at least 3-4 items wireless who rely on our network domestic wi - fi.  Include wireless iPhone 2 of 6, 3 iPhone 5, 2 iMac (an older and a new one), 1 airbook, 1 MS Surface, 2 older laptops Apple (the old 1 "thick white), 2 iPads, Kindle 1-2, frame 1 photo wireless, 3 printers, wifi, 1 Sony PlayStation4 (via wifi) and much more.

  Our current router is a double (2.5 and 5) and we use them both, and we had recently a technician change the channels, so we are not in competition with the neighbors.  The router signal strength is strong in the home to most of the places.

  My question: with so many features, would be useful to have several routers with multiple antennas to accommodate this request, or made this same question?

  My current router has 3 visible external antennas.  I read that the Airport Extreme has 6 internal antennas.  I'm ready to go buy Airport Extreme, if 3 additional antennas can help, or if I can use two routers for a total of 9 antennas (if this is important).

  Our services to wide band is xfinity and we have one of their fastest options.  Not quite the 105, but about 80.

  Any suggestions?

  Several wireless routers will tend to work better than the Gothic pulpit super multi-antenna a monster looking for router.

  But they all need to be connected with the ethernet.

  Read how to get excellent wireless in your House.

  http://www.SmallNetBuilder.com/basics/wireless-basics/31576-the-best-way-to-get-ensemble-Maison-sans wire-coverage

  External antennas tend to be more effective than internal, but the actual number of antennas is easily overrated.

  Most of the antennas used on routers now are dual band... which means inside the plastic, they have sections for the two bands... If an antenna is really two.

  Our current router is a double (2.5 and 5) and we use both

  Is what model exactly? Of basic etiquette please.

  We had recently a technician change the channels, so we are not in competition with the neighbors.  The router signal strength is strong in the home to most of the places.

  It would have been correct for the first 5 minutes after the technician left the House and then totally out of place. Channel of all the equipment that surrounds you change every day, every hour... maybe every 5 min. While I don't disagree with fixing channel... others would say that it should be left on auto. You gain nothing much at all.

  If the signal strength is good over a 3-storey house, you are incredibly lucky.

  You can't effectively add routers more unless you install ethernet to provide an infrastructure for data streams.

• Satellite 1410-902: what is this device has a WiFi antenna?

  Hello.

  I have Toshiba S1410-902 and I want to make this computer works in wireless local area network. I am concidering buying card wifi Mini-PCI Slot, not the PCMCIA card. This is why I have a few questions:

  1. this model (s1410-902) there "build-in" antenna autour LCD? Purchase Mini-PCI wifi card can be unwise if the answer is 'no '.

  2. is there a list comatibilty miniPCI cards wifi? If yes - where? Blocks use of wifi cards of cards not compatible (such as CD-ROMs) BIOS?
  Buy the card wifi of any producer?

  Hello

  According to the specs of this device is ready WiFi and the antenna should be there. I put t know exactly where is the location of WiFi antenna, but it should be placed somewhere under the keyboard. It is very easy to remove the keyboard (fixed with three screws) and you can check if you can find the crack. There are also the antenna (black and white cables).

  Unfortunately I can't give you specific information about the compatible WiFi cards, but you can contact the Service partner in your country. I'm sure they can help you.

• P10 - 792 already built-in WiFi antenna?

  I have Toshiba satellite P10 792 and I try to install
  Intel 2100 WiFi but I can't find the built-in antenna

  http://nl.computers.Toshiba-Europe.com/contents/Toshiba_nl/NL/others/Pricelist/Prijslijst_Nederland_3jan2005.PDF
  as they say here on page 15.

  The pc is also a hardware switch radio power.

  Hello

  Gandalf is right. There is no card on your laptop wireless network. The best solution for you is on http://eu.computers.toshiba-europe.com section Products > Options & Accessories > Communications.

  I found one for you. It's Wireless LAN Mini PCI Card (802. 11 b / g) with part number PA3300U-1MPC.

  If there is no on/off switch you can enable/disable it in many ways. If you buy one and need help let us know.

  Good bye