ASA cx does not not with traffic redirection

Similar Questions

• VPN site to site thanks to a pair of asa 5505 does not pass traffic

  the configurations are fairly simple. Ping between the two lan pc fails. "show isakmp crypto his" and "crypto ipsec to show his" got out, if.

  Please refer to the attached text and diagram files.

  I'm pre-configures the ASA, for external interfaces have ip addresses private for the moment.

  all entries are welcome.

  Thank you!

  Your look simple configurations.

  As the Phase 1 and Phase 2 SAs are coming, the VPN seems correct.

  We see program leaving ASA1 and decaps ASA2, but no return traffic seems to come in.

  I suspect a problem with the host 192.168.102.5. Can you capture the top packages and check that it receives traffic initiated from the host 192.168.101.5 (side ASA1) and he answers with the ASA2 as its default gateway?

• ASA 8.3 VPN site-to-site does not UDP traffic to other peer

  Hello!!!

  Someone turned off the lights :-) I say this because that's 6.2 6.3 I can't get the basic things...

  On a SAA, I created a "site-site" VPN profile to connect to a remote site, on the other side (ASA 8.2) sees no problem, I can pass all IP traffic via VPN without NAT; but on a new ASA5505 with 8.3 (1) version fw and ASDM 6.3 (1) can't do that in any way :-(

  What I get is trivial...

  ... It works perfectly with TCP and ICMP traffic, but does not have UDP traffic: in practice, if I followed the traffic to a remote private IP, TCP and ICMP traffic I see only packets in vlan "inside" with the private IP, but with the UDP traffic on top of that, I see traffic on vlan 'out' with the IP public ASA and source port changed :

  Inside: UDP to 172.16.2.128:6000 to 172.16.0.200:6000
  Outside: UDP to 5.5.5.5:23400 to 172.16.0.200:6000

  Why?

  Of course, the traffic is not encrypted and does not reach the other side of the tunnel!

  Here are the important parts of the configuration:

  interface Vlan1
  nameif inside
  security-level 100
  172.16.2.1 IP address 255.255.255.0

  network obj_any object
  subnet 0.0.0.0 0.0.0.0

  remote network object
  172.16.0.0 subnet 255.255.254.0

  outside_cryptomap to access extended list ip 172.16.2.0 allow 255.255.255.0 network remote control object

  NAT (inside, outside) static source any any destination static remote-remote network

  network obj_any object

  NAT dynamic interface (indoor, outdoor)

  card crypto outside_map0 1 match address outside_cryptomap

  outside_map0 card crypto 1jeu pfs

  card crypto outside_map0 1 set ip.ip.ip.ip counterpart

  outside_map0 card crypto 1jeu nat-t-disable

  outside_map0 interface card crypto outside

  Given that the new business object, I have not yet quite clear (ok, I don't find time to do a deep reading of the documentation), someone is able to direct me to fix this trivial?

  Note: If I remove my drive manual nat and I flag "network translating" on the remote network object thus indicate that they want NAT with ip network remote control then don't work any IP vs. remote site traffic. Why, why have not more than the simple rules of 'nat exception' the old version and why the crypto-plan applies only to TCP traffic? Possible that there is an object any which takes all IP traffic?

  A big thank you to all.

  73,

  Arturo

  Hi Arturo,.

  I know that there is a certain NAT related bugs in 8.3 (1) and although I don't remember a specific which corresponds to your symptoms, I would say you try 8.3 (2) instead, or maybe even the last available version of a temp (currently to 8.3 (2.4):)

  http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=8.3.2+Interim&mdfid=279916854&sftType=Adaptive+Security+Appliance+%28ASA%29+Software&optPlat=&nodecount=9&edesignator=null&modelName=Cisco+ASA+5510+Adaptive+Security+Appliance&treeMdfId=268438162&modifmdfid=&imname=&treeName=Security&hybrid=Y&imst=N

  If you still see the problem, then, check

  entry Packet-trace within the udp 172.16.2.2 1025 172.16.0.1 detail 123

  entry Packet-trace inside tcp 172.16.2.2 1025 172.16.0.1 detail 123

  and check what's different.

  HTH

  Herbert

• Router firewall does not block traffic

  Hello

  I use vmware view Home 4.6 client.  I can authenticate and connect to a windows image 7, but only a black screen appears.  After about 30 seconds it disconnects with the error "the connection to the remote computer has ended."

  If I disable my billion router firewall, the machine virtual windows 7 appears and everything works as expected.  I tried port forwarding 4172 and 5002 but still does not work.  Then I tried port forwarding 50000 to 65000 I saw various 50456 to 64652 ports in firewall logs.  TCP and UDP are enabled in both cases, but no luck.

  Here is the part of the firewall log:

  04 August 23:01:38 home.gateway:firewall:info: 476378.910 blocked Prot = 17, 192.168.1.1:56143 > 10.100.200.1:137 - default defense

  04 August 23:01:38 home.gateway:firewall:info: 476378.910 blocked Prot = 17, 192.168.1.1:52771 > 10.100.200.1:137 - default defense

  04 August 23:01:38 home.gateway:firewall:info: 476378.910 blocked Prot = 17, 192.168.1.1:64632 > 10.100.200.1:137 - default defense

  192.168.1.1 is my computer and 10.100.200.1 is my domain controller from work.

  I then tried to create a packet filtering rule to allow 4172, then 50000 to 65000, but nothing worked.  To disable the firewall of the router or select the parameter of low security for her is the only way to operate.  The default medium security setting blocks the traffic.

  Router is a VGP 7301 billion.  Any advice would be much appreciated.  Thank you.

  Hello

  Im sorry im not familiar with this particular modem however I got something similar on my draytek at home. Mine to connect for a few seconds, and then stop working.

  I discovered that it was because my BACK settings on my modem have been set to protect against a stream of UDP. I was able to disable then part of security BACK settings and then it worked ok.

  Maybe it's the little, you have problems with that. I have no port forwarding on my configuration, and im sure I wasn't leaving the installation rules, all incoming traffic is blocked.

  I hope this helps.

  See you soon

  Phil

  [Edit]

  Just checked, I 32111 outgoing tcp (redirect usb) and also 4172 TCP/UDP outgoing (pcoip). Nothing, nothing allowed incoming traffic.

• I just spent an hour to compose a response in a thread ("Firefox does not with paypal"), only to see "You do not have permission" to submit - total loss!

  I was connected to respond in the thread "Firefox does not work with paypal. I spent the best part of an hour carefully compose this response, case tests, links, etc... [Tip: Firefox, unlike other browsers, has a problem with the server paypalobjects.comscripts.] Because I had taken so long to write the answer, she seemed to be a good idea to check in via the Preview button, but I received a message that the service was not available. Of course, I decided to submit it anyway, but when I hit 'submit' I got a message "you don't have permission...". "- at which point I (stupidly) on another page with this message, and what I wrote was gone!

  Anyway, it is definitely not normal that the site log out after only an hour. Sorry to hear about this. Maybe there was a little problem on the server with your session. If it is reproducible, I wonder if you have any software that could be quietly elimination of cookies for the inactive sites?

• Satellite Pro 2100 - works does not with 2 sticks of RAM

  Hi all

  I've been with sticks of 2 x 512 MB RAM from a reliable supplier that reassures me that this RAM is compatible with the SP2100 laptop.

  With the two sticks installed, as soon as the machine is running, I get no display and 5 beeps (1 long, a follow-up of 4 short beeps). Each stick of RAM work well individually, and I also tested slot A and b. Thus, the 2 sticks of RAM are working alone and work the two slots. It seems that this machine has a problem with 2 sticks of RAM.

  The ACPI BIOS is up to date (v1.40). I also tried the old 256 MB stick with one of the new sticks of 512 MB - same problem. I tried this as the supplier of memory mentioned this Toshiba may take only 1 GB maximum.

  Any ideas why two sticks of RAM does not work?

  Thanks in advance and amicably.

  James

  Hello

  You are right. The laptop must be able to manage memory 1024Mo. (2 x 512 MB)
  Due to your description, I think that both modules are compatible, but cannot play together.
  In my opinion, you should use two modules with the same specifications

  Try to use the modules recommended by Toshiba;
  PC2100 256 MB (PA3127U - 1 M 25)
  PC2100 512 MB (PA3164U - 1 M 51)

• I have a MBP Late 2013 will pair does not with 6s on Blutooth

  Read all comments (lots of old stuff on these communities) and tried all the suggestions of trashing the plist etc etc. Still unable to get my iPhone 6s to pair with my MBP end 2013.

  For a fleeting moment after that match it says connected not connected appears.

  AirDrop works, but my phone does not appear on the screen of the devices. If sending photos of the iPhone works well my avatar is not displayed as sender just my intials & where ever he gets the ints info not the name I use in my Contacts.

  Someone at - it any idea what is happening. This worked OK until recently.

  An iPhone will pair not via Bluetooth to a computer (Mac or Windows) with the exception of hotspot and then only if your cell phone plan he supports. See below for more information. https://discussions.Apple.com/docs/doc-7722

  If you try to use the procedure of transfer/continuity or AirDrop, which does not have Bluetooth but devices don't are NOT matched. Bluetooth must be just on and the devices within range of the other. The following may help in problems of transfer/continuity: https://support.apple.com/en-us/HT204678

• Active state with menu manual not working does not with child pages

  I created a horizontal menu manual on my master page with two links (at WORK and about me). I did them manually as it was the only way I could work out how the style and the menu items to distance as I wanted. I created an active state that works for the main page WORK and the about me page.

  However, I have four child pages under the work, but when you click on one of them that the active State for labor (a green line under work) does not appear. When I return to the menu options to try to "solve" the problem and choose "All pages" all child pages appear in the main menu I want and does not solve the problem. I chose manual that I could put the line to show that under the term of WORK and not all field.

  Here is my Web site to demonstrate the problem: www.robertgreens.com

  Any help to fix this would be appreciated with gratitude!

  I managed to solve this problem (with the help of Live Chat Support). I needed to create an autour work and provide a 'normal' State which resembled the active state, so when you click on the pages of the child, it looked like work page parent menu (with a green line) below. This meant that I had to duplicate master page and do the same (deletion of the green line in the menu of work) for the words Me page. And now, everything looks the same: www.robertgreens.com

• Audio fun does not with animation

  I think it must have something to do with the audio being does not correctly placed on the timeline, but I think I do everything that the directions said. When I put audio in the timeline, it will play the audio from the beginning, but if I stop the audio and try to play a place randomly in the Middle, it won't play anything. How can I fix so the audio will play anywhere in the animation, not only at the beginning?

  If you publish a swf file, use stream to sync the sound, no event property.

• JDBC connection does not with ORA-12514

  Hi all

  I also have problems with the connection to the DB CARS because the listener does not recognize the name of the service. I read many messages from the forum itself here and elsewhere and I just can't understand it. Everything seems in order, so I'm a little confused as to why it does not work.

  Thus, some specifications: I actually use SAP as advanced application to connect to the DB.

  DB is RAC 11203, two nodes.

  OS: Linux RH6

  Headphones and remote headphones are a race to the top.

  JDBC connection string fails:

  JDBC:Oracle:Thin:@(Description=(Address=(Protocol=TCP)(Host=virtualhost1)(port=1527))(Address=(Protocol=TCP)(Host=virtualhost2)(port=1527)) (CONNECT_DATA = (SERVICE_NAME = MYSERVICENAME. «"" WORLD)))»»»

  I check that the service is available in the cluster:

  ORA. < dbname >. myServiceName.svc online on physicalhostname1

  When I check the status of the listener on node1 he mentions the MYSERVICENAME downstairs so it's here

  [oracle@physicalhost1 bin] $ lsnrctl serv < DBNAME >. WORLD

  LSNRCTL for Linux: Version 11.2.0.3.0 - Production on 2013-SEP-07 16:43:11

  Copyright (c) 1991, 2011, Oracle.  All rights reserved.

  Connection to (DESCRIPTION = (SDU = 32768) (ADDRESS = (= SAP COMMUNITY. (World) (Protocol = TCP (port = 1527))(Host=virtualhost1)) (LOAD_BALANCE = OFF)(Failover=on) (CONNECT_DATA = (GLOBAL_NAME = < DBNAME >. WORLD) (SERVICE_NAME = < DBNAME >. «"" WORLD)))»»»
  Summary of services...
  Service '< DBNAME >' has 1 instance (s).
  Instance ' < DBNAME > 001 ", State LOAN, has 1 operation for this service...
  Managers:
  "DEDICATED" set up: 0 denied: 0 status: ready
  LOCAL SERVER
  Service ' < DBNAME > 001 "has 2 occurrences.
  Instance ' < DBNAME > 001 ', status UNKNOWN, has 1 operation for this service...
  Managers:
  "DEDICATED" set up: 0 denied: 0
  LOCAL SERVER
  Instance ' < DBNAME > 001 ", State LOAN, has 1 operation for this service...
  Managers:
  "DEDICATED" set up: 0 denied: 0 status: ready
  LOCAL SERVER
  Service ' < DBNAME > 002 "a 2 occurrences.
  Instance ' < DBNAME > 001 ", State LOAN, has 1 operation for this service...
  Managers:
  "DEDICATED" set up: 0 denied: 0 status: ready
  LOCAL SERVER
  Instance ' < DBNAME > 002 ", status UNKNOWN, has 1 operation for this service...
  Managers:
  "DEDICATED" set up: 0 denied: 0
  LOCAL SERVER
  Service "MYSERVICENAME" has 1 instance (s).
  Instance ' < DBNAME > 001 ", State LOAN, has 1 operation for this service...
  Managers:
  "DEDICATED" set up: 0 denied: 0 status: ready
  LOCAL SERVER
  The command completed successfully

  When I check the node database in sqlplus

  SQL > show the service_name parameter

  VALUE OF TYPE NAME
  ------------------------------------ ----------- ------------------------------
  service name string < DBNAME > 002, < DBNAME > 001, < DBNAME >, myservicename

  That's where. The database is running.

  I am spent days on this and I am unable to understand. I tried to re - register the name of service to SIR with lowercase, uppercase. In fact, when I joined the service I used capital letters, do not know why crsstat it shows always lowercase. Also in sqlplus I see lowercase. I do know that if it's case sensitive at all, but shows the despair that I really tried everything. I think that the fact that I am using SAP is not serious as long as any application - what is uses the thin JDBC connection string.

  Help, please.

  Your JDBC connection string requires a service MYSERVICENAME. WORLD, it should be MYSERVICENAME.

• Solution for "Spooler service does not" with printers HP F4480 all-in-one.

  If you receive the prompt that says: "cannot install or print due to 'queue service does not work', here is a simple solution.»

  GO to the start menu and click on 'run '.

  Type CMD, and then click OK

  Type in the box that appears, "net start spooler" and click ENTER.

  NOTE: Without quotes and spaces between net start spooler.

  The box invites you... spooler is now in service.  The printer should now work correctly.

  Great information.

• Distributed form works does not with hotmail or gmail

  Sorry, if this is in the wrong place, but desperate to find an answer. (This form is about to circulate among a few hundred grade 12 students, who will have a wide range of messaging options.  We have students do not have difficulties to send this form)

  I have a form, distributed, sent people to fill out the form (test first) and submit.  Which I will collect in the entering e-mail response file.

  
  Some fill out the form, send, he calls the window to use gmail, hotmail or office.  They select Office/outlook sends exactly according to the needs. Excellent.
  
  But from time to time, it does not yet give the possibility for the Office or hotmail, it automatically changes to outlook.  Which I think would be OK, if the student is on their home computer and want to send it like that. (but eventually will be their parents email)

  For those who are informed on a school computer and want to use hotmail/gmail.  several problems occur...
  Once they choose the choice of hotmail/gmail, the process does not continue.  Everything seems to disappear, and the form is never received by the expected collector. Never turns in the gmail/hotmail sent file.
  
  One person said, they thought that it went through the process... but the collector never received.
  
  One person said, it doesn't give them the choice... it automatically opens outlook, even if they would have used hotmail instead.
  

  I suspect that most of the students would use a hotmail/gmail account to send the form.

  It's the form, we have created, http://www.SD22.BC.ca/forms/Scholarship_Application_Final_distributed.PDF  

  If it helps to understand what is happening... appreciate anyone taking a peek, even try to present.  Just write on her test, so that we know.

  We are trying to get this ready for the end of February.

  Perhaps recognizing the help... This should be posted on another forum as well. ?

  Total egg on my face.  The people who described the problem for me, left aside the fact that they did not actually read the pop up window that came when they hit the submit button.

  This explains, so why no one really had an answer for me.  The popup window, when you choose 'internet' option indicates clearly that we must save, then fix on the mail program they choose.

  My apologies, there...

  But he did raise the small problem, if someone check marking the 'don't show this'... could cause problems.

• 1inc Strip everywhere at the tool bar does not with the mouse... all else ok.but cannot sign out of mail ' cos in this band

  1inc band less than search and bookmarks... nothing doesn't work with mouse inside so can not disconnect because déconnexion comes in this band... can not scroll top because arrow in this band.everything otherwise ok. Google and internet explore is ok... everything works fine for them only on mozilla firefox... which is what I use all the time

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the extensions or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > appearance/themes).

  • Makes no changes on the start safe mode window.
  • https://support.Mozilla.com/kb/safe+mode
  • https://support.Mozilla.com/kb/troubleshooting+extensions+and+themes

• Magic mouse 2 scrolling does not with windows 10

  I installed windows via boot camp 10. Now when I start with windows, I can move the magic mouse 2 on the screen but the scrolling with the mouse works do not. When I start with Osx 10.11.4 mouse Magic 2 doesn't have a problem.

  have you installed the bootcamp drivers that you create within the bootcamp utility in OS X?

• Exporting does not with El Capitan

  After that I installed and updated my computer a few days ago, everything seems to work smooth EXCEPT for the most important part... Export of... If someone knows how to fix this problem without having to downgrade my OS you will be my Savior... I really need to send video out to a customer, and now I'm past the deadline :-/

  I solved the problem with first only export do not.  I uninstalled the creative cloud just like applications (first, After Effects, Photoshop and Lightroom more) then just re-installed the creative cloud and applications.  Now, it seems right to export.  And the whole process takes about an hour.  Hope this helps if anyone has the same problem.