EA4500 and PS3 abandons the connection

Similar Questions

• NETGEAR D6200 abandons the connection

  My netgear d6200 sometimes abandons the connection to my ISP, Ive tried to pass by the resolution of the problems several times and it goes through me by the same steps over and over until he finally asked my ISP details and then connects again and works fine.

  Additional information:

  1 details are all correct

  2 restart does not help

  3. it may take up to 2 hours just to do my job in connection

  Hi @Doswa

  Welcome to the community!

  You have the connection Mode is set to "Always On"? Otherwise, set it to this mode and observe your connection.

  What is the version of firmware installed on your gateway modem?

  In addition, make sure that you have the latest firmware installed on your device.

• Dell Server randomly abandons the connection to users.

  My Dell Server randomly abandons the connection to users in a building where the server does not find.  Different computers will sign the account and then randomly lose the connection to the server.  Thoughts?

  Post in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• Equium M70: card wireless regularly abandons the connection

  Hi, I wonder if anyone can help. My map regularly just Equiuim M70 wireless abandons its connection. If you browse on wireless networks, it seems my WEP encrypted network and it's one to connect to, as it says "Automatic" by him.
  If you click Connect it crashes with just "Waiting for network. So he can reconnect I have to go to network connections, right-click on the wireless connection, turn it off, then turn it back on and then it reconnects quite happy.
  I have the latest version of the installed Intel drivers and am allowing Windows XP manage connections.

  My Thinkpad R50 does not suffer the same problems. My wireless hub is a Dlink G604T.

  Has anyone else had similar problems - y at - it a cure? Is this a case of return my M70 and to repair/replace?

  Thank you

  Hello

  This problem also appears if WEP encryption is disabled?
  To me, it sounds like the card is not able to take the IP address automatically.
  This similar issue happens on my Toshiba laptop not. Sometimes, I have to use the repair of the WLan connection option to renew the ip address.
  It s not very serious problem for me and I can live with this question.

  I read in a net that can sometimes happen because of encryption theWEP and SP2.
  But if you want to get more details on the legs of connection on the M70, I suggest linking the Toshiba service partner in your country.

• App of Watch sounding abandons the connection to their iPhone app

  I used Smart sounding for about a year to control my hearing aid Linx2 with my iPhone and Apple Watch successfully. However, recently, the app shows interrupts the connection to the iPhone app. Hearing AIDS continue to work well with the iPhone, but they do not meet the application of the watch. Everyone knows about this problem? I reinstalled the apps and rebooted the on both devices. If! restart the watch, the app connects, but the connection is soon dropped. I don't know if the problem related to recent IOS upgrading or something else. Any thoughts on how to solve this problem will be appreciated. Thanks in advance!

  Have you tried devices pair the two UN - force to restart both of them and then re - pair again?

  Cancel the twinning of your iPhone - Apple and Apple Watch Support

  Restart your Apple Watch - Apple Support

  Apple Apple Watch support - Setup & matching-

• S50-B-12 q - WiFi adapter satellite abandons the connection

  The computer is a brand new Satellite S50-B-12 q.
  Everything seems to work outside the wireless card.

  When I first connect to my home network, it will have an internet connection for about 6 seconds, after which it changes status limited connectivity.

  The network uses WEP for security.
  Several other devices use without any problem.
  I tried everything I could think of:

  * Turning on computer power switch, reset of the card
  * Installation drivers new/rolling back drivers / different versions
  * Adapter enabled
  * Disabled the "allow the computer to turn off this device to save power".
  * Disconnection/reconnection to the network several times
  * netsh interface tcp set global autotuning = disabled / netsh interface tcp show global / netsh interface tcp set global autotuningl = normal
  Replacement of the windows 8, which comes with the computer with Windows 7 (same problem)
  * Troubleshooting with windows

  This is what it looks like when I ping:

  Ping google.com 173.194.32.39 with 32 bytes of data:
  Reply from 173.194.32.39: bytes = 32 time = 29ms TTL = 57
  Reply from 173.194.32.39: bytes = 32 time = 29ms TTL = 57
  Reply from 173.194.32.39: bytes = 32 time = 29ms TTL = 57
  Reply from 173.194.32.39: bytes = 32 time = 29ms TTL = 57
  Reply from 173.194.32.39: bytes = 32 time = 32ms TTL = 57
  Reply from 173.194.32.39: bytes = 32 time = 1075ms TTL = 57
  Request timed out.
  Request timed out.

  Basically, it works for like 6 seconds as mentioned previously, the ping increases a lot and then the connection is lost. Wired connection works perfectly.

  When I run diagnostics network integrated in windows 7, it shows the following:

  + * ProblΦmes trouvΘs: * +.
  The default gateway is not available/not fixed
  The connection between your access point, router, or modem cable, and the Internet is broken / detected

  I see that you have tried a lot of different solutions, but I put t see no workaround related to the WLan router.

  You said you are using WEP encryption.
  WEP is a very weak encryption standard. Usually its recommended to use WPA / WPA2 standard.
  I recommend you to reset the router back to factory settings WLan.
  Then test connectivity WLan using an open (unsecured) wireless LAN.
  But of course; This must be done only for testing purposes.

  You should also test different channels WLan (1-9). I guess that the Wlan router must contain settings too.

• Setting up Apple tv and stuck on the connection to the network screen

  Apple TV has tried to connect to my wifi.  He was slain on the connection to the screen of the network for 30 minutes.  No error message, just stuck.

  David, if, after checking your network on a different device - and assuming that

  your scope, that it still can't find your network quickly, I suggest you tv

  you restart.

  Tom

• Y560P card number: sleep mode and headset to the connected socket

  I searched the forum as much as I could and did not find this issue to be considered.

  So, sometimes I listen to music with headphones or even after a Skype call, I leave the connected headphones. If I put the laptop to sleep and wake it back up, unplug the headphones will not return my sound setting to speakers; I can't hear any sound if I plug the headphones in the back.

  I tried to connect and the new: no change. I tried to disable and re-enable "Realtek High Definition Audio" in the Device Manager: no change. Uninstall and reinstall it wouldn't be a good solution if it had to be done all the time. The only thing that it returns to normal is turning works again... typical I.T. solution. Is there a driver update to solve this problem?

  Speaking of driver updates, I guess that I can't find any BIOS update or updates to driver for the ideaPad due to the recall of Sandy Bridge?

  UPDATE: sorry... found the lenovo support site area sub consumer that is different from the IBM one... Argh...

  judge that?

• HP Pavilion DV6-7070SE: Broadcom 4313 802.11b/g/n abandon the connection lately

  Greetings,

  I'm planing to spend my wlan to 5 GHz because that starts them currently installed connection every few hours.

  Please advise on the correct module (P/N) for the 5 GHz model.

  If not supported, please refer to the best module that corresponds to my laptop.

  Thank you

  Hi @slimmy10 ,

  Thank you for visiting the Forums HP's Support and welcome. It's a great site for information and questions. I looked in your question about your HP Pavilion Notebook dv6-7070se and the connection Wireless drop. Before changing the wireless card, I would change the channel on the router. Routers are able to communicate to your laptop on several different channels, and sometimes it helps.

  You could disable IPv6 for the laptop. Some say this helps.

  Solve this problem Microsoft Fix it 50413.

  Here is a link to help as well.

  If you still feel the need to change the card to your laptop wireless. Here is a link to page 52 of your manual for cards supported wireless.

  Hope it will be useful.

  Thank you.

• AM300 abandon the connection

  IM connected to a Linksys AM300 Modem and within hours it will drop the connection and get ip address of 169.254.193.178

  -J' have flashed and reflashed the modem with the latest firmware, I have reset and reconfigured it 5 times more.

  -It is not connected to any router just directly to a computer and lan cable

  -J' set the modem to my ISP recommended settings and also tried experimenting with different settings

  -J' tried to put the static IP address and also try another computer MAC and PC same problem.

  Help please.

  Well, from what you described I suppose it must be defective and you may need to replace it as you already have to level/flashed the firmware, handed over to zero and re-set up a couple of times... Confirm the settings of your ISP again and see if there is any change, nothing else, you can try...

• Remote Desktop connection abandons the connection permanently

  When I connect to my office with Remote Desktop constantly gives up the connection in a few minutes. I have Windows Vista. I heard there were problems with Vista and this program. Someone has the answer on how to fix this? I can connect with my Wired PC without any problem. Thank you!

  Hi Drifter5,

  Welcome to Windows Vista answers Forums!

  You can try the following steps and check if you can solve the problem.

  Here are a few possible causes of connection problems:

  The port of remote desktop can be blocked by a firewall.

  If you are using Windows Firewall, follow these steps:

  1. open the Windows Firewall by clicking the Start button, click Control Panel, clicking Security, and then clicking Windows Firewall.

  2. click allow a program through Windows Firewall. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  3. Select the Remote Desktop check box.

  If you are using another firewall, make sure that the port (usually port 3389) remote desktop is open.

  Remote connections might not be enabled on the remote computer. To resolve this problem:

  4. on the remote computer, click the Start button, right-click computerand then click Properties.

  5. in the left pane, click remote settings. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  6. under Remote Desktop, click allow the connection of computers running any version of remote desktop or allow the connection of computers running with NLA authentication remote desktop.

  7. click on OK.

  For more information, please visit the following links:

  http://Windows.Microsoft.com/en-us/Windows-Vista/changing-remote-desktop-settings

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Remote-Desktop-problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/Remote-Desktop-connection-frequently-asked-questions

  If you use a wireless connection, then try to configure Windows to manage your network connections.

  For more information, you can consult the following link:

  http://TechNet.Microsoft.com/en-us/library/cc505913.aspx

  Hope this information is useful.

  Jeremy K

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• WRT54GL abandons the connection when you are using the 2.4 Ghz cordless phone.

  I recently upgraded to a Linksys WRT54GL router and also hooked into a phone jack of magic using a 2.4 Ghz cordless phone. The interent connection is perfectly fine until I try to use the wireless phone.

  Within 60 seconds, the completely wireless signal drops and interrupts the connection from the phone. About 30-60 seconds later the wireless signal comes back and sometimes the computer reconnects automatically.

  My router is in a totally different room on one ground other than cordless phone base, and I already changed the channel on my router for 11. My computer is the only thing in the House using the Wi - Fi connection at the moment. What causes this problem & how to fix it?

  p.s. The wired computer sees no interruption of internet connection while the phone is in use.

  
  

• WRT320N abandons the connection after minutes

  Just bought a WRT320N and implemented without problem. However, the internet connection keeps dying on me after only a few minutes. Reset in general (both modem and router) restores the internet for a few minutes, and then it dies again. The wireless signal is still visible on my computers, but I can't reconnect more until I have repeat the reset procedure.

  I looked for a firmware updated, but there is no update available (just the initial version). I will try this one facility tonight anyway, but I don't have high hopes, he will make a difference.

  The world is - that sound familiar at all? The recommendations, ideas, pointers?

  Thanks in advance!

  p.s. just curious, but all the world is also disappointed in the reception range? Despite the "Ultra Range Plus' promises, it does not give me a better range than my trusty old WRT54G... which is why I bought this new router.

  Thanks guys,.

  I have disable uPnP and some other settings changed (BG mixed mode, set to channel 11, set the interval of tag to 50, decreasing the fragmentation threshold). Don't know what did the trick, but it seems to work now. And it worked for a few hours in a row... YAY!

  Fingers crossed the internets are still there when I wake up tomorrow

• WRT110 abandons the connection

  Good day to all!

  My WRT110 interrupts the connection from time to time, once or twice randomly per night + when one of my other PC starts.

  I have a wired Synology DS209 NAS, Internet broadband (via modem) and several wireless computers. In this case, the problem is reproducible: I have a connection on 1 PC, and when I start one of the other PC, the connection drops for 5 minutes (both internet and to my NAS) on all connected systems. After these 5 minutes, each system will connect again. All systems have DHCP turned on and all systems have different IPs just before that happens. I did a "return to the default settings" and power cycles, but the problem remains.

  When I look at with Vistumbler (or NetStumbler), I see 90% to 0% signal drop once by - say - 5 minutes and irregular.

  Should I get a faulty router?

  Thanks for a reply...

  Drogreder

  On the computer windows 7 disable IPv6 under for two adapters Wi-wired and wireless LAN settings.  Restart and try again.

• Blur and expanded text and icons after the connection with Windows vista

  I have windows vista and when I turn on the laptop, the text and icons on the Welcome screen are normal, but after registration on the text and icons become slightly enlarged and fuzzy.  How can I get it back to normal?

  Hello

  There are a number of things to try:

  try going to your graphic card manufacturers site or computer and are looking for the driver download section

  Search your computer or graphics card model number based on what you have and download and install the latest graphics drivers for vista

  then try to make the screen of solution of problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-screen-resolution

  Change the screen resolution

  __________________________________________________________

  or try a restore of the system before this happened

  http://www.windowsvistauserguide.com/system_restore.htm

  If necessary do in safe mode

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.