Cisco ASA 5505 remote VPN access to the local network

Similar Questions

• ASA5505 can transfer clients to remote VPN access to the local network

  I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.

  Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?

  These two cases are possible? :

  (1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
  (2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
  Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
  Thank you.

  I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.

  You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.

• ASA 5505 VPN remote cannot access with my local network

  Hello guys, I have a problem with my asa 5505 remote VPN access to the local network, the VPn connection works well and connected, but the problem is that I can't reach my inside connection network of 192.168.30.x, here's my setup, please can you help me

  ASA Version 8.2 (1)

  !

  !

  interface Vlan1

  nameif inside

  security-level 100

  192.168.30.1 IP address 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 155.155.155.10 255.255.255.0

  !

  interface Vlan5

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  inside_nat0_outbound list of allowed ip extended access any 192.168.100.0 255.255.255.240

  pager lines 24

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool vpn-pool 192.168.100.1 - 192.168.100.10 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  Mull strategy of Group internal

  attributes of the Group mull strategy

  Protocol-tunnel-VPN IPSec

  username privilege 0 encrypted password eKJj9owsQwAIk6Cw xxx

  VPN-group-policy Mull

  type mull tunnel-group remote access

  tunnel-group mull General attributes

  address vpn-pool pool

  Group Policy - by default-mull

  Mull group tunnel ipsec-attributes

  pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  !

  global service-policy global_policy

  context of prompt hostname

  Yes, you will need to either configure split tunnel so that internet traffic goes out through your local Internet service provider, GOLD / directed by configuration current you are tunneling all traffic (internet traffic Inc.) to the ASA, then you will need to create NAT for internet traffic.

  To set up a tunnel from split:

  split-acl access-list allowed 192.168.30.0 255.255.255.0

  attributes of the Group mull strategy

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split-acl

  I hope this helps.

• Cisco ASA 5505 unable to access the remote network

  Hello

  I have a Cisco ASA 5505, with 50 basic license, which is connected directly to the Modem cable with a public IP address. I have configured and active VPN on the outside interface. When connect us, we connect well without error, but we are not able to access all the resources on the remote network.

  ASA IOS version 8.2 (5)

  Remote IP network: 10.0.0.0/24

  VPN IP Pool: 192.168.102.10 - 25

  I have attached the config: llc.txt

  Please let me know if you have any questions.

  Thank you!

  Hello

  Try adding NAT 0 because inside subnet--> subnet distance

  NAT (inside) 0 access-list TEST

  TEST access ip 10.0.0.0 scope list allow 255.255.255.0 192.168.102.10 255.255.255.224

  HTH

  MS

• Client remote access VPN gets connected without access to the local network

  : Saved

  :

  ASA 1.0000 Version 2

  !

  hostname COL-ASA-01

  domain dr.test.net

  turn on i/RAo1iZPOnp/BK7 encrypted password

  i/RAo1iZPOnp/BK7 encrypted passwd

  names of

  !

  interface GigabitEthernet0/0

  nameif outside

  security-level 0

  IP 172.32.0.11 255.255.255.0

  !

  interface GigabitEthernet0/1

  nameif inside

  security-level 100

  IP 192.9.200.126 255.255.255.0

  !

  interface GigabitEthernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/5

  nameif failover

  security-level 0

  192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2

  !

  interface Management0/0

  nameif management

  security-level 0

  192.168.2.11 IP address 255.255.255.0

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain dr.test.net

  network of the RAVPN object

  192.168.0.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.168.200.0_24 object

  192.168.200.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.9.200.0_24 object

  192.9.200.0 subnet 255.255.255.0

  the inside_network object-group network

  object-network 192.9.200.0 255.255.255.0

  external network object-group

  host of the object-Network 172.32.0.25

  Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0

  access-list extended test123 permit ip host 192.168.200.1 192.9.200.190

  access-list extended test123 permit ip host 192.9.200.190 192.168.200.1

  access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0

  192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24

  pager lines 24

  management of MTU 1500

  Outside 1500 MTU

  Within 1500 MTU

  failover of MTU 1500

  local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 66114.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) source Dynamics one interface

  NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24

  Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  Enable http server

  http 0.0.0.0 0.0.0.0 outdoors

  http 0.0.0.0 0.0.0.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI

  Configure CRL

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet 192.9.200.0 255.255.255.0 inside

  Telnet timeout 30

  SSH 0.0.0.0 0.0.0.0 management

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 66.35.45.128 255.255.255.192 outside

  SSH 0.0.0.0 0.0.0.0 inside

  SSH timeout 30

  SSH version 2

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  internal RAVPN group policy

  RAVPN group policy attributes

  value of server WINS 192.9.200.164

  value of 66.35.46.84 DNS server 66.35.47.12

  VPN-filter value test123

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value test123

  Dr.kligerweiss.NET value by default-field

  username test encrypted password xxxxxxx

  username admin password encrypted aaaaaaaaaaaa privilege 15

  vpntest Delahaye of encrypted password username

  type tunnel-group RAVPN remote access

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  Group Policy - by default-RAVPN

  IPSec-attributes tunnel-group RAVPN

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory 2

  Subscribe to alert-group configuration periodic monthly 2

  daily periodic subscribe to alert-group telemetry

  aes encryption password

  Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea

  : end

  COL-ASA-01 #.

  Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface

  Test of Cape COLLAR-ASA-01 # sho | in 192.168.200

  25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request

  29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68

  38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68

  56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68

  69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request

  98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request

  99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68

  108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68

  115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68

  116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request

  COL-ASA-01 #.

  Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.

  And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...

  Hello

  The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.

  You can try the following changes

  attributes global-tunnel-group RAVPN

  No address RAVPN pool

  no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool

  local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask

  attributes global-tunnel-group RAVPN

  address RAVPN pool

  no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24

  In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.

  the object of the LAN network

  192.168.200.0 subnet 255.255.255.0

  network of the VPN-POOL object

  192.168.201.0 subnet 255.255.255.0

  NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL

  NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.

  You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.

  No source (indoor, outdoor) nat Dynamics one interface

  NAT source auto after (indoor, outdoor) dynamic one interface

  NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections

  Hope this helps

  Let me know if it works for you

  -Jouni

• Ipad Cisco ipsec VPN connects but not access to the local network

  Hi guys,.

  I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.

  If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.

  Cisco 877.

  My config is attached.

  Any ideas?

  Thank you

  Build-in iPad-client is not useful to your configuration.

  You have three options:

  (1) remove the ACL of your vpn group. Without split tunneling client will work.

  2) migrate legacy config crypto-map style. Here, you can use split tunneling

  3) migrate AnyConnect.

  The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.

• Cisco ASA 5505 - Configuration VPN

  I'm trying to configure a VPN connection to allow customers access to the internal network. I have tried to use time Wizard VPN & repeatedly but customer connect but can get out to the internet and communicate with any host on the network. I tried to use a vpn in the 192.x.x.x or 10.10.1.X network dhcp pool but no luck.

  Comments or suggestions appreciated.

  What is the reason for these commands?

  NAT (outside) 0-list of access policyPAT

  NAT (outside) 5 10.10.1.0 255.255.255.0

  If this isn't spicific reason remove

  and put the following command:

  Permitted connection ipsec sysopt

  in global configuration mode to enable the VPN traffic to work around interface access lists

  Good luck

  If useful rates

• VPN access to several local networks virtual asa8.3

  you are looking for assistance. This one goes batty.

  I have ASA 5510 8.3 running

  It serves as a router, firewall and vpn.

  the underlying network works fine.

  When I connect via VPN, I can only access my reseau.41 and not on the reseau.42. When I try to do a ping.42 I get this error:

  5 October 18, 2010 00:33:13 192.168.42.11 3389 rules asymmetrical NAT matched for flows forward and backward; Connection for tcp src Outside:192.168.43.200/2916 dst servers:192.168.42.11/3389 refused due to path failure reverse that of NAT

  If I flip through these rules in order to config then I can acceder.42 through the vpn but pas.41

  NAT (servers, all) static source any any destination static obj-vpnpool obj-vpnpool
  NAT (iscsimgmt, any) static source any any destination static obj-vpnpool obj-vpnpool

  I'm confused because it's all a new config and I used the wizard in asdm and couldn't access squat (perhaps he does not know how to manage the VLAN)?

  the ASA may well ping of all networks.

  devices on the network can ping each other fine

  just via ipsec vpn, I can't access both networks.

  thoughts?

  Please configure a more specific NAT statements as follows:

  object obj-iscsimgmt network
  192.168.42.0 subnet 255.255.255.0
  

  
  

  NAT (servers, Outside) source static obj-servers obj-servers destination static obj-vpnpool obj-vpnpool
  NAT (iscsimgmt, Outside) source static obj-iscsimgmt obj-iscsimgmt destination static obj-vpnpool obj-vpnpool

  And pls Remove the following:

  NAT (servers, all) static source any any destination static obj-vpnpool obj-vpnpool
  NAT (iscsimgmt, any) static source any any destination static obj-vpnpool obj-vpnpool

  Then "clear xlate" after the changes described above.

  Hope that helps.

• PORT of Configuration.DEFAULT of ASA AnyConnect remote VPN access.

  Hello!!! Now, I need to configure the AnyConnect VPN remote access. And I have a question.

  The default 443 AnyConnect port, but the port is occupied on SAA. We use this port for another application.

  How to change the port to connect? Is this true? Thank you!!!

  Hi, please add the following configuration:

  1. Enable the WebVPN on the SAA feature:

     ASA(config)#webvpn

  2. Enable WebVPN services for the external interface of the ASA:

     ASA(config-webvpn)#enable outside

  3. Allow the ASA to listen WebVPN traffic on the custom port number:

     ASA(config-webvpn)#port <1-65535>

• Remote VPN with PIX without access to the local network

  Hi @all,

  I ve running into problems and I have not found any solution. Can someone check my config?

  Facts:

  PIX 501 6.3 (3)

  4.04 VPN client

  Wanted solution: access to HO via VPN

  VPN tunnel will be established, I get an IP address, but I can´t the systems behind the pix and the pix of access itself.

  To the VPN Client Staticts, I see outgoing packets, but no entrant (if I send a ping to peer behind the pix)

  I hope someone can help me

  Attached is my config:

  PIX 501 and 506/506e pix are not supported in v7 due to the fact that the cpu is not able to deal with the extended features of v7.

  PIX 520 is not supported I guess it's because of the fact that the model is discontinued.

• Cisco router access outside the local network interface

  Hi all!

  I have Cisco router 892 (c890-universalk9 - mz.154 - 3.M4.bin) with firewall area and based on routing strategies.

  Everything works fine, but now I need to have the ability to access external router interface IP LAN addresses.

  For example, I PAT 192.168.4.1 port 8443 to the outside interface IP (93.93.93.2 for example) and I need to check LAN 93.93.93.2:8443.

  ! PAT:

  IP nat inside source static tcp 192.168.4.1 8443 93.93.93.1 - extensible 8443 SDM_RMAP_1 road map

  ! DynNat to the internet:

  IP nat inside source overload map route SDM_RMAP_1 interface GigabitEthernet0

  ! Routing policy

  SDM_RMAP_1 allowed 10 route map
  corresponds to the IP 101
  match interface GigabitEthernet0

  ! ACL 101 for routing policy

  access-list 101 deny ip 192.168.3.0 0.0.0.255 192.168.111.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.192.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.177.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.61.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.17.19.0 0.0.0.255
  access-list 101 deny ip 192.168.4.0 0.0.0.255 192.168.111.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 host 172.16.194.100
  access-list 101 deny ip 192.168.3.0 0.0.0.255 10.0.0.0 0.255.255.255
  access-list 101 deny ip 192.168.4.0 0.0.0.255 10.0.0.0 0.255.255.255
  access-list 101 deny ip 192.168.4.0 0.0.0.255 host 172.31.255.1
  access-list 101 deny ip 192.168.4.0 0.0.0.255 host 172.16.194.100
  access-list 101 permit ip 192.168.3.0 0.0.0.255 any
  access-list 101 permit ip 192.168.4.0 0.0.0.255 any

  ! ACL on the external interface:

  plug-in software component gi0 extended IP access list
  allow an ip
  allow icmp a whole

  ! External interface

  interface GigabitEthernet0
  Description $ETH - WAN$
  IP 93.93.93.1 255.255.255.240
  IP access-group gi0-in in
  NAT outside IP
  IP virtual-reassembly in
  EXTENT of the Member's area network security
  IP tcp adjust-mss 1452
  automatic duplex
  automatic speed
  card crypto SDM_CMAP_2

  ! Inside DMZ interface vlan:

  interface Vlan4
  IP 192.168.4.254 255.255.255.0
  IP nat inside
  IP virtual-reassembly in
  security of the members of the DMZ
  IP tcp adjust-mss 1452

  ! Allow outbound traffic to DMZ to Internet:

  Allow_All_ACL-DMZ extended IP access list
  allow an esp
  permit tcp host 192.168.4.1 host 192.168.111.2 eq 1521
  refuse the 192.168.4.0 ip 0.0.0.255 192.168.111.0 0.0.0.255
  refuse the 192.168.4.0 ip 0.0.0.255 172.17.19.0 0.0.0.255
  allow icmp 192.168.4.0 0.0.0.255 any
  ip licensing 192.168.4.0 0.0.0.255 any

  ! Allow incoming traffic from the Internet to DMZ:

  WAN_DMZ_ACL extended IP access list
  allow tcp any a Workbench
  permit tcp any any eq ftp
  permit tcp any any eq 990
  permit tcp everything any 51000 53000 Beach
  permit tcp any any eq 995
  permit tcp any any eq 465
  permit tcp any any eq www
  permit any any eq 443 tcp
  allow icmp a whole
  allow an esp
  permit any any eq non500-isakmp udp
  host ip 212.98.162.139 permit 192.168.4.0 0.0.0.255
  IP 81.30.80.0 allow 0.0.0.255 any
  IP 192.168.111.0 allow 0.0.0.255 192.168.4.0 0.0.0.255
  IP 172.17.19.0 allow 0.0.0.255 192.168.4.0 0.0.0.255
  host ip 172.16.194.100 permit 192.168.4.0 0.0.0.255
  host ip 172.31.255.1 permit 192.168.4.0 0.0.0.255
  permit ip host 172.31.255.1 172.17.193.100
  refuse an entire ip

  ! Focus on the area of firewall:

  type of class-card inspect entire game DMZ_WAN_CLASS
  match the group-access name DMZ Allow_All_ACL

  type of class-card inspect entire game WAN_DMZ_CLASS
  match the name of group-access WAN_DMZ_ACL

  type of policy-card inspect DMZ_WAN_POLICY
  class type inspect DMZ_WAN_CLASS
  inspect
  class class by default
  drop

  type of policy-card inspect WAN_DMZ_POLICY
  class type inspect WAN_DMZ_CLASS
  inspect
  class class by default
  drop

  the DMZ security

  
  area WAN security

  Security WAN_DMZ of the pair area source destination WAN DMZ
  type of service-strategy inspect WAN_DMZ_POLICY
  destination of DMZ_WAN source DMZ area pair WAN security
  type of service-strategy inspect DMZ_WAN_POLICY

  Maybe someone can help me to make Cisco to allow ports outside LAN using a NAT?

  I did this on Mikrotik easily = |

  It is due to the fact that they do not allow "hair pinning" by default, once this is configured, it will work.

  Martin

• ASA 5505 - order Internet access for users

  Hi all

  I have a Cisco ASA 5505 connect my LAN over the internet using NAT/PAT. I want to restrict access to the internet on ports 80 and 443 on a per user basis.

  That is to say access to management staff while limiting the general staff.

  I understand how this on a per device level by creating an access list to block certain IP addresses to the internet, but I would limit some users.

  I guess they will have to authenticate to the ASA some how.

  Pointers?

  TIA.

  You need to set up the Cup via proxy in ASA.

  Here is the configuration that we add on ASA:-

  access-list WEBAUTH permit tcp any any eq 80

  access-list WEBAUTH permit tcp any any eq 443

  AAA authentication WEBAUTH indoor soccer match

  AAA authentication secure-http-client

  AAA authentication listener http inside port www redirect

  Redirect the AAA authentication listener https within the https port

  http://www.Cisco.com/en/us/docs/security/ASA/asa72/configuration/guide/fwaaa.html#wp1043431

  http://www.Cisco.com/en/us/docs/security/ASA/asa72/command/reference/a1_72.html#wp1437427

  Kind regards

  ~ JG

  Note the useful messages

• Cisco Asa 5505 and level 3 with remote access VPN switch

  Today I had a new CISCO LAYER 3 switch... So here's my scenrio

  Cisco Asa 5505

  I have

  Outside of the == 155.155.155.x

  Inside = 192.168.7.1

  Address POOL VPN = 10.10.10.1 - 10.10.10.20

  3 layer switch configuration

  VLAN 2

  ip address of the interface = 192.168.1.1

  VLAN 2

  ip address of the interface = 192.168.2.1

  VLAN 2

  ip address of 192.168.3.1 = interface

  VLAN 2

  ip address of the interface = 192.168.4.1

  VLAN 2

  ip address of the interface = 192.168.5.1

  IP Routing

  So I want the customers of my remote access VPN to access all that these networks. So please can you give me a useful tip or a link to set up the rest of my trip

  Thanks to you all

  Al ready has responded

  Sent by Cisco Support technique iPad App

• Cisco ASA, connect an IP address on the OUTSIDE of the VPN remote access

  Hello

  I tried to find resources on the net but could not find a solution, then post it here. Maybe someone can help.

  So the problem is that I'm trying to access a server on the cloud for remote VPN access (cisco asa 5510).

  The server on the cloud (54.54.54.54) is only accessible from the outside interface (192.168.11.2) NY Firewall (cisco asa 5510)

  I added some ACE for this in the ACL of VPN tunnel to divide.

  NY-standard host allowed fw # access - list vpn_remote-customer 54.54.54.54

  And I see the road added to my cliet machine after the VPN connection, but still it cannot connect to this server.

  The network INTERIOR, I can connect to the server.

  

  Thanks in advance.

  Hello

  This is most likely a problem with NAT hair/U-turn hairpin.

  Will need to see the configurations or you would need to check yourself

  I don't know what your version of the Software ASA is to be like who determines what is the format of NAT configuration.

  So far, you have confirmed that the ASA VPN configuration provides the VPN Client with the route to the remote server. Then in circulation should be tunnel to the ASA.

  Then, you will need to check the output of this command

  See the race same-security-traffic

  You should see the command in the output below

  permit same-security-traffic intra-interface

  If you do not, you will need to add it. This effect of controls is to allow traffic to enter an interface and exit through the same interface. In your case this applies to Internet VPN Client traffic to the remote server as it between ' outside ' and spell through the 'outside'.

  Then, should ensure that dynamic PAT is configured for the VPN Clients.

  8.2 software (and below)

  You most likely have a dynamic configuration PAT like that on the firewall, if levels of above running software version

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0

  In this situation if we wanted to add dynamic PAT for a pool of VPN, we would add

  NAT (outside) 1

  This would allow users to use the same public IP address as LAN users, when accessing the remote VPN server

  Software 8.3 (and above)

  Because the NAT configuration format is completely different in the latest software, you could probably just add a new configuration of NAT completely without adding a

  network of the VPN-PAT object

  subnet

  dynamic NAT interface (outdoors, outdoor)

  Of course, its possible that there could be some configuration NAT already on the device which could cause problems for this configuration. If this does not work then that we would have to look at the actual configurations on the ASA.

  Hope this helps

  Let me know how it goes

  -Jouni

• ASA 5505 IPSEC VPN connected but cannot access the local network

  ASA: 8.2.5

  ASDM: 6.4.5

  LAN: 10.1.0.0/22

  Pool VPN: 172.16.10.0/24

  Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

  I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

  Here is my setup, wrong set up anything?

  ASA Version 8.2 (5)

  !

  hostname asatest

  domain XXX.com

  activate 8Fw1QFqthX2n4uD3 encrypted password

  g9NiG6oUPjkYrHNt encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.1.1.253 255.255.252.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  address IP XXX.XXX.XXX.XXX 255.255.255.240

  !

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  DNS server-group DefaultDNS

  domain vff.com

  vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

  access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

  pager lines 24

  Enable logging

  timestamp of the record

  logging trap warnings

  asdm of logging of information

  logging - the id of the device hostname

  host of logging inside the 10.1.1.230

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-server protocol nt AD

  AAA-server host 10.1.1.108 AD (inside)

  NT-auth-domain controller 10.1.1.108

  Enable http server

  http 10.1.0.0 255.255.252.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 10.1.0.0 255.255.252.0 inside

  SSH timeout 20

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group vpntest strategy

  Group vpntest policy attributes

  value of 10.1.1.108 WINS server

  Server DNS 10.1.1.108 value

  Protocol-tunnel-VPN IPSec l2tp ipsec

  disable the password-storage

  disable the IP-comp

  Re-xauth disable

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpntest_splitTunnelAcl

  value by default-domain XXX.com

  disable the split-tunnel-all dns

  Dungeon-client-config backup servers

  the address value vpnpool pools

  admin WeiepwREwT66BhE9 encrypted privilege 15 password username

  username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

  the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

  tunnel-group vpntest type remote access

  tunnel-group vpntest General attributes

  address vpnpool pool

  authentication-server-group AD

  authentication-server-group (inside) AD

  Group Policy - by default-vpntest

  band-Kingdom

  vpntest group tunnel ipsec-attributes

  pre-shared-key BEKey123456

  NOCHECK Peer-id-validate

  !

  !

  privilege level 3 mode exec cmd command perfmon

  privilege level 3 mode exec cmd ping command

  mode privileged exec command cmd level 3

  logging of the privilege level 3 mode exec cmd commands

  privilege level 3 exec command failover mode cmd

  privilege level 3 mode exec command packet cmd - draw

  privilege show import at the level 5 exec mode command

  privilege level 5 see fashion exec running-config command

  order of privilege show level 3 exec mode reload

  privilege level 3 exec mode control fashion show

  privilege see the level 3 exec firewall command mode

  privilege see the level 3 exec mode command ASP.

  processor mode privileged exec command to see the level 3

  privilege command shell see the level 3 exec mode

  privilege show level 3 exec command clock mode

  privilege exec mode level 3 dns-hosts command show

  privilege see the level 3 exec command access-list mode

  logging of orders privilege see the level 3 exec mode

  privilege, level 3 see the exec command mode vlan

  privilege show level 3 exec command ip mode

  privilege, level 3 see fashion exec command ipv6

  privilege, level 3 see the exec command failover mode

  privilege, level 3 see fashion exec command asdm

  exec mode privilege see the level 3 command arp

  command routing privilege see the level 3 exec mode

  privilege, level 3 see fashion exec command ospf

  privilege, level 3 see the exec command in aaa-server mode

  AAA mode privileged exec command to see the level 3

  privilege, level 3 see fashion exec command eigrp

  privilege see the level 3 exec mode command crypto

  privilege, level 3 see fashion exec command vpn-sessiondb

  privilege level 3 exec mode command ssh show

  privilege, level 3 see fashion exec command dhcpd

  privilege, level 3 see the vpnclient command exec mode

  privilege, level 3 see fashion exec command vpn

  privilege level see the 3 blocks from exec mode command

  privilege, level 3 see fashion exec command wccp

  privilege see the level 3 exec command mode dynamic filters

  privilege, level 3 see the exec command in webvpn mode

  privilege control module see the level 3 exec mode

  privilege, level 3 see fashion exec command uauth

  privilege see the level 3 exec command compression mode

  level 3 for the show privilege mode configure the command interface

  level 3 for the show privilege mode set clock command

  level 3 for the show privilege mode configure the access-list command

  level 3 for the show privilege mode set up the registration of the order

  level 3 for the show privilege mode configure ip command

  level 3 for the show privilege mode configure command failover

  level 5 mode see the privilege set up command asdm

  level 3 for the show privilege mode configure arp command

  level 3 for the show privilege mode configure the command routing

  level 3 for the show privilege mode configure aaa-order server

  level mode 3 privilege see the command configure aaa

  level 3 for the show privilege mode configure command crypto

  level 3 for the show privilege mode configure ssh command

  level 3 for the show privilege mode configure command dhcpd

  level 5 mode see the privilege set privilege to command

  privilege level clear 3 mode exec command dns host

  logging of the privilege clear level 3 exec mode commands

  clear level 3 arp command mode privileged exec

  AAA-server of privilege clear level 3 exec mode command

  privilege clear level 3 exec mode command crypto

  privilege clear level 3 exec command mode dynamic filters

  level 3 for the privilege cmd mode configure command failover

  clear level 3 privilege mode set the logging of command

  privilege mode clear level 3 Configure arp command

  clear level 3 privilege mode configure command crypto

  clear level 3 privilege mode configure aaa-order server

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

  : end

  Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

  The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

  On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.