Apply zeros

Similar Questions

• Advanced Tag Editor WMP 11 does not apply zero on track numbers 1-9

  Try to change the info tag track number for tracks 1-9 on my albums so the pieces will be in good condition on my phone, but a leading zero significant is not preserved when I clicked OK.  While my previous phone (LG VX8300) apparently looked at the names of files (which have the zeros) to maintain order, my current phone (LG env3) seems to use the info tag, so for every album all numbered titles 10 and above (but I guess that less than 20, if there were those who raised) appear between tracks 1 and 2.

  This is normal.
  You can leave your comments on the following link: http://mymfe.microsoft.com/Windows%207/Feedback.aspx?formID=195

  Edit: As a work around, you can use a numbering system used with for multi-disc albums, disc number and track number (mainly precede 1): 101, 102,..., 112, etc..

• Input calibration 9213

  I'm trying to calibrate a thermocouple on a 9213 module entry by injecting a CAG from a precision voltage source (see sketch). The problem I have is to determine what voltage to inject. I have the correct thermocouple table but I don't know if I need to take into account the temperature of the junction 'cold' to the terminals of the module (29 degrees) or the temperature of the junction created where my power supply connects to the compensation cable (20 degrees). Or maybe it's a combination of the two!

  If it makes any difference, the 9213 is configured for voltage measurement (not temperature) and the cold junction compensation is made by the reading of the temperature of cold welding of the module and adding the thermocouple emf equivalents.

  Can someone please advise.

  Thank you

  Thanks for the reply, but unfortunately, the document in the link does not solve my problem.

  My problem arises due to the thermocouple cable between terminals of the 9213 and taking of thermocouple in which I inject my compensation calibration voltages. However, I think I have a solution myself and I have included below in case anyone else has similar problems.

  If I have everything first apply zero microvolts in thermocouple decision-making and action on the 9213, measure is the emf generated in the cable compensation due to the difference between the cold welding of the 9213 and the temperature at the thermocouple socket. If I subtracted this emf since tensions injected during calibration, it eliminates the error and gives me a true result.

• Unable to save changes to the sounds. When registered and then double checked, change moved not. This applies specifically to sound for the navigation to start windows Explorer. I'm putting it to zero. »

  Unable to save changes to the sounds. When registered and then double checked, change moved not. This applies specifically to sound for the navigation to start windows Explorer. I'm putting it to zero.

  Unable to save changes to the sounds. When registered and then double checked, change moved not. This applies specifically to sound for the navigation to start windows Explorer. I'm putting it to zero.

  ====================================
  After making your change did you left click... Apply / OK?
  John Inzer - MS - MVP - digital media experience

• LR6 - when importing RAW, develop settings are applied it is-100 to highlight the exhibition shadows + 1.45 + 70.  How to import with zero development parameters.  I ran a few HDR mixes when I got the software and the DNG HDR file had these settings apply

  

  Probably, you set a default value for the camera. Go to preferences-> Presets and reset all camera default settings.

• Wireless zero configuration service has to be started manually

  Hello
  When I reboot my computer or turn it on after being turned off, my wireless
  zero configuration service has to be started manually by me every time. If I have
  do not start, my connection will not work. Even though I have set up the service
  to start automatically and then apply the change and then reboot, it still
  default values and no departures will support in the manual. Does anyone know how I could
  might cause, or could fix this problem?

  I appreciate your help.
  Salem

  Hello

  You use a Vista computer and is your ISP Internet BT by chance?

  If it is Vista, and especially if it is BT, download & install the following kb:

  http://support.Microsoft.com/kb/933872/en-us

  If you don't have XP, you can try the following:

  Launch-online Run => type cmd and click OK to open the command prompt

  type the following command (make sure you include spaces exactly as they are here):

  type sc config = own wuauserv

  Press ENTER. - you should see the text "change config service success."

  then type:

  SC config bits type = own

  Press ENTER. - you should be the text "change service config success."

  See you soon

• Assistant OR-9234/Sound and Vibration: being reset to zero (crazy) automatically input signals

  Hi all

  I have a voltage source and a force as entries in a sensor module DAQ 9234.

  The software focuses both signals whenever they change. For example, if the voltage is read by data acquisition increases up to a constant value, the software will trace an increase in tension, followed by a slow return to zero. Similarly, if I increase the force applied to the force sensor and keep it at a constant value, the program will draw an increase in force, followed by a return to zero.

  Here is a graphical representation of the problem, which uses the sensor force for example:

  

  The sensors are passive. The sensor is a PCB 02 208, and the source of tension comes from a LDM-1000 signal conditioner, which receives a signal from a MHR 250 LVDT. By the LVDT core displacement changes are interpreted by the signal conditioner, which translates as the measure of a voltage value that can be read by data acquisition.

  Thank you in advance.

  I assume you have the rule 9234 on coupling AC mode, while you should use DC coupling.

  -AK2DM

• Division by zero weird problem on HP 8200 Elite SFF

  Greetings,

  I posted my message here, it appears now that my problem is hardware specific.  My machine has the following specifications:
  
  HP Compaq 8200 Elite SFF
  Intel Core i5-2500 Duo @3.3 GHz processor
  8 GB memory

  Windows 7 x 64

  (I can provide more details if necessary)

  This has been me puzzled for more than a week now!

  We have an application where we lack in a division by zero. That request is deliberately built to raise exceptions in this case, with a call to the function _controlfp_s for edit masks on floating point exceptions.

  Now, when you run in a division by zero pretty much all of our machines, Visual Studio 2005 debugger breaks in the right place in our source files. However, on this machine, the location of the break is in every sense and seems to be unrelated to the real cause of the failure. So as a test, I built a simple win32 C program with just the following lines of code:

  int main (int argc, char * argv [])
  {
      float temp1, temp2, temp3;
      unsigned int control;
  
      _controlfp_s (& control, _EM_UNDERFLOW + _EM_INEXACT, _MCW_EM);
  
      Temp1 = 1.0;
      Temp2 = 0.0;
      Temp3 = temp1/temp2;
  
      return 0;
  }

  On all these 'good' machines, the code breaks when the temp3.  Among the other machines tested successfully, I had various hardware and operating systems, including Server 2008 R2, Windows XP x 32 and Windows 7 Pro x 64.  However, on this machine, the code stops at:

  C:\Program Files (x 86) \Microsoft Visual Studio 8\VC\crt\src\tidtable.c

  function:

  __set_flsgetvalue()

  In reviewing the records I have change the assembler code, everything seems fine until I hit the "ptsps" statement... then all records seem to be messed up (vs research as expected on a good machine). When comparing the stack on the good vs. bad, I also see entries of pile on the wrong machine, I don't see a good...

  Now... Here's what I did to solve problems:
  1. a disc image of the original disc HP on a hot spare and the original picture restored.
  2. only installed Visual Studio 2005 Pro - portion of C++.
  3 - tested above, code has always failed.

  4 - update all service packs Windows and tested above code.  Failed.

  5 - update all service packs, the Studio 2005 and tested above code. Failed.

  6 uninstalling all the bloatware and tested above code. Failed.

  7 - updating the BIOS and firmware and tested above code. Failed.

  8. install Visual Studio 2010 and tested above code. Failed.

  Then... I decided to take my spare disk image and install it on a similar, but a little older HP computer that we have, which has the following specifications:

  HP Compaq 8000 Elite SFF
  Intel Core Duo E8400 #3 GHz
  4 GB memory

  I went through the process of installation very well, even though she used the typewriter 8200 recovery partition.  On this machine, I simply installed the operating system and Visual Studio 2005 Pro - portion of C++.  No service packs not whatsoever (even if the Studio 2005 requires an update for 'vista') and the code worked as expected!

  So, that leaves me about almost everything but the material!  Also note that I tried to disable several processors and all optimization of the BIOS on the 8200, without success.
  
  I don't see anything else I can try... Please help!

  Wow!

  After the posting of this message to a friend... He found a document showing very similar symptoms on some of their CPUs from intel... I then found the exact document who applied to our specific processor (intel i5-2500) here:

  http://www.Intel.com/content/dam/www/public/us/en/documents/specification-updates/2nd-Gen-core-desktop-specification-update.PDF
  
  See Erratum BJ1

  This article describes pretty much exactly what I run into!  (Seriously), I never thought this would be a problem at THIS level!

• Cloning of the network settings on the printer - Smart zero 4.4 clients using Xen

  I ran into an issue trying to implement for thin client network printers Smart zero with the build Z6X44017 (same question for with prior build 4.3; same question for T520s, T610s, T620s): If the printer is set by the 'user' account in the HP printer Mapping utility, it does not pass by in a published desktop, XenApp as a printer available to all.  When changing the account 'user' to the 'administrator' account, the printer is listed in the printer mapping GUI.  But it is not available on the published desktop.

  However, if the printer is CREATED or MODIFIED by the administrator via the GUI HP printer Mapping on the Xen login Panel, then it is displayed as the default printer on the published desktop.

  As we seek to implement dozens of devices at once with the same network printer queue defined, it would be useful to set up once and then clone the settings.

  Here's what I've done so far:

  1 use the GUI HP printer Mapping utility to create (in administrator mode) network print queue and check that it works on the published desktop

  2. use HPDM to capture the root > printer-mapping-Bishop and root > registry values printers from that device using a task of 'files and records.

  3. apply these registry via the job template settings to the target group of devices.

  It works very well with regard to obtaining the printer to display in the GUI of the mapping of the printers on the Xen login Panel.  However, the same problem exists: unless I go again in administrator mode in the GUI and the Edit/save the printer, it is not available on the published desktop.

  A possible solution might be to run a job to 'validate' the printer settings via a program that could be run from the command line, but I can't find such a program in the file system for the Linux client.  It's just a bug in the configuration of the printer, or a limitation of this printer MUST be configured via the GUI only?

  

  The local HP sales engineer for thin clients was able to track down the command of "committing" the printer settings after running the registry task to copy the settings.  It is run as a task of type Script as a template file and registry.

  Here is the command to run in the script:

  /usr/share/Manticore/plugins/printer-mapping-Mgr/wrappers/apply.sh "root/printer-mapping-mgr.

  It can be added as the second subtask under the task of file & registry.

  The complete solution is:

  1 use the GUI HP printer Mapping utility to create (in administrator mode) network print queue and check that it works on the published desktop

  2. use HPDM to capture the root > printer-mapping-Bishop and root > registry values printers from that device by using a "file and registry" tasks and save it as a template

  3 edit the template to add a second sub-task of Script to run the command ' root/printer-mapping-mgr ' /usr/share/manticore/plugins/printer-mapping-mgr/wrappers/apply.sh

  4. run the task of file & registry model against the target devices.  This model will then apply these registry settings for the group target devices and run the script to validate the changes on the target devices.

• apply restrictions for the non-linear curve fit

  Hello Forum users,.

  I am currently working on a VI control which is supposed to create a specific model of pressure inside a hollow tube to provide a test environment for pressure sensors. The details are many and complicated, so let's say I am sure that my formula to calculate this profile according to the pressures inside the hollow rings around this tube will work.

  To find the correct pressure for each ring values, I've linked to a model VI containing this form to Lev. - Mar algorithm (the non-linear curve adjustment) and let it run.

  Technically, there is no problem and Lev - Mar find values to adjust the function for the values (not perfectly sure, but close enough).

  The problem is, however, that, since the device, once suitable values for the positioning and size of the rings are found, must be built, the simulated pressure rings perhaps intersect not between them. To apply this rule, I added a check to my VI of model and if the values passed to Lev - Mar breaking the rules, the VI model gives a matrix of zeros to follow him (I tried an empty array, but that only leads to error messages).

  This solution did not work. Lev - Mar seems to ignore these cases always looks for values that break my rules (and if I put these values through my model VI, I get a matrix of zeros, as expected, so the audit seems to work).

  Perhaps I misunderstood the algorithm of Lev - Mar and it does not actually check each possible defined coefficients of finds.

  Is it possible to adapt to any function of a set of values while keeping the predefined boundary conditions?

  Oh, before I forget:

  I use LabVIEW version 8.2 in the Institute, because the workshop systems is not installed 8.5 for some reason any.

  Thanks in advance

  Thaliur

  Hi Thaliur,

  Thanks for posting on our forums.

  I understand your request you expect the algorithm to ignore a case to all zeros in the table. However, it is not implemented like this.

  Good news is, its source code can be edited and you could save your own personalized version of the algorithm of screws it is to you that you just add a check for a matrix of zeros or simply pass another parameter which indicates only a case of "broken rules". Then you would not have to continue the calculation.

  If I misunderstood your question, please clarify this. You can also post a code for further explanation, if you wish.

  Good luck with the project!

  Peter

• Cannot apply the update of KB2895237

  Hello-

  Windows Server 2008 R2 SP1

  I met with the next issue https://support.microsoft.com/en-us/kb/2895237, but I can't apply this update. Installation process hangs just without any error.

  Process monitor shows me that this process creates / puts end threads all the time, but nothing else. Just create/close etc. I tried to run it from the administrator, but go the same behavior. I have a server that has a lot of IO. It hangs once a week...

  Image of process monitor

  Dump information:

  READ_ADDRESS: GetPointerFromAddress: unable to read from fffff80001afa100
  GetUlongFromAddress: cannot read fffff80001afa1c0
  0000000000000030 non paged pool
  
  CURRENT_IRQL: 2
  
  FAULTING_IP:
  Rdbss! RxTimerDispatch + 49
  fffff880'03bb05e9 45395830 cmp dword ptr [r8 + 30 h], r11d
  
  CUSTOMER_CRASH_COUNT: 1
  
  DEFAULT_BUCKET_ID: WIN7_DRIVER_FAULT_SERVER
  
  BUGCHECK_STR: 0XD1
  
  Nom_processus: System
  
  ANALYSIS_VERSION: 6.3.9600.17336 (debuggers (dbg). 150226-1500) amd64fre
  
  DPC_STACK_BASE: FFFFF88001E94FB0
  
  TRAP_FRAME: fffff88001e8d250-(.trap 0xfffff88001e8d250)
  NOTE: The frame trap does contain not all registers.
  Some registry values can be set to zero or incorrect.
  Rax = fffff88001e8d410 rbx = 0000000000000000 rcx = fffff88003bcba00
  RDX = 0000000000000000 rsi = 0000000000000000 rdi = 0000000000000000
  RIP = fffff88003bb05e9 rsp = fffff88001e8d3e0 rbp = 0000000000000000
  R8 = 0000000000000000 r10 = 0000000000000082 fffff88003bcb9b0 = r9
  R11 = 000000000009a34b r12 = 0000000000000000 r13 = 0000000000000000
  R14 = 0000000000000000 r15 = 0000000000000000
  iopl = 0 nv up ei pl nz na po cy
  Rdbss! RxTimerDispatch + 0 x 49:
  fffff880'03bb05e9 45395830 cmp dword ptr [r8 + 30 h], r11d, ds:00000000'00000030 =?
  Reset the default scope
  
  LAST_CONTROL_TRANSFER: from fffff800018bc1e9 to fffff800018bcc40
  
  STACK_TEXT:
  fffff880 '01e8d108 fffff800' 018bc1e9: 00000000' 0000000 a 00000000'00000030 00000000'00000002 00000000'00000000: nt! KeBugCheckEx
  fffff880 '01e8d110 fffff800' 018bae60: fffffa80 ' 19a86c58 fffffa80 '19a86b50 fffff880' 01e65180 fffff880 ' 01e8d4c0: nt! KiBugCheckDispatch + 0 x 69
  fffff880 '01e8d250 fffff880' 03bb05e9: fffff880 '01e8d4c0 fffff800' 01807b7f 00000000'00000001 00000000'00004200: nt! KiPageFault + 0 x 260
  "fffff880 '01e8d3e0 fffff800' 018c816c: 00000000 ' 00000000 fffffa80 ' 1ad03ef0 00000012'40 c 30000-00000000'00000005: rdbss! RxTimerDispatch + 0 x 49
  fffff880'01e8d430 fffff800'018 c 8006: fffff880 '03bcb960 00000000' 0e7add82 00000000'00000000 00000000'00000000: nt! KiProcessTimerDpcTable + 0x6c
  fffff880 '01e8d4a0 fffff800' 018c7eee: 00002277' c5813571 fffff880 '01e8db18 00000000' 0e7add82 fffff880' 01e685c8: nt! KiProcessExpiredTimerList + 0xc6
  fffff880 '01e8daf0 fffff800' 018c7cd7: 000008c 0' 6957dfc1 000008c 0' 0e7add82 000008c 0' 6957dfd8 00000000'00000082: nt! KiTimerExpiration + 0x1be
  fffff880 '01e8db90 fffff800' 018b494a: fffff880 '01e65180 fffff880' 01e706c0 00000000 00000001' fffff800' 00000000: nt! KiRetireDpcList + 0 x 277
  fffff880'01e8dc40 00000000' 00000000: fffff880'01e8e000 fffff880 '01e88000 fffff880' 01e8dc00 00000000' 00000000: nt! KiIdleLoop + 0x5a
  
  
  STACK_COMMAND: kb
  
  FOLLOWUP_IP:
  Rdbss! RxTimerDispatch + 49
  fffff880'03bb05e9 45395830 cmp dword ptr [r8 + 30 h], r11d
  
  SYMBOL_STACK_INDEX: 3
  
  SYMBOL_NAME: rdbss! RxTimerDispatch + 49
  
  FOLLOWUP_NAME: MachineOwner
  
  MODULE_NAME: rdbss
  
  Nom_image: rdbss.sys
  
  DEBUG_FLR_IMAGE_TIMESTAMP: 54ac90b6
  
  IMAGE_VERSION: 6.1.7601.18711
  
  FAILURE_BUCKET_ID: X64_0xD1_rdbss! RxTimerDispatch + 49
  
  BUCKET_ID: X64_0xD1_rdbss! RxTimerDispatch + 49
  
  ANALYSIS_SOURCE: KM
  
  FAILURE_ID_HASH_STRING: km:x64_0xd1_rdbss! rxtimerdispatch + 49
  
  FAILURE_ID_HASH: {c5674c2a-abf0-8335-bd73-f6921423a27d}
  
  Follow-up: MachineOwner

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• Frequency counter measurement crashes when you're away point zero (NI USB 6343, error-200284)

  Members of the Forum,

  I have problems with a measure of the frequency on a DAQ Mulitfunction of NI USB 6343 X series.  I use the meter 1 (door axis for frequency signal, PIN to DGND 82 77). The couple HBM T10F flange that I use (powered by a power supply of 24V) emits a signal of frequency between 5000 and 15000Hz with 10000Hz being the zero point. Couple flange has a capacity of 5kN.m (15000Hz = 5kN.m; 5000Hz = - 5kN.m).

  I have been using the VI attached for a few months now without any problems.  Now, the VI works fine as long as the couple remains inside a few hundred Hz of the zero point.  However, when the frequency increases further reading couple begins to freeze and finally I get either of these two errors:-200279 or-200284 related samples is not not available.  I noticed that the light on data acquisition close compromise during these periods of frost.

  Here is an example step by step my problem using cal shunt of the flange of the couple:

  1. I have run the VI and couple bed properly around 10000HZ (Active light, indicator light ON)

  2. I have apply the excitation of 5V to the shunt cal and frequency climbs to about 50% of the ability to couple brackets (as it should)

  3. as soon as I remove the excitement 5V playback freezes and the light on the acquisition of data.

  4 if I apply the 5V once again, until the timeput occurs, the led turns on and the acquisition of data reads the signal correctly.

  This type of problem would be more DAQ-related or is it the flange of the couple itself.

  Thanks in advance,

  Mike

  Solved.

  I did some troubleshooting this morning and it turns out that the vibrations of the system had not tightened a screw that was connector to the stator flange torque causing a bad electric signal of the torque flange itself.

  Everything works fine again.

  -MB

• the volume button on my computer does not work, when I turn the sound upward just bar falls to zero, no idea?

  can someone me, help the sound icon on the bottom of my scree of the computer doesn't work, when I puch the bar until you get sound on my computer, it just goes back to zero all the time...

  Hi JacquelineStueck,
   
   
  Parameter by default on your computer would be to reduce the volume when inbound communications are detected.
   
  a. change the setting in your control-> Sound-> Communications tab panel ' doing nothing '.
   
  b. click on apply. Click OK.
   
  If this does not help, perform the clean boot in order to identify the request at the origin of this problem:
   

  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

  See the following article in the Microsoft KB for more information on how to solve a problem by performing a clean boot in Windows Vista or Windows 7:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Additional reference on:

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

• set up wireless zero control

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  1. Ideas: iam not very experinced with a pc so I could really use some help I'm trying to set up a wireless connection but when I try to connect to a connection of filtration it does not connect, and when I try to repair the connection he says cannot repair because wireless is not zero control all this started about a week ago When I called my internet provider and during the sentence they hard shotting me connected something reset it was something like winstock 32/config or something and since then, even though I try to hang upwards from my dsn don't box still no connection

  Hello

  If your computer or your wireless network card came with its own wireless network software, follow these steps:

  1. click on start and run, type ncpa.cpl, and then click OK.

  2. click on network connections.

  3. in the network connections, select your wireless connection, and then click on change settings of this connection.

  4. on the wireless networks tab, click to select the use Windows to configure my wireless settings check box.

  To start the automatic Wireless Configuration service, follow these steps:

  1.
  Click Start, click Run, type %SystemRoot%\system32\services.msc/s and then click OK.
   
  2.
  Double-click Wireless Zero Configuration.
   
  3.
  In the startup type list, click Automatic, and then click on apply.
   
  4.
  In the service status area, click Start, and then click OK

  Another article to look for troubleshooting:
  313242 KB - how to fix wireless network connections in Windows XP
  http://support.Microsoft.com/kb/313242

• network configuration zero:

  My Network zero configuration does not stay on after starting.  I have to manually start from services.msc. Can I find and download this hidden file if it is corrupted?

  Hello

  Follow the steps mentioned below and check if the problem persists.

  Step 1:

  I wouldn't say you for the manual value. I'd rather set you it to automatic.

  To start the automatic Wireless Configuration service, follow these steps:

  a. Click Start, click Run, type %SystemRoot%\system32\services.msc/s and then click OK.
  b. double-click Wireless Zero Configuration.
  c. in the startup type list, click Automatic and then click on apply.
  d. in the Service status area, click Start and then click OK.

  Step 2:

  If this is little help, try this registry key:

  Registry warning
  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows
  http://support.Microsoft.com/kb/322756/

  a. Click Start, Open Run
  b. Type "regedit.exe" click OK
  c. on the registry editor, find this key and change
  the value in the window/right pane (2):

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\WZCSVC =

  [WE] Start REG_DWORD 0x00000002 (2)

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\wscsvc =
  [WE] Start REG_DWORD 0x00000002 (2)