Any directory on Cisco E20

Similar Questions

• Why did I suddenly lost the ability to view real images in any directory? I see now are drawn the same landscapes instead of each image. That's happened?

  Why did I suddenly lost the ability to view real images in any directory? I see now are drawn the same landscapes instead of each image. That's happened?

  Why did I suddenly lost the ability to view real images in any directory? I see now are drawn the same landscapes instead of each image. That's happened?

  Method #1

  Start button > in the search box, type options records > press the Enter key > click on view tab > under files and folders, uncheck "Always show icons, never thumbnails" > OK

  Method #2
   
  Start button > Control Panel > Classic view > systems > left column, system settings advanced > Performance tab, click on settings > tab Visual effects, click 'Show thumbnails instead of icons' > OK

  For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• Cisco e20... directory personal

  Hello

  for business reasons, I have to separate phone book...

  can I use a different LDAP catalogue on e20?

  Hello Ivan.

  I've not seen it described formally, but yes, you can use scp to transfer the file.

  The easiest for you would be to add a few entries, download the file, understand the syntax.

  Change it and download it again.

  The root account should be enabled on the endpoint. You can find the file under:

  /config/Pb.XML

  You may need to reboot endpoint after you have downloaded the file.

  Ivan: Please note my answers by using the stars under the messages!

• Authentication on Active Directory of Cisco IOS

  SCENARIO:

  2 cisco Secure ACS are configured to authenticate the connection of the user in Active Directory.

  RADIUS servers configured in IOS

  radius-server host 10.30.18.24

  radius-server host 10.30.18.25

  PROBLEM:

  When the primary server 10.30.18.24 Ganymede could not validate logon user, we have been disconnected from the router. Then I tried to change the order of the RADIUS servers in the router config that is

  radius-server host 10.30.18.25

  radius-server host 10.30.18.24

  and have gave us access. Can someone explain why 10.30.18.25 did not during the validation of the user in the first place?

  Concerning

  Simon

  Hi Simon,.

  Then the reason for this is, there are certain conditions that must be met before the unit tries to contact the second server in the config file.

  If you turn on,

  Debug aaa authentication

  you will get then 3 types of responses.

  -PASS

  -FAIL

  -ERROR

  Don't GO-> needs no explanation

  FAIL-> authentication server was available but the server has rejected the request of the user for some reason any.

  ERROR-> there is no response from the authentication server. No doubt its not accessible.

  ERROR is the only requirement when he will try to contact the following server defined in your configuration.

  So it's may be the likely reason why he never went pour.25.25 finished second et.24 was first, because que.24 was always accessible and returned FAIL for user authentication.

  Kind regards

  Prem

• Are Java and Flash (or any plugin; actually) supported by Linux Firefox 8? I don't see any directory in the installation directory plugins or lib.

  I don't see any plugin support on install Linux Firefox 8 tar.bz2 package. I tried libnpjp2.so and libflashplayer.so to the stable directory, but symbolic Firefox does not seem to recognize people. I can't find any mention of a disabling support for plugins (Java and Flash specifically) on Firefox 8 release notes. Someone else has this problem?

  You can create a folder plugins in the Firefox profile folder and put symbolic links in this folder.

  • http://KB.mozillazine.org/Profile_folder_-_Firefox
  • Help > troubleshooting information > profile directory: opens showing the file

• I can't find any directory called C:\WINDOWS\SYSTEM32\MACROMED. Can you advise me?

  I am running Vista 32 bit Service Pack 2 OS (windows Vista Home premium).  I recently downloaded "Adobe Flash Player 10 Active X".  It does not run is displayed for me select a desktop ICON.  I can find it in my control panel under "programs and features" where I can uninstall it if I want to.  I found a website that said it was a problem knowledge and my advice on how to solve the problem by following the methods described: 1. navigate to: C:\windows\system32\.   2. navigate to a directory called "ACROMED.  It is my problem, I do not have a listed directory called "ACROMED.  In any case after I do that I am to run flasutil9b and run as administrator, then follow the prompts through the installation of flash wizzard.  What I am doing wrong?  Unfortunately I am not computer enough to continue the process.

  Thank you to everyone out there that can help

  Flash Player is not a stand-alone program. It is a browser plugin; do not find a desktop icon or start menu for it.

  The instructions you found on the web are for Flash Player 9. Use these instructions to solve problems of Flash Player 10.

  http://kb2.Adobe.com/CPS/191/tn_19166.html

  Flash Player is installed in the C:\Windows\System32\Macromed\Flash directory

  The ActiveX is for Internet Explorer. If you use Firefox or Opera, you must download the NPAPI plugin as well.

• Custom wallpaper Cisco E20 USB

  Hi all

  I've recently updated one of our E20 products to the latest version of the TE4.1.1 software

  Now I want to change the wallpaper using the USB port, which deserves to be supported according to the Release Notes, but it does not work.

  When I insert the USB key with a few pictures on it (jpg, png and gif files) and I'm going to ' Menu > Wallpaper > get personalized USB wallpaper "it keeps saying"insert a USB key with image files to import a custom wallpaper.

  Are there specific dimensions, types for images?

  I tried .jpg, .png, .gif. JPG and 1280 x 720 images.

  Best regards

  Peter

  Hi Peter,.

  .PNG in 1280 x 720 should be good. One thing to check is that your USB drive is formatted as FAT, I don't know if the E20 will be able to mount filesystems more "sophisticated".

  -Andreas

• Data pump grant create any directory

  Hello
  
  I 've created the directory to use utility EXPDP as below.
  
  SQL > CREATE DIRECTORY test_expdp AS ' / export/oracle / ";
  
  1)
  SQL > GRANT READING, writing ON DIRECTORY test_expdp to THE System ;
  
  With grant command above to the directory of the user of the system, it is sufficient to take the backup of the entire database , just?.
  
  If I take backup sage schema , gets the backup generating right, since I gave the SYSTEM grants the user.
  
  2)
  SQL > GRANT READ, WRITE on DIRECTORY test_expdp TO public ; Give it will give to all users? Otherwise, how to give some grants to all current users of in database, which can take wise on sys backup system or scheme.
  
  3)
  Can I use utility impdp to import a file, the file that generated using utility exp.?

  Therese says:
  Hello

  I 've created the directory to use utility EXPDP as below.

  SQL > CREATE DIRECTORY test_expdp AS ' / export/oracle / ";

  1)
  SQL > GRANT READING, writing ON DIRECTORY test_expdp to THE System ;

  With grant command above to the directory of the user of the system, it is sufficient to take the backup of the entire database , just?.

  Yes

  If I take backup sage schema , gets the backup generating right, since I gave the SYSTEM grants the user.

  2)
  SQL > GRANT READ, WRITE on DIRECTORY test_expdp TO public ; Give it will give to all users? Otherwise, how to give some grants to all current users of in database, which can take wise on sys backup system or scheme.

  Give the grant to the public is to satisfy all users.

  3)
  Can I use utility impdp to import a file, the file that generated using utility exp.?

  No, this is not possible.

• Essmsh will not embark on any directory outside the bin (Windows 7)

  Just installed the client Essbase and EAS on my laptop Windows 7 x 64 (Version 11.1.1.3).
  
  I probably installed client tools on 10 different PC from XP to Vista to W7, and this is the first time I saw this question:
  
  The Essbase client installed correctly (for the most part), but I cannot launch essmsh from anywhere except c:\Hyperion\products\Essbase\EssbaseClient\bin.
  
  I tried several relocations, and something is always broken. I guess it's a problem with environmental variables, but I took a glance fast and things seem mostly fine.
  
  Was hoping someone could point me in the right direction for debugging this.
  
  Appreciated.

  WIn 7 is not compatible with 11.1.1.3.

  Reference - http://www.oracle.com/technetwork/middleware/bi-foundation/oracle-hyperion-epm-system-certific-2-128342.xls

  HTH-
  Jasmine.

• Switch Cisco 2960/3560 = > recovery password and default settings with the button Mode

  Hi Experts,

  I have some confusion with the button Mode with cisco 2960/3560 switches.

  I read on many forums and articles, but where things are not clear.

  a place given 3 seconds and somewhere is given 7 or 10 seconds.

  Qus1), what is the exact time to press/hold Mode button to perform two following tasks:

  A. password recovery (according to my knowledge 3 sec) good or bad?

  Configuration of the switch (start + run) would be safe

  After the recovery of password? Yes or no

  B. factory default (according to my knowledge 10 dry) good or bad?

  I'm afraid, because if I press mode button more than 3 seconds, then

  It will delete any configuration of cisco switch. Yes or no

  Qus2) I want to recover the catalyst 2960/3560 switch password without

  Start/run configuration to lose. That is my main concern.

  Please tell me how to do this, what will be the time keeping Mode buttom

  in a few seconds?

  Qus3) which means this line

  "If the password recovery mechanism is disabled in switch

  then you will lose all the config.

  This sentence has been given on this forum url

  https://supportforums.Cisco.com/thread/140848

  KS

  Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.

  Use the following terminal settings:

  • Bits per second (baud): 9600

  • Data bits: 8

  • Parity: None

  • Stop bits: 1

  • Flow control: Xon/Xoff

  Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.

  Unplug the power cable.

  The power switch and take it to the switch: command prompt:

  2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:

  Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.

  2960, 2970

  Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green.

  3560, 3750

  Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green.

  The system was interrupted before the flash at the end file system initialization

  loading the operating system software:

  flash_init

  load_helper

  boot

  switch:

  Run the flash_init command.

  switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.

  Run the load_helper command.

  switch: load_helper switch:

  Question the dir flash: command.

  Note: Be sure to type a colon ":" after the dir flash.

  Appears in the file system of the switch:

  switch: dir flash: Directory of flash:/ 2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4    -rwx  1131                     config.text !--- This is the configuration file. 5    -rwx  109                      info 6    -rwx  389                      env_vars 7    drwx  640                      html 18   -rwx  109                      info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.

  Type rename flash: flash: config.old config.text to rename the configuration file.

  switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.

  Issue the boot command to boot the system.

  switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.

  Enter "n" at the prompt to abort the initial configuration dialog box.

  --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.

  At the switch prompt, type en to enter a mode.

  Switch>en Switch#

  Password recovery

  Type rename flash: config.old flash: config.text to rename the configuration file with its original name.

  Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#

  Copy the configuration file in the memory.

  Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#

  The configuration file is now reloaded.

  Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.

  Note: Replace passwords that are required. You must crush not all passwords listed.

  Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password 

  Write the running configuration in the configuration file with the write memory command.

  Sw1#write memory Building configuration... [OK] Sw1#

  For factory reset:

  do not give under the control of factory reset

  Switch#copy flash:config.text system:running-config

  can I copy the running configuration to Flash

  Switch flash running-config #copy:

  Destination file name [running-config]?

  Building configuration...

  [OK]

  Switch #copy running-config startup-config

  Name of destination file [startup-config]?

  Building configuration...

  [OK]

  Review the link for more information below

  http://www.Cisco.com/en/us/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

  Please note the useful messages.

  Concerning
  Vesta
  "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

• Update Tandberg E20 TE2.1.0 TE4.1.0. Encrypt or not encrypt?

  Hello

  I am CCNP, but a beginner VOIP, just took a new job.  That is why the first VOIP LAN.

  I upgraded my LAN using switches of WS-C3560X.  I'm upgrading 60 Tandberg E20 video phones from TE2.1.0 to TE4.1.0 because of the E20 not finding the vlan voice.

  I use Avaya S8800 Server CM 5.2.1 with Avaya phones model 9640D01A-1009 and model Tandberg E20 video phones.

  I am trying to decide which software to use; with encryption or no encryption.

  Software Cisco E20

  S52100te4_1_1.pkg AES encryption

  No encryption s52101tenc4_1_1.pkg

  Q1.  What's being encryption?  Voice traffic is the obvious answer to this, no?

  Q2.  This device is at the other end of the encryption?  CM or telephone

  Q3.  Since the appeal will go outside my Avaya CM (ie. call to the outside world), encryption important?

  Thank you for your time and effort.

  Scott

  Hello.

  S52100te4_1_1.pkg AES encryption for the countries where the AES encryption are allowed.

  No s52101tenc4_1_1.pkg encryption is the countries where VOIP encryption is not allowed by law.

  You have only one key to unlock for one of them, so there is really no other choice.

  You can choose to disable encryption on the TE4 version (so it will have the same function as the TENC4), but you are not able to activate encryption on the TENC4.

  TE4 encryption is disabled by default, in any case, if the different software versions are here just for the legal question.

  Q1: Call for installation and the RTP stream can be configured to be encrypted on TE4.

  Q2: Endpoint or device interop

  Q3: It depends if your Avaya CM supports encryption or not.

  Thank you

  Marius

• Explorer.exe crashes when access to the context menu of any file character 1 long

  I use Windows XP SP3 and Explorer keeps if crush when I access the contextual (right click menu) not any folder that is one character long (a - z, 0-9).  For example, the folder labeled a will fail if it contains files or subfolders, if there in any directory, if it is on another drive, on the context menu.  In addition, in order to exclude any invalid context record, I have disabled all non-Microsoft tool ShellMenuView context menus.  I also tried to run Fixit 50043.  I also did a scan antivirus with norton antivirus.  Found nothing, no improvement.  It is 100% compatible.  BTW, I have already run System File Checker, and asides from this problem my system is perfect.  Everyone knows about this problem?  Any ideas on how to fix this problem without having to re - install XP?

  This applies only when the folder is labeled 1 character.  I don't know how the visual c ++ runtimes into play with explorer.exe in the context menu.  Re-don't install C++ runtimes for 2005, 2008, 2010 shows no improvement and install it with success.
  I get an error in visual c ++ runtime library.

  Nevermind, pretty sure winmount was the culprit.  Somehow, he escaped ShellMenuView, I disable the integration of shell of in the program and the turn is played.

• Windows Vista Home premium fresh install on a new SSD. Will not take any updates?

  Well, it will install that then it would download 122 updates after installing the windows updates just restart in a loop. If I go into safe mode it will complete step 3, and then restarts loop once again, if I restart and return in safe mode it will remove all updates but does not start in normal mode. Help, please.

  Hello

  I would suggest trying the following steps and check if it helps.

  (a) boot with the Vista DVD / disque disk recovery, select Repair Options , and then select command prompt (no admin password needed that way)

  (b) now type C: (or any directory of your system files are located)

  c) cd windows/winsxs

  d) del pending.xml

  (e) then close and restart the computer.

  I also suggest you to update all the drivers of the computer as well.

  Reference:--

  Error: failure of configuration of Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates: http://support.microsoft.com/kb/949358

  Note: It is strongly recommended that you back up all your personal files. For more information about how to back up your files, please visit: http://windows.microsoft.com/en-US/windows7/Back-up-your-files

  It will be useful.

• Cisco/Linksys lacks a PCI Express Wireless N card for desktop computers

  I bought a new gateway last year and noticed that there is no PCI slot for an internal wireless card.

  I've been running on an adapter of game without external G wire hooked to my ethernet port.

  I want to update my system for Wireless-N dual band, but to eliminate the clutter of my office.

  Anyone have any idea when CISCO/Linksys will have to use a card PCI E N dual-band available?

  (I'm willing to beta-test)

  Bill Calderwood

  Quality Director

  Kadient

  You could use a PCIe to PCI card and then use any PCI device you want (as long as he did)

  http://www.Amazon.com/STARTech-PCI-Express-adapter-card/DP/B0024CV3SA

• Cisco SKU or IDP description

  Hello team Cisco,

  Is there any tool from cisco for me to find a description SKU or PID?

  For example, I need to be able to MySapce for a PID like SL-29-UC-K9 and then a description such as CISCO (SL-29-UC-K9) UNIFIED COMMUNICATION LICENSE for CISCO 2901-2951.

  Have we not these tools?

  Thank you

  CCW would have that information.  Otherwise, Google is your friend.