ASA 5505 AnyConnect 8.2 connect other subnets from site to site
Hello
I'm somehwat new Cisco and routing. I have an installation of two ASA 5505 that are configured for the site to site vpn and AnyConnect. The AnyConnect subnet can connect to inside VLANs to the SiteA but I can't for the remote to Site B subnet when you use AnyConnect. Any ideas? I have to add the subnet of 10.0.7.0/24 to the site to site policy? Do I need to set up several NAT rules? Details below.
Site A: ASA 5505 8.2
Outside: 173.X.X.X/30
Inside: 10.0.5.0/24
AnyConnect: 10.0.7.0/24
Site b: ASA 5505 8.2
Outsdie: 173.X.X.X/30
Inside: 10.0.6.0/24
The AnyConnect subnet cannot access the network of 10.0.6.0/24.
Any help would be greatly appreciated! Thank you!
Hello Kevin,
You must go back to identity (outdoors, outdoor) identity NAT (essentially for two subnets (Anyconnect and Remote_IPSec).
And of course to include traffic in the ACL for IPSec crypto and (if used) split with the Anyconnect tunnel.
Note all useful posts!
Kind regards
Jcarvaja
Follow me on http://laguiadelnetworking.com
Tags: Cisco Security
Similar Questions
-
VPN IPSec passthrough ASA 5505 (v9.2.4) - connected but no access
Hello
Here's my situation:
I am trying to connect a client IPSec VPN via an ASA 5505 to an other ASA 5505. In fact, I can make the connection to the VPN but all accesses are blocked (ping or IP access).
When I use a router ISP directly or at home, I have no problem (ping and IP access follow the firewall rules). Connection and access are allowed.
Schema:
I have attached both the configuration for this post
I've recently updated 8.2.5 ASA 8.4.6 and 9.2.4. An another ASA 5505 v8.2.5 works well in both way (via ASA VPN connection) and the VPN through ASA1 this ASA.
I have tried many solution to solve the problem (nat/ipsec static inspection), but I failed to solve it. I tried to see asp in ASA1 drop, but I was right to drop only "nat-xlate-failed".
Thanks for your help because I'm going crazy...
Olivier,
PS: Sorry for my English...
Hi Olivier,.
Could enable you icmp on the ASA inspection?
Use this command and check:
fixup protocol icmp
Kind regards
Aditya
Please evaluate the useful messages and mark the correct answers.
-
ASA 5505 Anyconnect traversal nat error
Good afternoon gents,
I installed an ASA 5505 and can connect with anyconnect, but when I do, I can't access my LAN, then my LAN can access my laptop. In the newspapers, I see the following error message:
Asymmetrical NAT rules matched for flows forward and backward; Connection for udp src outside;10.139.50.1/64506 dst inside 10.201.180.5/53 refused because of the failure of path opposite of that of NAT.
I can't seem to figure this point and nothing I read to try worked. Here's the relevant config, any help would be GREATLY appreciated.
interface Vlan1
nameif inside
security-level 100
IP 10.201.180.10 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 67.200.133.107 255.255.255.248
!access extensive list ip 10.139.50.0 inside_nat0_outbound allow 255.255.255.0 10.201.180.0 255.255.255.0
access extensive list ip 10.201.180.0 inside_nat0_outbound allow 255.255.255.0 10.139.50.0 255.255.255.0mask 10.139.50.1 - 10.139.50.50 255.255.255.0 IP local pool SSLClientPool
Global 1 interface (outside)
NAT (inside) 0 inside_nat0_outbound list of outdoor access
NAT (inside) 1 0.0.0.0 0.0.0.0Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authenticationTry the nat statement 0 without the keyword on the outside.
NAT (inside) 0-list of access inside_nat0_outbound
In addition,
sh run sysopt and stick out.
Manish
-
Hello world
I packed 2 VLAN (VLAN, VLAN B) on ASA 5505, in addition I VLAN 1. When I'm in the VLAN 1 I have access to all devices in VLAN A and B of VLAN (ping, ssh, etc.).
also I set up a VPN using Anyconnect as described below:
http://www.TechRepublic.com/blog/smbit/quick-guide-AnyConnect-client-VPN-on-Cisco-ASA-5505/387
everything works, I can connect, the tunnel is set up, but I have access to the devices in VLAN 1
could someone help me and tell me what I did wrong?
Thank you
Robert
Hello Robert,.
Given that your post is not clear on the question, when you wrote "everything works", I'll assume you have problems to access the VLAN A and B you customer annyconnect. It could be a problem with your NAT WITHOUT rules (sheep behavior depends on your Software ASA)
Please tell us which version of the software you're would be useful as well to help you correctly using and post with your config.
Jirka
-
ASA 5512 Anyconnect VPN cannot connect inside the network 9.1 x
Hello
I'm new to ASA, can I please help with this. I managed to connect to the vpn through the mobility cisco anyconnect client, but I am unable to connect to the Internet. the allocated ip address was 172.16.1.60 and it seems OK, I thought my acl and nat is configured to allow and translate the given vpn ip pool but I'm not able to ping anything on the inside.
If anyone can share some light... There's got to be something escapes me...
Here's my sh run
Thank you
Raul
-------------------------------------------------------------------------------
DLSYD - ASA # sh run
: Saved
:
ASA 9.1 Version 2
!
hostname DLSYD - ASA
domain delo.local
activate the encrypted password of UszxwHyGcg.e6o4z
names of
mask 172.16.1.60 - 172.16.1.70 255.255.255.0 IP local pool DLVPN_Pool
!
interface GigabitEthernet0/0
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/1
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/2
Post description
10 speed
full duplex
nameif Ext
security-level 0
IP 125.255.160.54 255.255.255.252
!
interface GigabitEthernet0/3
Description Int
10 speed
full duplex
nameif Int
security-level 100
IP 192.168.255.2 255.255.255.252
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
boot system Disk0: / asa912-smp - k8.bin
passive FTP mode
clock timezone IS 10
clock daylight saving time EDT recurring last Sun Oct 02:00 last Sun Mar 03:00
DNS lookup field inside
DNS domain-lookup Int
DNS server-group DefaultDNS
192.168.1.90 server name
192.168.1.202 server name
domain delo.local
permit same-security-traffic intra-interface
network dlau40 object
Home 192.168.1.209
network dlausyd02 object
host 192.168.1.202
network of the object 192.168.1.42
host 192.168.1.42
dlau-utm network object
host 192.168.1.50
network dlauxa6 object
Home 192.168.1.62
network of the 192.168.1.93 object
host 192.168.1.93
network dlau-ftp01 object
Home 192.168.1.112
dlau-dlau-ftp01 network object
network dlvpn_network object
subnet 172.16.1.0 255.255.255.0
the object-group Good-ICMP ICMP-type
echo ICMP-object
response to echo ICMP-object
ICMP-object has exceeded the time
Object-ICMP traceroute
ICMP-unreachable object
DLVPN_STAcl list standard access allowed 192.168.0.0 255.255.0.0
Standard access list DLVPN_STAcl allow 196.1.1.0 255.255.255.0
DLVPN_STAcl list standard access allowed 126.0.0.0 255.255.0.0
Ext_access_in access list extended icmp permitted any object-group Good-ICMP
Ext_access_in list extended access permitted tcp dlau-ftp01 eq ftp objects
Ext_access_in list extended access permit tcp any object dlausyd02 eq https
Ext_access_in list extended access permit tcp any object dlau-utm eq smtp
Ext_access_in list extended access permit tcp any object dlauxa6 eq 444
Ext_access_in access-list extended permitted ip object annete-home everything
pager lines 24
Enable logging
asdm of logging of information
MTU 1500 Ext
MTU 1500 Int
management of MTU 1500
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 713.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (Int, Ext) static source any any destination static dlvpn_network dlvpn_network non-proxy-arp
!
network dlausyd02 object
NAT (Int, Ext) interface static tcp https https service
dlau-utm network object
NAT (Int, Ext) interface static tcp smtp smtp service
network dlauxa6 object
NAT (Int, Ext) interface static tcp 444 444 service
network dlau-ftp01 object
NAT (Int, Ext) interface static tcp ftp ftp service
Access-group Ext_access_in in Ext interface
Route Ext 0.0.0.0 0.0.0.0 125.255.160.53 1
Route Int 192.168.0.0 255.255.0.0 192.168.255.1 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication enable LOCAL console
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
LOCAL AAA authentication serial console
the ssh LOCAL console AAA authentication
http server enable 44310
http server idle-timeout 30
http 192.168.0.0 255.255.0.0 Int
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec pmtu aging infinite - the security association
trustpool crypto ca policy
Telnet 192.168.1.0 255.255.255.0 management
Telnet timeout 30
SSH 192.168.0.0 255.255.0.0 Int
SSH timeout 30
SSH group dh-Group1-sha1 key exchange
Console timeout 0
No ipv6-vpn-addr-assign aaa
no local ipv6-vpn-addr-assign
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP server 61.8.0.89 prefer external source
SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
WebVPN
port 44320
allow outside
Select Ext
AnyConnect essentials
AnyConnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal GroupPolicy_DLVPN group strategy
attributes of Group Policy GroupPolicy_DLVPN
WINS server no
value of server DNS 192.168.1.90 192.168.1.202
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DLVPN_STAcl
delonghi.local value by default-field
WebVPN
AnyConnect Dungeon-Installer installed
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect ask flawless anyconnect
encrypted vendor_ipfx pb6/6ZHhaPgDKSHn password username
vendor_pacnet mIHuYi1jcf9OqVN9 encrypted password username
username admin password encrypted tFU2y7Uo15ahFyt4
type tunnel-group DLVPN remote access
attributes global-tunnel-group DLVPN
address pool DLVPN_Pool
Group Policy - by default-GroupPolicy_DLVPN
tunnel-group DLVPN webvpn-attributes
enable DLVPN group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the netbios
Review the ip options
inspect the ftp
inspect the tftp
!
global service-policy global_policy
SMTPS
Server 192.168.1.50
Group Policy - by default-DfltGrpPolicy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:67aa840d5cfff989bc045172b2d06212
: end
DLSYD - ASA #.Hello
Add just to be sure, the following configurations related to ICMP traffic
Policy-map global_policy
class inspection_default
inspect the icmp
inspect the icmp errorYour NAT0 configurations for traffic between LAN and VPN users seem to. Your Split Tunnel ACL seems fine too because it has included 192.168.0.0/16. I don't know what are the other.
I wonder if this is a test installation since you don't seem to have a dynamic PAT configured for your local network at all. Just a few static PAT and the NAT0 for VPN configurations. If it is a test configuration yet then confirmed that the device behind the ASA in the internal network has a default route pointing to the ASAs interface and if so is it properly configured?
Can you same ICMP the directly behind the ASA which is the gateway to LANs?
If you want to try ICMP interface internal to the VPN ASA then you can add this command and then try ICMP to the internal interface of the ASA
Int Management-access
As the post is a little confusing in the sense that the subject talk on the traffic doesn't work not internal to the network, while the message mentions the traffic to the Internet? I guess you meant only traffic to the local network because you use Split Tunnel VPN, which means that Internet traffic should use the VPN local Internet users while traffic to the networks specified in the ACL Tunnel Split list should be sent to the VPN.
-Jouni
-
Issue of Cisco ASA 5505 Anyconnect Client NAT'ing
Hello
We have a split_tunnel RA Vpn configuration in a branch that works very well in all areas except the destinged of traffic for a specific website using https. This provider does not allow HTTPS connections to bring some outside IP addresses.
Essentially, this should work like this:
RAVPN_client (10.4.4.0/27)--> https request to the (208.x.x.x) vendor_ip---> ASA55XX--> NAT_to_outside_ip--> to the vendor_ip (208.x.x.x) https request
I need to understand how you would approach from ONLY this https traffic specific to the RA VPN without having to change the installer otherwise.
Internal hosts (aka behind the ASA physically) have not any question at this site, as would his nat ip address outside that we expect.
Here is what we use for the NAT Exemption it list 10.2.2.x, 192.168.100.x, and 172.23.2.x are other remote sites we have. The 10.4.4.0/27 RA VPN users don't have no problems connecting to them, regardless of the Protocol:
Note to inside_nat0_outbound access-list of things that should not be Nat would
access extensive list ip 10.12.1.0 inside_nat0_outbound allow 255.255.255.0 10.2.2.0 255.255.255.0
access extensive list ip 10.12.1.0 inside_nat0_outbound allow 255.255.255.0 192.168.100.0 255.255.255.0
access extensive list ip 10.12.1.0 inside_nat0_outbound allow 255.255.255.0 172.23.2.0 255.255.255.0
access extensive list ip 10.12.1.0 inside_nat0_outbound allow 255.255.255.0 10.4.4.0 255.255.255.224
access extensive list ip 10.4.4.0 inside_nat0_outbound allow 255.255.255.224 192.168.100.0 255.255.255.0
access extensive list ip 10.4.4.0 inside_nat0_outbound allow 255.255.255.224 10.2.2.0 255.255.255.0
access extensive list ip 10.4.4.0 inside_nat0_outbound allow 255.255.255.224 172.23.2.0 255.255.255.192
Here is the list of interesting traffic that we push to the customers through the tunnel of the VPN connection.
VPN_splitunnel to access extended list ip 192.168.100.0 allow 255.255.255.0 any
VPN_splitunnel of access list scope 10.2.2.0 ip allow 255.255.255.0 any
Access extensive list ip 10.12.1.0 VPN_splitunnel allow 255.255.255.0 any
Access extensive list ip 172.23.2.0 VPN_splitunnel allow 255.255.255.192 all
Access extensive list ip 10.4.4.0 VPN_splitunnel allow 255.255.255.224 all
VPN_splitunnel list extended access permit ip host 208.x.x.x any newspaper<- this="" is="" the="" vendors="" external="" ip="" address="" (obfuscated="" for="" security="" but="" you="" get="" the="">
Here's the rest of the nat configuration:
NAT-control
Overall 101 (external) interface
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 101 0.0.0.0 0.0.0.0
Configuring VPN RA:
IP mask 255.255.255.224 local pool VPNPool 10.4.4.5 - 10.4.4.30
WebVPN
allow outside
AnyConnect essentials
SVC disk0:/anyconnect-dart-win-2.5.0217-k9.pkg 1 image
SVC disk0:/anyconnect-macosx-i386-2.5.2001-k9.pkg.zip 2 image
enable SVC
tunnel-group-list activate
internal RAVPN group policy
RAVPN group policy attributes
value no unauthorized access to banner
value of banner that all connections and controls are saved
banner of value this system is the property of MYCOMPANY
banner value disconnect IMMEDIATELY if you are not an authorized user.
value of server WINS 10.12.1.11 10.2.2.11
value of 10.12.1.11 DNS server 10.2.2.11
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_splitunnel
type tunnel-group RAVPN remote access
attributes global-tunnel-group RAVPN
address pool VPNPool
authentication-server-group NHCGRPAD
Group Policy - by default-RAVPN
tunnel-group RAVPN webvpn-attributes
enable RAVPN group-alias
Can someone ' a Please direct me as to what I'm doing wrong? I was assuming that since I don't have Ip 208.x.x.x address in the list of inside_nat0_outbound that it would be NAT had, but appears not to be the case (out of packet - trace below)
Packet-trace entry outside tcp 10.4.4.6 34567 208.x.x.x detailed https
*****************************************************************************
Phase: 1
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
in 0.0.0.0 0.0.0.0 outdoors
Phase: 2
Type: ACCESS-LIST
Subtype: Journal
Result: ALLOW
Config:
Access-group outside_access_in in interface outside
outside_access_in list extended access permitted ip VPN_ips 255.255.255.224 host 208.x.x.x Journal
Additional information:
Direct flow from returns search rule:
ID = 0xd7bd3b20, priority = 12, area = allowed, deny = false
Hits = 2, user_data is 0xd613bf80, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol
SRC ip = VPN_ips, mask is 255.255.255.224, port = 0
IP = 208.x.x.x DST, mask = 255.255.255.255, port = 0, dscp = 0 x 0
Phase: 3
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:
Direct flow from returns search rule:
ID = 0xd7df8fa0, priority = 0, sector = inspect-ip-options, deny = true
hits = 2256686, user_data = 0 x 0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol
SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 4
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional information:
Direct flow from returns search rule:
ID = 0xd87c8fc8, priority = 12, area = ipsec-tunnel-flow, deny = true
hits = 550, user_data = 0 x 0, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol
SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 5
Type: HOST-LIMIT
Subtype:
Result: ALLOW
Config:
Additional information:
Direct flow from returns search rule:
ID = 0xd7dfbd28, priority = 0, domain = host-limit, deny = false
hits = 1194, user_data = 0 x 0, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol
SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 6
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:
Reverse flow from returns search rule:
ID = 0xd7df8fa0, priority = 0, sector = inspect-ip-options, deny = true
hits = 2256688, user_data = 0 x 0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol
SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 7
Type: CREATING STREAMS
Subtype:
Result: ALLOW
Config:
Additional information:
New workflow created with the 2380213 id, package sent to the next module
Information module for forward flow...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_tcp_normalizer
snp_fp_translate
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat
Information for reverse flow...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_translate
snp_fp_tcp_normalizer
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat
Result:
input interface: outdoors
entry status: to the top
entry-line-status: to the top
output interface: outside
the status of the output: to the top
output-line-status: to the top
Action: allow
*****************************************************************************
Thank you
Jason
You are on the right track with you divided the tunnel configuration. You need to add is the pool of Client VPN to be coordinated to your external ip address, IE: same as your local users of the ASA when he tries to access the intellectual property of the provider (208.x.x.x), allowing more traffic in and out of the same interface for traffic of U-turn.
Here's what you need to set up:
permit same-security-traffic intra-interface
nat-to-vendor ip 10.4.4.0 access list permit 255.255.255.224 host 208.x.x.x
NAT (outside) 101-list of nat-to-vendor access
The foregoing will allow VPN pool to be coordinated to your ASA outside the ip address of the interface when accessing the seller (208.x.x.x).
1 small correction to your ACL split tunnel:
-The following line is incorrect and should be deleted in the tunnel of split ACL:
Access extensive list ip 10.4.4.0 VPN_splitunnel allow 255.255.255.224 all
(As 10.4.4.0/27 is your pool of Client VPN, you do not add these subnet to your list of split tunnel. List of Split tunnel are only the network that you are difficult to access and sent through your VPN tunnel).
Hope that helps.
-
ASA 5505 AnyConnect 8.2 - Can't access and inside services
Hello
I have configured AnyConnect to use a subnet of 10.0.7.0/24 for its DHCP pool. I can connect to the ASA very well, but I can't access internal services on my subnet 10.0.5.0/24 which is my INNER interface vlan subnet. I configure NAT for exemption rule:
allowed to Access-list inside_nat0_outbound line 2 extended 10.0.5.0 ip 255.255.255.0 Any-Connect-Pool-10-0-7-0 object-group
AnyConnect is set to ignore all the ACL rules through the sysopt permit vpn connection.
I don't know if I'm supposed to create another path to the VPN subnet or what exactly. When I ping my VPN subnet to a client on the subnet of the INTERIOR, I see ICMP traffic flowing through the FW, but I didn't get any answer. I do not split-tunnleing and I can not connect to internet either after establishing a VPN connection.
Thanks in advance for the help.
Hello
You must ensure that the following setting is enabled
permit same-security-traffic intra-interface
You should also make sure PAT configured for your Pool of VPN Dynamics
If your current dynamic PAT for internal users would
Global 1 interface (outside)
NAT (inside) 1 10.0.5.0 255.255.255.0
Then you must add
NAT (outside) 1 10.0.7.0 255.255.255.0
Hope this helps
Remember to mark a reply as the answer if it answered your question.
Feel free to ask more if necessary
-Jouni
-
Configuration of the ASA is below!
ASA Version 9.1 (1)
!
ASA host name
domain xxx.xx
names of
local pool VPN_CLIENT_POOL 192.168.12.1 - 192.168.12.254 255.255.255.0 IP mask
!
interface GigabitEthernet0/0
nameif inside
security-level 100
192.168.11.1 IP address 255.255.255.0
!
interface GigabitEthernet0/1
Description Interface_to_VPN
nameif outside
security-level 0
IP 111.222.333.444 255.255.255.240
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
192.168.5.1 IP address 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
www.ww domain name
permit same-security-traffic intra-interface
the object of the LAN network
subnet 192.168.11.0 255.255.255.0
LAN description
network of the SSLVPN_POOL object
255.255.255.0 subnet 192.168.12.0
VPN_CLIENT_ACL list standard access allowed 192.168.11.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
management of MTU 1500
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 711.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (exterior, Interior) static source SSLVPN_POOL SSLVPN_POOL static destination LAN LAN
Route outside 0.0.0.0 0.0.0.0 111.222.333.443 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
WebVPN
list of URLS no
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
AAA authentication http LOCAL console
LOCAL AAA authorization exec
Enable http server
http 192.168.5.0 255.255.255.0 management
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec pmtu aging infinite - the security association
Crypto ca trustpoint ASDM_TrustPoint5
Terminal registration
E-mail [email protected] / * /
name of the object CN = ASA
address-IP 111.222.333.444
Configure CRL
Crypto ca trustpoint ASDM_TrustPoint6
Terminal registration
domain name full vpn.domain.com
E-mail [email protected] / * /
name of the object CN = vpn.domain.com
address-IP 111.222.333.444
pair of keys sslvpn
Configure CRL
trustpool crypto ca policy
string encryption ca ASDM_TrustPoint6 certificates
Telnet timeout 5
SSH 192.168.11.0 255.255.255.0 inside
SSH timeout 30
Console timeout 0
No ipv6-vpn-addr-assign aaa
no local ipv6-vpn-addr-assign
192.168.5.2 management - dhcpd addresses 192.168.5.254
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL-trust outside ASDM_TrustPoint6 point
WebVPN
allow outside
CSD image disk0:/csd_3.5.2008-k9.pkg
AnyConnect image disk0:/anyconnect-win-3.1.04066-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client
internal VPN_CLIENT_POLICY group policy
VPN_CLIENT_POLICY group policy attributes
WINS server no
value of server DNS 192.168.11.198
VPN - 5 concurrent connections
VPN-session-timeout 480
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_CLIENT_ACL
myComp.local value by default-field
the address value VPN_CLIENT_POOL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 20
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect client of dpd-interval 30
dpd-interval gateway AnyConnect 30
AnyConnect dtls lzs compression
AnyConnect modules value vpngina
value of customization DfltCustomization
internal IT_POLICY group policy
IT_POLICY group policy attributes
WINS server no
value of server DNS 192.168.11.198
VPN - connections 3
VPN-session-timeout 120
Protocol-tunnel-VPN-client ssl clientless ssl
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_CLIENT_ACL
field default value societe.com
the address value VPN_CLIENT_POOL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 20
AnyConnect dtls lzs compression
value of customization DfltCustomization
username vpnuser password PA$ encrypted $WORD
vpnuser username attributes
VPN-group-policy VPN_CLIENT_POLICY
type of remote access service
Username vpnuser2 password PA$ encrypted $W
username vpnuser2 attributes
type of remote access service
username admin password ADMINPA$ $ encrypted privilege 15
VPN Tunnel-group type remote access
General-attributes of VPN Tunnel-group
address VPN_CLIENT_POOL pool
Group Policy - by default-VPN_CLIENT_POLICY
VPN Tunnel-group webvpn-attributes
the aaa authentication certificate
enable VPN_to_R group-alias
type tunnel-group IT_PROFILE remote access
attributes global-tunnel-group IT_PROFILE
address VPN_CLIENT_POOL pool
Group Policy - by default-IT_POLICY
tunnel-group IT_PROFILE webvpn-attributes
the aaa authentication certificate
enable IT Group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
: end
Hello
Here's what you'll need:
permit same-security-traffic intra-interface
VPN_CLIENT_ACL standard access list allow 192.168.12.0 255.255.255.0
destination NAT (outside, outside) SSLVPN_POOL SSLVPN_POOL SSLVPN_POOL SSLVPN_POOL static static source
Patrick
-
Cisco ASA 5515 - Anyconnect users can connect to ASA, but cannot ping inside the local IP address
Hello!
I have a 5515 ASA with the configuration below. I have configure the ASA as remote access with anyconnect VPN server, now my problem is that I can connect but I can not ping.
ASA Version 9.1 (1)
!
ASA host name
domain xxx.xx
names of
local pool VPN_CLIENT_POOL 192.168.12.1 - 192.168.12.254 255.255.255.0 IP mask
!
interface GigabitEthernet0/0
nameif inside
security-level 100
192.168.11.1 IP address 255.255.255.0
!
interface GigabitEthernet0/1
Description Interface_to_VPN
nameif outside
security-level 0
IP 111.222.333.444 255.255.255.240
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
192.168.5.1 IP address 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
www.ww domain name
permit same-security-traffic intra-interface
the object of the LAN network
subnet 192.168.11.0 255.255.255.0
LAN description
network of the SSLVPN_POOL object
255.255.255.0 subnet 192.168.12.0
VPN_CLIENT_ACL list standard access allowed 192.168.11.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
management of MTU 1500
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 711.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (exterior, Interior) static source SSLVPN_POOL SSLVPN_POOL static destination LAN LAN
Route outside 0.0.0.0 0.0.0.0 111.222.333.443 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
WebVPN
list of URLS no
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
AAA authentication http LOCAL console
LOCAL AAA authorization exec
Enable http server
http 192.168.5.0 255.255.255.0 management
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec pmtu aging infinite - the security association
Crypto ca trustpoint ASDM_TrustPoint5
Terminal registration
E-mail [email protected] / * /
name of the object CN = ASA
address-IP 111.222.333.444
Configure CRL
Crypto ca trustpoint ASDM_TrustPoint6
Terminal registration
domain name full vpn.domain.com
E-mail [email protected] / * /
name of the object CN = vpn.domain.com
address-IP 111.222.333.444
pair of keys sslvpn
Configure CRL
trustpool crypto ca policy
string encryption ca ASDM_TrustPoint6 certificates
Telnet timeout 5
SSH 192.168.11.0 255.255.255.0 inside
SSH timeout 30
Console timeout 0
No ipv6-vpn-addr-assign aaa
no local ipv6-vpn-addr-assign
192.168.5.2 management - dhcpd addresses 192.168.5.254
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL-trust outside ASDM_TrustPoint6 point
WebVPN
allow outside
CSD image disk0:/csd_3.5.2008-k9.pkg
AnyConnect image disk0:/anyconnect-win-3.1.04066-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client
internal VPN_CLIENT_POLICY group policy
VPN_CLIENT_POLICY group policy attributes
WINS server no
value of server DNS 192.168.11.198
VPN - 5 concurrent connections
VPN-session-timeout 480
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_CLIENT_ACL
myComp.local value by default-field
the address value VPN_CLIENT_POOL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 20
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect client of dpd-interval 30
dpd-interval gateway AnyConnect 30
AnyConnect dtls lzs compression
AnyConnect modules value vpngina
value of customization DfltCustomization
internal IT_POLICY group policy
IT_POLICY group policy attributes
WINS server no
value of server DNS 192.168.11.198
VPN - connections 3
VPN-session-timeout 120
Protocol-tunnel-VPN-client ssl clientless ssl
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_CLIENT_ACL
field default value societe.com
the address value VPN_CLIENT_POOL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 20
AnyConnect dtls lzs compression
value of customization DfltCustomization
username vpnuser password PA$ encrypted $WORD
vpnuser username attributes
VPN-group-policy VPN_CLIENT_POLICY
type of remote access service
Username vpnuser2 password PA$ encrypted $W
username vpnuser2 attributes
type of remote access service
username admin password ADMINPA$ $ encrypted privilege 15
VPN Tunnel-group type remote access
General-attributes of VPN Tunnel-group
address VPN_CLIENT_POOL pool
Group Policy - by default-VPN_CLIENT_POLICY
VPN Tunnel-group webvpn-attributes
the aaa authentication certificate
enable VPN_to_R group-alias
type tunnel-group IT_PROFILE remote access
attributes global-tunnel-group IT_PROFILE
address VPN_CLIENT_POOL pool
Group Policy - by default-IT_POLICY
tunnel-group IT_PROFILE webvpn-attributes
the aaa authentication certificate
enable IT Group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
: end
Help me please! Thank you!
Hello
Please set ACLs to allow ICMP between these two subnets (192.168.11.0 and 192.168.12.0) and check. It should ping. Let me know if it does not work.
Thank you
swap
-
ASA 5505 AnyConnect Client issues
I have a client who is able to use ordinary VPN client, but one of the lawyers bought a new laptop with Windows 8 and must now AnyConnect. I opened the customer and you connect, but it says that it cannot open a session with the following messages:
AnyConnect was not able to establish a connection with the specified secure gateway. Please try again.
Then I click OK and I get:
The secure gateway rejected the connection attempt. A new connection attempt the same or another secure gateway is required, which requires authorization.
The following message was received from the secué Bridge: no address available for an SVC connection.
I have the config following running:
: Saved
:
ASA Version 8.2 (5)
!
ASA host name
domain.local domain name
activate 8Ry2Yjt7RRXU24 encrypted password
vCGdNOPVyz.a0N encrypted passwd
names of
name 10.10.10.10 DG-Commcast Commcast Default Gateway description
name 20.20.20.20 DG-FirstCom description first default gateway of Communications
name 10.10.10.11 ASA-outside
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
switchport access vlan 12
!
interface Ethernet0/2
Speed 100
full duplex
!
interface Ethernet0/3
switchport access vlan 22
Speed 100
full duplex
!
interface Ethernet0/4
switchport access vlan 22
!
interface Ethernet0/5
switchport access vlan 22
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
the IP 192.168.0.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
address IP ASA-outside 255.255.255.248
!
interface Vlan12
nameif backup
security-level 0
IP 168.93.174.130 255.255.255.248
!
interface Vlan22
nameif phones
security-level 100
address 192.168.3.1 IP 255.255.255.0
!
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT
DNS lookup field inside
DNS domain-lookup outside
backup DNS domain-lookup
DNS domain-lookup phones
DNS server-group DefaultDNS
domain.local domain name
object-group service RDP tcp - udp
EQ port 3389 object
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service LogMeIn tcp
Globe description
port-object eq 2002
DM_INLINE_TCP_1 tcp service object-group
Group-object LogMeIn
port-object eq www
EQ object of the https port
outside_access_in list extended access allowed object-group TCPUDP any host 50,76
. 252.34 object group RDP
outside_access_in list extended access permit tcp any interface phones object-gr
OUP DM_INLINE_TCP_1
outside_access_in list extended access permit icmp any one
outside_access_in list extended access permit tcp any host ASA-outside eq ssh
inside_access_in of access allowed any ip an extended list
VPNClient_splitTunnelAcl list standard access allowed 192.168.0.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access any 192.168.10.0 255.255.255
.128
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 19
2.168.10.0 255.255.255.128
VPNClient_splitTunnelAcl_1 list standard access allowed 192.168.0.0 255.255.255.0
backup_access_in list extended access permit icmp any one
pager lines 24
Enable logging
list of logging message BackupLineAlert 622001
debug logging in buffered memory
exploitation forest asdm warnings
exploitation forest mail BackupLineAlert
address record [email protected] / * /
exploitation forest-address recipient [email protected] / * / level of information
exploitation forest-address recipient [email protected] / * / level of information
Within 1500 MTU
Outside 1500 MTU
backup of MTU 1500
MTU 1500 phones
local pool VPNDHCP 192.168.10.50 - 192.168.10.80 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ICMP allow any backup
ICMP allow all phones
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
Global 1 interface (backup)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 0 192.168.10.0 255.255.255.128
NAT (inside) 1 192.168.0.0 255.255.255.0
NAT (inside) 0 0.0.0.0 0.0.0.0
NAT (phones) 1 0.0.0.0 0.0.0.0
public static 50.76.252.34 (Interior, exterior) 192.168.0.254 netmask 255.255.255.255
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Access-group backup_access_in in the backup of the interface
Route outside 0.0.0.0 0.0.0.0 DG - Commcast 128 Track1
Backup route 0.0.0.0 0.0.0.0 DG-FirstCom 255
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
Enable http server
http 192.168.0.0 255.255.255.0 inside
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
No vpn sysopt connection permit
monitor SLA 123
type echo protocol ipIcmpEcho 8.8.8.8 outside interface
NUM-package of 3
Timeout 10000
frequency 15
Annex ALS life monitor 123 to always start-time now
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-AES-128
SHA - ESP - AES - 128 - MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256
-MD5-ESP-3DES-MD5 ESP-3DES-SHA SHA-DES-ESP ESP - THE - MD5
backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
backup of crypto backup_map interface card
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
Crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca 6ecc7aa5a7032ebcf4e952d491
308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
6c2527b9 deb78458 c61f381e a4c4cb66
quit smoking
crypto ISAKMP allow outside
ISAKMP crypto enable backup
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
!
track 1 rtr 123 accessibility
VPN-addr-assign local reuse / time 5
Telnet 192.168.0.0 255.255.255.0 inside
Telnet 192.168.10.0 255.255.255.0 inside
Telnet timeout 20
SSH 192.168.0.0 255.255.255.0 inside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 0.0.0.0 0.0.0.0 backup
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 192.168.0.150 - 192.168.0.180 inside
dhcpd 192.168.0.254 dns 8.8.8.8 interface inside
lease interface 604800 dhcpd inside
dhcpd domain.local domain inside interface
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
a statistical threat detection tcp intercept rate-interval 30 rate burst-400 averag
e-rate 200
NTP server 208.66.175.36 prefer external source
NTP server 173.14.55.9 source outdoors
WebVPN
allow outside
enable backup
SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
SVC profiles AnyConnectProfile disk0: / anyconnectprofile.xml
enable SVC
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal VPNClient group strategy
attributes of VPNClient-group policy
value of DNS 192.168.0.254 Server 8.8.8.8
Protocol-tunnel-VPN IPSec svc webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPNClient_splitTunnelAcl_1
domain.local value by default-field
WebVPN
profiles of SVC value AnyConnectProfile
username screams password encrypted BQd7EeZN.0hvT privilege 0
attributes of cries of username
type of service admin
tony U/UxEH5l0w5Q encrypted privilege 15 password username
nancy lAnhc/SvNNSSR password user name encrypted privilege 0
tunnel-group VPNClient type remote access
tunnel-group VPNClient-global attributes
address VPNDHCP pool
Group Policy - by default-VPNClient
tunnel-group VPNClient ipsec-attributes
pre-shared key *.
!
!
Server SMTP 192.168.0.254
context of prompt hostname
anonymous reporting remote call
Cryptochecksum:de5e8aec62853af27945c52bf36
: end
The version of the client AnyConnect should be identical to the version that is loaded on the ASA? I use the 3.0.5080 client and the parameters of the client AnyConnect on the SAA's anconnect-win - 2.5.201 - kr.pkg
Thanks for the help!
Tony
The error message gives a clue:
No address available for SVC connection
The client cannot work without an assigned IP address. As you have assigned a pool to the tunnel group, I suppose that the customer is not to connect to the desired group, but for the default group. At least, I see nothing in the config that gives the customer the right group.
Try the following:
WebVPN
tunnel-group-list activate
tunnel-group VPNClient webvpn-attributes
enable Group VPNClient-alias
With it, you get a drop-down menu in the client to choose the right tunnel-group.
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
Internet connections ASA 5505 - two
Is Hi possible to configure an ASA 5505 with two internet connections? One dedicated to the VPN and the other for Internet access only.
If you have an example to share.
Thank you very much
David
I see that you have a static route to 186.125.164.178, if you only test card crypto 2, right?
Your nat (inside) 0 uses ACL inside_nat0_outbound_1 which doesn't seem to have the exclusion for 10.5.3.0/24 remote network.
-
HI Experts,
Can you please give me an idea on what this module IDS/IPS for ASA 5505?
How much does it cost? How to install and configure to work with ASA 5505?
We have also a few site to site of ASA 5505 VPN configuration. This would affect somehow?
Thank you very much
ANUP
ANUP-
You should be able to find the links that I provided for you with a general search on Cisco's Web site for 'ssc-5' and 'installation' and 'configure '.
No, you should still ASA terminate Internet access. You want to have the SSC-5 module (IPS) to monitor the interfaces from the INSIDE, (always wanting to make IDS/IPS inside a firewall). This way you can see the traffic after it has been decrypted on your VPN, and after the traffic has been filtered to your firewall rules.
-Bob
-
Unable to connect to ASA 5505 with AnyConnect after upgrade to 8.2
I just bought a license of VPN AnyConnect Essentials for my ASA 5505. I had to spend to 8.2 ASA.
Now that I updated and installed the license, the AnyConnect client will connect is no longer. It gives the following error: "failed to process the response.
You can provide any help would be appreciated. I am pleased to provide you with the configuration information that might be useful if you can provide the CLI commands, you want that I run.
Looks like he doesn't like THEM too, you can change the encryption algorithm to 'not' include in your strategy:
3des-sha1-aes128-sha1 sha1 aes256 encryption SSL
In general is not very safe anyway, and the choice of encryption above will provide you with the best encryption strategy.
Hope that helps.
-
ASA 5505 TFTP to one subnet to another creates the empty file
Hello world
The Cisco ASA 5505 does not seem to allow the TFTP connection between 192.168.5.103/24 and 192.168.10.202/24. TFTP is normally used in the same subnet, but not in my case. I have a DHCP relay that works, but when I use the free tool from one side to the other tool TFTPD TFTPD, it creates an empty file. Anyone know what config I could be missing in my Cisco ASA?
Thank you in advance.
---
Nathan
Hi Jonathan,.
1. check that tftp server is using the correct interface of the given subnet. (under Server Interfaces on tftpd32)
2. check if the default gateway have a correct route to the TFTP server.
3 make sure that TFTP server can reach the subnet of the client.
HTH
-
VPN Tunnel access to several subnets ASA 5505
Greetings,
We spent a little time trying to configure our ASA 5505 in order to TUNNEL into several different subnets. Subnets include 192.168.1.0 / 192.168.2.0 / 192.168.10.0
Someone is about to review this setup running and indicate where we have gone wrong. When I connect via the VPN Client, I can access the 192.168.1.0 network, no problem. But fail to reach the other two. Thank you very much.
Output from the command: 'show running-config '.
: Saved
:
ASA Version 8.2 (5)
!
hostname BakerLofts
activate kn7RHw13Elw2W2eU encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
switchport access vlan 12
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.254 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 74.204.54.4 255.255.255.248
!
interface Vlan12
nameif Inside2
security-level 100
IP address 192.168.10.254 255.255.255.0
!
passive FTP mode
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
vpn_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
outside_access_in of access allowed any ip an extended list
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.3.0 255.255.255.0
Inside2_access_in of access allowed any ip an extended list
permit Inside2_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.3.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 Inside2
IP local pool vpn 192.168.3.1 - 192.168.3.254 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 0 192.168.3.0 255.255.255.0 outside
NAT (Inside2) 0-list of access Inside2_nat0_outbound
NAT (Inside2) 1 0.0.0.0 0.0.0.0
Access-group outside_access_in in interface outside
Access-group Inside2_access_in in the interface Inside2
Route outside 0.0.0.0 0.0.0.0 74.204.54.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
AAA authentication LOCAL telnet console
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
Crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65
74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332
68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329
302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f
63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d
010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597
a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1
6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b
c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603
445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04
1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
6c2527b9 deb78458 c61f381e a4c4cb66
quit smoking
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.168.1.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal vpn group policy
attributes of vpn group policy
value of server DNS 8.8.8.8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpn_splitTunnelAcl
username, password samn aXJbUl92B77AGcc. encrypted privilege 0
samn attributes username
Strategy-Group-VPN vpn
username password encrypted QUe2MihLFbj2.Iw0 privilege 0 jmulwa
username jmulwa attributes
Strategy-Group-VPN vpn
jangus Uixpk4uuyEDOu9eu username encrypted password
username jangus attributes
Strategy-Group-VPN vpn
vpn tunnel-group type remote access
VPN tunnel-group general attributes
vpn address pool
Group Policy - by default-vpn
Tunnel vpn ipsec-attributes group
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
anonymous reporting remote call
Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
: end
I see two problems:
1. your ASA has not an interior road to the Incas inside networks. You must add:
Route inside 192.168.2.0 255.255.255.0
Route inside 192.168.10.0 255.255.255.0
.. .specifying your gateway address of these networks.
2. the statement "access-list standard vpn_splitTunnelAcl permit 192.168.1.0 255.255.255.0" sends only a route for 192.168.1.0/24 to your customer. You need to add entries for the other two networks.
Maybe you are looking for
-
Satellite Pro L300 - Player DVD 10 on Vista error code.
Can not see the DVD drive in 'my computer' in Device Manager its display in car but with yellow triangle, after watching the news, the State of the device is "this device cannot start. (Code 10) "tried to restart 2 times. It's does not.Also the drive
-
I have an old scanner HP6200c can I get the drivers using windows 7
Can someone help me find drivers for an old HP 6200 c scanner
-
HP Pavilion a767c Windows XP I have some stuff on my pc that I can't remove. It is not in my "Add or remove a program. How I can remove them.
-
When windows starts the user name is not displayed, almost all programs do not work, or I get a message saying that they have permission to run the service, sometimes windows not loading some programs of initialization and I can't turn off the pc by
-
Windows says dell somehow prevents me to save my copy of windows after a reinstall
My hard drive died so I reinstalled my copy of windows 7 64-bit edition Home premium, but I can't seem to register even though I'm pretty sure that the code. (The laptop is more than 3 years old and the sticker has rubbed off a bit) I talked to windo