ASA ASA from Site to Site VPN IPSec Tunnel

Similar Questions

• Cisco ASA Site to Site VPN IPSEC and NAT question

  Hi people,

  I have a question about the two Site to Site VPN IPSEC and NAT. basically what I want to achieve is to do the following:

  ASA2 is at HQ and ASA1 is a remote site. I have no problem setting a static static is a Site to IPSEC VPN between sites. Guests residing in 10.1.0.0/16 are able to communicate with hosts in 192.168.1.0/24, but what I want is to configure the NAT with IPSEC VPN for this host to 10.1.0.0/16 will communicate with hosts in 192.168.1.0/24 with translated addresses

  Just an example:

  N2 host (10.1.0.1/16) contacted N1 192.168.1.5 with destination host say 10.23.1.5 No 192.168.1.5 (notice the last byte is the same in the present case,.5)

  The translation still for the rest of the communication (host pings ip destination host 10.23.1.6 N3 N2 not 192.168.1.6 new last byte is the same)

  It sounds a bit confusing to me, but I've seen this type of configuration before when I worked for the supplier of managed services where we have given our customers (Ipsec Site to Site VPN with NAT, don't know how it was setup)

  Basically we contact the customer via site-to-site VPN hosts but their real address were hidden and we used as translated address more high 10.23.1.0/24 instead of (real) 192.168.1.0/24, last byte must be the same.

  Grateful if someone can shed some light on this subject.

  Hello

  OK so went with the old format of NAT configuration

  It seems to me that you could do the following:

  • Configure the ASA1 with static NAT strategy
    • access-list L2LVPN-POLICYNAT allowed ip 192.168.1.0 255.255.255.0 10.1.0.0 255.255.0.0
    • public static 10.23.1.0 (inside, outside) access-list L2LVPN-POLICYNAT
  • Because the above is a static NAT of the policy, this means that the translation will be made only when the destination network is 10.1.0.0/16
  • If you have for example a PAT basic configuration to inside-> external traffic, the above NAT configuration and the custom of the actual configuration of PAT interfere with eachother
  • ASA2 side, you can normally configure NAT0 / NAT Exemption for the 10.1.0.0/16 network
    • Note of the INTERIOR-SHEEP access-list SHEEP L2LVPN
    • the permitted INSIDE SHEEP 10.1.0.0 ip access list 255.255.0.0 10.23.1.0 255.255.255.0
    • NAT (inside) 0-list of access to the INTERIOR-SHEEP
  • You will need to consider that your access-list defining the VPN encrypted L2L traffic must reflect the new NAT network
    • ASA1: allowed to access-list L2LVPN-ENCRYPTIONDOMAIN ip 10.23.1.0 255.255.255.0 10.1.0.0 255.255.0.0
    • ASA2: list L2LVPN-ENCRYPTIONDOMAIN allowed ip 10.1.0.0 access 255.255.0.0 10.23.1.0 255.255.255.0

  I could test this configuration to work tomorrow but I would like to know if it works.

  Please rate if this was helpful

  -Jouni

• Site-to-Site VPN IPSEC falls intermittently

  Site-to-Site VPN IPSEC falls intermittently

  I am currently having a problem with a VPN from Site to Site traffic not only not intermittently. When the problem occurs, I can't Ping the remote site to the AC Site. But I can solve the problem by Pinging from HQ at the Remote Site. My network is currently configured as follows

  -------HQ------

  7.0 (4) version of pix 515 with card Ethernet 4 ports.

  Outside of the interface connected to the Broadband DSL link.

  Outside2 Interface connected to the second link DSL broadband

  -Distance-

  I have 4 Remote Sites. 2 sites connect you to each connection to wide band at HQ to spread the load to HQ

  6.3 (5) pix 501 version

  # The problem #.

  All VPN establishes successfully to the HQ Pix

  Intermittently, a remote site will report that they cannot connect to servers/services in the HQ. When I do a show crypto ipsec's and see the crypto isakmp his headquarters there is no entry for the remote site. However when I do the same on the remote site there is an entry for the HQ. With debugging on the remote site pix I try to ping from a pc to the HQ server and I get the following (see below). If I do a "ipsec Isakmp security association claire crypto ' and ' clear crypto ipsec his ' on the pix of remote site, then I can successfully ping all servers in headquarters.

  This problem seems to have taken place only when I upgraded the pix of a 501 to 515 and added another 2 remote sites and a second broadband, as described above. I'm afraid that there is a problem with software version 7 Pix. Any advice would be greatly appreciated.

  Console record Carrick-PIX01 (config) # 7

  Carrick-PIX01 (config) # ter Lun

  Output Carrick-PIX01 (config) #.

  Carrick-PIX01 # debug crypto ipsec

  Carrick-PIX01 # debug crypto isakmp

  Carrick-PIX01 #.

  ISAKMP (0:0): sending of NAT - T vendor ID - rev 2 & 3

  ISAKMP (0): early changes of Main Mode

  ISAKMP (0): retransmission of the phase 1 (0)...

  ISAKMP (0): retransmission of the phase 1 (1)...

  ISAKMP (0): retransmission of the phase 1 (2)...

  Carrick-PIX01 #.

  Carrick-PIX01 #.

  ISAKMP (0): retransmission of the phase 1 (3)...

  Carrick-PIX01 #.

  Carrick-PIX01 #.

  ISAKMP (0): retransmission of the phase 1 (4)... IPSec (key_engine): request timer shot: count = 1,.

  (identity) local = OUTER-IP, distance = 86.43.74.16,.

  local_proxy = LAN-OFFICE/255.255.255.0/0/0 (type = 4),

  remote_proxy = 194.x.x.x.x.255.0/0/0 (type = 4)

  ISAKMP (0): delete SA: CBC EXTERNAL IP, dst 86.43.74.16

  ISADB: Reaper checking HIS 0x10c167c, id_conn = 0 DELETE IT!

  Peer VPN: ISAKMP: Peer Info for 86.43.74.16/500 not found - peer: 1

  ISADB: Reaper checking HIS 0x10ca914, id_conn = 0

  Can force you the ISAKMP Keepalive, value from IPSec Security Association idle time and on the other. The problem should be solved

  ISAKMP crypto keepalive 30

  Crypto ipsec security association temps_inactivite 60

  Let me know if it helps

• Site to Site VPN IPsec IPv6 on issue of routers-Tunnel

  Hi, I am experiencing a problem can any one address the question below and let me know the solution. I have two routers and try to build "Site to Site VPN IPsec IPv6". I followed orders from Cisco and community document but when I apply my profile of ipsec for tunnel interfaces, that the tunnel is down.

  https://supportforums.Cisco.com/docs/doc-27009

  Ali,

  VTI tunnels are meant to be broken when there is no active negotiated spinnakers.

  The tunnel will go towards up/face upwards when there is a means of transport of packages - i.e. the SPIs are present.

  You can control the order spinnakers 'show peer's crypto ipsec '.

  For debugging:

  Debug crypto isa

  Debug crypto ipsec

  M.

• ASA from Site to Site and SSL VPN stop working

  Thanks in advance for any advice

  We have an ASA 5510, users were able to connect via to all connect without any problems. We opened a new office with an ASA 5505 and decided to give VPN site-to-site on IPSec. We used the basic wizard and everything went smoothly at both ends. However, users who always used SSL VPN says so that they can connect to the original site, they are no longer in their RDP virtual machines or get anywhere on the network. I don't know why something like this can happen.

  You can change the SSL VPN DHCP scope to give a different subnet for IP addresses. Maybe try 192.168.10.0 255.255.255.0. Let me know if you can and if that corrects the issue.

  Sent by Cisco Support technique iPhone App

• Installation of site to site VPN IPSec using PIX and ASA

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  I am a site configuration to site IPSec VPN using a PIX515E to site A and ASA5520 to Site B.

  I have attached the lab diagram. Consider PIX and ASA are in default configuration, which means that nothing is configured on both devices.

  According to the scheme

  ASA5520

  External interface is the level of security 11.11.10.1/248 0

  The inside interface is 172.16.9.2/24 security level 100

  Default route is 0.0.0.0 0.0.0.0 11.11.10.2 1

  PIX515E

  External interface is the level of security 123.123.10.2/248 0

  The inside interface is 172.16.10.1/24 security level 100

  Default route is 0.0.0.0 0.0.0.0 123.123.10.1 1

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  Could someone tell me how to set up this configuration? I tried but didn't workout. Here is the IKE protocol I have used.

  IKE information:

  IKE Encrytion OF

  MD5 authentication method

  Diffie Helman Group 2

  Failure to life

  IPSEC information:

  IPsec encryption OF

  MD5 authentication method

  Failure to life

  Please enter the following command

  on asa

  Sysopt connection permit VPN

  on pix not sure of the syntax, I think it is

  Permitted connection ipsec sysopt

  What we are trying to do here is basically allowing vpn opening ports

  Alternatively you can open udp 500 and esp (or port ip 50) out to in on the two firewalls

• ASA: VPN IPSEC Tunnel from 5505(ver=8.47) to 5512 (ver = 9.23)

  Hi-

  We have connected tunnel / VPN configuration between an ASA 5505 - worm = 8.4 (7) and 5512 - worm = 9.2 (3).
  We can only ping in a sense - 5505 to the 5512, but not of vice-versa(5512 to 5505).

  Networks:

  Local: 192.168.1.0 (answering machine)
  Distance: 192.168.54.0 (initiator)

  See details below on our config:

  SH run card cry

  card crypto outside_map 2 match address outside_cryptomap_ibfw
  card crypto outside_map 2 pfs set group5
  outside_map 2 peer XX crypto card game. XX.XXX.XXX
  card crypto outside_map 2 set transform-set ESP-AES-256-SHA ikev1
  crypto map outside_map 2 set ikev2 AES256 ipsec-proposal

  outside_map interface card crypto outside

  Note:
  Getting to hit numbers below on rules/ACL...

  SH-access list. I have 54.0

  permit for access list 6 outside_access_out line scope ip 192.168.1.0 255.255.255.0 192.168.54.0 255.255.255.0 (hitcnt = 15931) 0x01aecbcc
  permit for access list 1 outside_cryptomap_ibfw line extended ip object NETWORK_OBJ_192.168.1.0_24 object NETWORK_OBJ_192.168.54.0_24 (hitcnt = 3) 0xa75f0671
  access-list 1 permit line outside_cryptomap_ibfw extended ip 192.168.1.0 255.255.255.0 192.168.54.0 255.255.255.0 (hitcnt = 3) 0xa75f0671

  SH run | I have access-group
  Access-group outside_access_out outside interface

  NOTE:
  WE have another working on the 5512 - VPN tunnel we use IKE peer #2 below (in BOLD)...

  HS cry his ikev1

  IKEv1 SAs:

  HIS active: 2
  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
  Total SA IKE: 2

  1 peer IKE: XX. XX.XXX.XXX
  Type: L2L role: answering machine
  Generate a new key: no State: MM_ACTIVE
  2 IKE peers: XXX.XXX.XXX.XXX
  Type: L2L role: answering machine
  Generate a new key: no State: MM_ACTIVE

  SH run tunnel-group XX. XX.XXX.XXX
  tunnel-group XX. XX.XXX.XXX type ipsec-l2l
  tunnel-group XX. XX.XXX.XXX General-attributes
  Group - default policy - GroupPolicy_XX.XXX.XXX.XXX
  tunnel-group XX. XX.XXX.XXX ipsec-attributes
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.

  SH run | I have political ikev1

  ikev1 160 crypto policy
  preshared authentication
  aes-256 encryption
  Group 5
  life 86400

  SH run | I Dynamics
  NAT interface dynamic obj - 0.0.0.0 source (indoor, outdoor)
  NAT source auto after (indoor, outdoor) dynamic one interface

  NOTE:
  To from 5512 at 5505-, we can ping a host on the remote network of ASA local

  # ping inside the 192.168.54.20
  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 192.168.54.20, wait time is 2 seconds:
  !!!!!
  Success rate is 100 per cent (5/5), round-trip min/avg/max = 30/32/40 ms

  Determination of 192.168.1.79 - local host route to 192.168.54.20 - remote host - derivation tunnel?

  The IPSEC tunnel check - seems OK?

  SH crypto ipsec his
  Interface: outside
  Tag crypto map: outside_map, seq num: 2, local addr: XX.XXX.XXX.XXX

  outside_cryptomap_ibfw to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.54.0 255.255.255.0
  local ident (addr, mask, prot, port): (192.168.1.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (192.168.54.0/255.255.255.0/0/0)
  current_peer: XX. XX.XXX.XXX

  #pkts program: 4609, #pkts encrypt: 4609, #pkts digest: 4609
  #pkts decaps: 3851, #pkts decrypt: 3851, #pkts check: 3851
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 4609, model of #pkts failed: 0, #pkts Dang failed: 0
  success #frag before: 0, failures before #frag: 0, #fragments created: 0
  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
  #TFC rcvd: 0, #TFC sent: 0
  #Valid errors ICMP rcvd: 0, #Invalid ICMP errors received: 0
  #send errors: 0, #recv errors: 0

  local crypto endpt. : XX.XXX.XXX.XXX/0, remote Start crypto. : XX. XX.XXX.XXX/0
  Path mtu 1500, ipsec 74 (44) generals, media, mtu 1500
  PMTU time remaining: 0, political of DF: copy / df
  Validation of ICMP error: disabled, TFC packets: disabled
  current outbound SPI: CDC99C9F
  current inbound SPI: 06821CBB

  SAS of the esp on arrival:
  SPI: 0x06821CBB (109190331)
  transform: aes-256-esp esp-sha-hmac no compression
  running parameters = {L2L, Tunnel, group 5 PFS, IKEv1}
  slot: 0, id_conn: 339968, crypto-card: outside_map
  calendar of his: service life remaining (KB/s) key: (3914789/25743)
  Size IV: 16 bytes
  support for replay detection: Y
  Anti-replay bitmap:
  0xFFFFFFFF to 0xFFFFFFFF
  outgoing esp sas:
  SPI: 0xCDC99C9F (3452542111)
  transform: aes-256-esp esp-sha-hmac no compression
  running parameters = {L2L, Tunnel, group 5 PFS, IKEv1}
  slot: 0, id_conn: 339968, crypto-card: outside_map
  calendar of his: service life remaining (KB/s) key: (3913553/25743)
  Size IV: 16 bytes
  support for replay detection: Y
  Anti-replay bitmap:
  0x00000000 0x00000001

  --> The local ASA 5512 - where we have questions - tried Packet Tracer... seems we receive requests/responses...

  SH cap CAP

  34 packets captured

  1: 16:41:08.120477 192.168.1.79 > 192.168.54.20: icmp: echo request
  2: 16:41:08.278138 192.168.54.20 > 192.168.1.79: icmp: echo request
  3: 16:41:08.278427 192.168.1.79 > 192.168.54.20: icmp: echo reply
  4: 16:41:09.291992 192.168.54.20 > 192.168.1.79: icmp: echo request
  5: 16:41:09.292282 192.168.1.79 > 192.168.54.20: icmp: echo reply

  --> On the ASA 5505 distance - we can ping through the 5512 to the local host (192.168.1.79)

  SH cap A2

  42 packets captured

  1: 16:56:16.136559 802. 1 q vlan P0 192.168.54.20 #1 > 192.168.1.79: icmp: echo request
  2: 16:56:16.168860 802. 1 q vlan P0 192.168.1.79 #1 > 192.168.54.20: icmp: echo reply
  3: 16:56:17.140434 802. 1 q vlan P0 192.168.54.20 #1 > 192.168.1.79: icmp: echo request
  4: 16:56:17.171652 802. 1 q vlan P0 192.168.1.79 #1 > 192.168.54.20: icmp: echo reply
  5: 16:56:18.154426 802. 1 q vlan P0 192.168.54.20 #1 > 192.168.1.79: icmp: echo request
  6: 16:56:18.186178 802. 1 q vlan P0 192.168.1.79 #1 > 192.168.54.20: icmp: echo reply
  7: 16:56:19.168417 802. 1 q vlan P0 192.168.54.20 #1 > 192.168.1.79: icmp: echo request

  --> Package trace on 5512 does no problem... but we cannot ping from host to host?

  entry Packet-trace within the icmp 192.168.1.79 8 0 detailed 192.168.54.20

  Phase: 4
  Type: CONN-SETTINGS
  Subtype:
  Result: ALLOW
  Config:
  class-map default class
  match any
  Policy-map global_policy
  class class by default
  Decrement-ttl connection set
  global service-policy global_policy
  Additional information:
  Direct flow from returns search rule:
  ID = 0x7fffa2d0ba90, priority = 7, area = conn-set, deny = false
  hits = 4417526, user_data = 0x7fffa2d09040, cs_id = 0 x 0, use_real_addr, flags = 0 x 0 = 0 protocol
  IP/ID=0.0.0.0 SRC, mask = 0.0.0.0, port = 0, = 0 tag
  IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, tag = 0, dscp = 0 x 0
  input_ifc = output_ifc = any to inside,

  Phase: 5
  Type: NAT
  Subtype:
  Result: ALLOW
  Config:
  NAT interface dynamic obj - 0.0.0.0 source (indoor, outdoor)
  Additional information:
  Definition of dynamic 192.168.1.79/0 to XX.XXX.XXX.XXX/43904
  Direct flow from returns search rule:
  ID = 0x7fffa222d130, priority = 6, area = nat, deny = false
  hits = 4341877, user_data = 0x7fffa222b970, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol
  IP/ID=0.0.0.0 SRC, mask = 0.0.0.0, port = 0, = 0 tag
  IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, tag = 0, dscp = 0 x 0
  input_ifc = inside, outside = output_ifc

  ...

  Phase: 14
  Type: CREATING STREAMS
  Subtype:
  Result: ALLOW
  Config:
  Additional information:
  New workflow created with the 7422689 id, package sent to the next module
  Information module for forward flow...
  snp_fp_tracer_drop
  snp_fp_inspect_ip_options
  snp_fp_inspect_icmp
  snp_fp_translate
  snp_fp_adjacency
  snp_fp_fragment
  snp_ifc_stat

  Information for reverse flow...
  snp_fp_tracer_drop
  snp_fp_inspect_ip_options
  snp_fp_translate
  snp_fp_inspect_icmp
  snp_fp_adjacency
  snp_fp_fragment
  snp_ifc_stat

  Result:
  input interface: inside
  entry status: to the top
  entry-line-status: to the top
  output interface: outside
  the status of the output: to the top
  output-line-status: to the top
  Action: allow

  --> On remote ASA 5505 - Packet track is good and we can ping remote host very well... dunno why he "of Nations United-NAT?

  Destination - initiator:
   
  entry Packet-trace within the icmp 192.168.54.20 8 0 detailed 192.168.1.79
   
  ...
  Phase: 4
  Type: UN - NAT
  Subtype: static
  Result: ALLOW
  Config:
  NAT (inside, outside) static source NETWORK_OBJ_192.168.54.0_24 NETWORK_OBJ_192.168.54.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
  Additional information:
  NAT divert on exit to the outside interface
  Untranslate 192.168.1.79/0 to 192.168.1.79/0
  ...

  Summary:
  We "don't" ping from a host (192,168.1.79) on 5512 - within the network of the 5505 - inside the network host (192.168.54.20).
  But we can ping the 5505 - inside the network host (192.168.54.20) 5512 - inside the network host (192.168.1.79).

  Please let us know what other details we can provide to help solve, thanks for any help in advance.

  -SP

  Well, I think it is a NAT ordering the issue.

  Basically as static and this NAT rule-

  NAT interface dynamic obj - 0.0.0.0 source (indoor, outdoor)

  are both in article 1 and in this article, it is done on the order of the rules so it does match the dynamic NAT rule rather than static because that seems to be higher in the order.

  To check just run a 'sh nat"and this will show you what order everthing is in.

  The ASA is working its way through the sections.

  You also have this-

  NAT source auto after (indoor, outdoor) dynamic one interface

  which does the same thing as first statement but is in section 3, it is never used.

  If you do one of two things-

  (1) configure the static NAT statement is above the dynamic NAT in section 1 that is to say. You can specify the command line

  or

  (2) remove the dynamic NAT of section 1 and then your ASA will use the entry in section 3.

  There is a very good document on this site for NAT and it is recommended to use section 3 for your general purpose NAT dynamic due precisely these questions.

  It is interesting on your ASA 5505 you duplicated your instructions of dynamic NAT again but this time with article 2 and the instructions in section 3 that is why your static NAT works because he's put in correspondence before all your dynamic rules.

  The only thing I'm not sure of is you remove the dynamic NAT statement in article 1 and rely on the statement in section 3, if she tears the current connections (sorry can't remember).

  Then you can simply try to rearrange so your static NAT is above it just to see if it works.

  Just in case you want to see the document here is the link-

  https://supportforums.Cisco.com/document/132066/ASA-NAT-83-NAT-operation-and-configuration-format-CLI

  Jon

• Site to Site VPN IPSEC for multisite with dual ISP failover

  Hello world

  I have total 6 ASA 5505, I already built failover with double tis. Now, I want to configure site 2 site VPN for all 3 sites. Each site has 2 firewall.

  I just built a config for 2 a site WHAT VPN here is the config for a single site.

  local ip address: 172.16.100.0

  IP of the pubis: 10.5.1.101, 10.6.1.101

  Remote local ip: 172.16.101.0

  Remote public ip: 10.3.1.101, 10.4.1.101

  Remote local ip: 192.168.0.0

  Remote public ip: 10.1.1.101, 10.2.1.101

  the tunnel on the first 2 firewall configuration:

  IP 172.16.100.0 allow Access-list vpn1 255.255.255.0 172.16.101.0 255.255.255.0

  backupvpn1 ip 172.16.100.0 access list allow 255.255.255.0 172.16.101.0 255.255.255.0

  ip 172.16.100.0 access VPN2 list allow 255.255.255.0 192.168.0.0 255.255.255.0

  backupvpn2 ip 172.16.100.0 access list allow 255.255.255.0 192.168.0.0 255.255.255.0

  IP 172.16.100.0 allow Access-list sheep 255.255.255.0 172.16.101.0 255.255.255.0

  172.16.100.0 IP Access-list sheep 255.255.255.0 allow 192.168.0.0 255.255.255.0

  !

  !

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 0.0.0.0 0.0.0.0

  !

  !

  !

  crypto ISAKMP allow outside

  ISAKMP crypto enable backup

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  !

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac my-set1

  card crypto outside_map 1 match for vpn1

  peer set card crypto outside_map 1 10.3.1.101

  My outside_map 1 transform-set-set1 crypto card

  outside_map interface card crypto outside

  !

  !

  card crypto outside_map 2 match address backupvpn1

  peer set card crypto outside_map 2 10.4.1.101

  My outside_map 2 transform-set-set1 crypto card

  backup of crypto outside_map interface card

  !

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac my-set2

  crypto outside_map 3 game card address vpn2

  peer set card crypto outside_map 3 10.1.1.101

  My outside_map 3 transform-set-set2 crypto card

  outside_map interface card crypto outside

  !

  !

  card crypto 4 correspondence address backupvpn2 outside_map

  peer set card crypto outside_map 4 10.2.1.101

  My outside_map 4 transform-set-set2 crypto card

  backup of crypto outside_map interface card

  !

  !

  !

  tunnel-group 10.3.1.101 type ipsec-l2l

  IPSec-attribute Tunnel-Group 10.3.1.101

  pre-shared key cisco

  ISAKMP keepalive retry 20 3 threshold

  !

  !

  tunnel-group 10.4.1.101 type ipsec-l2l

  IPSec-attribute Tunnel-Group 10.4.1.101

  pre-shared key cisco

  ISAKMP keepalive retry 20 3 threshold

  !

  !

  tunnel-group 10.1.1.101 type ipsec-l2l

  IPSec-attribute Tunnel-Group 10.1.1.101

  pre-shared key cisco

  ISAKMP keepalive retry 20 3 threshold

  !

  !

  tunnel-group 10.2.1.101 type ipsec-l2l

  IPSec-attribute Tunnel-Group 10.2.1.101

  pre-shared key cisco

  ISAKMP keepalive retry 20 3 threshold

  !

  !

  backup of MTU 1500

  If this correct what should I configure other side that I want to finish in front of it. Is my address name vpn1 crypto card must match on the other side or not?

  any suggestion is good...

  Thank you...

  What I mean with the routing is a routing protocol or static routes the SAA can choose between interfaces to establish the tunnel.

  If the ASA has the card encryption applied to two interfaces, then one should be used as primary and the other as backup.

  How will be the ASA choose which is better? Via the routing.

  If you use a routing protocol, the ASA will be known which interface to send packets every time, but if using static routes, you need to change the metric and configuring IP SLA.

  Federico.

• Site to site VPN IPSec

  Hi all,

  Could someone tell me please if on the IPSec VPN (not GRE over IPSec) site to supported routing protocols?

  Thank you.

  Hello

  Well, a Site does not support multicast traffic.

  http://www.ietf.org/RFC/rfc2401.txt

  4.1 Definition and Scope    A Security Association (SA) is a simplex "connection" that affords    security services to the traffic carried by it.  Security services    are afforded to an SA by the use of AH, or ESP, but not both.  If    both AH and ESP protection is applied to a traffic stream, then two    (or more) SAs are created to afford protection to the traffic stream.    To secure typical, bi-directional communication between two hosts, or    between two security gateways, two Security Associations (one in each    direction) are required.    A security association is uniquely identified by a triple consisting    of a Security Parameter Index (SPI), an IP Destination Address, and a    security protocol (AH or ESP) identifier.  In principle, the    Destination Address may be a unicast address, an IP broadcast    address, or a multicast group address.  However, IPsec SA management    mechanisms currently are defined only for unicast SAs.

  The only possible mechanism is to use the GRE over IPSec.

  I hope this helps.

  Kind regards
  Abhishek Purohit
  CCIE-S-35269

• Road by default from version 6.3 PIX IPsec tunnel

  We have a PIX 501 running IOS version 6.3.1.

  There are currently 3 tunnels IPsec active as described below.

  What we would like is to have all traffic by default (0.0.0.0 0.0.0.0) range out through the tunnel of the middle line so that traffic can be protected by a firewall on the other side of the tunnel.  Since ICF is a Sonicwall what would be needed to be changed in the configuration on the PIX to get there?

  Thank you

  6.3 (1) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the 86AZXXmRLxfv/oUQ encrypted password

  86AZXXmRLxfv/oUQ encrypted passwd

  Site A hostname

  domain default.int

  clock timezone STD - 7

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  name 75.75.75.2 CovadHub

  name 75.48.25.12 Sonicwall

  access-list 101 permit ip 10.10.5.0 255.255.255.0 10.10.1.0 255.255.255.0

  access-list 101 permit ip 10.10.5.0 255.255.255.0 10.10.2.0 255.255.255.0

  access-list 101 permit ip 10.10.5.0 255.255.255.0 10.10.3.0 255.255.255.0

  access-list 101 permit icmp any any echo response

  access-list 101 permit icmp any any echo

  access-list 102 permit ip 10.10.5.0 255.255.255.0 10.10.2.0 255.255.255.0

  access-list 103 allow ip 10.10.5.0 255.255.255.0 10.10.1.0 255.255.255.0

  access-list 104. allow ip 10.10.5.0 255.255.255.0 10.10.3.0 255.255.255.0

  pager lines 24

  opening of session

  monitor debug logging

  logging warnings put in buffered memory

  ICMP allow 10.10.5.0 255.255.255.0 inside

  Outside 1500 MTU

  Within 1500 MTU

  external IP 75.25.14.2 255.255.255.0

  IP address inside 10.10.5.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 10.10.5.0 255.255.255.0 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  (Inside) NAT 0-list of access 101

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  allow icmp a conduit

  Route outside 0.0.0.0 0.0.0.0 75.25.14.1 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  NTP server 132.163.4.102 source outdoors

  NTP server 129.7.1.66 source outdoors

  Enable http server

  http 10.10.1.0 255.255.255.0 inside

  http 10.10.5.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp - esp-md5-hmac pix11

  peer11 card crypto ipsec-isakmp 10

  correspondence address 10 card crypto peer11 102

  peer11 card crypto 10 peers set 75.95.21.41

  peer11 card crypto 10 set transform-set pix11

  11 peer11 of ipsec-isakmp crypto map

  correspondence address 11 card crypto peer11 103

  11 peer11 peer Sonicwall crypto card game

  card crypto peer11 11 set transform-set pix11

  12 peer11 of ipsec-isakmp crypto map

  correspondence address 12 card crypto peer11 104

  card crypto peer11 12 set peer 75.62.58.28

  card crypto peer11 12 set transform-set pix11

  peer11 interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 75.62.58.28 netmask 255.255.255.240

  ISAKMP key * address netmask 255.255.255.224 Sonicwall

  ISAKMP key * address 75.95.21.41 netmask 255.255.255.252

  ISAKMP identity address

  ISAKMP keepalive 10

  ISAKMP nat-traversal 20

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  part of pre authentication ISAKMP policy 11

  encryption of ISAKMP policy 11

  ISAKMP policy 11 md5 hash

  11 2 ISAKMP policy group

  ISAKMP duration strategy of life 11 28800

  part of pre authentication ISAKMP policy 12

  encryption of ISAKMP policy 12

  ISAKMP policy 12 md5 hash

  12 2 ISAKMP policy group

  ISAKMP duration strategy of life 12 36000

  Telnet 10.10.5.0 255.255.255.0 inside

  Telnet 0.0.0.0 0.0.0.0 inside

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH 0.0.0.0 0.0.0.0 inside

  SSH timeout 60

  Console timeout 0

  dhcpd address 10.10.5.70 - 10.10.5.101 inside

  dhcpd dns 10.10.1.214

  dhcpd rental 43200

  dhcpd ping_timeout 750

  dhcpd field default.int

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:36d2c26afa8

  03957d 3659

  868d9219f8

  2

  : end

  Hello

  You do not configure really any type of default route for the VPN L2L. You match rather traffic with 'everything' destination on configuring VPN L2L. Basically you would like to configure the VPN L2L ACL encryption with the 'whole' destination map

  I guess in your case it would be the ACL named "103".

  access-list 103 allow ip 10.10.5.0 255.255.255.0 any

  IP 10.10.5.0 doesn't allow any access list 103 255.255.255.0 10.10.1.0 255.255.255.0

  Naturally, your NAT0 ACL configuration should also reflect this change. I guess the end remote Sonicwall'd private NAT to public Internet access in this case whereas. I guess that in this case, the ACL NAT0 might even be just this one rule ACL

  access-list 101 permit ip 10.10.5.0 255.255.255.0 any

  BUT what I was asking however for now mainly is the fact it has a priority of '11' in the 'crypto map' which has between 2 other L2L VPN connections.

  peer11 card crypto ipsec-isakmp 10

  correspondence address 10 card crypto peer11 102

  peer11 card crypto 10 peers set 75.95.21.41

  peer11 card crypto 10 set transform-set pix11

  11 peer11 of ipsec-isakmp crypto map

  correspondence address 11 card crypto peer11 103

  11 peer11 peer Sonicwall crypto card game

  card crypto peer11 11 set transform-set pix11

  12 peer11 of ipsec-isakmp crypto map

  correspondence address 12 card crypto peer11 104

  card crypto peer11 12 set peer 75.62.58.28

  card crypto peer11 12 set transform-set pix11

  If you have changed the destination address of '103' crypto VPN L2L ACL at "" I guess that would probably cause so that the last connection VPN L2L with "12" priority may stop working since the previous connection already corresponds to 'all' your network 'inside' destination address.

  The solution might be to delete the current configuration of the '11' priority and add it with '13' for example, so that the other 2 connections VPN L2L could continue to work and all the rest of the traffic would be passed to the connection VPN L2L with Sonicwall as the remote peer.

  No crypto map ipsec-isakmp 11 peer11

  no correspondence address 11 card crypto peer11 103

  no set of 11 peer11 card crypto don't peer Sonicwall

  No peer11 11 set transform-set pix11 crypto card

  13 peer11 of ipsec-isakmp crypto map

  correspondence address 13 card crypto peer11 103

  13 card crypto peer Sonicwall peer11 game

  card crypto peer11 13 pix11 transform-set game

  I have to say that this is how I expect it should work. I worked with VPN L2L that have been configured in this way but its quite rare.

  If you want to try something like that, of course, be ready to return to the old configuration with your admins of the remote peer, if things do not work. I guess more difficult configurations changes must be made on the remote end while your configuration of the ends should be fairly simple.

  Hope this helps

  -Jouni

• No Internet VPN IPsec Tunnel access

  I use the Netgear VPN - Pro 5.51.001 client to configure and run a VPN Tunnel to a UTM10 (3.5.2 - 14). It works very well so far and my private network resources could be achieved.

  When the tunnel is established, the client (W7 x 64) loses connectivity to the Internet on LAN or WLAN port desired and expected.
  Now, the Internet connection must be provided inside my private behind the UTM network.
  Due to a DNS SERVER running on my private network addresses (even on the internet) are correctly resolved (use NSLOOKUP to check), but cannot be routed to my VPN client.
  I found, that the map virtual Green-bow had no entry for the gateway, but the entry door (my UTM10) could be ping from the VPN client.
  After you enter the internal IP address of the UTM in the field of "Redundant GW" of the client software and restart and reconnect to the customer,
  the entry door is now displayed in the properties of Green-bow (ipconfig on CMD-screen), but still no internet site can be reached.

  To test, I have disabled the firewall on my client PC.
  The tunnel use mode-config and receives the entries in DNS and WINS server according to the config folder. The client is configured to force the NAT-traversal.

  Customers should be able to connect from the offices at home (or mobile) to the network/domain of society and use internet as if they were connected locally.
  SSL - VPN is not an option.

  m.Vogel wrote:
  Now, the Internet connection must be provided inside my private behind the UTM network.

  No, it doesn't work like that. If you want to "full-tunnel" support you need to stick with SSL VPN and select this option in the settings.

• VPN from Site to Site RV325 to RV180 connection problems

  Hi all

  I am new to VPN and networking, please be patient with me.

  I recently bought a RV325 and a RV180 to create a site to site VPN Ipsec tunnel. I was not able to establish a connection between the two. I don't know that this is a setting that I have hurt or something on my part. I would be extremely grateful to anyone who can help me with this!

  I've attached screenshots of the two router... As I'm not sure what you guys would like to see.  If there is no specific details please ask and I'll give you.

  Thank you very much!

  Hello and thank you for the detailed information.

  I checked the configuration on both routers and found a few issues:

  First and the most important is the fact that on the two router WAN PII addresses use private IP by far. On the RV180W you 192.168.1.33 and you use on the 192.168.0.104 RV325.

  It's a big problem because it's showing that you're behind another router, which is the device that made the public IP address that you are trying to connect.

  To resolve this problem, you must call the ISP on both ends and ask them to change the modem in Bridge mode, that way the real public IP address will be assigned to the WAN 1 port on routers and you will be able to connect.

  The second problem I found is that, on the side of RV325, your LAN and WAN IP addresses are on the same subnet 192.168.0.x. Now, this problem will be solved once the modem is changed to the bridge, so nothing to change mode.

  Finally, I noticed that on the VPN configuration you use the 192.168.1.0 as the subnet for the RV180W, when, according to your screenshots, the actual LAN of the RV180W subnet is 192.168.2.1.

  One last thing is that I will recommend to disable the aggressive mode on each side of the VPN as opposed to have it turned on on both sides.

  I hope this helps!

• IPSec Tunnel site to Site between ASA (static IP) to the firewall Microtick (dynamic IP) cannot telnet routeros and open https

  I purchased Mikrotik hardware devices and want to use routeros seat firewall cisco asa establish VPN. Aims to establish that a branch may be two IPSEC VPN access devices at the headquarters of the server via the public network.

  But now, I'm having some trouble, so I have cisco asa branches and headquarters to establish successful ipsec vpn.
  (1) branch routeros WAN port using a private IP address and is a member of the asa above outdoor sound created vpn ipsec, vpn successfully established internal servers and I ping the switch at the headquarters of the branch. However, there is a problem, I go through routeros visit that the headquarters of the https server pages can not be opened, telnet internal switches can telnet to the top, but were unable to penetrate into the character.
  (2) in addition, I left the branch routeros on a public IP address WAN port and asa VPN IPSEC created seat, said problems above are not, the server can also be accessed, telnet switch can also enter text and control.
  At the present time, I have encountered this problem of interface not CAN not because I need to create of very, very many industries and the need to establish headquarters communications branch offices so I have to use private IP addresses to access the Wan, unable to do wan are public IP address and headquarters to establish IPSEC VPN.

  now, I can't telnet asa inside the cisco router and open the web inside https, I can't solve the problems.

  now, registrants of asa:

  interface GigabitEthernet0/0
  nameif outside
  security-level 0
  IP 49.239.3.10 255.255.255.0
  !
  interface GigabitEthernet0/1
  nameif inside
  security-level 100
  IP 172.17.0.111 255.255.255.0

  network of the object inside
  172.17.1.0 subnet 255.255.255.0
  network outsidevpn object
  Subnet 192.168.0.0 255.255.0.0

  QQQ

  NAT (inside, outside) static source inside inside destination static outsidevpn outsidevpn non-proxy-arp-search to itinerary

  Route outside 0.0.0.0 0.0.0.0 49.239.3.1 1
  Route inside 172.17.1.0 255.255.255.0 172.17.0.5 1

  Crypto ipsec transform-set esp-3des esp-md5-hmac ikev1 cisco
  Crypto ipsec pmtu aging infinite - the security association
  Crypto dynamic-map cisco 1000 set pfs
  Crypto dynamic-map cisco 1000 set transform-set cisco ikev1
  Crypto dynamic-map cisco 1000 value reverse-road
  Cisco-cisco ipsec isakmp dynamic 1000 card crypto
  cisco interface card crypto outside
  trustpool crypto ca policy
  Crypto isakmp nat-traversal 60
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  IPSec-attributes tunnel-group DefaultL2LGroup
  IKEv1 pre-shared-key *.

  Hello

  Could you share the output of the counterpart of its IPSec cry see the 49.239.3.10 of the other device?

  Kind regards

  Aditya

• EIGRP via IPSec site to site VPN

  having trouble getting to work through an IOS EIGRP (2ea. 2811 s) connection of the site to site VPN IPSec peer.  IPSec VPN works with route directions static tunnel.  By using the IPSec policy basis and VTI interface:

  crypto ISAKMP policy 1

  preshared authentication

  Group 2

  ISAKMP crypto key "" address 192.168.x.66

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac vpn

  Crypto ipsec df - game

  !

  static-crypt 6 map ipsec-isakmp crypto

  the value of 192.168.x.66 peer

  Set transform-set vpn

  match address 101

  !

  tunnel1 interface

  IP address 1xx.33.20.226 255.255.255.252

  no ip redirection

  IP 1400 MTU

  IP tcp adjust-mss 1360

  QoS before filing

  source of tunnel FastEthernet 0/0

  destination 192.168.x.66 tunnel

  crypto static crypto map

  !

  interface FastEthernet 0/0

  Add an IP...

  crypto static crypto map

  !

  Router eigrp 10

  passive-interface default

  no passive-interface FastEthernet 0/1

  no passive-interface Tunnel1

  network...

  network...

  No Auto-resume

  !

  IP route 0.0.0.0 0.0.0.0 Tunnel1

  IP route 0.0.0.0 0.0.0.0 146.33.20.225<-- peer's="" default-gateway="" is="" vpn="" peer="" router="" on="" other="" side="" of="" satelite="">

  must be something simple, but I can't.

  Thank you, kevin

  Unfamiliar with the VTI, but I think you are missing:

  ipv4 ipsec tunnel mode

  Profile of tunnel ipsec protection

  Also don't think that you need crypto card in the tunnel because it is already on fa0/0.  What looks like the access-list 101? Take a look at this doc:

  http://www.ciscosystems.com/en/us/docs/iOS/12_3t/12_3t14/feature/guide/gtIPSctm.html

• remote VPN and vpn site to site vpn remote users unable to access the local network

  As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

  The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

  ASA Version 8.2 (2)
  !
  host name
  domain kunchevrolet
  activate r8xwsBuKsSP7kABz encrypted password
  r8xwsBuKsSP7kABz encrypted passwd
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  PPPoE client vpdn group dataone
  IP address pppoe
  !
  interface Ethernet0/1
  nameif inside
  security-level 50
  IP 192.168.215.2 255.255.255.0
  !
  interface Ethernet0/2
  nameif Internet
  security-level 0
  IP address dhcp setroute
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  management only
  !
  passive FTP mode
  clock timezone IST 5 30
  DNS server-group DefaultDNS
  domain kunchevrolet
  permit same-security-traffic intra-interface
  object-group network GM-DC-VPN-Gateway
  object-group, net-LAN
  access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 Internet
  IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  enable ASDM history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  AAA authentication enable LOCAL console
  LOCAL AAA authentication serial console
  Enable http server
  x.x.x.x 255.255.255.252 out http
  http 192.168.215.0 255.255.255.252 inside
  http 192.168.215.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic dynmap 65500 transform-set RIGHT
  card crypto 10 VPN ipsec-isakmp dynamic dynmap
  card crypto VPN outside interface
  card crypto 10 ASA-01 set peer 221.135.138.130
  card crypto 10 ASA - 01 the transform-set RIGHT value
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  the Encryption
  sha hash
  Group 2
  lifetime 28800
  Telnet 192.168.215.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  management-access inside
  VPDN group dataone request dialout pppoe
  VPDN group dataone localname bb4027654187_scdrid
  VPDN group dataone ppp authentication chap
  VPDN username bb4027654187_scdrid password * local store
  interface for identifying DHCP-client Internet customer
  dhcpd dns 218.248.255.141 218.248.245.1
  !
  dhcpd address 192.168.215.11 - 192.168.215.254 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Des-sha1 encryption SSL
  WebVPN
  allow outside
  tunnel-group-list activate
  internal kun group policy
  kun group policy attributes
  VPN - connections 8
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  kunchevrolet value by default-field
  test P4ttSyrm33SV8TYp encrypted password username
  username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
  username kunauto attributes
  Strategy Group-VPN-kun
  Protocol-tunnel-VPN IPSec
  tunnel-group vpngroup type remote access
  tunnel-group vpngroup General attributes
  address pool VPN_Users
  Group Policy - by default-kun
  tunnel-group vpngroup webvpn-attributes
  the vpngroup group alias activation
  vpngroup group tunnel ipsec-attributes
  pre-shared key *.
  type tunnel-group test remote access
  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  Review the ip options
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
  : end
  kunauto #.

  Hello

  Looking at the configuration, there is an access list this nat exemption: -.

  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

  But it is not applied in the States of nat.

  Send the following command to the nat exemption to apply: -.

  NAT (inside) 0 access-list sheep

  Kind regards

  Dinesh Moudgil

  P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community