ASA: Equivalent to the pdm on a Pix command.

Similar Questions

• series PIX command authorization

  Hi all

  can someone tell me please the use of GBA pix command authorization. I understand the use of a shell command authorization.

  I'm sorry if the question is too dumb. I am completely new to this sector.

  Thanks in advance.

  concerning

  Kirti.

  Pix command authorization set was designed to set up approval order with PIX/FWSM, as shell pix did not differ for IOS, but at the launch the actual code, PIX/FWSM seems to work correctly with the auth command sets the shell.

  So no one is really interested in using shell Pix more, more to watch new codes of pix it seems that developers are more likely making Pix Shell same shell IOS, so even if they stop PIX command sets in the next version of ACS I will not be surprised.

  ~ Rohit

• Help the Site VPN Site PIX 501

  Hello

  I'm pretty new to PIX firewall, so I hope someone here can help me.

  I have two PIX and try to create a private network virtual between the two PIX. I posted the configs below.

  The problem is that I can ping PIX on a PIX two, but I can't ping the servers behind TWO PIX. On two PIX, I cannot ping PIX ONE or all the servers behind it.

  Any advice would be appreciated.

  Thank you

  PIX 1

  6.2 (2) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  hostname TMAXWALES

  domain ciscopix.com

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  inside_outbound_nat0_acl ip 192.168.254.0 access list allow 255.255.255.0 192.1

  68.1.0 255.255.255.0

  outside_cryptomap_20 ip 192.168.254.0 access list allow 255.255.255.0 192.168.1

  .0 255.255.255.0

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside of *. *.198.139 255.255.255.248

  IP address inside 192.168.254.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 192.168.254.10 255.255.255.255 inside

  location of PDM 192.168.1.0 255.255.255.0 outside

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137

  Timeout xlate 03:00

  Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR

  p 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.254.10 255.255.255.255 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  outside_map 20 ipsec-isakmp crypto map

  card crypto outside_map 20 match address outside_cryptomap_20

  card crypto outside_map 20 peers set *. *.198.138

  outside_map crypto 20 card value transform-set ESP-3DES-SHA

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address *. *.198.138 netmask 255.255.255.255 No.-xauth non - co

  Nfig-mode

  part of pre authentication ISAKMP policy 20

  ISAKMP policy 20 3des encryption

  ISAKMP policy 20 chopping sha

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  Telnet timeout 5

  SSH timeout 5

  Terminal width 80

  PIX 2

  6.2 (2) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  hostname tmaxbangor

  domain ciscopix.com

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 192.168

  . 254.0 255.255.255.0

  permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 192.168.254

  .0 255.255.255.0

  pager lines 24

  opening of session

  debug logging in buffered memory

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside of *. *.198.138 255.255.255.248

  IP address inside 192.168.1.1 255.255.255.0

  IP verify reverse path to the outside interface

  IP verify reverse path inside interface

  the IP audit info action alarm reset drop

  reset the IP audit attack alarm drop action

  location of PDM 192.168.1.0 255.255.255.0 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137

  Timeout xlate 03:00

  Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR

  p 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  http 192.84.7.111 255.255.255.255 inside

  http 192.168.1.10 255.255.255.255 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  outside_map 20 ipsec-isakmp crypto map

  card crypto outside_map 20 match address outside_cryptomap_20

  card crypto outside_map 20 peers set *. *.198.139

  outside_map crypto 20 card value transform-set ESP-3DES-SHA

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address *. *.198.139 netmask 255.255.255.255 No.-xauth non - co

  Nfig-mode

  part of pre authentication ISAKMP policy 20

  ISAKMP policy 20 3des encryption

  ISAKMP policy 20 chopping sha

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  Telnet 192.168.1.0 255.255.255.0 inside

  Telnet timeout 50

  SSH timeout 5

  Terminal width 80

  Can't see anything obviously wrong with the configs. You have these connected back to back on the same subnet, it looks that it even if you have xxx out IP addresses? If so it's maybe a routing problem, in what they send everything to the default gateway of xxx.x.198.137 rather than to the other.

  Try to add a static route to the remote subnet to each PIX that points directly to the peer, so on PIX1 you should have:

  Route outside 192.168.1.0 255.255.255.0 xxx.x.198.138

  and on PIX2 do:

  Route outside 192.168.254.0 255.255.255.0 xxx.x.198.139

  and see if that makes a difference. Note that you wouldn't encounter this problem when these two PIX is on separate networks and uses the default gateway for all routing decisions.

  If this still fails, run 'debug cryp isa' and ' debug cry ipsec "on the two PIX are trying to build a tunnel again, and then and send us the output.

  Also, make sure your tests that you're rattling to a host behind a PIX to a host behind the other PIX, ping PIX to PIX or host because of PIX that won't test your VPN connection.

• Accessing the PDM in read-only mode

  Hi all.

  I have a Pix with ver 6.3 and I want to allow access to the customer in read-only mode.

  I usually don't use aaa and privileges to avoid locking issues, but now it seems that I have to face the issue.

  I have 2 questions:

  A. is the next plan safe (enough) to avoid blocking?

  1. username admin password * priv 15

  2. username pdmuser password * priv 5

  3 aaa authentication http LOCAL console

  4. level 5 privilege control?

  B. what shoul commands assign the privilege 5 level to allow the user see the welcome and the tracking completely Page?

  Thank you

  Michele

  Hi Michele,

  A. Yes, it is safe and sufficient not to lockout the pix. Infact, your console/telnet will not be affected, only the PDM with the above configuration in place.

  B. There are three levels different priv for PDM, monitor (level 3), read-only (level5) and admin (level 15). So level monitor is all that he needs to go to the Home Page and monitoring page. Here is the procedure:

  Turn on the AAA for PDM:

  -System Properties

  -Admin Pix

  Authentication/authorization

  -Check HTTP/PDM

  -Select service LOCAL group

  -Box ENBALE AUTHORIZATION

  -Select service LOCAL group

  Creatting users:

  -User-> user with level 15 and 3 (monitor) account

  Thank you

  Renault.

• Information on the routing of traffic of the client VPN to PIX.

  Hey all,.

  I could follow the VPN Wizard included in the PDM and able to connect with the VPN Clients for the PIX. But I'm looking for more information about how the routing is done.

  For example, my remote is 67.71.252.xxx and my inside is 192.168.1.xxx. But if I connect via VPN to PIX Client, all data is transferred through my VPN to PIX and then trying to get out to the Internet.

  I'll settle for data goes 192.168.1.xxx for transit through the VPN. This configuration made via the PIX or is it the responsibility of the Client machine to set up rules of the road?

  All links to the guides to installation, or technical notes would be great.

  Thank you inadvance.

  Paul

  Hello

  I think the key word you are looking for is "split tunneling". This can be validated on the PIX using the vpngroup split access_list tunnel GroupName command.

  "Split tunneling allows a remote VPN client or encrypted simultaneous Easy VPN remote access device to the corporate network and Internet access. Using the vpngroup split-tunnel command, specify the access list name with which to associate the split tunneling of traffic. "

  In this example configuration: http://www.cisco.com/warp/public/110/pix3000.html, note that the same access list is used to "nat 0" and split-mining:

  access-list 101 permit ip 10.1.1.0 255.255.255.0 10.1.2.0 255.255.255.0

  (Inside) NAT 0-list of access 101

  vpngroup vpn3000 split tunnel 101

  Order reference:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2120/products_command_reference_chapter09186a00801727ae.html#wp1099471

  Please let us know if this helped

  Kind regards

  Mustafa

• Cannot open the PDM file with excel 2016

  Hey guys,.

  I have Office 2016, LV 2015 and (I checked my "TDM Excel Add-in" file) the Excel Add-in 2015 of CT.

  I have attached a picture of what I get when I try to open the PDM file with excel.

  So, I found something strange. I checked active supplements under the excel options and the TDM Excel Add-in is listed as inactive (and is called a COM-add-in). I tried to activate it, by checking the box (see the second picture), but that does not change. Interesting is the last line of my second attached photo:

  Translated it means: ' loading behavior: a runtime error occurred when trying to load this Add-In.

  I have 10-64 bit operating system like windows.

  Someone at - it a solution?

  Kind regards

  Slev1n

  
  

• the last equivalent to the PCI-6024E

  What is the last product NOR equivalent to the PCI-6024E

  OR recommend the PCIe-6321.  It's a bit the connector is different.

• How to write the Date/time of the PDM file property

  On the page root of the PDM file, there is a predefined, property called ' Date/Time' in the first row.

  I would use it to save the timestamp when the tdms file is created. But in the help file.

  I find that the following property constant. So, how can I write to the field of property ' Date/time '?

  Property	Constant	Data type
  Name	TDMS_FILE_NAME	String (char *)
  Description	TDMS_FILE_DESCRIPTION	String (char *)
  Title	TDMS_FILE_TITLE	String (char *)
  Author	TDMS_FILE_AUTHOR	String (char *)

  Thanks for any idea or suggestion.

  You are not sure if it's exactly what you want, but have you tried that?

  CVIAbsoluteTime            CVItime, *t = NULL;
  TDMSFileHandle          deH = 0;
  
  // Create TDMS file and set some properties
  errChk (TDMS_CreateFileEx (file, TDMS_Streaming2_0, TDMS_ByteOrderNative, 0,"example.tdm", "someText", "title", "author", &deH));
  
  // ...
  
  GetCurrentCVIAbsoluteTime (&CVItime);
  errChk (TDMS_SetFileProperty (deH, "Date/Time", TDMS_Timestamp, CVItime));
  
  // ...
  
  // Save and close fileerrChk (TDMS_SaveFile (deH));TDMS_CloseFile (deH);
  

• maximum length of the PDM file

  Hi amazing if I could be a good idea, really cannot relearn the hard way!

  If we record to 500kS/s PDM file, is there a length/size, after which data are not added in the PDM columns more? Or he keeps the connection until windows launches the message that the system is out of memory?

  Thank you very much

  Waris K

  I guess it's the limitations of file system. For example, you use FAT32 if 4 GB maximum file size. If you are using NTFS, it should be 16TB (!).

  /Y

• The PDM Property Ordinance

  Hello

  I would like to know if there is a way for the PDM file properties to be arranged in order the information has been saved.

  I recorded for example date, author, devices used and the others in the file properties

  If I want to use tdms Viewer info are not arranged the order of writing. I guess it's more or less normal knowing that it resembles a database

  but is it always possible to force the display order?

  Best regards

  Tinnitus

  'TDMS get properties' already returns the properties in the order that they were written in. It's the TDMS files viewer that sorts the list alphabetically by property.

  TDMS file viewer is a VI and not protected. If you need to display the properties in their order real, all you need to do is to remove the de.\vi.lib\Utility\tdmsutil.llb\formatPropertyList.vi sort code (that's the two loops on the right side).

  Herbert

• Is a pavement of Chromebook equivalent to the right button of the mouse?

  Is a pavement of Chromebook equivalent to the right button of the mouse?

  When I click on the lower right of the trackpad, it clicks Open the link thank instead of giving me a menu to choose options such as "Open in new tab", "open in a new window", etc.

  Thanks for your help.

  Thanks to someone else give me the link to a user of Chromebook guide, I found the answer.

  Click on a link with two fingers instead of one to produce the functionality of the right button of the mouse.

• Player.exe ceased to operate or get error game has stopped working because of the pdm.keylogger

  a few games that I download to play will not play keep the computer saying player.exe stopped working on other games, I get the message stopped working because of the pdm.keylogger I'd love to be able to play these games any ideals thanks

  a few games that I download to play will not play keep the computer saying player.exe stopped working on other games, I get the message stopped working because of the pdm.keylogger I'd love to be able to play these games any ideals thanks

  The problem seems to be related as a result of security Kaspersky you use. Try to disable Kaspersky and reload the game (s).

• ASA using only the IPS?

  Hello

  It is possible to use the ASA with IPS-Module as sensor only, located with its external interface on a mirrored switch port?

  Kind regards.

  Volker

  The external interface is for command and control only and cannot be used for monitoring.

  The SSM is only able to monitor traffic passing by the ASA.

  The ASA does not support the connection ports to ports switched mirror either.

  The closest you get is to configure the ASA is transparent with ACLs on each interface that allow all traffic and then place the ASA between 2 of your existing devices. And then place a policy on the SAA to copy all packages to the SSM for surveillance of promiscuity.

  If you have another type of firewall, existing installation, you can try placing the ASA transparent among other things your firewall and your DMZ switch for example.

  All traffic would be passed through the ASA and copied in the SSM for surveillance of promiscuity.

  This mode could better be described as using the ASA as a simulated click to send traffic to the SSM.

• is there anyone knows the equivalent of the swing component blackberry user interface?

  Hello

  I just need to know blackberry equivalent of the user interface of the swing components.

  y at - it someone who knows it.

  There is also no equivalent ImageObserver.

  Many times if I do a port that has this I have just remove because the initial goal is almost always to notify the caller when the image is done drawing/be converted (format from one image to another, etc.).

  On BlackBerry, there are a total of 3 types (Image, image Bitmap, EncodedImage) the image and can relatively easily be passed from one to the other quickly so that eliminates one of the uses and the drawing is very fast or throws an error if it cannot be traced so that eliminates the use of the second.

  So it is not necessary (at least in my opinion).

• All Cisco ASA 5510 have the IPS modules

  I am new to the use of Cisco Networking products. I gave me a mission to determine if our company 5510 and 5505 IPS/IDS. In doing my research I discoververed 5505 have no IPS/IDS, but you can buy a card and 5510 have modules IPS/IDS. How can I determine whether my 5510 modue (s) IPS/IDS

  only the new x (but not the 5585) ASAs have software modules. There on the 5505 and 5510 hw modules. But first, you must bring your ASA-access in the order. You can try different browsers, but also make sure that your Java is up to date.

  Sent by Cisco Support technique iPad App