ASA 5505 ASDM VPN connection problem

Similar Questions

• ASA 5505 ipsec vpn connection fails

  Hello

  I'm trying to configure a Cisco ASA 5505 for Remote Clients.

  I use the ASDM interface and used assistants start and ipsec for my setup, but im hit a stumbling block.

  To last make it work 2 days I have tried a number of configuration changes to try to make this work but didn't, so I did a factory reset and passed by the assistants, once again, I have a clean Setup that I hope someone can help me.

  Currently I have an IP public static 81.137.x.x and I use a Netgear ADSL router, which transfers (UDP 500) VPN traffic to 192.168.171.35 (port wan on the ASA 5505).

  The Cisco ASA has a default address of 192.168.1.1

  I use the Cisco Client 5.0.06.0160.

  I have configured the client to use authentication group with the same credentials as configuration through the wizard and im using Transparent Tunneling IPSec over UDP.

  I have attached 2 documents

  running_config.txt - what is shows the current configuration of ASA

  Journal - View.txt - display of error messages displayed in the real-time log viewer when I try to connect from the remote client.

  I'm not sure if I need to do on the other that additional configurations for my setup simply run the wizards.

  Any help would be appreciated.

  Thank you

  Hello Philippe,

  According to the lines in the journal, there is a problem of routing for ip vpn applicant address. ASA couldn't find the definition of route suitable for the return traffic. Add a default route to unknown destinations could solve this problem. As I see you are using modem netgear as a default gateway for your ASA. I write example of command line for this purpose.

  Route outside 0.0.0.0 0.0.0.0 NetGear_LAN_IP_Address 1

  Ufuk Güler

• ASA 5505 IPSEC VPN connected but cannot access the local network

  ASA: 8.2.5

  ASDM: 6.4.5

  LAN: 10.1.0.0/22

  Pool VPN: 172.16.10.0/24

  Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

  I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

  Here is my setup, wrong set up anything?

  ASA Version 8.2 (5)

  !

  hostname asatest

  domain XXX.com

  activate 8Fw1QFqthX2n4uD3 encrypted password

  g9NiG6oUPjkYrHNt encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.1.1.253 255.255.252.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  address IP XXX.XXX.XXX.XXX 255.255.255.240

  !

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  DNS server-group DefaultDNS

  domain vff.com

  vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

  access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

  pager lines 24

  Enable logging

  timestamp of the record

  logging trap warnings

  asdm of logging of information

  logging - the id of the device hostname

  host of logging inside the 10.1.1.230

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-server protocol nt AD

  AAA-server host 10.1.1.108 AD (inside)

  NT-auth-domain controller 10.1.1.108

  Enable http server

  http 10.1.0.0 255.255.252.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 10.1.0.0 255.255.252.0 inside

  SSH timeout 20

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group vpntest strategy

  Group vpntest policy attributes

  value of 10.1.1.108 WINS server

  Server DNS 10.1.1.108 value

  Protocol-tunnel-VPN IPSec l2tp ipsec

  disable the password-storage

  disable the IP-comp

  Re-xauth disable

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpntest_splitTunnelAcl

  value by default-domain XXX.com

  disable the split-tunnel-all dns

  Dungeon-client-config backup servers

  the address value vpnpool pools

  admin WeiepwREwT66BhE9 encrypted privilege 15 password username

  username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

  the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

  tunnel-group vpntest type remote access

  tunnel-group vpntest General attributes

  address vpnpool pool

  authentication-server-group AD

  authentication-server-group (inside) AD

  Group Policy - by default-vpntest

  band-Kingdom

  vpntest group tunnel ipsec-attributes

  pre-shared-key BEKey123456

  NOCHECK Peer-id-validate

  !

  !

  privilege level 3 mode exec cmd command perfmon

  privilege level 3 mode exec cmd ping command

  mode privileged exec command cmd level 3

  logging of the privilege level 3 mode exec cmd commands

  privilege level 3 exec command failover mode cmd

  privilege level 3 mode exec command packet cmd - draw

  privilege show import at the level 5 exec mode command

  privilege level 5 see fashion exec running-config command

  order of privilege show level 3 exec mode reload

  privilege level 3 exec mode control fashion show

  privilege see the level 3 exec firewall command mode

  privilege see the level 3 exec mode command ASP.

  processor mode privileged exec command to see the level 3

  privilege command shell see the level 3 exec mode

  privilege show level 3 exec command clock mode

  privilege exec mode level 3 dns-hosts command show

  privilege see the level 3 exec command access-list mode

  logging of orders privilege see the level 3 exec mode

  privilege, level 3 see the exec command mode vlan

  privilege show level 3 exec command ip mode

  privilege, level 3 see fashion exec command ipv6

  privilege, level 3 see the exec command failover mode

  privilege, level 3 see fashion exec command asdm

  exec mode privilege see the level 3 command arp

  command routing privilege see the level 3 exec mode

  privilege, level 3 see fashion exec command ospf

  privilege, level 3 see the exec command in aaa-server mode

  AAA mode privileged exec command to see the level 3

  privilege, level 3 see fashion exec command eigrp

  privilege see the level 3 exec mode command crypto

  privilege, level 3 see fashion exec command vpn-sessiondb

  privilege level 3 exec mode command ssh show

  privilege, level 3 see fashion exec command dhcpd

  privilege, level 3 see the vpnclient command exec mode

  privilege, level 3 see fashion exec command vpn

  privilege level see the 3 blocks from exec mode command

  privilege, level 3 see fashion exec command wccp

  privilege see the level 3 exec command mode dynamic filters

  privilege, level 3 see the exec command in webvpn mode

  privilege control module see the level 3 exec mode

  privilege, level 3 see fashion exec command uauth

  privilege see the level 3 exec command compression mode

  level 3 for the show privilege mode configure the command interface

  level 3 for the show privilege mode set clock command

  level 3 for the show privilege mode configure the access-list command

  level 3 for the show privilege mode set up the registration of the order

  level 3 for the show privilege mode configure ip command

  level 3 for the show privilege mode configure command failover

  level 5 mode see the privilege set up command asdm

  level 3 for the show privilege mode configure arp command

  level 3 for the show privilege mode configure the command routing

  level 3 for the show privilege mode configure aaa-order server

  level mode 3 privilege see the command configure aaa

  level 3 for the show privilege mode configure command crypto

  level 3 for the show privilege mode configure ssh command

  level 3 for the show privilege mode configure command dhcpd

  level 5 mode see the privilege set privilege to command

  privilege level clear 3 mode exec command dns host

  logging of the privilege clear level 3 exec mode commands

  clear level 3 arp command mode privileged exec

  AAA-server of privilege clear level 3 exec mode command

  privilege clear level 3 exec mode command crypto

  privilege clear level 3 exec command mode dynamic filters

  level 3 for the privilege cmd mode configure command failover

  clear level 3 privilege mode set the logging of command

  privilege mode clear level 3 Configure arp command

  clear level 3 privilege mode configure command crypto

  clear level 3 privilege mode configure aaa-order server

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

  : end

  Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

  The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

  On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.

• ASA 5510 IPSEC VPN connection problem

  Hello

  We have an ASA 5510 (ASA version 8.0) of remote access VPN configured and works most of the time, but there is a problem when you have more than one client that connects to the same office remotely.  When the first VPN client is connected to the remote desktop, everything works fine, but when the second client connects to the VPN, it connects fine but do not get any traffice return to customer.  I can see under monitor-> statistical VPN-> Sessions-> remote access-> Rx Bytes is 0. Both connections are from the same public IP address of the remote desktop.  I changed some settings on NAT - T and a few other things, but without success.

  Could someone help me please how to fix this?

  Thank you very much.

  Make sure that customers use because that probably her you're not. (default value is NAT - T).

  Federico.

• ASA easy VPN connection problem

  Hi guys,.

  I configured easy VPN between 5510 and 5505. Every thing seems fine, however, if there is no traffic in the tunnel in the next few hours, I can not initial 5510 5505 (customer) traffic. But if I first traffice 5505, there is no problem.

  Anyone know why?

  Thank you

  Hello

  This is normal behavior, it is part of the easy vpn functionality. The 5505 will act as a remote for the 5510 vpn client. This isn't like a site to site vpn or both ends know the IP address of the remote peer, and so that each peer can initiate the connection, here the 5510 don't know on the network and 5505 IP when it will connect via the easy VPN.

  If you want the tunnel to be put in place at both ends, I would say that you are using a classic site-to-site connection as described here:

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/Getting_started/ASA5505/quick/guide/SITESITE.html

  I hope this helps.

  Kind regards
  Bastien

• Cisco ASA 5505 remote VPN access to the local network

  I have installed two ASA 5505 VPN site to site that works perfectly.  Now, I also need to have 1 customer site to remote access VPN with Cisco VPN dialer.  I can get the VPN dialer to connect the VPN and get a VPN IP address, but I do not have access to the remote network.  can someone take a look and see what I'm missing?  I have attached the ASA running config.

  Apologize for the misunderstanding.

  To access the remote vpn client 10.10.100.x subnet, the vpn-filter ACL is the opposite.

  Please please share the following ACL:

  FROM: / * Style Definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  outside_cryptomapVPN list of allowed ip extended access any 10.10.20.0 255.255.255.224

  TO:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-marge-haut : 0 cm ; mso-para-marge-droit : 0 cm ; mso-para-marge-bas : 10.0pt ; mso-para-marge-gauche : 0 cm ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  outside_cryptomapVPN to access extended list ip 10.10.20.0 allow 255.255.255.224 all

  Hope that helps.

• VPN connection problem: keep connection

  I'm having a problem with the maintenance of VPN connection. I connect okay but the line VPN disconnects after about 2 minutes each time.  I use XP Professional V2002, Service Pack 3.  I have disabled the WIndows firewall, as I have F-Secure software suite with its active firewall.  I connect laptop wireless via a Belkin router.  I had no problem for months up until August when suddenly this problem appeared.  I have disabled firewall F-secure, but that did not help. I also disabled the firewall on the router, but again without success.  Can you please help?

  Hi Rashmis,

  Thanks for visiting the site of the community of Microsoft Windows XP. The question you have posted is related to VPN issues and would be better suited to the Technet community. Please visit the link below to find a community that will provide the support you want. http://social.technet.Microsoft.com/forums/en/categories/

  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• ASA 5505 SSL VPN license update

  Hi all.

  Our ASA 5505 with DATABASE default license allowing only 10 simultaneous vpn sessions (including 2 Anyconnect + IPsec). attached a TXT file with the license information. This Firewall is's use only for vpn access, and we less vpn tunnel vpn IPSec-L2L, anyconnect client SSL and IPSec client access configurations vpn to the top and race walk,.

  We are in terms of upgrading vpn license to archive IPSec 10 and 10 Anyconnect and 1 anyconect mobile VPN sessions in time. so my questions are;

  1. can I buy "ASA5500-SSL-10 =" accounting and to upgrade our ASA 5505 without having to buy "L-ASA5505-SEC-PL =" license of pus of security.

  2. asa use to upgrade only Anyconnect SSL vpn license while keeping 10 vpn IPSec comes with the base license.

  Thank you & you expects value comment

  Thank you

  JCK

  1. Yes.

  2.Yes.

  If you want to keep Clientless SSL VPN you do not want to continue with the addition of the ASA5500-SSL-10 = part. If you can do without client (including the conversion the two existing ones), more economically, you can opt for Security Plus and AnyConnect Essentials licenses. (US$ 800 vs price $1250).

  In both cases, the Mobile requires the AnyConnect Mobile (ASA-AC-M-5505) license.

• VPN connection problems...

  I don't know what is happening or what Miss me...

  I set up a vpn connection to my remote offices with a 5505.  My main office, I have a 5510.

  My remote offices, I can PING my main Office Server.  However, when I go to set up a VPN through windows network sharing Center I can't get the connection to connect...

  Am I doing something wrong or what step am I missing?

  Thank you!!

  Can you try to add this:

  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface

  I'd put it on two unless you have a reason not to.  If there is no love after that we will break down the pppoe and vpn configuration.

  Matt

• Cisco ASA 5505 - Configuration VPN

  I'm trying to configure a VPN connection to allow customers access to the internal network. I have tried to use time Wizard VPN & repeatedly but customer connect but can get out to the internet and communicate with any host on the network. I tried to use a vpn in the 192.x.x.x or 10.10.1.X network dhcp pool but no luck.

  Comments or suggestions appreciated.

  What is the reason for these commands?

  NAT (outside) 0-list of access policyPAT

  NAT (outside) 5 10.10.1.0 255.255.255.0

  If this isn't spicific reason remove

  and put the following command:

  Permitted connection ipsec sysopt

  in global configuration mode to enable the VPN traffic to work around interface access lists

  Good luck

  If useful rates

• Cisco ASA 5505 - capable to connect to VPN - access forbidden inside

  Hello

  I tried to set up a virtual private network for weeks, I can connect to the public IP address of the ASA, but I can't reach anything behind Cisco.

  I give you my config:

  ASA Version 8.2 (5)
  !
  host name asa
  sarg domain name * .net
  activate the encrypted password of Z4K16OvBr0J5Dj/2
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  passive FTP mode
  DNS server-group DefaultDNS
  domain sargicisco.net
  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.0 255.255.255.0
  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
  Remote_Sargi_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0
  pager lines 24
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  mask 192.168.254.1 - 192.168.254.10 255.255.255.0 IP local pool SAVPN_Pool
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  inside crypto map inside_map interface
  crypto ISAKMP allow outside
  crypto ISAKMP allow inside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  VPN-addr-assign local reuse / time 5
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.5 - 192.168.1.36 inside
  Wis field dhcpd * .net interface inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  allow outside
  allow inside
  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
  enable SVC
  tunnel-group-list activate
  attributes of Group Policy DfltGrpPolicy
  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
  internal Remote_Sargi group strategy
  attributes of Group Policy Remote_Sargi
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Remote_Sargi_splitTunnelAcl
  sargicisco.NET value by default-field
  username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
  username kevin attributes
  VPN-group-policy DfltGrpPolicy
  type tunnel-group SAVPN remote access
  attributes global-tunnel-group SAVPN
  address pool SAVPN_Pool
  tunnel-group SAVPN webvpn-attributes
  enable SAVPN group-alias
  allow group-url https://82.228.XXX.XXX/SAVPN
  type tunnel-group Remote_Sargi remote access
  attributes global-tunnel-group Remote_Sargi
  address pool SAVPN_Pool
  Group Policy - by default-Remote_Sargi
  IPSec-attributes tunnel-group Remote_Sargi
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:387a6e260247a545f4df0d3f28ba58c5
  : end

  Thank you

  Hello

  Could you remove this statement and add the last:

  no nat (inside) 0-list of access inside_nat0_outbound

  ADD: nat (inside) 0 access-list sheep - in

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• ASA 5505. VPN Site-to-Site does not connect!

  Hello!
  Already more than a week there, as we had a new channel of communication of MGTSa (Ontario terminal Sercomm RV6688BCM, who barely made in the 'bridge' - had to do the provider in order to receive our white Cisco Ip address), and now I train as well more that one week to raise between our IKEv1 IPsec Site-to-Site VPN tunnel closes offices.
  Configurable and use the wizard in ASDM and handles in the CLI, the result of a year, the connection does not rise.
  Cisco version 9.2 (2), the image of the Cisco asa922 - k8.bin, Security Plus license version, version 7.2 AMPS (2).
  What I'll never know...
  Debugging and complete configuration enclose below.
  Help, which can follow any responses, please! I was completely exhausted!

  Config:

  Output of the command: "sh run".

  : Saved
  :
  : Serial: XXXXXXXXXXXX
  : Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor
  :
  ASA Version 9.2 (2)
  !
  hostname door-71
  activate the encrypted password of F6OJ0GOws7WHxeql
  names of
  IP local pool vpnpool 10.1.72.100 - 10.1.72.120 mask 255.255.255.0
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 10.1.72.254 255.255.255.0
  !
  interface Vlan2
  nameif outside_mgts
  security-level 0
  62.112.100.R1 255.255.255.252 IP address
  !
  passive FTP mode
  clock timezone 3 MSK/MSD
  clock to DST MSK/MDD recurring last Sun Mar 02:00 last Sun Oct 03:00
  DNS lookup field inside
  DNS server-group MGTS
  Server name 195.34.31.50
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  network of the NET72 object
  10.1.72.0 subnet 255.255.255.0
  network object obj - 0.0.0.0
  host 0.0.0.0
  network of the Nafanya object
  Home 10.1.72.5
  network object obj - 10.1.72.0
  10.1.72.0 subnet 255.255.255.0
  network of the NET61 object
  10.1.61.0 subnet 255.255.255.0
  network of the NETWORK_OBJ_10.1.72.96_27 object
  subnet 10.1.72.96 255.255.255.224
  network of the NETT72 object
  10.1.72.0 subnet 255.255.255.0
  network of the NET30 object
  10.1.30.0 subnet 255.255.255.0
  network of the NETWORK_OBJ_10.1.72.0_24 object
  10.1.72.0 subnet 255.255.255.0
  object-group service OG INET
  the purpose of the echo icmp message service
  response to echo icmp service object
  service-object icmp traceroute
  service-object unreachable icmp
  service-purpose tcp - udp destination eq echo
  the DM_INLINE_NETWORK_1 object-group network
  network-object NET30
  network-object, object NET72
  DM_INLINE_TCP_1 tcp service object-group
  port-object eq www
  EQ object of the https port
  inside_access_in extended access list permit ip object NET72 object-group DM_INLINE_NETWORK_1
  access extensive list ip 10.1.72.0 inside_access_in allow 255.255.255.0 any
  inside_access_in extended access list permit ip object Nafanya any idle state
  inside_access_in list extended access allowed object-group OG INET an entire
  inside_access_in of access allowed any ip an extended list
  inside_access_in list extended access deny ip any alerts on any newspaper
  outside_mgts_access_in list extended access allowed object-group OG INET an entire
  outside_mgts_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group
  outside_mgts_access_in list extended access deny ip any alerts on any newspaper
  access extensive list ip 10.1.72.0 outside_mgts_cryptomap allow 255.255.255.0 object NET61
  VPN-ST_splitTunnelAcl permit 10.1.72.0 access list standard 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  outside_mgts MTU 1500
  IP check path reverse interface outside_mgts
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside outside_mgts) static source NET72 NET72 NETWORK_OBJ_10.1.72.96_27 NETWORK_OBJ_10.1.72.96_27 non-proxy-arp-search of route static destination
  NAT (inside outside_mgts) static source NETWORK_OBJ_10.1.72.0_24 NETWORK_OBJ_10.1.72.0_24 NET61 NET61 non-proxy-arp-search of route static destination
  !
  network obj_any object
  NAT (inside outside_mgts) dynamic obj - 0.0.0.0
  network of the NET72 object
  NAT (inside outside_mgts) interface dynamic dns
  inside_access_in access to the interface inside group
  Access-group outside_mgts_access_in in the outside_mgts interface
  Route 0.0.0.0 outside_mgts 0.0.0.0 62.112.100.R 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  without activating the user identity
  identity of the user by default-domain LOCAL
  AAA authentication http LOCAL console
  the ssh LOCAL console AAA authentication
  Enable http server
  http 10.1.72.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
  card crypto outside_mgts_map 1 match address outside_mgts_cryptomap
  card crypto outside_mgts_map 1 set pfs Group1
  peer set card crypto outside_mgts_map 1 91.188.180.42
  card crypto outside_mgts_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_mgts_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  card crypto outside_mgts_map interface outside_mgts
  inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  inside crypto map inside_map interface
  Crypto ca trustpoint ASDM_TrustPoint0
  registration auto
  E-mail [email protected] / * /
  name of the object CN = door-71
  Serial number
  IP address 62.112.100.42
  Proxy-loc-transmitter
  Configure CRL
  Crypto ca trustpoint ASDM_TrustPoint1
  registration auto
  ASDM_TrustPoint1 key pair
  Configure CRL
  trustpool crypto ca policy
  string encryption ca ASDM_TrustPoint0 certificates
  certificate eff26954
  30820395 3082027d a0030201 020204ef f2695430 0d06092a 864886f7 0d 010105
  019
  6460ae26 ec5f301d 0603551d 0e041604 14c9a3f2 d70e6789 38fa4b01 465d 1964
  60ae26ec 5f300d06 092 has 8648 01050500 03820101 00448753 7baa5c77 86f70d01
  62857b 65 d05dc91e 3edfabc6 7b3771af bbedee14 673ec67d 3d0c2de4 b7a7ac05
  5f203a8c 98ab52cf 076401e5 1a2c6cb9 3f7afcba 52c617a5 644ece10 d6e1fd7d
  28b57d8c aaf49023 2037527e 9fcfa218 9883191f 60b221bf a561f2be d6882091
  0222b7a3 3880d6ac 49328d1f 2e085b15 6d1c1141 5f850e5c b6cb3e67 0e373591
  94a 82781 44493217 and 38097952 d 003 5552 5c445f1f 92f04039 a23fba20 b9d51b13
  f511f311 d1feb2bb 6d056a15 7e63cc1b 1f134677 8124c 024 3af56b97 51af8253
  486844bc b1954abe 8acd7108 5e4212df db835d76 98ffdb2b 8c8ab915 193b 8167
  0db3dd54 c8346b96 c4f4eff7 1e7cd576 a8b1f86e 3b868a6e 89
  quit smoking
  string encryption ca ASDM_TrustPoint1 certificates
  certificate a39a2b54
  3082025f 30820377 a0030201 020204 has 3 9a2b5430 0d06092a 864886f7 0d 010105
  0500304 06035504 03130767 36313137 30120603 55040513 6174652d 3110300e b
     
  c084dcd9 d250e194 abcb3eb8 1da93bd0 fb0dba1a b1c35b43 d547a841 5d4ee1a4
  14bdb207 7dd790a4 0cd 70471 5f3a896a 07bd56dc ea01b3dd 254cde88 e1490e97
  f3e54c05 551adde0 66aa3782 c85880c2 b162ec29 4e49346a df71062d 6d6d8f49
  62b9de93 ba07b4f7 a50e77e1 8f54b32b 6627cb27 e982b36f a 362973, 0 88de3272
  9bd6d4d2 8ca1e11f 214f20a9 78bdea95 78fdc45c d6d45674 6acb9bcb d0bd930e
  638eedfe cd559ab1 e1205c48 3ee9616f e631db55 e82b623c 434ffdc1 11020301
  0001 has 363 3061300f 0603551d 130101ff 0101ff30 04053003 0e060355 1d0f0101
  ff040403 1f060355 02018630 230418 30168014 0cea70bf 0d0e0c4b eb34a0b1 1 d
  8242 has 549 0603 551d0e04 1604140c ea70bf0d 0e0c4beb 34a0b182 301D 5183ccf9
  42a 54951 010105 05000382 0101004e 7bfe054a 0d 864886f7 0d06092a 83ccf930
  d434a27c 1d3dce15 529bdc5f 70a2dff1 98975de9 2a97333b 96077966 05a8e9ef
  bf320cbd ecec3819 ade20a86 9aeb5bde bd129c7b 29341e4b edf91473 f2bf235d
  9aaeae21 a629ccc6 3c79200b b9a89b08 bf38afb6 ea56b957 4430f692 a 4745, 411
  34d71fad 588e4e18 2b2d97af b2aae6b9 b6a22350 d031615b 49ea9b9f 2fdd82e6
  ebd4dccd df93c17e deceb796 f268abf1 881409b 5 89183841 f484f0e7 bd5f7b69
  ebf7481c faf69d3e 9d24df6e 9c2b0791 785019f7 a0d20e95 2ef35799 66ffc819
  4a77cdf2 c6fb4380 fe94c13c d4261655 7bf3d6ba 6289dc8b f9aad4e1 bd918fb7
  32916fe1 477666ab c2a3d591 a84dd435 51711f6e 93e2bd84 89884c
  quit smoking
  crypto isakmp identity address
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev2 activate outside_mgts port 443 customer service
  Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
  Crypto ikev1 allow inside
  Crypto ikev1 enable outside_mgts
  IKEv1 crypto policy 10
  authentication crack
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 20
  authentication rsa - sig
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 40
  authentication crack
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 50
  authentication rsa - sig
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 60
  preshared authentication
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 70
  authentication crack
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 80
  authentication rsa - sig
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 90
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 100
  authentication crack
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 110
  authentication rsa - sig
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 120
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 130
  authentication crack
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 140
  authentication rsa - sig
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 150
  preshared authentication
  the Encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  without ssh stricthostkeycheck
  SSH 10.1.72.0 255.255.255.0 inside
  SSH timeout 60
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  vpnclient Server 91.188.180.X
  vpnclient mode network-extension-mode
  vpnclient nem-st-autoconnect
  VPN - L2L vpnclient vpngroup password *.
  vpnclient username aradetskayaL password *.
  dhcpd auto_config outside_mgts
  !
  dhcpd update dns replace all two interface inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  SSL-trust ASDM_TrustPoint0 inside point
  SSL-trust ASDM_TrustPoint0 outside_mgts point
  WebVPN
  Select outside_mgts
  internal GroupPolicy_91.188.180.X group strategy
  attributes of Group Policy GroupPolicy_91.188.180.X
  Ikev1 VPN-tunnel-Protocol
  internal group VPN - ST strategy
  attributes of group VPN - ST policy
  value of 195.34.31.50 DNS Server 8.8.8.8
  Ikev1 VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value VPN-ST_splitTunnelAcl
  by default no
  aradetskayaL encrypted HR3qeva85hzXT6KK privilege 15 password username
  tunnel-group 91.188.180.X type ipsec-l2l
  attributes global-tunnel-group 91.188.180.X
  Group - default policy - GroupPolicy_91.188.180.42
  IPSec-attributes tunnel-group 91.188.180.X
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.
  remotely IKEv2 authentication certificate
  pre-shared-key authentication local IKEv2 *.
  remote access to tunnel-group VPN - ST type
  VPN-general ST-attributes tunnel-group
  address vpnpool pool
  Group Policy - by default-VPN-ST
  tunnel-group ipsec VPN ST-attributes
  IKEv1 pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  inspect the icmp error
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:212e4f5035793d1c219fed57751983d8
  : end

  door-71 # sh crypto ikev1 his

  There are no SAs IKEv1

  door-71 # sh crypto ikev2 his

  There are no SAs IKEv2

  door-71 # sh crypto ipsec his

  
  There is no ipsec security associations
  door-71 # sh crypto isakmp

  There are no SAs IKEv1

  There are no SAs IKEv2

  Global statistics IKEv1
  The active Tunnels: 0
  Previous Tunnels: 0
  In bytes: 0
  In the packages: 0
  In packs of fall: 0
  In Notifys: 0
  In the constituencies of P2: 0
  In P2 invalid Exchange: 0
  In P2 Exchange rejects: 0
  Requests for removal in his P2: 0
  Bytes: 0
  Package: 0
  Fall packages: 0
  NOTIFYs out: 0

  
  Exchanges of P2: 0
  The Invalides Exchange P2: 0
  Exchange of P2 rejects: 0
  Requests to remove on P2 Sa: 0
  Tunnels of the initiator: 0
  Initiator fails: 0
  Answering machine fails: 0
  Ability system breaks down: 0
  AUTH failed: 0
  Decrypt failed: 0
  Valid hash fails: 0
  No failure his: 0

  IKEV1 statistics for Admission appeals
  In negotiating SAs Max: 25
  In negotiating SAs: 0
  In negotiating SAs Highwater: 0
  In negotiating SAs rejected: 0

  Global statistics IKEv2
  The active Tunnels: 0
  Previous Tunnels: 0
  In bytes: 0
  In the packages: 0
  In packs of fall: 0
  In Fragments of fall: 0
  In Notifys: 0
  In Exchange for the P2: 0
  In P2 invalid Exchange: 0
  In P2 Exchange rejects: 0
  In IPSEC delete: 0
  In delete IKE: 0
  Bytes: 0
  Package: 0
  Fall packages: 0
  Fragments of fall: 0
  NOTIFYs out: 0
  Exchange of P2: 0
  The Invalides Exchange P2: 0
  Exchange of P2 rejects: 0
  On IPSEC delete: 0
  The IKE Delete: 0
  Locally launched sAs: 0
  Locally launched sAs failed: 0
  SAs remotely initiated: 0
  SAs remotely initiated failed: 0
  System capacity: 0
  Authentication failures: 0
  Decrypt failures: 0
  Hash failures: 0
  Invalid SPI: 0
  In the Configs: 0
  Configs: 0
  In the Configs rejects: 0
  Configs rejects: 0
  Previous Tunnels: 0
  Previous Tunnels wraps: 0
  In the DPD Messages: 0
  The DPD Messages: 0
  The NAT KeepAlive: 0
  IKE recomposition launched locally: 0
  IKE returned to the remote initiated key: 0
  Generate a new key CHILD initiated locally: 0
  CHILD given to the remote initiated key: 0

  IKEV2 statistics for Admission appeals
  Max active SAs: no limit
  Max in negotiating SAs: 50
  Challenge cookie line: never
  Active sAs: 0
  In negotiating SAs: 0
  Incoming requests: 0
  Accepted incoming requests: 0
  A rejected incoming requests: 0
  Out of requests: 0
  Out of the applications accepted: 0
  The outgoing rejected requests: 0
  A rejected queries: 0
  Rejected at the SA: 0 Max limit
  Rejected low resources: 0
  Rejected the current reboot: 0
  Challenges of cookie: 0
  Cookies transmitted challenges: 0
  Challenges of cookie failed: 0

  IKEv1 global IPSec over TCP statistics
  --------------------------------
  Embryonic connections: 0
  Active connections: 0
  Previous connections: 0
  Incoming packets: 0
  Inbound packets ignored: 0
  Outgoing packets: 0
  Outbound packets ignored: 0
  The RST packets: 0
  Heartbeat Recevied ACK packets: 0
  Bad headers: 0
  Bad trailers: 0
  Chess timer: 0
  Checksum errors: 0
  Internal error: 0

   
  door-71 # sh statistical protocol all cryptographic
  [Statistics IKEv1]
  Encrypt packets of requests: 0
  Encapsulate packets of requests: 0
  Decrypt packets of requests: 0
  Decapsulating requests for package: 0
  HMAC calculation queries: 0
  ITS creation queries: 0
  SA asked to generate a new key: 0
  Deletion requests: 0
  Next phase of allocation key applications: 0
  Number of random generation queries: 0
  Failed requests: 0
  [Statistics IKEv2]
  Encrypt packets of requests: 0
  Encapsulate packets of requests: 0
  Decrypt packets of requests: 0
  Decapsulating requests for package: 0
  HMAC calculation queries: 0
  ITS creation queries: 0
  SA asked to generate a new key: 0
  Deletion requests: 0
  Next phase of allocation key applications: 0
  Number of random generation queries: 0
  Failed requests: 0
  [IPsec statistics]
  Encrypt packets of requests: 0
  Encapsulate packets of requests: 0
  Decrypt packets of requests: 0
  Decapsulating requests for package: 0
  HMAC calculation queries: 0
  
  ITS creation queries: 0
  SA asked to generate a new key: 0
  Deletion requests: 0
  Next phase of allocation key applications: 0
  Number of random generation queries: 0
  Failed requests: 0
  [SSL statistics]
  Encrypt packets of queries: 19331
  Encapsulate packets of queries: 19331
  Decrypt packets of queries: 437
  Package requests decapsulating: 437
  HMAC calculation queries: 19768
  ITS creation queries: 178
  SA asked to generate a new key: 0
  Requests to remove SA: 176
  Next phase of allocation key applications: 0
  Number of random generation queries: 0
  Failed requests: 0
  [Statistical SSH are not taken in charge]
  [Statistics SRTP]
  Encrypt packets of requests: 0
  Encapsulate packets of requests: 0
  Decrypt packets of requests: 0
  Decapsulating requests for package: 0
  HMAC calculation queries: 0
  ITS creation queries: 0
  SA asked to generate a new key: 0
  Deletion requests: 0
  Next phase of allocation key applications: 0
  Number of random generation queries: 0
  Failed requests: 0
  [Statistics]
  Encrypt packets of requests: 0
  Encapsulate packets of requests: 0
  Decrypt packets of requests: 0
  Decapsulating requests for package: 0
  HMAC calculation queries: 6238
  ITS creation queries: 0
  SA asked to generate a new key: 0
  Deletion requests: 0
  Next phase of allocation key applications: 0
  Number of queries random generation: 76
  Failure of queries: 9

  door-71 # sh crypto ca trustpoints

  Trustpoint ASDM_TrustPoint0:
  Configured for the production of a self-signed certificate.

  Trustpoint ASDM_TrustPoint1:
  Configured for the production of a self-signed certificate.

  If you need something more, then spread!
  Please explain why it is that I don't want to work?

  Hello

  When the IPSEC tunnel does not come to the top, the first thing comes to my mind is to run a tracer of package from the CLI and the phases in it. Please run this command from your firewall side and share the output. I've just compiled this command with the random ip address and ports of your given range.

  Packet-trace entry inside tcp 10.1.72.2 1233 10.1.61.2 443 detailed

  Best regards

  Amandine

• ASA 5505 - several VPN subnet

  I'm trying to set up a VPN for use with the Cisco VPN Client.  I currently have operational VPN, but I cannot allow access to several subnets connected to the ASA.  My current stock of VPN DHCP is 10.0.0.0/24.  I want to VPN users to talk to one of my other VLAN (172.16.20.0/24).  That's what I can't understand.  If I change my VPN DHCP pool to something like 172.16.20.100 - 110 can I talk to about everything on this fine subnet.  But as soon as I change the DHCP pool to the other subnet so I can't.  Any suggestions?

  Here is my config:

  Nysyr-SBO-ASA (config) # sh run

  : Saved

  :

  ASA Version 8.4 (1)

  !

  names of

  !

  interface Vlan1

  No nameif

  no level of security

  no ip address

  !

  interface Vlan2

  Description connection to the ISP (FiOS)

  nameif primaryisp

  security-level 0

  IP address

  !

  interface Vlan3

  Description secondary connection ISP (Time Warner)

  nameif backupisp

  security-level 0

  IP address

  !

  interface Vlan5

  Description Connection to the subnet internal internet access (192.168.5.0/24)

  nameif inside

  security-level 100

  192.168.5.1 IP address 255.255.255.0

  !

  interface Vlan20

  Description Connection to the internal management network (172.16.20.0/24)

  nameif insidemgmt

  security-level 100

  address 172.16.20.1 IP 255.255.255.0

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  switchport access vlan 3

  !

  interface Ethernet0/2

  switchport access vlan 5

  !

  interface Ethernet0/3

  switchport access vlan 20

  !

  interface Ethernet0/4

  Shutdown

  !

  interface Ethernet0/5

  Shutdown

  !

  interface Ethernet0/6

  Shutdown

  !

  interface Ethernet0/7

  Shutdown

  !

  passive FTP mode

  clock timezone IS - 5

  clock to summer time EDT recurring

  internal network object

  192.168.5.0 subnet 255.255.255.0

  network of the object asp-wss-1-tw

  Home 192.168.5.11

  network of the object asp-wss-1-vz

  Home 192.168.5.11

  network vpn-ip-pool of objects

  10.0.0.0 subnet 255.255.255.0

  access-list outside_access_in_1 note access list to allow outside in traffic

  outside_access_in_1 list extended access permit tcp any object asp-wss-1-vz eq www

  outside_access_in_1 list extended access permit tcp any object asp-wss-1-vz eq https

  outside_access_in_1 list extended access permit tcp any object asp-wss-1-tw eq www

  outside_access_in_1 list extended access permit tcp any object asp-wss-1-tw eq https

  SBOnet_VPN_Tunnel_splitTunnelAcl standard access list allow 172.16.20.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  primaryisp MTU 1500

  backupisp MTU 1500

  Within 1500 MTU

  insidemgmt MTU 1500

  vpn-ip-pool 10.0.0.10 mask - 255.255.255.0 IP local pool 10.0.0.250

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside primaryisp) source Dynamics one interface

  NAT (inside backupisp) source Dynamics one interface

  !

  network of the object asp-wss-1-tw

  NAT (inside backupisp) static

  network of the object asp-wss-1-vz

  NAT (inside primaryisp) static

  Access-group outside_access_in_1 in the primaryisp interface

  Access-group outside_access_in_1 in the backupisp interface

  Route 0.0.0.0 primaryisp 0.0.0.0 1 track 1

  Route 0.0.0.0 backupisp 0.0.0.0 10

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.5.0 255.255.255.0 inside

  http 0.0.0.0 0.0.0.0 primaryisp

  http 0.0.0.0 0.0.0.0 backupisp

  http 0.0.0.0 0.0.0.0 insidemgmt

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  monitor SLA 123

  type echo protocol ipIcmpEcho 8.8.8.8 interface primaryisp

  threshold of 3000

  frequency 10

  Annex ALS life monitor 123 to always start-time now

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-256-SHA ikev1

  primaryisp_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  card crypto primaryisp_map interface primaryisp

  backupisp_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  card crypto backupisp_map interface backupisp

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN =

  Configure CRL

  IKEv2 crypto policy 1

  aes-256 encryption

  integrity sha

  Group 5

  FRP sha

  second life 86400

  Crypto ikev2 enable primaryisp

  Crypto ikev2 enable backupisp

  Crypto ikev1 enable primaryisp

  Crypto ikev1 enable backupisp

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  !

  track 1 rtr 123 accessibility

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 primaryisp

  SSH 0.0.0.0 0.0.0.0 backupisp

  SSH 0.0.0.0 0.0.0.0 insidemgmt

  SSH timeout 20

  Console timeout 20

  No vpn-addr-assign aaa

  No dhcp vpn-addr-assign

  a basic threat threat detection

  statistical threat detection port

  Statistical threat detection Protocol

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal SBOnet_VPN_Tunnel group strategy

  attributes of Group Policy SBOnet_VPN_Tunnel

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  value of Split-tunnel-network-list SBOnet_VPN_Tunnel_splitTunnelAcl

  attributes of Group Policy DfltGrpPolicy

  value of Split-tunnel-network-list SBOnet_VPN_Tunnel_splitTunnelAcl

  attributes global-tunnel-group DefaultRAGroup

  VPN-ip-pool-pool of addresses (primaryisp)

  ip vpn-pool address pool

  IPSec-attributes tunnel-group DefaultRAGroup

  IKEv1 pre-shared-key *.

  type tunnel-group SBOnet_VPN_Tunnel remote access

  attributes global-tunnel-group SBOnet_VPN_Tunnel

  ip vpn-pool address pool

  Group Policy - by default-SBOnet_VPN_Tunnel

  IPSec-attributes tunnel-group SBOnet_VPN_Tunnel

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:7a817a8679e586dc829c06582c60811d

  : end

  keep deleted thos lines, you don't need these lines to your remote access VPN.

  Please tell me, what is the default gateway assigned on these hosts sitting on the mgmt network segment?

• VPN connection problem

  Hello

  We have a server to remote client, on which we need to connect via VPN. My VPN is able to connect. But any application that needs to connect via VPN does not work. I also can't ping on remote servers. While for others its works very well. I can't understand the problem, I tried to reinstall the VPN client.

  I am using windows XP pro and the client VPN CISCO 4.0.3.

  Hello

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the forum TechNet for assistance:

  TechNet Windows XP Service Pack 3 (SP3)

  Hope the helps of information.

• Client VPN connectivity problems

  I use the cisco VPN client to connect to our network, located behind a 515E. The client is authenticated and gets an ip address but cannot ping or connect with one of the hosts. The connection is to a network of customers that is also behind a 515E. I have successfully connected using the same policy to other places and have had no problem. What confuses me, is that we have used to have a Netscreen firewall before and he had a netscreen vpn client which connected since their network with a problem. Is that something they need for their firewall so that we can get through the traffic?

  Try to turn on NAT - T on your pix, by setting up:

  ISAKMP nat-traversal 20

  and configure the client vpn accordingly:

  http://www.Cisco.com/warp/public/471/cvpn_3k_nat.html#conf_client

  I think these discussions are useful:

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=virtual%20Private%20Networks&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1dd7dda4

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=virtual%20Private%20Networks&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1dd7fe80