No Internet VPN IPsec Tunnel access

I use the Netgear VPN - Pro 5.51.001 client to configure and run a VPN Tunnel to a UTM10 (3.5.2 - 14). It works very well so far and my private network resources could be achieved.

When the tunnel is established, the client (W7 x 64) loses connectivity to the Internet on LAN or WLAN port desired and expected.
Now, the Internet connection must be provided inside my private behind the UTM network.
Due to a DNS SERVER running on my private network addresses (even on the internet) are correctly resolved (use NSLOOKUP to check), but cannot be routed to my VPN client.
I found, that the map virtual Green-bow had no entry for the gateway, but the entry door (my UTM10) could be ping from the VPN client.
After you enter the internal IP address of the UTM in the field of "Redundant GW" of the client software and restart and reconnect to the customer,
the entry door is now displayed in the properties of Green-bow (ipconfig on CMD-screen), but still no internet site can be reached.

To test, I have disabled the firewall on my client PC.
The tunnel use mode-config and receives the entries in DNS and WINS server according to the config folder. The client is configured to force the NAT-traversal.

Customers should be able to connect from the offices at home (or mobile) to the network/domain of society and use internet as if they were connected locally.
SSL - VPN is not an option.

m.Vogel wrote:

Now, the Internet connection must be provided inside my private behind the UTM network.

m.Vogel wrote:
Now, the Internet connection must be provided inside my private behind the UTM network.

No, it doesn't work like that. If you want to "full-tunnel" support you need to stick with SSL VPN and select this option in the settings.

Tags: Netgear

Similar Questions

ASA ASA from Site to Site VPN IPSec Tunnel

Any help would be greatly appreciated...

I have two devices Cisco ASA with a Site for the configuration of the tunnel VPN IPSec Site as follows: -.

Site #1 - Cisco ASA running version 8.2 (1) with an internal range of 10.0.0.x/24

Site #2 - Cisco ASA running version 8.2 (1) with an internal range of 10.1.1.x/24

Site #1 is simple and has a dynamic NAT rule which translates all of the inside and the outside (public IP) of the SAA.

Internet access works very well in all workstations of this site. A static route is configured to redirect all traffic to a public router upstream.

Site #2 is slightly more complicated; the Cisco ASA is configured with 10.1.1.254/24 as its interior IP address and 10.1.2.254/24 as its external IP address. A dynamic NAT rule is configured to translate everything inside as the 10.1.2.254 (outside) address of the ASA. A default static route is then configured to redirect all traffic to a Draytek device on 10.1.2.253. This device then performs its own private Public NAT. Again the Internet works fine all hosts inside the Cisco ASA (10.1.1.x)

The IPSec tunnel is created with the networks local and remote endpoint as above (10.0.0.x/24) and (10.1.1.x/24). The Draytek at the Site #2 device is configured with a form of DMZ that allows essentially ALL traffic toward the front directly on the external interface of the ASA (10.1.2.254). The Phase 1 and Phase 2 negotiation of the tunnel ends correctly, and the tunnel is formed without any problem. However, all traffic passing on networks ICMP does not end and the Syslog reports the following-

Site #1-

6 January 19, 2011 15:27:21 302020 ZEFF-SB-01_LAN 1 10.1.1.51 0 Built of outbound ICMP connection for faddr 10.1.1.51/0 gaddr ZEFF-SB-01_LAN/1 laddr ZEFF-SB-01_LAN/1

6 January 19, 2011 15:27:23 302021 10.1.1.51 0 ZEFF-SB-01_LAN 1 Connection of ICMP disassembly for faddr 10.1.1.51/0 gaddr ZEFF-SB-01_LAN/1 laddr ZEFF-SB-01_LAN/1

Site #2-

6 January 19, 2011 15:24:47 302020 10.1.1.51 0 10.0.0.30 1 Built of outbound ICMP connection for faddr gaddr laddr 10.1.1.51/0 10.1.1.51/0 10.0.0.30/1

6 January 19, 2011 15:24:49 302021 10.0.0.30 1 10.1.1.51 0 Connection of disassembly for faddr gaddr laddr 10.1.1.51/0 10.1.1.51/0 10.0.0.30/1 ICMP

It's the same for any form of traffic passing over the tunnel. The ACL is configured to allow segments of LAN out to any destination. At this point, I left scratching my head, as my original theory was to blame the Draytek, but after reading the documentation given to the DMZ host configuration, it appears this parameter is configured all traffic is simply forwarded to the IP address (in this case, the Cisco ASA interface outside).

Anyone can shed light on a possible cause of this problem?

Thank you

Nick

did you bypass the vpn traffic between 10.0.0 and 10.1.1 to be NAT - ed on the two ASA?

Please provide the following information

-set up the tunnel

-show the isa cry his

-show the ipsec cry his

-ping of the site 1 site 2 via tunnel

-capture "crypto ipsec to show his" once again

-ping from site 2 to 1 by the tunnel of the site

-capture "crypto ipsec to show his" once again

-two ASA configuration.

ASA: VPN IPSEC Tunnel from 5505(ver=8.47) to 5512 (ver = 9.23)

Hi-

We have connected tunnel / VPN configuration between an ASA 5505 - worm = 8.4 (7) and 5512 - worm = 9.2 (3).
We can only ping in a sense - 5505 to the 5512, but not of vice-versa(5512 to 5505).

Networks:

Local: 192.168.1.0 (answering machine)
Distance: 192.168.54.0 (initiator)

See details below on our config:

SH run card cry

card crypto outside_map 2 match address outside_cryptomap_ibfw
card crypto outside_map 2 pfs set group5
outside_map 2 peer XX crypto card game. XX.XXX.XXX
card crypto outside_map 2 set transform-set ESP-AES-256-SHA ikev1
crypto map outside_map 2 set ikev2 AES256 ipsec-proposal

outside_map interface card crypto outside

Note:
Getting to hit numbers below on rules/ACL...

SH-access list. I have 54.0

permit for access list 6 outside_access_out line scope ip 192.168.1.0 255.255.255.0 192.168.54.0 255.255.255.0 (hitcnt = 15931) 0x01aecbcc
permit for access list 1 outside_cryptomap_ibfw line extended ip object NETWORK_OBJ_192.168.1.0_24 object NETWORK_OBJ_192.168.54.0_24 (hitcnt = 3) 0xa75f0671
access-list 1 permit line outside_cryptomap_ibfw extended ip 192.168.1.0 255.255.255.0 192.168.54.0 255.255.255.0 (hitcnt = 3) 0xa75f0671

SH run | I have access-group
Access-group outside_access_out outside interface

NOTE:
WE have another working on the 5512 - VPN tunnel we use IKE peer #2 below (in BOLD)...

HS cry his ikev1

IKEv1 SAs:

HIS active: 2
Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
Total SA IKE: 2

1 peer IKE: XX. XX.XXX.XXX
Type: L2L role: answering machine
Generate a new key: no State: MM_ACTIVE
2 IKE peers: XXX.XXX.XXX.XXX
Type: L2L role: answering machine
Generate a new key: no State: MM_ACTIVE

SH run tunnel-group XX. XX.XXX.XXX
tunnel-group XX. XX.XXX.XXX type ipsec-l2l
tunnel-group XX. XX.XXX.XXX General-attributes
Group - default policy - GroupPolicy_XX.XXX.XXX.XXX
tunnel-group XX. XX.XXX.XXX ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.

SH run | I have political ikev1

ikev1 160 crypto policy
preshared authentication
aes-256 encryption
Group 5
life 86400

SH run | I Dynamics
NAT interface dynamic obj - 0.0.0.0 source (indoor, outdoor)
NAT source auto after (indoor, outdoor) dynamic one interface

NOTE:
To from 5512 at 5505-, we can ping a host on the remote network of ASA local

# ping inside the 192.168.54.20
Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 192.168.54.20, wait time is 2 seconds:
!!!!!
Success rate is 100 per cent (5/5), round-trip min/avg/max = 30/32/40 ms

Determination of 192.168.1.79 - local host route to 192.168.54.20 - remote host - derivation tunnel?

The IPSEC tunnel check - seems OK?

SH crypto ipsec his
Interface: outside
Tag crypto map: outside_map, seq num: 2, local addr: XX.XXX.XXX.XXX

outside_cryptomap_ibfw to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.54.0 255.255.255.0
local ident (addr, mask, prot, port): (192.168.1.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.54.0/255.255.255.0/0/0)
current_peer: XX. XX.XXX.XXX

#pkts program: 4609, #pkts encrypt: 4609, #pkts digest: 4609
#pkts decaps: 3851, #pkts decrypt: 3851, #pkts check: 3851
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 4609, model of #pkts failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#TFC rcvd: 0, #TFC sent: 0
#Valid errors ICMP rcvd: 0, #Invalid ICMP errors received: 0
#send errors: 0, #recv errors: 0

local crypto endpt. : XX.XXX.XXX.XXX/0, remote Start crypto. : XX. XX.XXX.XXX/0
Path mtu 1500, ipsec 74 (44) generals, media, mtu 1500
PMTU time remaining: 0, political of DF: copy / df
Validation of ICMP error: disabled, TFC packets: disabled
current outbound SPI: CDC99C9F
current inbound SPI: 06821CBB

SAS of the esp on arrival:
SPI: 0x06821CBB (109190331)
transform: aes-256-esp esp-sha-hmac no compression
running parameters = {L2L, Tunnel, group 5 PFS, IKEv1}
slot: 0, id_conn: 339968, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (3914789/25743)
Size IV: 16 bytes
support for replay detection: Y
Anti-replay bitmap:
0xFFFFFFFF to 0xFFFFFFFF
outgoing esp sas:
SPI: 0xCDC99C9F (3452542111)
transform: aes-256-esp esp-sha-hmac no compression
running parameters = {L2L, Tunnel, group 5 PFS, IKEv1}
slot: 0, id_conn: 339968, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (3913553/25743)
Size IV: 16 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001

--> The local ASA 5512 - where we have questions - tried Packet Tracer... seems we receive requests/responses...

SH cap CAP

34 packets captured

1: 16:41:08.120477 192.168.1.79 > 192.168.54.20: icmp: echo request
2: 16:41:08.278138 192.168.54.20 > 192.168.1.79: icmp: echo request
3: 16:41:08.278427 192.168.1.79 > 192.168.54.20: icmp: echo reply
4: 16:41:09.291992 192.168.54.20 > 192.168.1.79: icmp: echo request
5: 16:41:09.292282 192.168.1.79 > 192.168.54.20: icmp: echo reply

--> On the ASA 5505 distance - we can ping through the 5512 to the local host (192.168.1.79)

SH cap A2

42 packets captured

1: 16:56:16.136559 802. 1 q vlan P0 192.168.54.20 #1 > 192.168.1.79: icmp: echo request
2: 16:56:16.168860 802. 1 q vlan P0 192.168.1.79 #1 > 192.168.54.20: icmp: echo reply
3: 16:56:17.140434 802. 1 q vlan P0 192.168.54.20 #1 > 192.168.1.79: icmp: echo request
4: 16:56:17.171652 802. 1 q vlan P0 192.168.1.79 #1 > 192.168.54.20: icmp: echo reply
5: 16:56:18.154426 802. 1 q vlan P0 192.168.54.20 #1 > 192.168.1.79: icmp: echo request
6: 16:56:18.186178 802. 1 q vlan P0 192.168.1.79 #1 > 192.168.54.20: icmp: echo reply
7: 16:56:19.168417 802. 1 q vlan P0 192.168.54.20 #1 > 192.168.1.79: icmp: echo request

--> Package trace on 5512 does no problem... but we cannot ping from host to host?

entry Packet-trace within the icmp 192.168.1.79 8 0 detailed 192.168.54.20

Phase: 4
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
class-map default class
match any
Policy-map global_policy
class class by default
Decrement-ttl connection set
global service-policy global_policy
Additional information:
Direct flow from returns search rule:
ID = 0x7fffa2d0ba90, priority = 7, area = conn-set, deny = false
hits = 4417526, user_data = 0x7fffa2d09040, cs_id = 0 x 0, use_real_addr, flags = 0 x 0 = 0 protocol
IP/ID=0.0.0.0 SRC, mask = 0.0.0.0, port = 0, = 0 tag
IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, tag = 0, dscp = 0 x 0
input_ifc = output_ifc = any to inside,

Phase: 5
Type: NAT
Subtype:
Result: ALLOW
Config:
NAT interface dynamic obj - 0.0.0.0 source (indoor, outdoor)
Additional information:
Definition of dynamic 192.168.1.79/0 to XX.XXX.XXX.XXX/43904
Direct flow from returns search rule:
ID = 0x7fffa222d130, priority = 6, area = nat, deny = false
hits = 4341877, user_data = 0x7fffa222b970, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol
IP/ID=0.0.0.0 SRC, mask = 0.0.0.0, port = 0, = 0 tag
IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, tag = 0, dscp = 0 x 0
input_ifc = inside, outside = output_ifc

...

Phase: 14
Type: CREATING STREAMS
Subtype:
Result: ALLOW
Config:
Additional information:
New workflow created with the 7422689 id, package sent to the next module
Information module for forward flow...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_inspect_icmp
snp_fp_translate
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat

Information for reverse flow...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_translate
snp_fp_inspect_icmp
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat

Result:
input interface: inside
entry status: to the top
entry-line-status: to the top
output interface: outside
the status of the output: to the top
output-line-status: to the top
Action: allow

--> On remote ASA 5505 - Packet track is good and we can ping remote host very well... dunno why he "of Nations United-NAT?

Destination - initiator:

entry Packet-trace within the icmp 192.168.54.20 8 0 detailed 192.168.1.79

...
Phase: 4
Type: UN - NAT
Subtype: static
Result: ALLOW
Config:
NAT (inside, outside) static source NETWORK_OBJ_192.168.54.0_24 NETWORK_OBJ_192.168.54.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
Additional information:
NAT divert on exit to the outside interface
Untranslate 192.168.1.79/0 to 192.168.1.79/0
...

Summary:
We "don't" ping from a host (192,168.1.79) on 5512 - within the network of the 5505 - inside the network host (192.168.54.20).
But we can ping the 5505 - inside the network host (192.168.54.20) 5512 - inside the network host (192.168.1.79).

Please let us know what other details we can provide to help solve, thanks for any help in advance.

-SP

Well, I think it is a NAT ordering the issue.

Basically as static and this NAT rule-

NAT interface dynamic obj - 0.0.0.0 source (indoor, outdoor)

are both in article 1 and in this article, it is done on the order of the rules so it does match the dynamic NAT rule rather than static because that seems to be higher in the order.

To check just run a 'sh nat"and this will show you what order everthing is in.

The ASA is working its way through the sections.

You also have this-

NAT source auto after (indoor, outdoor) dynamic one interface

which does the same thing as first statement but is in section 3, it is never used.

If you do one of two things-

(1) configure the static NAT statement is above the dynamic NAT in section 1 that is to say. You can specify the command line

or

(2) remove the dynamic NAT of section 1 and then your ASA will use the entry in section 3.

There is a very good document on this site for NAT and it is recommended to use section 3 for your general purpose NAT dynamic due precisely these questions.

It is interesting on your ASA 5505 you duplicated your instructions of dynamic NAT again but this time with article 2 and the instructions in section 3 that is why your static NAT works because he's put in correspondence before all your dynamic rules.

The only thing I'm not sure of is you remove the dynamic NAT statement in article 1 and rely on the statement in section 3, if she tears the current connections (sorry can't remember).

Then you can simply try to rearrange so your static NAT is above it just to see if it works.

Just in case you want to see the document here is the link-

https://supportforums.Cisco.com/document/132066/ASA-NAT-83-NAT-operation-and-configuration-format-CLI

Jon

VPN - IPSec remote access

Hi community support.

I have an ASA with double tis (gig0/0-gig0/1) and gig0/1 has a default route with admin distance from 254 to back it up.

I just created Cisco Anyconnect on the SAA the wizard and I can connect to both interfaces.

IPSec tunnel configuration is also there and I tried to create an IPSec VPN entry on the with my iPhone and I can connect to gig0/0 or gig0/1 if gig0/0 is stopped. But I can not connect to gig0/1 if gig0/0 is in place.

When I run ' isa crypto to show his ", I get the following error:

ciscoasa # show crypto isa his

IKEv1 SAs:

ITS enabled: 1
Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
Total SA IKE: 1

1 peer IKE: X.X.X.X
Type: user role: answering machine
Generate a new key: no State: AM_WAIT_MSG3

So the question is, is that what it means and why it works if I close gig0/0 (which is the main interface) and would be why Cisco Anyconnect works also with two interfaces up and customer VPN Cisco Legacy does not work?

Thank you

Hello

What is expected due to the way table routing of the SAA is currently designed. ASA supports not only routing table overall but the routing by interface table as well.

In the case of IPSec VPN, ASA-control path will do a search of route for the response packet. This search returns the interface of ISP outside/primaries as the best route, but because you tried to connect to the backup, ASA will drop the packet.

In the case of Anyconnect VPN or SSH/Telnet, ASA creates a connection to flow forward and reversed to the original application flow and does not pass through the route search mechanism and uses only the output interface (where the request has been received) to send the response. AnyConnect session will follow the routing of each interface table.

Check it for your reference: -.
https://BST.cloudapps.Cisco.com/bugsearch/bug/CSCsg39338/?reffering_site=dumpcr

Kind regards
Dinesh Moudgil

PS Please rate helpful messages.

No Internet for complete Tunnel access

We have an ASA 5550, ver 8.0 (5) and using IPSEC client for remote access in the main office. Remote access works very well with Tunnel from Split. We can access the resources network and go on the internet with Tunnel from Split. However, we can only access network resources, but not for complete tunnel internet access. Do you have any suggestions?

Thank you.

Diane

Diane,

You will need to nat of your pool RA VPN network using your interface global nat ID 1.

For complete tunnel, add two other statements

permit same-security-traffic intra-interface

NAT (outside) 1

http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

Concerning

Blocks VIRTUAL local network access to a tunnel VPN IPSec on WRV200?

I have two identical WRV200 wireless routers which are connected by a VPN IPSec tunnel. This goes to my LAN LAN of my parents. Everything works well.

But I also have my WRV200 configured for two VLANS. Vlan1 for my network and secure wireless access. VLAN2 for a WiFi not secure for customers.

My problem is that my guest on VLAN2 slips through the VPN devices and access on LAN of my parents. I'm looking for a way to block to do this.

I use the version of the software on the two routers (v1.0.39).

For what it's worth, I know that my receive an IP address in the range 192.168.x.101 DHCP - 199. I could assign a different range if that helps. I thought that I could block this beach on the remote router firewall, but I see there is blocking a single IP address at the time, maximum of 8. Am I missing something?

Or could I put something weird in the routing tables somewhere to get the IPs guest out of lala land?

Any suggestions are appreciated. I can't be the only one in this boat.

Steve

Try to check local and remote, vpn under safe group settings if you change the ip address range subnet. Don't include the range of ip addresses of the computers wireless comments so that it will not pass through the vpn tunnel. If there is no ip range option, you must to the subnet of the network in order to control the ip address you want to allow on the vpn tunnel.

How can I bypass ipsec tunnel when do ftp?

Hello

I would like to make an IPsec VPN tunnel between my breanch and Headquarters Office (VPN router). I do FTP specific ip on the Internet without IPsec tunnel. This should be happenning on my website. then when users try to ftp://125.7.123.46 it should work around the tunnel and connect directly?

Can any one give me a heads up how do I do this on my router?

Thanks in advance,

Reza

Reza,

In order to achieve this the 192.168.10.0/24 network server, here's what you need:

##########################################

access-list 150 deny ip 192.168.10.0 0.0.0.255 192.168.2.0 0.0.0.255

access-list 150 permit ip 192.168.10.0 0.0.0.255 any

overload of IP nat inside source list 150 interface Dialer0

interface Ethernet0

IP nat inside

interface Dialer0

NAT outside IP

#########################################

With the above configuration you have access to Internet in the 192.168.10.0/24 network without disturbing the IPsec traffic.

You have this double threat?

Federico.

How to configure ASA5520 of Checkpoint IPsec tunnel configuration

Hi guys and under tension, a lot of it!

I have a problem, I set up an IPsec tunnel between my ASA5520 at a Checkpoint Firewall (PE) CONFIG below (not true FT)

network of the ASA_MAPPED object

4.4.4.0 subnet 255.255.255.0

network of the CHECKPOINT_MAPPED object

5.5.5.5.0 SUBNET 255.255.255.0

OUT_CRYPTO extended access list permit ip object ASA_MAPPED object CHECKPOINT_MAPPED

Crypto ipsec transform-set ikev1 CHECKPOINT_SET aes - esp esp-sha-hmac

destination NAT (INSIDE, OUTSIDE) static source ALLNETWORKS(10.0.0.0/16) ASA_MAPPED CHECKPOINT_MAPPED of CHECKPOINT_MAPPED static

NAT (INSIDE, OUTSIDE) source of destination ALLNETWORKS(10.0.0.0/16) static ASA_MAPPED static 4.4.4.11 5.5.5.11

card crypto OUTSIDE_MAP 5 corresponds to the address OUT_CRYPTO

OUTSIDE_MAP 5 set crypto map peer X.X.X.X

card crypto OUTSIDE_MAP 5 set transform-set CHECKPOINT_SET ikev1

card crypto OUTSIDE_MAP 5 defined security-association life seconds 3600

CHECKPOINT_MAP interface card crypto OUTSIDE

tunnel-group X.X.X.X type ipsec-l2l

tunnel-group ipsec-attributes X.X.X.X

IKEv1 pre-shared-key 1234

ISAKMP crypto 10 nat-traversal

Crypto ikev1 allow outside

IKEv1 crypto policy 10

preshared authentication

aes encryption

sha hash

Group 5

life 86400

IPsec Tunnel is in place and I can access the server on the other side via the beach of NATTED, for example a server behind the checkpoint with the IP 10.90.55.11 is accessible behind the ASA as 4.4.4.11, the problem is that I have never worked on a Checkpoint Firewall and servers/Server 4.4.4.11 that I can't connect to my environment to that checkpoint is configured with a Tunnel interface that is also supposed to to make NAT because of the superimposition of networks, at one point, I added an access to an entire list and bidirectional routing has been reached, but I encountered a new problem, I could not overlook from my servers public became unaccessecable, since all traffic was encrypted and get dropped to VPN: ipsec-tunnel-flow... for now the Tunnel is up and I can access the server via NAT 4.4.4.11, but can't access my internal servers. What did I DO WRONG (also, I don't have access to the Checkpoint Firewall (PE)) how their installation would be or how it should be to allow bidirectional routing?

========================================================

Tag crypto map: CHECKPOINT_MAP, seq num: 5, local addr: X.X.X.X

Access extensive list ip 4.4.4.0 OUT_5_CRYPTO allow 255.255.255.0 5.5.5.0 255.255.255.0

local ident (addr, mask, prot, port): (4.4.4.0/255.255.255.0/0/0)

Remote ident (addr, mask, prot, port): (5.5.5.0/255.255.255.0/0/0)

current_peer: X.X.X.X

#pkts program: 3207, #pkts encrypt: 3207, #pkts digest: 3207

#pkts decaps: 3417, #pkts decrypt: 3417, #pkts check: 3417

compressed #pkts: 0, unzipped #pkts: 0

#pkts uncompressed: 3207, model of #pkts failed: 0, #pkts Dang failed: 0

success #frag before: 0, failures before #frag: 0, #fragments created: 0

Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

#send errors: 0, #recv errors: 0

local crypto endpt. : X.X.X.X/0, remote Start crypto. : X.X.X.X/0

Path mtu 1500, fresh ipsec generals 74, media, mtu 1500

current outbound SPI: 5254EDC6

current inbound SPI: 36DAB960

SAS of the esp on arrival:

SPI: 0x36DAB960 (920303968)

transform: aes - esp esp-sha-hmac no compression

running parameters = {L2L, Tunnel}

slot: 0, id_conn: 19099648, crypto-card: CHECKPOINT_MAP

calendar of his: service life remaining (KB/s) key: (3914999/3537)

Size IV: 16 bytes

support for replay detection: Y

Anti-replay bitmap:

0 x 00000000 0x0000000F

outgoing esp sas:

SPI: 0x5254EDC6 (1381297606)

transform: aes - esp esp-sha-hmac no compression

running parameters = {L2L, Tunnel}

slot: 0, id_conn: 19099648, crypto-card: CHECKPOINT_MAP

calendar of his: service life remaining (KB/s) key: (3914999/3537)

Size IV: 16 bytes

support for replay detection: Y

Anti-replay bitmap:

0x00000000 0x00000001
```
unless I include any any on my access-list and the problem with that is  that my Public servers then get encrypted from the OUTSIDE interface  unless you know of a way to bypass the VPN
```
No, u certainly shouldn't allow 0.0.0.0 for proxy ACL. Again, your config is very good. In addition, package account, this show that traffic is going throug the tunnel in two ways:

#pkts program: 3207

#pkts decaps: 3417

Also, looking at the meter, I can guess that some of the traffic comes from the other site, but does not return back (maybe that's where you can not connect from behing Checkpoint). If you say that 0.0.0.0 solved the problem, are there no other NAT rules for subnet behind ASA, so the server IP, for which you are trying to connect behind the checkpoint, translates into something else (not the beach, included in proxy ACL), when to come back?

IPSec Tunnel permanent between two ASA

Hello

I configured a VPN IPSec tunnel between two ASA 5505 firewall. I want to assure you as the IPSec tunnel (this is why the security association) is permanent and do not drop due to the idle state.

What should I do?

Thanks for any help

Yves

Disables keepalive IKE processing, which is enabled by default.

(config) #tunnel - 10.165.205.222 group ipsec-attributes

KeepAlive (ipsec-tunnel-config) #isakmp disable

Set a maximum time for VPN connections with the command of vpn-session-timeout in group policy configuration mode or username configuration mode:

attributes of hostname (config) #-Group Policy DfltGrpPolicy
hostname (Group Policy-config) #vpn - idle - timeout no

attributes of hostname (config) #-Group Policy DfltGrpPolicy
hostname (Group Policy-config) #vpn - session - timeout no

Thank you

Ajay

IPSec tunnel on router from closure

Is it possible to get a VPN IPSec tunnel on a router from the loopback interface? If so, how?

Hello

Yes it is possible. The command is:

card crypto-address loopback

Please make sure that the loopback interface has a public IP address that is accessible.

http://www.Cisco.com/univercd/CC/TD/doc/product/software/ios124/124tcr/tsec_r/sec_c3ht.htm#wp1274324

HTH,

* Please rate if this helps,

Kind regards

Kamal

ASA 5505 VPN works great but can't access internet via the tunnel to customers

We have an ASA 5505 ASA 8.2.1 running and using IPSec for Remote access clients in the main office. Remote access is a lot of work, with full access to network resources in the main office and the only thing I can't get to work is access to internet through the tunnel. I don't want to use split tunneling. I use ASDM 6.2.1 for configuration. Any help is appreciated. I'm probably missing something simple and it looked so much, I'm probably looking at right beyond the error. Thanks in advance for your time and help! Jim

Add a statement of nat for your segment of customer on the external interface

NAT (outside) - access list

then allow traffic routing back on the same interface, it is entered in the

permit same-security-traffic intra-interface

*

*

* more than information can be found here:

http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807...

On Wednesday, 27 January 2010, at 23:12, jimcanova

Cisco easy VPN access Internet without Split Tunnel

Hey guys

IM wondering if anyone has a config that can help me get access to internet via an easy vpn tunnel on a cisco 877 router.

Basically, we are traveling to be users able to use the internet through vpn, rather than using split tunneling. The reason for this is that we have several sites that are attached by lists of external IP access for some services.

We hope that mobile users to interact with these sites through the central router and use external IP of access routers secure sites.

I hope that makes sense. I know that we can use a proxy but we also use other services of bases no proxy on these sites, it would be rather routed direct access.

Thank you

Luke

Hi Luke,.

Please use the installation of the client VPN (complete tunnel) link below.

http://www.Cisco.com/en/us/prod/collateral/iosswrel/ps6537/ps6586/ps6635/ps6659/prod_white_paper0900aecd80313bd0.PDF

Note the useful message.

Thank you

Kasi

GRE tunnels will not come on VPN IPsec/GRE

Hi all

We have 400 + remote sites that connect to our central location (and a backup site) using Cisco routers with vpn IPSec/GRE tunnels. We use a basic model for the creation of tunnels, so there is very little chance of a bad configuration on each router. Remote sites use Cisco 831 s, central sites use Cisco 2821 s. There is a site where the tunnels WILL refuse just to come.

Routers are able to ping their public IP addresses, so it is not a routing problem, but gre endpoints cannot ping. There is no NATing involved, two routers directly accessing the Internet. The assorded display orders seem to indicate that the SAs are properly built, but newspapers, it seems that last part just don't is finished, and the GRE tunnels come not only upward.

The attached log file, it seems that both its IPSEC & ISAKMP are created @ 00:25:14, then QM_PHASE2 end @ 00:25:15.

00:25:15: ISAKMP: (0:10:HW:2): node error 1891573546 FALSE reason for deletion "(wait) QM.
00:25:15: ISAKMP: (0:10:HW:2): entrance, node 1891573546 = IKE_MESG_FROM_PEER, IKE_QM_EXCH
00:25:15: ISAKMP: (0:10:HW:2): former State = new State IKE_QM_R_QM2 = IKE_QM_PHASE2_COMPLETE
00:25:15: ISAKMP (0:268435467): received 208.XX packet. Dport 500 sport Global 500 (I) QM_IDLE yy.11

00:25:15: IPSEC (key_engine): had an event of the queue with 1 kei messages
00:25:15: IPSEC (key_engine_enable_outbound): rec would prevent ISAKMP
00:25:15: IPSEC (key_engine_enable_outbound): select SA with spinnaker 1572231461/50
00:25:15: ISAKMP: (0:11:HW:2): error in node-1931380074 FALSE reason for deletion "(wait) QM.
00:25:15: ISAKMP: (0:11:HW:2): entrance, node-1931380074 = IKE_MESG_FROM_PEER, IKE_QM_EXCH
00:25:15: ISAKMP: (0:11:HW:2): former State = new State IKE_QM_R_QM2 = IKE_QM_PHASE2_COMPLETE
00:25:15: IPSEC (key_engine): had an event of the queue with 1 kei messages
00:25:15: IPSEC (key_engine_enable_outbound): rec would prevent ISAKMP
00:25:15: IPSEC (key_engine_enable_outbound): select SA with spinnaker 310818168/50

I don't have the remote router log file, and is very long, so I joined her. Before that I captured the log file, I enabled debugging ipsec & isakmp and immediately authorized the SAs.

Assorted useful details and matching orders of show results:

Cisco IOS Software, C831 (C831-K9O3SY6-M), Version 12.4 (25), RELEASE SOFTWARE (fc1)

There are 2 connections of IPSEC/GRE tunnel:

Tunnel101: KC (208.YY. ZZ.11) - remote control (74.WW. XX.35)
Tunnel201: Dallas (208.XX. YY.11) - remote control (74.WW. XX.35)

Site-382-831 #sho ip int br
Interface IP-Address OK? Method State Protocol
FastEthernet1 unassigned YES unset down down
FastEthernet2 unassigned YES unset upward, upward
FastEthernet3 unassigned YES unset upward, upward
FastEthernet4 unassigned YES unset upward, upward
Ethernet0 10.3.82.10 YES NVRAM up up
Ethernet1 74.WW. XX.35 YES NVRAM up up
Ethernet2 172.16.1.10 YES NVRAM up up
Tunnel101 1.3.82.46 YES NVRAM up toward the bottom<>
Tunnel201 1.3.82.62 YES NVRAM up toward the bottom<==== ="">
NVI0 unassigned don't unset upward upwards

Site-382-831 #.
Site-382-831 #sho run int tunnel101
Building configuration...

Current configuration: 277 bytes
!
interface Tunnel101
Description % connected to the 2nd KC BGP 2821 - PRI - B
IP 1.3.82.46 255.255.255.252
IP mtu 1500
IP virtual-reassembly
IP tcp adjust-mss 1360
KeepAlive 3 3
source of tunnel Ethernet1
destination of the 208.YY tunnel. ZZ.11
end

Site-382-831 #.

Site-382-831 #show isakmp crypto his
status of DST CBC State conn-id slot
208.XX. YY.11 74.WW. XX.35 QM_IDLE ASSETS 0 11
208.YY. ZZ.11 74.WW. XX.35 QM_IDLE 10 0 ACTIVE
Site-382-831 #.

Site-382-831 #.
Site-382-831 #show detail of the crypto isakmp
Code: C - IKE configuration mode, D - Dead Peer Detection
NAT-traversal - KeepAlive, N - K
X - IKE extended authentication
PSK - GIPR pre-shared key - RSA signature
renc - RSA encryption

C - id Local Remote I have VRF status BA hash Auth DH lifetime limit.
11 74.WW. XX.35 208.XX. YY.11 ACTIVE 3des sha psk 1 23:56:09
Connection-id: motor-id = 11:2 (hardware)
74.WW 10. XX.35 208.YY. ZZ.11 ACTIVE 3des sha psk 1 23:56:09
Connection-id: motor-id = 10:2 (hardware)
Site-382-831 #.

Site-382-831 #.
Site-382-831 #show crypto ipsec his

Interface: Ethernet1
Tag crypto map: IPVPN_MAP, local addr 74.WW. XX.35

protégé of the vrf: (none)
ident (addr, mask, prot, port) local: (74.WW. XX.35/255.255.255.255/47/0)
Remote ident (addr, mask, prot, port): (208.YY. ZZ.11/255.255.255.255/47/0)
current_peer 208.YY. ZZ.11 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: 2333, #pkts encrypt: 2333, #pkts digest: 2333
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
#send 21, #recv errors 0

local crypto endpt. : 74.WW. XX.35, remote Start crypto. : 208.YY. ZZ.11
Path mtu 1500, mtu 1500 ip, ip mtu IDB Ethernet1
current outbound SPI: 0x45047D1D (1157922077)

SAS of the esp on arrival:
SPI: 0x15B97AEA (364477162)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2004, flow_id: C83X_MBRD:4, crypto card: IPVPN_MAP
calendar of his: service life remaining (k/s) key: (4486831/1056)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE

the arrival ah sas:

SAS of the CFP on arrival:

outgoing esp sas:
SPI: 0x45047D1D (1157922077)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2003, flow_id: C83X_MBRD:3, crypto card: IPVPN_MAP
calendar of his: service life remaining (k/s) key: (4486744/1056)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE

outgoing ah sas:

outgoing CFP sas:

protégé of the vrf: (none)
ident (addr, mask, prot, port) local: (74.WW. XX.35/255.255.255.255/47/0)
Remote ident (addr, mask, prot, port): (208.XX. YY.11/255.255.255.255/47/0)
current_peer 208.XX. YY.11 port 500
LICENCE, flags is {origin_is_acl},
#pkts program: 2333, #pkts encrypt: 2333, #pkts digest: 2333
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
#send 21, #recv errors 0

local crypto endpt. : 74.WW. XX.35, remote Start crypto. : 208.XX. YY.11
Path mtu 1500, mtu 1500 ip, ip mtu IDB Ethernet1
current outbound SPI: 0xE82A86BC (3895101116)

SAS of the esp on arrival:
SPI: 0x539697CA (1402378186)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2008, flow_id: C83X_MBRD:8, crypto card: IPVPN_MAP
calendar of his: service life remaining (k/s) key: (4432595/1039)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE

the arrival ah sas:

SAS of the CFP on arrival:

outgoing esp sas:
SPI: 0xE82A86BC (3895101116)
transform: esp-3des esp-sha-hmac.
running parameters = {Tunnel}
Conn ID: 2001, flow_id: C83X_MBRD:1, crypto card: IPVPN_MAP
calendar of his: service life remaining (k/s) key: (4432508/1039)
Size IV: 8 bytes
support for replay detection: Y
Status: ACTIVE

outgoing ah sas:

outgoing CFP sas:
Site-382-831 #.

Site-382-831 #.
Site-382-831 #show crypto ipsec his | Pkts Inc. | life
#pkts program: 2397, #pkts encrypt: 2397, #pkts digest: 2397
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
calendar of his: service life remaining (k/s) key: (4486831/862)
calendar of his: service life remaining (k/s) key: (4486738/862)
#pkts program: 2397, #pkts encrypt: 2397, #pkts digest: 2397
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
calendar of his: service life remaining (k/s) key: (4432595/846)
calendar of his: service life remaining (k/s) key: (4432501/846)
Site-382-831 #.

Site-382-831 #.
Site-382-831 #show crypto isakmp policy

World IKE policy
Priority protection Suite 10
encryption algorithm: three key triple a
hash algorithm: Secure Hash Standard
authentication method: pre-shared Key
Diffie-Hellman group: #1 (768 bits)
lifetime: 86400 seconds, no volume limit
Default protection suite
encryption algorithm: - Data Encryption STANDARD (56-bit keys).
hash algorithm: Secure Hash Standard
authentication method: Rivest-Shamir-Adleman Signature
Diffie-Hellman group: #1 (768 bits)
lifetime: 86400 seconds, no volume limit
Site-382-831 #.

Site-382-831 #show crypto card
"IPVPN_MAP" 101-isakmp ipsec crypto map
Description: at the 2nd KC BGP 2821 - PRI - B
Peer = 208.YY. ZZ.11
Extend the PRI - B IP access list
access list PRI - B allowed will host 74.WW. XX.35 the host 208.YY. ZZ.11
Current counterpart: 208.YY. ZZ.11
Life safety association: 4608000 Kbytes / 3600 seconds
PFS (Y/N): N
Transform sets = {}
IPVPN,
}

"IPVPN_MAP" 201-isakmp ipsec crypto map
Description: 2nd Dallas BGP 2821 - s-B
Peer = 208.XX. YY.11
Expand the list of IP SEC-B access
s - B allowed will host 74.WW access list. XX.35 the host 208.XX. YY.11
Current counterpart: 208.XX. YY.11
Life safety association: 4608000 Kbytes / 3600 seconds
PFS (Y/N): N
Transform sets = {}
IPVPN,
}
Interfaces using crypto card IPVPN_MAP:
Ethernet1
Site-382-831 #.

Tunnel between KC & the remote site configuration is:

Distance c831 - KC

crypto ISAKMP policy 10
BA 3des
preshared authentication
!
PRI-B-382 address 208.YY isakmp encryption key. ZZ.11
!
Crypto ipsec transform-set esp-3des esp-sha-hmac IPVPN
transport mode
!
IPVPN_MAP 101 ipsec-isakmp crypto map
Description of 2nd KC BGP 2821 - PRI - B
set of peer 208.YY. ZZ.11
game of transformation-IPVPN
match address PRI - B
!
interface Tunnel101
Description % connected to the 2nd KC BGP 2821 - PRI - B
IP 1.3.82.46 255.255.255.252
IP mtu 1500
KeepAlive 3 3
IP virtual-reassembly
IP tcp adjust-mss 1360
source of tunnel Ethernet1
destination of the 208.YY tunnel. ZZ.11
!
interface Ethernet0
private network Description
IP 10.3.82.10 255.255.255.0
IP mtu 1500
no downtime
!
interface Ethernet1
IP 74.WW. XX.35 255.255.255.248
IP mtu 1500
automatic duplex
IP virtual-reassembly
card crypto IPVPN_MAP
no downtime
!
PRI - B extended IP access list
allow accord 74.WW the host. XX.35 the host 208.YY. ZZ.11
!

KC-2821 *.

PRI-B-382 address 74.WW isakmp encryption key. XX.35
!
PRI-B-382 extended IP access list
allow accord 208.YY the host. ZZ.11 the host 74.WW. XX.35
!
IPVPN_MAP 382 ipsec-isakmp crypto map
Description % connected to the 2nd KC BGP 2821
set of peer 74.WW. XX.35
game of transformation-IPVPN
match address PRI-B-382
!
interface Tunnel382
Description %.
IP 1.3.82.45 255.255.255.252
KeepAlive 3 3
IP virtual-reassembly
IP tcp adjust-mss 1360
IP 1400 MTU
delay of 40000
tunnel of 208.YY origin. ZZ.11
destination of the 74.WW tunnel. XX.35
!
end

Any help would be much appreciated!

Mark

Hello

logs on Site-382-831, only see the crypt but none decrypts, could you check a corresponding entry on the peer and see if has any questions send return traffic?

Site-382-831 #show crypto ipsec his | Pkts Inc. | life
#pkts program: 2397, #pkts encrypt: 2397, #pkts digest: 2397
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
calendar of his: service life remaining (k/s) key: (4486831/862)
calendar of his: service life remaining (k/s) key: (4486738/862)
#pkts program: 2397, #pkts encrypt: 2397, #pkts digest: 2397
#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, #pkts compr. has failed: 0
#pkts not unpacked: 0, #pkts decompress failed: 0
calendar of his: service life remaining (k/s) key: (4432595/846)
calendar of his: service life remaining (k/s) key: (4432501/846)
Site-382-831 #.

Kind regards

Averroès.

Router (IPSec)-> INTERNET-> Router (IPsec) where to put the TUNNEL IP POOL?

Hello

I'm still learning the VPN (IPsec), I was able to create a tunnel between my PC and my router, but now I want to connect two routers:

F0/1=192.168.0.1 ROUTER A-> INTERNET-> ROUTER B F0/1=192.168.10.1

Both routers receive an IP address from my ISP, I can't do a ping to a site at the other site, I mean, I am able to PING ROUTER A from ROUTER B with the ISP addresses and otherwise.

Two ROUTERS have the same configuration, except for the IP addresses and the ACL, they are opposite.

I think I know what I did wrong, but I don't know how to solve: the TUNNEL need also an IP from a POOL where should I put up, the ROUTER A or ROUTER B?

ROUTER

version 12.4

horodateurs service debug datetime msec

Log service timestamps datetime msec

no password encryption service

!

router host name

!

boot-start-marker

boot-end-marker

!

No aaa new-model

IP cef

!

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

ISAKMP crypto key cisco address 81.83.201.BB

!

!

Crypto ipsec transform-set esp-3des RIGHT

!

router_A_to_router_B 1000 ipsec-isakmp crypto map

set of peer 81.83.201.BB

transformation-RIGHT game

match address 101

!

interface FastEthernet0/0

DHCP IP address

automatic speed

full-duplex

router_A_to_router_B card crypto

!

interface FastEthernet0/1

the IP 192.168.0.1 255.255.255.0

automatic speed

full-duplex

!

!

no ip address of the http server

no ip http secure server

!

access-list 101 permit ip 192.168.0.0 0.0.0.255 192.168.10.0 0.0.0.255

!

!

control plan

!

Line con 0

Speed 115200

line to 0

line vty 0 4

!

!

end

ROUTER B

version 12.4

horodateurs service debug datetime msec

Log service timestamps datetime msec

no password encryption service

!

router host name

!

boot-start-marker

boot-end-marker

!

No aaa new-model

IP cef

!

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

ISAKMP crypto key cisco address 81.83.201.AA

!

!

Crypto ipsec transform-set esp-3des RIGHT

!

router_B_to_router_A 1000 ipsec-isakmp crypto map

set of peer 81.83.201.AA

transformation-RIGHT game

match address 101

!

interface FastEthernet0/0

DHCP IP address

automatic speed

full-duplex

router_B_to_router_A card crypto

!

interface FastEthernet0/1

IP 192.168.10.1 255.255.255.0

automatic speed

full-duplex

!

!

no ip address of the http server

no ip http secure server

!

access-list 101 permit ip 192.168.10.0 0.0.0.255 192.168.0.0 0.0.0.255

!

!

control plan

!

Line con 0

Speed 115200

line to 0

line vty 0 4

!

!

end

!

!

!

!

!

!

Best regards

Didier

Didier, there are a number of things missing in your config file to make it work, what I can say fa0/1 is inside and the fa0/0 are outdoors. There is no NAT translation to activate the computers inside the network, allowing access to the Internet. You will also need to exclude the EIGRP NAT roads in order to reach the remote network. Each router must have a default gateway to the Internet, this should be done with the following command:

IP route 0.0.0.0 0.0.0.0 fa0/0 dhcp

This will use the default gateway of the DHCP server that assigns IP address on fa0/0. Once that each router has a path to another and the tunnel connects EIGRP will handle the rest given the information to the router 90, this is the spectacle of one of my spoke routers route:

NTR-2620XM #show ip route
Code: C - connected, S - static, mobile R - RIP, M-, B - BGP
D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone
N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2
E1 - OSPF external type 1, E2 - external OSPF of type 2
i - IS - Su - summary IS, L1 - IS - IS level 1, L2 - IS level - 2
-IS inter area, * - candidate failure, U - static route by user
o - ODR, P - periodic downloaded route static

Gateway of last resort is to network 0.0.0.0 0.0.0.0

65.0.0.0/32 is divided into subnets, subnets 1
C 65.14.24.190 is directly connected, Dialer0
172.16.0.0/32 is divided into subnets, subnets 1
D EX 172.16.50.31 [170/3074560] via 172.19.8.1, 20:04:58, Tunnel0
172.19.0.0/24 is divided into subnets, subnets 1
C 172.19.8.0 is directly connected, Tunnel0
10.0.0.0/8 is variably divided into subnets, subnets 14, 6 masks
D EX 10.13.13.8/29 [170/2818560] via 172.19.8.1, 20:04:58, Tunnel0
D EX 10.11.7.0/28 [170/2818560] via 172.19.8.1, 20:04:58, Tunnel0
D 10.13.13.0/29 [90/2818560] via 172.19.8.1, 20:04:58, Tunnel0
C 10.19.9.0/27 is directly connected, Vlan200
C 10.19.8.0/24 is directly connected, Vlan100
C 10.19.10.0/28 is directly connected, Vlan900
D EX 10.20.7.0/24 [170/2818560] via 172.19.8.1, 20:04:58, Tunnel0
D [90/3097600] 10.22.7.0/24 through 172.19.8.1, 17:34:52, Tunnel0
D 10.37.4.0/24 [90/3074560] via 172.19.8.1, 20:04:59, Tunnel0
D 10.15.50.0/24 [90/3074560] via 172.19.8.1, 20:04:59, Tunnel0
D EX 10.24.40.0/24 [170/2818560] via 172.19.8.1, 20:04:59, Tunnel0
D 10.12.85.0/24 [90/3074560] via 172.19.8.1, 20:04:59, Tunnel0
C 10.19.9.192/26 is directly connected, Vlan500
D EX 10.244.0.0/22 [170/2818560] via 172.19.8.1, 20:04:59, Tunnel0
74.0.0.0/32 is divided into subnets, subnets 1
C 74.23.201.24 is directly connected, Dialer0
S * 0.0.0.0/0 is directly connected, Dialer0

All designated routes D are dynamic routes drawn other routers on the DMVPN EIGRP. It will propagate the routing table and they point to the appropriate star. If you follow the example that I gave you, you will have a functional DMVPN.

See you soon,.

Sam

Implementation of the remote access VPN IPSec using SRI 2801

Hello

I tried to set up a VPN for remote access using 2801 SRI. I've been able to establish my house vpn tunnel using the DSL (behind a NAT) connection, give it SRI the IP address that is in the ip pool I configured on safety. The problem I have right now is that it does not reach the company LAN network.

DIAGRAM:

MODEM PC (VPN CLIENT) ADSL - ROUTER SOHO - INTERNET - ISR2801 - LAN---(10.10.0.27&192.168.0.9) COMPANY

PC: 172.16.10.122

SOHO ROUTER LAN IP: 172.16.10.254

SOHO ROUTER WAN IP: Dynamically assigned by ISP

ISR2801 WAN IP: x.x.x.5/224

IP LAN ISR2801: 10.10.0.50/24

The CORPORATE LAN subnet: 10.10.0.0/24 and 192.168.0.9/24

2801 SRI CONFIGURATION:

AAA new-model

!

!

connection of AAA NOCAUTHEN group local RADIUS authentication

local NOCAUTHOR AAA authorization network

!

!

IP domain name xxxxx.com

!

!

!

username root password 7 120B551806095F01386A

!

!

crypto ISAKMP policy 3

BA 3des

preshared authentication

Group 2

ISAKMP crypto 5 40 keepalive

ISAKMP crypto nat keepalive 20

!

Configuration group isakmp crypto-GROUP NOC client

touch [email protected]/ * /! ~ $ 9876 qwerty

DNS 192.168.0.9

192.168.0.9 victories

xxxxx.com field

LWOP-pool

include-local-lan

netmask 255.255.255.0

!

!

Crypto ipsec transform-set AC - SET esp-3des esp-sha-hmac

!

dynamic-map crypto NOC-DYNAMICMAP 10

transformation-LWOP-SET game

!

!

list of crypto AC-customer card NOCAUTHEN card authentication

list of crypto isakmp NOCAUTHOR AC-card card authorization

crypto map CNP-map client configuration address respond

Crypto map AC - map 10-isakmp dynamic ipsec AC-DYNAMICMAP

!

!

!

!

interface FastEthernet0/0

IP address x.x.x.5 255.255.255.224

Speed 100

full-duplex

card crypto AC-map

!

interface FastEthernet0/1

IP 10.10.0.50 255.255.255.0

Speed 100

full-duplex

!

local IP NOC-POOL 192.168.250.101 pool 192.168.250.110

IP route 0.0.0.0 0.0.0.0 XXX1

IP route 10.10.0.0 255.255.255.0 10.10.0.10

IP route 172.16.10.0 255.255.255.0 FastEthernet0/0

Route IP 192.168.0.0 255.255.255.0 10.10.0.10

IP route 192.168.250.0 255.255.255.0 FastEthernet0/0

!

I have attached a few screenshots. My goal here is to have access to my LAN to the company (10.10.0.0/24 and 192.168.0.9/24). I don't know what is missing here.

No, we don't need not NAT. wanted to confirm if NAT could cause this problem.

The config looks good. Can you ping routers ip internal interface the client LAN once it connects?

Are correct, w.r.t. transatlantic lines reaching pool behind router VPN?

If so, I would like to take a look at the exits following when a client is connected.

See the crypto eli

ISAKMP crypto to show his

Crypto ipsec to show his

SPSP

No Internet VPN IPsec Tunnel access

Similar Questions

Maybe you are looking for