ASA 5505 AnyConnect

Similar Questions

• ASA 5505 Anyconnect traversal nat error

  Good afternoon gents,

  I installed an ASA 5505 and can connect with anyconnect, but when I do, I can't access my LAN, then my LAN can access my laptop.  In the newspapers, I see the following error message:

  Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside;10.139.50.1/64506 dst inside 10.201.180.5/53 refused because of the failure of path opposite of that of NAT.

  I can't seem to figure this point and nothing I read to try worked. Here's the relevant config, any help would be GREATLY appreciated.

  interface Vlan1
  nameif inside
  security-level 100
  IP 10.201.180.10 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 67.200.133.107 255.255.255.248
  !

  access extensive list ip 10.139.50.0 inside_nat0_outbound allow 255.255.255.0 10.201.180.0 255.255.255.0
  access extensive list ip 10.201.180.0 inside_nat0_outbound allow 255.255.255.0 10.139.50.0 255.255.255.0

  mask 10.139.50.1 - 10.139.50.50 255.255.255.0 IP local pool SSLClientPool

  Global 1 interface (outside)
  NAT (inside) 0 inside_nat0_outbound list of outdoor access
  NAT (inside) 1 0.0.0.0 0.0.0.0

  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  AAA authentication enable LOCAL console
  the ssh LOCAL console AAA authentication

  Try the nat statement 0 without the keyword on the outside.

  NAT (inside) 0-list of access inside_nat0_outbound

  In addition,

  sh run sysopt and stick out.

  Manish

• ASA 5505 AnyConnect 8.2 connect other subnets from site to site

  Hello

  I'm somehwat new Cisco and routing. I have an installation of two ASA 5505 that are configured for the site to site vpn and AnyConnect. The AnyConnect subnet can connect to inside VLANs to the SiteA but I can't for the remote to Site B subnet when you use AnyConnect. Any ideas? I have to add the subnet of 10.0.7.0/24 to the site to site policy? Do I need to set up several NAT rules? Details below.

  Site A: ASA 5505 8.2

  Outside: 173.X.X.X/30

  Inside: 10.0.5.0/24

  AnyConnect: 10.0.7.0/24

  Site b: ASA 5505 8.2

  Outsdie: 173.X.X.X/30

  Inside: 10.0.6.0/24

  The AnyConnect subnet cannot access the network of 10.0.6.0/24.

  Any help would be greatly appreciated! Thank you!

  Hello Kevin,

  You must go back to identity (outdoors, outdoor) identity NAT (essentially for two subnets (Anyconnect and Remote_IPSec).

  And of course to include traffic in the ACL for IPSec crypto and (if used) split with the Anyconnect tunnel.

  Note all useful posts!

  Kind regards

  Jcarvaja

  Follow me on http://laguiadelnetworking.com

• ASA 5505 AnyConnect 8.2 - Can't access and inside services

  Hello

  I have configured AnyConnect to use a subnet of 10.0.7.0/24 for its DHCP pool. I can connect to the ASA very well, but I can't access internal services on my subnet 10.0.5.0/24 which is my INNER interface vlan subnet. I configure NAT for exemption rule:

  allowed to Access-list inside_nat0_outbound line 2 extended 10.0.5.0 ip 255.255.255.0 Any-Connect-Pool-10-0-7-0 object-group

  AnyConnect is set to ignore all the ACL rules through the sysopt permit vpn connection.

  I don't know if I'm supposed to create another path to the VPN subnet or what exactly. When I ping my VPN subnet to a client on the subnet of the INTERIOR, I see ICMP traffic flowing through the FW, but I didn't get any answer. I do not split-tunnleing and I can not connect to internet either after establishing a VPN connection.

  Thanks in advance for the help.

  Hello

  You must ensure that the following setting is enabled

  permit same-security-traffic intra-interface

  You should also make sure PAT configured for your Pool of VPN Dynamics

  If your current dynamic PAT for internal users would

  Global 1 interface (outside)

  NAT (inside) 1 10.0.5.0 255.255.255.0

  Then you must add

  NAT (outside) 1 10.0.7.0 255.255.255.0

  Hope this helps

  Remember to mark a reply as the answer if it answered your question.

  Feel free to ask more if necessary

  -Jouni

• ASA 5505 AnyConnect Client issues

  I have a client who is able to use ordinary VPN client, but one of the lawyers bought a new laptop with Windows 8 and must now AnyConnect. I opened the customer and you connect, but it says that it cannot open a session with the following messages:

  AnyConnect was not able to establish a connection with the specified secure gateway. Please try again.

  Then I click OK and I get:

  The secure gateway rejected the connection attempt. A new connection attempt the same or another secure gateway is required, which requires authorization.

  The following message was received from the secué Bridge: no address available for an SVC connection.

  I have the config following running:

  : Saved

  :

  ASA Version 8.2 (5)

  !

  ASA host name

  domain.local domain name

  activate 8Ry2Yjt7RRXU24 encrypted password

  vCGdNOPVyz.a0N encrypted passwd

  names of

  name 10.10.10.10 DG-Commcast Commcast Default Gateway description

  name 20.20.20.20 DG-FirstCom description first default gateway of Communications

  name 10.10.10.11 ASA-outside

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  switchport access vlan 12

  !

  interface Ethernet0/2

  Speed 100

  full duplex

  !

  interface Ethernet0/3

  switchport access vlan 22

  Speed 100

  full duplex

  !

  interface Ethernet0/4

  switchport access vlan 22

  !

  interface Ethernet0/5

  switchport access vlan 22

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  the IP 192.168.0.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  address IP ASA-outside 255.255.255.248

  !

  interface Vlan12

  nameif backup

  security-level 0

  IP 168.93.174.130 255.255.255.248

  !

  interface Vlan22

  nameif phones

  security-level 100

  address 192.168.3.1 IP 255.255.255.0

  !

  passive FTP mode

  clock timezone CST - 6

  clock to summer time recurring CDT

  DNS lookup field inside

  DNS domain-lookup outside

  backup DNS domain-lookup

  DNS domain-lookup phones

  DNS server-group DefaultDNS

  domain.local domain name

  object-group service RDP tcp - udp

  EQ port 3389 object

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  object-group service LogMeIn tcp

  Globe description

  port-object eq 2002

  DM_INLINE_TCP_1 tcp service object-group

  Group-object LogMeIn

  port-object eq www

  EQ object of the https port

  outside_access_in list extended access allowed object-group TCPUDP any host 50,76

  . 252.34 object group RDP

  outside_access_in list extended access permit tcp any interface phones object-gr

  OUP DM_INLINE_TCP_1

  outside_access_in list extended access permit icmp any one

  outside_access_in list extended access permit tcp any host ASA-outside eq ssh

  inside_access_in of access allowed any ip an extended list

  VPNClient_splitTunnelAcl list standard access allowed 192.168.0.0 255.255.255.0

  inside_nat0_outbound list of allowed ip extended access any 192.168.10.0 255.255.255

  .128

  permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 19

  2.168.10.0 255.255.255.128

  VPNClient_splitTunnelAcl_1 list standard access allowed 192.168.0.0 255.255.255.0

  backup_access_in list extended access permit icmp any one

  pager lines 24

  Enable logging

  list of logging message BackupLineAlert 622001

  debug logging in buffered memory

  exploitation forest asdm warnings

  exploitation forest mail BackupLineAlert

  address record [email protected] / * /

  exploitation forest-address recipient [email protected] / * / level of information

  exploitation forest-address recipient [email protected] / * / level of information

  Within 1500 MTU

  Outside 1500 MTU

  backup of MTU 1500

  MTU 1500 phones

  local pool VPNDHCP 192.168.10.50 - 192.168.10.80 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ICMP allow all outside

  ICMP allow any backup

  ICMP allow all phones

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  Global 1 interface (backup)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 0 192.168.10.0 255.255.255.128

  NAT (inside) 1 192.168.0.0 255.255.255.0

  NAT (inside) 0 0.0.0.0 0.0.0.0

  NAT (phones) 1 0.0.0.0 0.0.0.0

  public static 50.76.252.34 (Interior, exterior) 192.168.0.254 netmask 255.255.255.255

  inside_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Access-group backup_access_in in the backup of the interface

  Route outside 0.0.0.0 0.0.0.0 DG - Commcast 128 Track1

  Backup route 0.0.0.0 0.0.0.0 DG-FirstCom 255

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  AAA authentication LOCAL telnet console

  AAA authentication http LOCAL console

  Enable http server

  http 192.168.0.0 255.255.255.0 inside

  http 192.168.10.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  No vpn sysopt connection permit

  monitor SLA 123

  type echo protocol ipIcmpEcho 8.8.8.8 outside interface

  NUM-package of 3

  Timeout 10000

  frequency 15

  Annex ALS life monitor 123 to always start-time now

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-AES-128

  SHA - ESP - AES - 128 - MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256

  -MD5-ESP-3DES-MD5 ESP-3DES-SHA SHA-DES-ESP ESP - THE - MD5

  backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  backup of crypto backup_map interface card

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint _SmartCallHome_ServerCA

  Configure CRL

  Crypto ca certificate chain _SmartCallHome_ServerCA

  certificate ca 6ecc7aa5a7032ebcf4e952d491

  308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130

  010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a

  30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b

  13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504

  0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72

  20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269

  65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d

  65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31

  30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b

  a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10

  9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc

  7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b

  15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845

  1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd

  18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced

  4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f

  81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201

  082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868

  7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101

  ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff

  45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777

  2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a

  1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406

  03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973

  69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403

  1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d

  2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101

  4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e

  b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a

  99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018

  481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16

  b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0

  5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8

  6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28

  6c2527b9 deb78458 c61f381e a4c4cb66

  quit smoking

  crypto ISAKMP allow outside

  ISAKMP crypto enable backup

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  !

  track 1 rtr 123 accessibility

  VPN-addr-assign local reuse / time 5

  Telnet 192.168.0.0 255.255.255.0 inside

  Telnet 192.168.10.0 255.255.255.0 inside

  Telnet timeout 20

  SSH 192.168.0.0 255.255.255.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 0.0.0.0 0.0.0.0 backup

  SSH timeout 5

  Console timeout 0

  dhcpd outside auto_config

  !

  dhcpd address 192.168.0.150 - 192.168.0.180 inside

  dhcpd 192.168.0.254 dns 8.8.8.8 interface inside

  lease interface 604800 dhcpd inside

  dhcpd domain.local domain inside interface

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  a statistical threat detection tcp intercept rate-interval 30 rate burst-400 averag

  e-rate 200

  NTP server 208.66.175.36 prefer external source

  NTP server 173.14.55.9 source outdoors

  WebVPN

  allow outside

  enable backup

  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image

  SVC profiles AnyConnectProfile disk0: / anyconnectprofile.xml

  enable SVC

  attributes of Group Policy DfltGrpPolicy

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  internal VPNClient group strategy

  attributes of VPNClient-group policy

  value of DNS 192.168.0.254 Server 8.8.8.8

  Protocol-tunnel-VPN IPSec svc webvpn

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list VPNClient_splitTunnelAcl_1

  domain.local value by default-field

  WebVPN

  profiles of SVC value AnyConnectProfile

  username screams password encrypted BQd7EeZN.0hvT privilege 0

  attributes of cries of username

  type of service admin

  tony U/UxEH5l0w5Q encrypted privilege 15 password username

  nancy lAnhc/SvNNSSR password user name encrypted privilege 0

  tunnel-group VPNClient type remote access

  tunnel-group VPNClient-global attributes

  address VPNDHCP pool

  Group Policy - by default-VPNClient

  tunnel-group VPNClient ipsec-attributes

  pre-shared key *.

  !

  !

  Server SMTP 192.168.0.254

  context of prompt hostname

  anonymous reporting remote call

  Cryptochecksum:de5e8aec62853af27945c52bf36

  : end

  The version of the client AnyConnect should be identical to the version that is loaded on the ASA? I use the 3.0.5080 client and the parameters of the client AnyConnect on the SAA's anconnect-win - 2.5.201 - kr.pkg

  Thanks for the help!

  Tony

  The error message gives a clue:

  No address available for SVC connection
  

  The client cannot work without an assigned IP address. As you have assigned a pool to the tunnel group, I suppose that the customer is not to connect to the desired group, but for the default group. At least, I see nothing in the config that gives the customer the right group.

  Try the following:

  WebVPN

  tunnel-group-list activate

  tunnel-group VPNClient webvpn-attributes

  enable Group VPNClient-alias

  With it, you get a drop-down menu in the client to choose the right tunnel-group.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• Issue of Cisco ASA 5505 Anyconnect Client NAT'ing

  Hello

  We have a split_tunnel RA Vpn configuration in a branch that works very well in all areas except the destinged of traffic for a specific website using https.  This provider does not allow HTTPS connections to bring some outside IP addresses.

  Essentially, this should work like this:

  RAVPN_client (10.4.4.0/27)--> https request to the (208.x.x.x) vendor_ip---> ASA55XX--> NAT_to_outside_ip--> to the vendor_ip (208.x.x.x) https request

  I need to understand how you would approach from ONLY this https traffic specific to the RA VPN without having to change the installer otherwise.

  Internal hosts (aka behind the ASA physically) have not any question at this site, as would his nat ip address outside that we expect.

  Here is what we use for the NAT Exemption it list 10.2.2.x, 192.168.100.x, and 172.23.2.x are other remote sites we have. The 10.4.4.0/27 RA VPN users don't have no problems connecting to them, regardless of the Protocol:

  Note to inside_nat0_outbound access-list of things that should not be Nat would

  access extensive list ip 10.12.1.0 inside_nat0_outbound allow 255.255.255.0 10.2.2.0 255.255.255.0

  access extensive list ip 10.12.1.0 inside_nat0_outbound allow 255.255.255.0 192.168.100.0 255.255.255.0

  access extensive list ip 10.12.1.0 inside_nat0_outbound allow 255.255.255.0 172.23.2.0 255.255.255.0

  access extensive list ip 10.12.1.0 inside_nat0_outbound allow 255.255.255.0 10.4.4.0 255.255.255.224

  access extensive list ip 10.4.4.0 inside_nat0_outbound allow 255.255.255.224 192.168.100.0 255.255.255.0

  access extensive list ip 10.4.4.0 inside_nat0_outbound allow 255.255.255.224 10.2.2.0 255.255.255.0

  access extensive list ip 10.4.4.0 inside_nat0_outbound allow 255.255.255.224 172.23.2.0 255.255.255.192

  Here is the list of interesting traffic that we push to the customers through the tunnel of the VPN connection.

  VPN_splitunnel to access extended list ip 192.168.100.0 allow 255.255.255.0 any

  VPN_splitunnel of access list scope 10.2.2.0 ip allow 255.255.255.0 any

  Access extensive list ip 10.12.1.0 VPN_splitunnel allow 255.255.255.0 any

  Access extensive list ip 172.23.2.0 VPN_splitunnel allow 255.255.255.192 all

  Access extensive list ip 10.4.4.0 VPN_splitunnel allow 255.255.255.224 all

  VPN_splitunnel list extended access permit ip host 208.x.x.x any newspaper<- this="" is="" the="" vendors="" external="" ip="" address="" (obfuscated="" for="" security="" but="" you="" get="" the="">

  Here's the rest of the nat configuration:

  NAT-control

  Overall 101 (external) interface

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 101 0.0.0.0 0.0.0.0

  Configuring VPN RA:

  IP mask 255.255.255.224 local pool VPNPool 10.4.4.5 - 10.4.4.30

  WebVPN

  allow outside

  AnyConnect essentials

  SVC disk0:/anyconnect-dart-win-2.5.0217-k9.pkg 1 image

  SVC disk0:/anyconnect-macosx-i386-2.5.2001-k9.pkg.zip 2 image

  enable SVC

  tunnel-group-list activate

  internal RAVPN group policy

  RAVPN group policy attributes

  value no unauthorized access to banner

  value of banner that all connections and controls are saved

  banner of value this system is the property of MYCOMPANY

  banner value disconnect IMMEDIATELY if you are not an authorized user.

  value of server WINS 10.12.1.11 10.2.2.11

  value of 10.12.1.11 DNS server 10.2.2.11

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list VPN_splitunnel

  type tunnel-group RAVPN remote access

  attributes global-tunnel-group RAVPN

  address pool VPNPool

  authentication-server-group NHCGRPAD

  Group Policy - by default-RAVPN

  tunnel-group RAVPN webvpn-attributes

  enable RAVPN group-alias

  Can someone ' a Please direct me as to what I'm doing wrong? I was assuming that since I don't have Ip 208.x.x.x address in the list of inside_nat0_outbound that it would be NAT had, but appears not to be the case (out of packet - trace below)

  Packet-trace entry outside tcp 10.4.4.6 34567 208.x.x.x detailed https

  *****************************************************************************

  Phase: 1

  Type:-ROUTE SEARCH

  Subtype: entry

  Result: ALLOW

  Config:

  Additional information:

  in 0.0.0.0 0.0.0.0 outdoors

  Phase: 2

  Type: ACCESS-LIST

  Subtype: Journal

  Result: ALLOW

  Config:

  Access-group outside_access_in in interface outside

  outside_access_in list extended access permitted ip VPN_ips 255.255.255.224 host 208.x.x.x Journal

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd7bd3b20, priority = 12, area = allowed, deny = false

  Hits = 2, user_data is 0xd613bf80, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol

  SRC ip = VPN_ips, mask is 255.255.255.224, port = 0

  IP = 208.x.x.x DST, mask = 255.255.255.255, port = 0, dscp = 0 x 0

  Phase: 3

  Type: IP-OPTIONS

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd7df8fa0, priority = 0, sector = inspect-ip-options, deny = true

  hits = 2256686, user_data = 0 x 0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol

  SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =

  DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0

  Phase: 4

  Type: VPN

  Subtype: ipsec-tunnel-flow

  Result: ALLOW

  Config:

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd87c8fc8, priority = 12, area = ipsec-tunnel-flow, deny = true

  hits = 550, user_data = 0 x 0, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol

  SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =

  DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0

  Phase: 5

  Type: HOST-LIMIT

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd7dfbd28, priority = 0, domain = host-limit, deny = false

  hits = 1194, user_data = 0 x 0, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol

  SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =

  DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0

  Phase: 6

  Type: IP-OPTIONS

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Reverse flow from returns search rule:

  ID = 0xd7df8fa0, priority = 0, sector = inspect-ip-options, deny = true

  hits = 2256688, user_data = 0 x 0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol

  SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =

  DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0

  Phase: 7

  Type: CREATING STREAMS

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  New workflow created with the 2380213 id, package sent to the next module

  Information module for forward flow...

  snp_fp_tracer_drop

  snp_fp_inspect_ip_options

  snp_fp_tcp_normalizer

  snp_fp_translate

  snp_fp_adjacency

  snp_fp_fragment

  snp_ifc_stat

  Information for reverse flow...

  snp_fp_tracer_drop

  snp_fp_inspect_ip_options

  snp_fp_translate

  snp_fp_tcp_normalizer

  snp_fp_adjacency

  snp_fp_fragment

  snp_ifc_stat

  Result:

  input interface: outdoors

  entry status: to the top

  entry-line-status: to the top

  output interface: outside

  the status of the output: to the top

  output-line-status: to the top

  Action: allow

  *****************************************************************************

  Thank you

  Jason

  You are on the right track with you divided the tunnel configuration. You need to add is the pool of Client VPN to be coordinated to your external ip address, IE: same as your local users of the ASA when he tries to access the intellectual property of the provider (208.x.x.x), allowing more traffic in and out of the same interface for traffic of U-turn.

  Here's what you need to set up:

  permit same-security-traffic intra-interface

  nat-to-vendor ip 10.4.4.0 access list permit 255.255.255.224 host 208.x.x.x

  NAT (outside) 101-list of nat-to-vendor access

  The foregoing will allow VPN pool to be coordinated to your ASA outside the ip address of the interface when accessing the seller (208.x.x.x).

  1 small correction to your ACL split tunnel:

  -The following line is incorrect and should be deleted in the tunnel of split ACL:

  Access extensive list ip 10.4.4.0 VPN_splitunnel allow 255.255.255.224 all

  (As 10.4.4.0/27 is your pool of Client VPN, you do not add these subnet to your list of split tunnel. List of Split tunnel are only the network that you are difficult to access and sent through your VPN tunnel).

  Hope that helps.

• Unable to connect to ASA 5505 with AnyConnect after upgrade to 8.2

  I just bought a license of VPN AnyConnect Essentials for my ASA 5505.  I had to spend to 8.2 ASA.

  Now that I updated and installed the license, the AnyConnect client will connect is no longer.  It gives the following error: "failed to process the response.

  You can provide any help would be appreciated.  I am pleased to provide you with the configuration information that might be useful if you can provide the CLI commands, you want that I run.

  Looks like he doesn't like THEM too, you can change the encryption algorithm to 'not' include in your strategy:

  3des-sha1-aes128-sha1 sha1 aes256 encryption SSL

  In general is not very safe anyway, and the choice of encryption above will provide you with the best encryption strategy.

  Hope that helps.

• ASA - 5505 / good S2S / RemoteAccess with slow AnyConnect

  Hi all

  I use two ASA 5505 to sites. VPN between two works fine and fast that allows our ISP (~ 10MBit up/down).

  At home, I have normal ADSL (~ 600kbit up / down 6 Mbit)

  Downloading files from home on the internal server is fast, but when I connect through AnyConnect it is horrible slow.

  Both with the same zipfile on http server:

  The download speed with AnyConnect: 90 - 120 KB/s

  Download without AnyConnect speed: 660 KB/s

  Download the same file on the client to the other site of the Site 2 Site VPN server works quickly with 945 KB/s.

  I thought that maybe it's a ServicePolicyRule with QoS, but there are only the default rule where the QoS tab is not available and only ProtocolInspections are selectable.

  ASA 9.1.2

  ASDM 7.1.3

  AnyConnect Client 3.1.04063

  Any idea or suggestion?

  Well cordially

  Chris

  Hi Chris,

  Try lowering the value of mtu anyconnect 'anyconnect mtu 1300' in the group policy, and then test the question.

  You experience slowness for the internet traffic or for accessinng servers behind the ASA?

  Using fractionation on SAA tunnel?

  Kind regards

  NGO

• Key to mounting USB on an ASA 5505?

  Hello

  I have an ASA 5505 and the built-in flash is small enough and I put 3 .pkg on it for 4 Anyconnect.

  I formatted a memory stick (4 GB) to FAT32 and put in the USB Port 2 port on the back and restarted the firewall.

  But in file manager, I see disk0 and disk1, disk1 does not work, does not list anything but I can't create folders on this subject.

  Can I mount the USB key manually or something?

  Kind regards.

  The USB port on the 5505 is not a supported file storage location.

  In the most recent series 5500-X (including the X 5506), you can do this.

• ASA 5505 Security Plus license question

  Hi all!

  I have an ASA 5505 that I test with first entered with the Security Plus license. Recently, I erased flash and loaded the latest version of asa841 - k8.bin of IOS with asdm - 642.bin. Everything starts very well and came as he does so freshly however I noticed that I was now running only a basic license. If I run the sh key activation order, I noticed the following messages (exit complete is downstairs):

  The activation key running is not valid, using the default

  ......

  This platform includes a basic license.

  ......

  Unable to retrieve the activation key permanent flash

  I somehow kill my Security Plus licenses when I did the flash erase? If yes how do I to get it back?

  Thank you!!!

  -ken

  ciscoasa # sh - activation key

  Serial number: JMXXXXXXHU

  Activation key permanent running: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000

  The activation key running is not valid, using the default settings:

  The devices allowed for this platform:

  The maximum physical Interfaces: 8 perpetual

  VLAN: 3 restricted DMZ

  Double ISP: Disabled perpetual

  Junction VIRTUAL LAN ports: perpetual 0

  The hosts on the inside: 10 perpetual

  Failover: Disabled perpetual

  VPN - A: enabled perpetual

  VPN-3DES-AES: disabled perpetual

  AnyConnect Premium peers: 2 perpetual

  AnyConnect Essentials: Disabled perpetual

  Counterparts in other VPNS: 10 perpetual

  Total VPN counterparts: 25 perpetual

  Shared license: disabled perpetual

  AnyConnect for Mobile: disabled perpetual

  AnyConnect Cisco VPN phone: disabled perpetual

  Assessment of Advanced endpoint: disabled perpetual

  Proxy UC phone sessions: 2 perpetual

  Proxy total UC sessions: 2 perpetual

  Botnet traffic filter: disabled perpetual

  Intercompany Media Engine: Disabled perpetual

  This platform includes a basic license.

  Unable to retrieve the activation key permanent flash.

  The permanent activation key flash is the SAME as the key permanent running.

  Hi Ken,

  If you know what the license and activation for your security key, you can simply re - install it with the command "activation key" from the global configuration mode.

  If you have lost the key, you'll want to open a support case to get it retrieved.

  Hope that helps.

  -Mike

• ASA 5505 transparent mode dosnt pass traffic

  Hi all

  need help

  ASA 5505 do not pass traffic as a cordon of brewing, how do you get traffic?

  ciscoasa # sh ver

  Cisco Adaptive Security Appliance Version 8.2 software (5)

  Version 6.4 Device Manager (5)

  Updated Saturday, May 20, 11 16:00 by manufacturers

  System image file is "disk0: / asa825 - k8.bin.

  The configuration file to the startup was "startup-config '.

  ciscoasa until 55 minutes 31 seconds

  Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor

  Internal ATA Compact Flash, 128 MB

  BIOS Flash Firmware Hub @ 0xffe00000, 1024 KB

  Hardware encryption device: Cisco ASA-5505 Accelerator Board (revision 0 x 0)

  Start firmware: CN1000-MC-BOOT - 2.00

  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03

  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05

  0: Int: internal-Data0/0: the address is e4d3.f193.9486, irq 11

  1: Ext: Ethernet0/0: the address is e4d3.f193.947e, irq 255

  2: Ext: Ethernet0/1: the address is e4d3.f193.947f, irq 255

  3: Ext: Ethernet0/2: the address is e4d3.f193.9480, irq 255

  4: Ext: Ethernet0/3: the address is e4d3.f193.9481, irq 255

  5: Ext: Ethernet0/4: the address is e4d3.f193.9482, irq 255

  6: Ext: Ethernet0/5: the address is e4d3.f193.9483, irq 255

  7: Ext: Ethernet0/6: the address is e4d3.f193.9484, irq 255

  8: Ext: Ethernet0/7: the address is e4d3.f193.9485, irq 255

  9: Int: internal-Data0/1: the address is 0000.0003.0002, irq 255

  10: Int: not used: irq 255

  11: Int: not used: irq 255

  The devices allowed for this platform:

  The maximum physical Interfaces: 8

  VLAN: 3, restricted DMZ

  Internal guests: 10

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  SSL VPN peers: 2

  The VPN peers total: 10

  Double ISP: disabled

  Junction ports VLAN: 0

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect Cisco VPN phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes a basic license.

  Registry configuration is 0x1

  Modified configuration of enable_15 to 20:34:47.689 UTC Wednesday 5 December 2012

  ciscoasa #.

  ciscoasa #.

  ciscoasa # sh run

  : Saved

  :

  ASA Version 8.2 (5)

  !

  transparent firewall

  ciscoasa hostname

  activate 8eeGnt0NEFObbH6U encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  I haventerface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  Shutdown

  !

  interface Ethernet0/3

  Shutdown

  !

  interface Ethernet0/4

  Shutdown

  !

  interface Ethernet0/5

  Shutdown

  !

  interface Ethernet0/6

  Shutdown

  !

  interface Ethernet0/7

  Shutdown

  !

  interface Vlan1

  nameif inside

  security-level 100

  !

  interface Vlan2

  nameif outside

  security-level 0

  !

  passive FTP mode

  outs_in of access allowed any ip an extended list

  outs_in list extended access permit icmp any one

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  no ip address

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  outs_in access to the interface inside group

  Access-group outs_in in interface outside

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:234e9b9c6c9c941a89e37011325b6d5e

  : end

  ciscoasa #.

  ciscoasa #.

  ciscoasa #.

  ciscoasa # sh - access list

  access cached list the ACL log stream: total 0, 0 (deny-flow-max 4096) denied

  alert interval 300

  outs_in list of access; 2 elements; hash name: 0xd6c65ba5

  permit for access list 1 outs_in line ip scope any a (hitcnt = 0) 0x7d210842

  allowed to Access-list outs_in line 2 extended icmp any a (hitcnt = 0) 0x5532fcc5

  ciscoasa #.

  Hello

  Exactly... Good to know it works now.

  Do you know why he needs the IP address (such as a transparent firewall)?

  The ASA will act as a transparent layer 2 on the right device to the network, but what happens when the ASA does not have a particular destination mac address... What would be the source ip address of the package? Ip address of the ASA. So that's the main reason why we need that.

  We use it also for traffic management and for AAA services (if authentication is used the ASA will send the AAA authentication request to the server) with the IP address of this source.

  Please check the question as answered, so future users can pull of this

  Julio Carvajal

  Costa Rica

• How can I get the engine working in the ASA 5505 Crypto

  I bought a brand new ASA 5505 to connect to the Cisco 3640 and I can not yet set up the tunnel. I have tried to change the set of transformation to just but know luck. I recently put a VPN using DMVPN and Cisco 501 in a site-to-site, but it has been wondering what happens.

  The router (3640 executes code 12.4) seems ok and I don't think I have a problem with the router with Cisco 501 great work.

  This is a laboratory environment.

  This is the function defined on the ASA 5505

  The devices allowed for this platform:

  The maximum physical Interfaces: 8

  VLAN: 3, restricted DMZ

  Internal guests: 10

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Peer VPN: 10

  WebVPN peers: 2

  Double ISP: disabled

  Junction ports VLAN: 0

  AnyConnect for Mobile: disabled

  AnyConnect for Linksys phone: disabled

  Assessment of Advanced endpoint: disabled

  This platform includes a basic license.

  This is a ping from 10.3.4.10 to 10.1.1.1. He said nothing about IPSEC or ISAKMP.

  That's what I get when I do the: show crypto ipsec his

  ASA5505 (config) # show crypto ipsec his

  There is no ipsec security associations

  ASA5505 (config) # show crypto isakmp his

  There is no isakmp sas

  Debug crypto isakmp 10

  entry packets within the icmp 10.3.4.10 8 0 10.1.1.1 detail

  I have worked on it for a week and don't really know if I have a bad ASA5505. Since the normal stuff like browsing the Internet works and I can ping to the outside and inside, I don't know what to think. See attachments.

  "Do what you asked has worked.

  Nice to hear that your problem is solved.

  "My question is can I use the transform-set ESP-3DES-SHA instead of MD5?"

  Of course you can.

  Kind regards.

  Please do not forget to note the useful messages and check "Solved my problem", if the post has solved your problem.

• ASA 5505 Licensing / clarification of encryption

  Hello

  I have an ASA 5505 Security more than licenses.  The specific entry, that I focus on when I do a 'show' version is:

  AnyConnect Premium peer: 25 perpetual
  AnyConnect Essentials: 25 perpetual

  For my IPSEC IKEV2, I have:

  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha512
  Group 21
  FRP sha512
  seconds of life 10000

  Bringing a L2L VPN, I'm able to establish IPSEC/IKEV2 with DH group 21 without problem.
  But when I try to connect a remote client with Cisco Anyconnect, I get the following message:

  An IKEv2 remote access connection failed. Attempt to use an encryption without an AnyConnect Premium license of NSA Suite B (Group ECDH) algorithm.

  After research, I see that 19 Diffie-Hellman groups + are considered Next Gen NSA algorithms.  I guess that I don't have the correct license to support this with the AnyConnect client, so I edited my police ikev2 as follows:

  IKEv2 crypto policy 1
  14 21 group

  My problem is that I still get the same error.  Shouldn't the low AnyConnect - negotiate to group 14?  And shouldn't the L2L negotiate at the highest possible, group 21?

  All advice is appreciated.

  When you have licenses for AnyConnect Essentials and premium as ASA you must choose one or the other type for all customers AnyConnect.

  We see it in general where a customer started with the Essentials license, then later added Premium. When you do this, you must set up "no anyconnect essentials" in order to use features that require the level of Premium license.

  All Essentials customers should continue to work in your case, since the number of authorized users is equal on both types of licenses. On larger devices, licenses Premium can be less CALs Essentials since the former is sold by number of users (and can get very expensive on the larger machines because they are potentially 1000s of users) and the second is a relatively good cheap license which covers all of the device according to its material capacity.

  On the 5505 maximum capacity is 25 and you have same number already registered for the premium. (The premium SKU license available for this platform are 10 and 25).

• ASA 5505 VPN sessions maximum 25?

  Hello friend´s

  The company I work when acquired several ASA 5505, so now we will be able to connect several branches at Headquarters. But, now, I know that the ASA 5505 just scalates to 25 VPN sessions, I think that it won´t be enough to support the operations of an office. I have a lot of questions about this:

  Is - what the number 25 menas supporting up to 25 L2L tunnels? Or it means 25 sessions, regardless of the amount of L2L tunnels?

  Is this the way number 25 supporting up to 25 users in the Branch Office? Or it means that a user can use several sessions?

  I'm the stage of testing in a laboratory where one PC connects to many applications, at - it now someone if there is a command in the SAA to check how many VPN sessions is used?

  Please, do not hesitate to ask as much as necessary information. Any comments or document will be appreciated.

  Kind regards!

  Hi Alex,

  The assistance session 25 ASA 5505 VPN as max for IKEv1 or IPSEC tunnels customers it could be up to 25 L2L tunnels or 25 users using ikev1 (Legacy IPSEC client) and another 25 sessions for Anyconnect or Webvpn in this case are used in function.

  To check how many sessions VPN is currently running, run the command 'Show vpn-sessiondb' and 'display the summary vpn-sessiondb '.

  Find the official documentation for the ASA5505 on the following link:

  http://www.Cisco.com/c/en/us/products/collateral/security/ASA-5500-series-next-generation-firewalls/datasheet-C78-733510.html

  Rate if helps.

  -Randy-

• Site to site VPN upward but not pass traffic (ASA 5505 8.3.1 and 9.2.3 version)

  Hello

  I'll put up a tunnel vpn site-to-site between two locations.  Both have cisco ASA 5505 running a different version, I'll explain in more detail below.  so far, I was able to get the tunnel to come but I can't seem to pass traffic, I work at this for days now and have not been able to understand why he will not pass traffic.  Needless to say that the customer's PO would be on the fact that their VPN is not upward and they had to do by hand.  I'll put the configs below, if possible can someone help me as soon as POSSIBLE, I really want to get this site up and running so that we do not lose the customer.

  An IP address of 0.0.0.0 = site
  Site B IP = 1.1.1.1

  A Version of the site = 8.3.1
  Version of the site B = 9.2.3

  __________________________

  _________

  A RACE OF THE SITE CONFIGURATION

  Output of the command: "sh run".

  : Saved
  :
  ASA Version 8.3 (1)
  !
  hostname SDMCLNASA01
  SDMCLNASA01 domain name. LOCAL
  Select 5E8js/Fs7qxjxWdp of encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  the IP 192.168.0.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  the IP 0.0.0.0 255.255.255.252
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  passive FTP mode
  clock timezone CST - 6
  clock to summer time recurring CDT
  DNS lookup field inside
  DNS domain-lookup outside
  DNS server-group DefaultDNS
  SDMCLNASA01 domain name. LOCAL
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  network of the NETWORK_OBJ_192.168.0.0_24 object
  192.168.0.0 subnet 255.255.255.0
  network of the NETWORK_OBJ_192.168.1.0_24 object
  subnet 192.168.1.0 255.255.255.0
  network lan_internal object
  192.168.0.0 subnet 255.255.255.0
  purpose of the smtp network
  Home 192.168.0.245
  Network http object
  Home 192.168.0.245
  rdp network object
  Home 192.168.0.245
  network ssl object
  Home 192.168.0.245
  network camera_1 object
  host 192.168.0.13
  network camerahttp object
  host 192.168.0.13
  service object 8081
  source eq 8081 destination eq 8081 tcp service
  Dvr description
  network camera-http object
  host 192.168.0.13
  network dvr-http object
  host 192.168.0.13
  network dvr-mediaport object
  host 192.168.0.13
  object-group Protocol DM_INLINE_PROTOCOL_1
  object-protocol udp
  object-tcp protocol
  object-group Protocol TCPUDP
  object-protocol udp
  object-tcp protocol
  DM_INLINE_TCP_1 tcp service object-group
  EQ port 3389 object
  port-object eq www
  EQ object of the https port
  EQ smtp port object
  DM_INLINE_TCP_2 tcp service object-group
  port-object eq 34567
  port-object eq 34599
  EQ port 8081 object
  permit access ip 192.168.0.0 scope list outside_1_cryptomap 255.255.255.0 192.168.1.0 255.255.255.0
  outside_access_in list extended access permit tcp any any eq smtp
  outside_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group
  outside_access_in list extended access permit tcp any any DM_INLINE_TCP_2 object-group
  permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow all outside
  don't allow no asdm history
  ARP timeout 14400
  NAT (inside, outside) static static source NETWORK_OBJ_192.168.1.0_24 destination NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.1.0_24
  NAT (exterior, Interior) static static source NETWORK_OBJ_192.168.0.0_24 destination NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.0.0_24
  !

  
  network lan_internal object
  NAT dynamic interface (indoor, outdoor)
  purpose of the smtp network
  NAT (all, outside) interface static tcp smtp smtp service
  Network http object
  NAT (all, outside) interface static tcp www www service
  rdp network object
  NAT (all, outside) interface static service tcp 3389 3389
  network ssl object
  NAT (all, outside) interface static tcp https https service
  network dvr-http object
  NAT (all, outside) interface static 8081 8081 tcp service
  network dvr-mediaport object
  NAT (all, outside) interface static 34567 34567 tcp service
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 71.42.194.209 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  http server enable 8080
  http 192.168.0.0 255.255.255.0 inside
  http 192.168.1.0 255.255.255.0 inside
  http 192.168.1.0 255.255.255.0 outside
  http 71.40.221.136 255.255.255.252 inside
  http 71.40.221.136 255.255.255.252 outside
  http 192.168.0.0 255.255.255.0 outside
  http 97.79.197.42 255.255.255.255 inside
  http 97.79.197.42 255.255.255.255 outside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  card crypto outside_map 1 match address outside_1_cryptomap
  card crypto outside_map 1 set peer 1.1.1.1
  card crypto outside_map 1 set of transformation-ESP-3DES-SHA
  outside_map interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  dhcpd address 192.168.0.50 - 192.168.0.150 inside
  dhcpd dns 192.168.0.245 209.18.47.62 interface inside
  dhcpd SDMCLNASA01 field. LOCAL inside interface
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  attributes of Group Policy DfltGrpPolicy
  Protocol-tunnel-VPN IPSec l2tp ipsec
  tunnel-group 1.1.1.1 type ipsec-l2l
  tunnel-group 1.1.1.1 ipsec-attributes
  pre-shared key *.
  !
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  !
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:462428c25e9748896e98863f2d8aeee7
  : end

  ________________________________

  SITE B RUNNING CONFIG

  Output of the command: "sh run".

  : Saved
  :
  : Serial number: JMX1635Z1BV
  : Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor
  :
  ASA Version 9.2 (3)
  !
  ciscoasa hostname
  activate qddbwnZVxqYXToV9 encrypted password
  volatile xlate deny tcp any4 any4
  volatile xlate deny tcp any4 any6
  volatile xlate deny tcp any6 any4
  volatile xlate deny tcp any6 any6
  volatile xlate deny udp any4 any4 eq field
  volatile xlate deny udp any4 any6 eq field
  volatile xlate deny udp any6 any4 eq field
  volatile xlate deny udp any6 any6 eq field
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 1.1.1.1 255.255.255.252
  !
  passive FTP mode
  clock timezone CST - 6
  clock to summer time recurring CDT
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  network camera_http object
  host 192.168.1.13
  network camera_media object
  host 192.168.1.13
  network of the NETWORK_OBJ_192.168.0.0_24 object
  192.168.0.0 subnet 255.255.255.0
  network of the NETWORK_OBJ_192.168.1.0_24 object
  subnet 192.168.1.0 255.255.255.0
  outside_access_in list extended access permit tcp any any eq 9000
  outside_access_in list extended access permit tcp any any eq www
  outside_access_in list extended access permit icmp any one
  outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object NETWORK_OBJ_192.168.0.0_24
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow all outside
  ASDM image disk0: / asdm - 732.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) static static source NETWORK_OBJ_192.168.0.0_24 destination NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.0.0_24
  NAT (exterior, Interior) static static source NETWORK_OBJ_192.168.1.0_24 destination NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.1.0_24
  !
  network camera_http object
  NAT (all, outside) interface static tcp www www service
  network camera_media object
  NAT (all, outside) interface static 9000 9000 tcp service
  !
  NAT source auto after (indoor, outdoor) dynamic one interface
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 71.40.221.137 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  card crypto outside_map 1 match address outside_cryptomap
  card crypto outside_map 1 peer set 0.0.0.0
  card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
  outside_map interface card crypto outside
  trustpool crypto ca policy
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev1 allow outside
  IKEv1 crypto policy 120
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0

  dhcpd address 192.168.1.50 - 192.168.1.150 inside
  dhcpd dns 192.168.0.245 209.18.47.61 interface inside
  dhcpd SDPHARR field. LOCAL inside interface
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  AnyConnect essentials
  attributes of Group Policy DfltGrpPolicy
  Ikev1 VPN-tunnel-Protocol
  internal GroupPolicy_0.0.0.0 group strategy
  attributes of Group Policy GroupPolicy_0.0.0.0
  VPN-tunnel-Protocol ikev1, ikev2
  tunnel-group 0.0.0.0 type ipsec-l2l
  tunnel-group 0.0.0.0 ipsec-attributes
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.
  pre-shared-key authentication local IKEv2 *.
  !
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  !
  context of prompt hostname
  no remote anonymous reporting call
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:19031ab1e3bae21d7cc8319fb7ecf0eb
  : end

  Sorry my mistake.

  Delete this if it's still there

  card crypto external_map 1 the value reverse-road

  Add this to both sides

  card crypto outside_map 1 the value reverse-road

  Sorry about that.

  Mike