ASA 5520 high availability

Similar Questions

• ASA Firewpower high availability

  Hello friends

  In the past, I worked several times with the ASA with CX module. If you want to install a pair of failover with two modules CX, you only need a subscription (for expamle WSE, IPS, STROKE), and then PRSM allows to assign licenses to the current active device.

  Now with the fire power module, I read the guide for many times and not be able to determine if we wanted to implement an asset I m / c pair Stanby, we need a license for each firewall? Or just we need a license for two firewalls?

  Plase, do not hesitate to ask as much as necessary information. Any comments or document will be appreciated.

  Best regards!

  Each module power of fire needs a single licence assigned from the Management Center management FireSIGHT (aka Defense Center).

  This also applies if they are part of the ASAs in an HA pair, a cluster, or completely different.

• Change of SSL/TLS group Diffie-Hellman on ASA 5520

  dh-group SSL control was introduced in 9.3 (2) which is not available to ASA 5520. Is others possible to force ssl vpn to use the diffie-hellman > 1024 bits on this system?

  Sorry miss-read the question.  As far as I know, we can't specify the Diffie-Hellman on the SAA group before 9.3 (2).

  --

  Please do not forget to select a correct answer and rate useful posts

• UPDATED TO VERSION 8.2 ASA 5520 TO 9.0

  Hello friends,

  I am planning to upgrade my ASA 5520 with version 8.2 to 9.0, so I'll enjoy the benefits of anyconnect for mobile devices. Clearly, I understand that I must pay special attention to:

  • NAT rules.
  • Memory RAM: 2 GB.
  • Add references to the rule over the new versions for mobile and anyconnect
    

    L-ASA-AC-E-5520 = ASA-AC-M-5520 =.

  am I missing anything else? Requirement of Flash? Or pay attention to some other configurations?

  Any comments or document will be appreciated.

  Kind regards!

  You can run the latest version of the AnyConnect client - including mobile clients - with these licenses, even on a SAA with the current code of 8.2-8.2 (5) from now on. While it is a bit old and lack some of the new features, it is a strong and stable version.

  That could save you the trouble to migrate the configuration of your NAT (and other songs) and the upgrade memory.

  Since the series ASA 5500 (5510, 5520 etc.) is end of sales past you have a future limited on these platforms. For example, ASA 9.1 (x) is the last series of releases of code which will be available for them. (The current software on the 5500-X is 9.3 (1).)

• Configuration of high availability.

  Hello

  Please help me to configure high availability for Foglight existing environment, please send me the steps and requirements of pre.

  How many servers can exist in a cluster?

  Capacity how do we need on the primary server and the other servers if there is a failure?

  We currently have 1 unifying and 3 child FMS.

  version: 5.6.10

  Thank you

  Vicky

  Vicky,

  There are 2 very useful field guides that go through the requirements and the Setup process.

  High Availability Guide - http://edocs.quest.com/foglight/5610/doc/wwhelp/wwhimpl/common/html/frameset.htm?context=field&file=HA-field/index.php&single=true

  Federation of field guide-

  http://eDOCS.quest.com/Foglight/5610/doc/wwhelp/wwhimpl/common/HTML/frameset.htm?context=field&file=Federation-field/index.php&single=true

  Note the following points, known issue

  http://eDOCS.quest.com/Foglight/5611/doc/wwhelp/wwhimpl/common/HTML/frameset.htm?context=field&file=HA-field/overview.1.php&single=true

  "A master of the Federation running in mode high availability is not supported. Only children Federated can be run by high availability. »

  Golan

• High availability of components in the design of vWorkspace tips

  Hi all

  Would ask you some advice regarding the design of vWorkspace components highly available. Suppose that vWorkspace components will be deployed in vSphere or hypervisors managed SCVMM hence HA is in place, if the failure of a host. In this situation, if we still need components redundant (n + 1 VMS) vWorkspace?

  On the other note, I understand that we can add a couple of broker for vWorkspace in vWorkspace Management Console connections and based on KB 99163 it would just work. I'm not sure how the traffic would be when an application is web access? As in, I guess that the connection broker news would be 'defined' at the request of the web call to the broker for connections. Or this is done automatically? Access Web would choose randomly from the broker for connections to go?

  Thanks for any advice in advance

  Kind regards

  Cyril

  Hi Cyril,.

  Big questions. As with any IT architecture in layers, you must plan HA and redundancy at all points of failure required by your environment or level of Service (SLA) agreements. For vWorkspace, the center of his universe is SQL and you must plan accordingly the failure and recovery. In some environments, full backup can meet the requirement of HA. In others, full SQL Cluster, Mirroring, replication, or Always-On configurations may be required. With our broker, we recommend N + 1 deployment in most scenarios HA. When you move peripheral components or enabling, you must evaluate each component and needs its impact of failure as well as its valuation to determine the appropriate AP.

  Load balancing between several brokers is done automatically by logic in the client connectors. In the case of Web access, when you configure the site Web Access in the Management Console, it includes broker list in the Web access configuration xml file. As client connectors, Web Access includes balancing logic that distributes the client load on brokers available automatically.

  If you have any questions about specific components and requirements of HA or architecture, please add them in the discussions.

• WLC 5508 high availability

  Hello

  Today I have two WLC 5508 (with license for 100 AP each of them), on a single site.

  The WLC work availability (active-standby).

  However, we have a new scenario, with 02 sites: A and B (attachment).

  I would like to know if it is possible to work as follows:

  The WLC - A as the main controller of site A. WLC - B as a backup (BDC) of WLC.-a.

  The WLC - B that has the PDC site B. WLC - as a backup (BDC) to WLC - B.

  For example:

  If WLC - a falls, site access Points are managed by B WLC site - B and vice versa.

  Is this possible?

  How can I configure the new scenario? Don't forget, there is a site-to-site between Site A and Site b.

  Another point:

  If I add more than 50 APs on Site A. How does the license number?

  Should I buy a license for the two WLC?

  TKS,

  >....

  >.. .is it possible?

  No. , high availability in terms of controller is supposed to be what is said, the backup controller is not 'full' - stby and cannot play other roles.

  M.

• IPSec VPN to asa 5520

  Hello

  First I must admit that I am not very versed in Cisco equipment or in general IPSEC connections so my apologies if I'm doing something really good obviously stupid, but I checked through any kind of things that I could find on the internet on the configuration of IPSEC VPN.

  The setup I have is an asa 5520 (o/s 8.2) firewall which, for now, is connected to a temporary connection beautiful style home broadband for testing purposes. The netopia router is configured to allow ipsec passthrough and redirect 62515 UDP, TCP 10000, 4500 UDP, UDP 500 ports in the asa 5520.

  I'm trying to connein out of a laptop with disabled windows firewall and vpn cisco 5.0.02.0090 client version.

  I ran several attempts through the ipsec configuration wizard options. most of the time that nothing comes in the newspaper to show that a connection was attempted, but there is a way I can set up product options the following on the firewall log:

  4. Sep 24 2010 | 13: 54:29 | 713903 | Group = VPNtest9, IP = 86.44.x.x, error: cannot delete PeerTblEntry

  5: Sep 24 2010 | 13: 54:29 | 713902 | Group = VPNtest9, IP = 86.44.x.x, drop table homologous counterpart does not, no match!

  6. Sep 24 2010 | 13: 54:21 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:21 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  6. Sep 24 2010 | 13: 54:16 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:16 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  6. Sep 24 2010 | 13: 54:11 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:11 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  6. Sep 24 2010 | 13: 54:06 | 302015 | 86.44.x.x | 51905 | 192.168.0.27 | 500 | Built UDP inbound connection 7487 for Internet:86.44.x.x/51905 (86.44.x.x/51905) at identity:192.168.0.27/500 (192.168.0.27/500)

  and this, in the journal of customer:

  Cisco Systems VPN Client Version 5.0.02.0090

  Copyright (C) 1998-2007 Cisco Systems, Inc.. All rights reserved.

  Customer type: Windows, Windows NT

  Running: 5.1.2600 Service Pack 3

  24 13:54:08.250 24/09/10 Sev = Info/4 CM / 0 x 63100002

  Start the login process

  25 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100004

  Establish a secure connection

  26 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100024

  Attempt to connect with the server "213.94.x.x".

  27 13:54:08.437 24/09/10 Sev = Info/6 IKE/0x6300003B

  Attempts to establish a connection with 213.94.x.x.

  28 13:54:08.437 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) at 213.94.x.x

  29 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700008

  IPSec driver started successfully

  30 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  31 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  32 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  33 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  34 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  35 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  36 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  37 13:54:28.484 24/09/10 Sev = Info/4 IKE / 0 x 63000017

  Marking of IKE SA delete (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  38 13:54:28.984 24/09/10 Sev = Info/4 IKE/0x6300004B

  IKE negotiation to throw HIS (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  39 13:54:28.984 24/09/10 Sev = Info/4 CM / 0 x 63100014

  Could not establish the Phase 1 SA with the server '213.94.x.x' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

  40 13:54:28.984 24/09/10 Sev = Info/5 CM / 0 x 63100025

  Initializing CVPNDrv

  41 13:54:28.984 24/09/10 Sev = Info/6 CM / 0 x 63100046

  Set indicator established tunnel to register to 0.

  42 13:54:28.984 24/09/10 Sev = Info/4 IKE / 0 x 63000001

  Signal received IKE to complete the VPN connection

  43 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  44 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  45 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  46 13:54:29.187 24/09/10 Sev = Info/4 IPSEC/0x6370000A

  IPSec driver successfully stopped

  I have connectivity full http from the internet to a machine inside the asa 5520 so I think that the static routing and NAT'ing should be ok, but I am pleased to provide you with all the details.

  Can you see what I'm doing wrong?

  Thank you

  Sam

  Pls add the following policy:

  crypto ISAKMP policy 10

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  You can also run debug on the ASA:

  debugging cry isa

  debugging ipsec cry

  and retrieve debug output after trying to connect.

• Tunnel VPN ASA 5520 (DMZ + INSIDE) destined for OUTSIDE

  I can't find any reference to anywhere else.

  We have an ASA 5520 to our site HQ (inside the network) with several regional subnets on the DMZ interface.

  We need connectivity VPN Site to Site between the INSIDE and a remote control on the OUTSIDE of the site, as well as between the DMZ subnets and even outside the site. The interface from the OUTSIDE of the SAA must be local VPN endpoint for all tunnels.

  I created a S2S VPN between the INSIDE and the OUTSIDE site and it works great.

  When I create a VPN S2S tunnel between a site of DMZ and even outside the site (using the same settings the and remote, but with a cryptomap different because the local subnet (DMZ) is different from the other inside the subnet, the traffic gets the mapping (show crypto isakmp his) to the same cryptomap that was created for the access to the tunnel from the OUTSIDE) , instead of to the new cryptomap, so remote endpoint deletes it, and traffic also causes SPI incorrect of for the remote endpoint, which makes the original INTERIOR outside OF THE VPN tunnel to fall from time to time.

  Is this a bug?

  I also did a local S2S VPN tunnel configuration test of networks as everything INSIDE and the DMZ. With the help of the wizard VPN S2S leads ASA only to create a NAT rule exempted for the subnet on the INSIDE interface. Can I manually create another tax-exempt NAT rule to the side of the DMZ and use this a S2S tunnel to connect sites inside and DMZ to the remote OFF-SITE in a connection profile?

  I'm building a Rube Goldberg?

  Thank you

  George

  Hi George,.

  It seems you have a situation overlapping it, are you sure that subnets inside did not overlap with the networks from the DMZ?  A package tracer could clarify wha that the ASA is actually sending.

  In addition, you can merge the two interfaces on the same card encryption if you wish, just make sure that the NAT is configured correctly.   For example; Source NAT (all, outside) static...

  It may be useful

  -Randy-

• IPCCX high availability

  Does anyone know if Cisco will provide redundancy standby high availability of IPCC express?

  Chris

  Search in the next major version of the IPCC Express. Last I heard it was scheduled for release next month some time.

  Jim

• Deployment of high availability of the IPCC 4.5

  In a future HD architecture implementation, the voice service will provide CallManager 5.0, that will integrate with 4.5 of the IPCC. 4.5 (required with 5.0 CM) IPCC does implement a high availability. How can we ensure that technical support continues to operate if the IPCC goes down? One possibility might be to configure CM such that if the IPCC goes down, all the number of help desk calls are automatically and immediately headed to a group (which includes all extensions help desk). This redirection can be configured in CM? Is there a better option?

  Thanks in advance,

  SB

  This is your best bet. On the road Points for your call center just put the call before busy, no answer and failure to the fighter pilot. Thus, when the IPCC Express Server is down it will sent to your fighter pilot.

  Please evaluate the useful messages.

  adignan - berbee

• ASA 5520 to Juniper ss505m vpn

  I'm having a problem with the vpn site to site between a asa 5520 and Juniper ss 505 m. The tunnel rises, but we seem unable to pass traffic through the vpn tunnel.  It appears on the remote side makes a connection to the ftp server on the Local Server, but is never prompt identification of connection information.

  April 19, 2016 13:27:13 SQL-B2B-01: % ASA-4-402116: IPSEC: received a package ESP x.x (SPI = 0xD167A5E8, sequence number = 0xD).

  241.90 (user = X.X.241.90) at X.X.167.230.  Inside the package décapsulés does not match policy negotiated in the SA.  The

  package specifies its destination as its Protocol TCP, its source such as X.X.2.68 and X.X.167.233.  SA specifies its loc

  proxy of Al X.X.167.233/255.255.255.255/tcp/5376 and his remote_proxy as X.X.2.68/255.255.255.255/tcp/5376.

  list of remote ip-group of objects allowed extended West Local Group object

  NAT static Local_Pub Local destination (indoor, outdoor) static source Remote

  Crypto ipsec ikev1 transform-set esp-aes-256 Remote esp-sha-hmac

  West-map 95 crypto card is the Remote address
  card crypto West-map 95 set peer X.X.241.90
  map West-map 95 set transform-set Remote ikev1 crypto
  card crypto West-map 95 defined security-association life seconds 28800

  Juniper-

  "Remote-ftp" X.X.167.233 255.255.255.255

  Gateway proposal P1 preshare "[email protected]/ * /" proposal "pre-g2-aes256-sha-28800.

  P2-proposal "no-pfs-esp-aes256-sha-28800" No. - pfs esp aes256 sha-1 second 28800

  ----------------------

  the top of the policy of "Trust" to "Untrust" "X.X.2.68/32" "Remote-ftp' 'ftp' vpn"Remote-vpn"tunnel log

  put on top of the "Untrust" policy to the "Trust" "Remote-ftp' 'X.X.2.68/32' 'ftp' vpn"SonoraQ-vpn"tunnel sign

  I do not know Juniper, but it seems that it is trying to negotiate the use of only 5376/tcp on the tunnel, when it should be negotiated just Protocol "ip".

• VPN site to site & outdoor on ASA 5520 VPN client

  Hi, I'm jonathan rivero.

  I have an ASA 5520 Version 8.0 (2), I configured the site-to-site VPN and works very well, in the other device, I configured the VPN Client for remote users and works very well, but I try to cofigure 2 VPNs on ASA 5520 on the same outside interface and I have the line "outside_map interface card crypto outdoors (for VPN client). , but when I set up the "crypto map VPNL2L outside interface, it replaces the command', and so I can have only a single connection.

  the executed show.

  ASA1 (config) # sh run

  : Saved

  :

  ASA Version 8.0 (2)

  !

  hostname ASA1

  activate 7esAUjZmKQSFDCZX encrypted password

  names of

  !

  interface Ethernet0/0

  nameif inside

  security-level 100

  address 172.16.3.2 IP 255.255.255.0

  !

  interface Ethernet0/1

  nameif outside

  security-level 0

  IP 200.20.20.1 255.255.255.0

  !

  interface Ethernet0/1.1

  VLAN 1

  nameif outside1

  security-level 0

  no ip address

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/5

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  2KFQnbNIdI.2KYOU encrypted passwd

  passive FTP mode

  object-group, net-LAN

  object-network 172.16.0.0 255.255.255.0

  object-network 172.16.1.0 255.255.255.0

  object-network 172.16.2.0 255.255.255.0

  object-network 172.16.3.0 255.255.255.0

  object-group, NET / remote

  object-network 172.16.100.0 255.255.255.0

  object-network 172.16.101.0 255.255.255.0

  object-network 172.16.102.0 255.255.255.0

  object-network 172.16.103.0 255.255.255.0

  object-group network net-poolvpn

  object-network 192.168.11.0 255.255.255.0

  access list outside nat extended permit ip net local group object all

  access-list extended sheep allowed ip local object-group net object-group net / remote

  access-list extended sheep allowed ip local object-group net net poolvpn object-group

  access-list splittun-vpngroup1 extended permitted ip local object-group net net poolvpn object-group

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  outside1 MTU 1500

  IP local pool ippool 192.168.11.1 - 192.168.11.100 mask 255.255.255.0

  no failover

  ICMP unreachable rate-limit 100 burst-size 10

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 access list outside nat

  Route outside 0.0.0.0 0.0.0.0 200.20.20.1 1

  Route inside 172.16.0.0 255.255.255.0 172.16.3.2 1

  Route inside 172.16.1.0 255.255.255.0 172.16.3.2 1

  Route inside 172.16.2.0 255.255.255.0 172.16.3.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout, uauth 0:05:00 absolute

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec kilobytes of life security-association 400000

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  card crypto VPNL2L 1 match for sheep

  card crypto VPNL2L 1 set peer 200.30.30.1

  VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 20

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  !

  !

  internal vpngroup1 group policy

  attributes of the strategy of group vpngroup1

  banner value +++ welcome to Cisco Systems 7.0. +++

  value of 192.168.0.1 DNS server 192.168.1.1

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value splittun-vpngroup1

  value by default-ad domain - domain.local

  Split-dns value ad - domain.local

  the address value ippool pools

  username password asa1 VRTlLlJ48/PoDKjS encrypted privilege 15

  tunnel-group 200.30.30.1 type ipsec-l2l

  IPSec-attributes tunnel-group 200.30.30.1

  pre-shared-key *.

  type tunnel-group vpngroup1 remote access

  tunnel-group vpngroup1 General-attributes

  ippool address pool

  Group Policy - by default-vpngroup1

  vpngroup1 group of tunnel ipsec-attributes

  pre-shared-key *.

  context of prompt hostname

  Cryptochecksum:00000000000000000000000000000000

  : end

  ASA2 (config) #sh run

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  86400 seconds, duration of life crypto ipsec security association
  Crypto ipsec kilobytes of life security-association 400000
  card crypto VPNL2L 1 match for sheep
  card crypto VPNL2L 1 set peer 200.30.30.1
  VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
  VPNL2L interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 20
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  tunnel-group 200.30.30.1 type ipsec-l2l
  IPSec-attributes tunnel-group 200.30.30.1
  pre-shared key cisco

  my topology:

  

  I try with the following links, but did not work

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080912cfd.shtml

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml

  Best regards...

  "" I thing both the force of the SAA with the new road outside, why is that? ".

  without the road ASA pushes traffic inward, by default.

  In any case, this must have been a learning experience.

  Hopefully, this has been no help.

  Please rate, all the helful post.

  Thank you

  Rizwan Muhammed.

• IPS high-availability Solution

  Hi all

  obligation to have redundancy for appliance IPS placed on data center design, I dug on Cisco docs but found the resilience and the HA (High Availability) from the point of view of IPS could take place in the side of switches (HSRP/Eth channel balance).

  is there a visible way to implement high availability of dynamically!

  Kind regards

  Belal

  Yes Belal, both of the things mentioned by you are right. There is no function available which allows "failover" communications between IPS two boxes as do Cisco firewalls.

  Yes Etherchannel load balance traffic to each pair of IP from sensor single src - dst.

  Concerning

  Farrukh

• Cisco ASA 5520, 8.02, 4GE SSM, IPS?

  I have an ASA 5520 with 4GE SSM module.

  The ASDM, I see IPS basic signatures... anyway to upgrade these signatures, add to, etc.?

  Not really, you must purchase the AIP - SSM module for this.

  Concerning

  Farrukh